Herman Miller SAYL Chairs User Manual

Download

Page 1

Tools Required:

SAYL® Disassembly for Recycling

Flat Screw Driver

Power driver

T-40 Torx Driver

Hammer

Nose Plier

Safety Glasses

Rubber Mallet

Materials Identication and Segregation:

Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should

be treated as mixed plastic. Ferrous metals can be identied using a small magnet

for recycling. Non-ferrous metals should be separated and recycled separately.

Steps:

to remove caster from base.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

2. Remove all casters.1. Hold base and pull hard

Part no. 1b9rth rev A.

Page 2

3. Hold base legs rmly and

4. Disengage the base from strike the bottom of cylinder with a rubber mallet until base comes loose.

cylinder.

5. Place one hand on can of cylinder and hit with hammer.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

6. Remove cylinder.

Part no. 1b9rth rev A.

Page 3

7. Pull arm to the highest

8. Using nose plier

position.

depress the retention clip.

9. Pull off the retention clip.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

10. Depress the lock inward and pull the arm up to remove.

Part no. 1b9rth rev A.

Page 4

11. Repeat 7 to 10 steps to

Note: If removing a no arm

remove other side arm.

plug, depress the lock inward as in step 10 and remove arm plug.

12. Using T-20 torx driver remove arm pad screws (4 screws for adjustable pad,

1 screw for xed pad.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

13. Slide pad forward and off.

Part no. 1b9rth rev A.

Page 5

14. Lay chair on back. Using

at head screw driver pry

away (both sides until seat lock bar comes out).

15. Remove lock bar.

16. Release the seat lock move seat to the backward position.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

17. Lift upward to remove.

Part no. 1b9rth rev A.

Page 6

18. Remove all 4 T-20 torx

19. Remove seat skirt. Seat

screws.

skirt is also held on by 4 clips. Carefully pull the seat skirt loose from these clips. With screw driver pry out and remove any clips that remain lodged in the seat frame.

20. Slide latch to outside of seat frame until tabs are disengaged.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

21. Unsnap the latch from seat frame and remove spring.

Part no. 1b9rth rev A.

Page 7

22. Remove the upholstery

23. Remove the seat foam

from seat.

from the seat bottom.

24. Using a power driver with T-40 torx remove top bolt.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

25. Remove the bolt from tilt assembly.

Part no. 1b9rth rev A.

Page 8

26. Remove the plate from

27. Using T-40 torx remove

the tilt assembly.

2 screws from tilt assembly.

28. Remove bottom screw.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

29. Slide off the back assembly.

Part no. 1b9rth rev A.

Page 9

30. Remove top screws from

31. Turn it over and remove each side using a T-25 torx from the frame.

back attachment screws using a T-20 torx.

32. Remove back attachment screws using a torx T-40.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

33. Remove pelvis.

Part no. 1b9rth rev A.

Page 10

34. Using hand slightly pull

35. Insert a screw driver and back the spine from the back and remove the spine bracket plate from bottom of the back.

rotate to expand the clip.

36. Pull spine off the back.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

37. Use a T-20 torx wrench

remove 1 screw from each pivot joint.

Part no. 1b9rth rev A.

Page 11

38. Using T-25 torx remove 1 screw from each sleeve.

39. Pull sleeve off the back.

40. Slide out the plastic nut plate from slot towards bottom of the back.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

41. Using thumb & fore

nger squeeze handle snaps

together.

Part no. 1b9rth rev A.

Page 12

42. Remove lumbar handle. 43. Pull the upholstery from back.

44. Pull the foam and remove

from back.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

45. Remove scrim material from foam.

Part no. 1b9rth rev A.

Page 13

46. Using a nose plier remove

47. After disassembling hook on the bottom of the lumbar assembly.

one side, pull the bow back so that it does not engage again.

48. Remove lumbar from back insert.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

49. Remove suspension

material.

Part no. 1b9rth rev A.

Page 14

50. Pry the tab towards front

51. Pull out the handle

of the tilt.

assembly from tilt.

52. Slide off the lever form the assembly.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

53. Pry the other side tab towards front of the tilt and pull out the lever.

Part no. 1b9rth rev A.

Page 15

54. Slide off the other side

55. Pull off the tilt cover from

lever from the assembly.

tilt assembly.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b9rth rev A.

Page 16

Side Chair:

1. Using philip head screw driver remove screw from front underside of seat pan.

2. Pull up on rear of cushion to disengage snap and slide seat cushion forward.

3. Using a power driver with a T-20 torx bit remove screws in seat pan.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

4. Slide seat pan rearward until all tabs are disengaged.

Part no. 1b9rth rev A.

Page 17

5. Using a power driver with

6. Using a rubber mallet tap a T-15 torx bit remove arm screws from back side.

on bottom of arm until arm comes out.

7. Pull off arms from both sides.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

8. Pull or tap upward to

remove back.

Part no. 1b9rth rev A.

Page 18

9. Clamp on to a glide using

10. Place a rigid spacer a vice grip and tap vice grip using a rubber mallet until glide comes out. Repeat the step on other legs to remove the remaining 3 glides.

between wheels on the body of caster and tap on it with a rubber mallet until caster wheel assembly comes off. Repeat the step on other legs to remove the remaining 3 casters.

11. Clamp on to a caster receptacle using a vice grip and tap vice grip using a rubber mallet until receptacle comes out.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

12. Carefully slide ngers

between front fabric cover

and frame, pull rmly. Pull corners rst and then center.

Part no. 1b9rth rev A.

Page 19

13. Remove the fabric from

14. Remove fabric plastic back

foam.

panel.

15. Pull the suspension material from back and remove.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

16. Using a phillip head screw driver remove all screws from retainer.

Part no. 1b9rth rev A.

Page 20

17. Remove the retainer from seat back.

18. Repeat step 16 to 17 remove rest of the pieces.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b9rth rev A.

Herman Miller SAYL Chairs User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual