Herman Miller Setu Lounge Chair and Ottoman User Manual

Y

Tools Required:

Setu® Disassembly for Recycling

2 lbs Hammer

Utility Knife Rubber Mallet

T-20 Torx Driver

(2.75” or longer)

Power Driver Small Flathead

Screwdriver

Safety GlassesT-27 Torx Bit

Materials Identication and Segregation:

Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should

be treated as mixed plastic. Ferrous metals can be identied using a small magnet for

recycling. Non-ferrous metals should be separated and recycled separately.

Disassembly Steps:

1.1 Lay chair on back.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Caster

2.1 Grasp and pull to remove
Casters from the Base.

Part no. 1b5vn8 rev B.

1

Rubber Mallet

3.1 Hold Base legs rmly and

strike the bottom of cylinder
with rubber mallet until Base
comes loose.
Caution:

directly with metal hammer, use
rubber mallet only!

Height Adjustment
Cable

Screwdriver

Do not strike cylinder

4.1 Remove Base.

5.1 Use small Flathead
Screwdriver to disengage
black plastic connector of
Height Adjustment Cable
from top of Cylinder.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

6.1 Use small Flathead
Screwdriver to disengage
ball of Height Adjustment
Cable from top of Cylinder.

Part no. 1b5vn8 rev B.

2

Hit hammer here

7.1 Place one hand on can of
Cylinder and hit the bottom of
the chair with hammer until
Cylinder seperates from chair.

T-20 Torx

Driver

8.1 Remove Cylinder.

9.1 Use a T-20 Torx Driver to
remove screws.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

10.1 Remove Height
Adjustment Assembly.

Part no. 1b5vn8 rev B.

3

Power Driver

11.1 Using a Utility Knife cut
Seat Fabric in half.

12.1 Using a Power Driver with a
T-27 bit, remove Shoulder Bolts.

12.2 Remove Shoulder Bolts.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b5vn8 rev B.

4

13.1 Using a Power Driver
with a T-27 bit, remove Bolts.

14.1 Remove Arms. 15.1 Remove Inner Bushing.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b5vn8 rev B.

5

16.1 Remove T-Nut from Arm. 17.1 Remove No Arm Plug
from opening in Beam.

18.1 Remove T-Nut from No

Arm Plug.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b5vn8 rev B.

6

19.1 Using a Power Driver with a

T-27 bit, remove Shoulder Bolts.

20.1 Remove Inner Bushings.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b5vn8 rev B.

7

21.1 Using a Powerdrill with

22.1 Remove Tilt Assembly

a T-27 bit, remove Screws.

23.1 Using a Powerdrill with a

from Seat Assembly.

24.1 Remove Rear Links.

T-27 bit, remove Shoulder Bolts.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b5vn8 rev B.

8

25.1 Remove Shoulder Bolts

using Power Driver.

26.1 Remove 4 Inner Bushings.

27.1 Remove Front link.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

28.1 Using a small shaft or
screwdriver. Remove pressed
T-Nut from both Links.

Part no. 1b5vn8 rev B.

9

T-Nut Location

29.1 Pull Fabric out of groove in
Seat frames to remove. Remove
metal clips from fabric.

30.1 Remove T-Nuts from
Seat frame.

Z

© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Setu are among the registered trademarks of Herman Miller, Inc.

TM

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b5vn8 rev B.

10