HermanMiller Locale T-Desk, Locale L-Desk Installation And Operating Instructions Manual

TM

Locale

L-Desk and T-Desk Installation

Y

LOCALE HEIGHT ADJUSTABLE DESK OPERATING INSTRUCTIONS

CAUTION: WHEN OPERATING THIS DESK, MAKE SURE TO REMOVE ANY OBJECTS OR OBSTRUCTIONS THAT COULD BE IN THE WAY OF

THE MOVING DESK TOP. The rated load For the desk

is 200 lbs. maximum.

1) To operate the height adjustable desk, press the up or down arrows on the control switch located under the front edge of the desk top.

2) Press the up arrow to move the desk top higher.

3) Press the down arrow to move the desk top lower.

Control Switch

PARAMÈTRES RÉGIONAUX RÉGLABLE EN HAUTEUR BUREAU INSTRUCTION DE FONCTIONNEMENT

ATTENTION : LORS DE L’UTILISATION DE CE BUREAU, ASSUREZ-VOUS DE RETIRER

TOUT OBJESCTS OU OBSTRUCTIONS QUI POURRAIENT ÊTRE DANS LA FACON DE LE

DEPLACER DESSUS DE BUREAU. LA CHARGE NOMINAL POUR LE BUREAU EST DE

90.7 KG MAXIMUM.

1) Pour faire fonctionner la hauteur réglable de bureau, appuyez sur les èches vers le haut ou le bassur le commutateur de commande situé sous le bord du bureau.

2) Appuyez sur la èche vers le haut pour déplacer le desk top supérieur.

3) Appuyez sur la èche vers le bas pour déplacer le bureau inférieur le plus

haut.

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1bch5g rev D.

1

L-Desk

(Shown throughout instructions)

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

T-Desk

Part no. 1bch5g rev D.

2

Parts Included:

A

Base Assembly

B

Upper Case

Base Top

C

M6 x 20 Socket Flange Head Screw(8)

F

Rail

K

Column Shroud

G

Work Surface Support

L

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

D

M

Column

Wire Guide

H

M8 x 30 Socket Flat Head Machine Screw(12)

M8 x 16 Hex Socket Head Machine

E

Screw (4)

End Column

J

N

Control Switch

Part no. 1bch5g rev D.

3

Motor Cable Power Cable

P R

Work Surface

V

M5 x 12 Socket Button Flange Head Machine

Z

Screw(22)

T

Cable Clamp

Control Box

W

Service Chain

U

M5 x 12 Socket Button Head Cap Screw(4)

X

Y

Mushroom Fastener(6)

AA

AD

AC

AE

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Grommet Clamp(2)

Shelf(2)

AF

M3.5 x 12 Plastite Pozi Pan Head

Screw

Shelf Pins(8)

Cable Tray

AB

AJ

Wire Tray

M5 x 16 Socket Button Head Flange Screw(6)

AG

Clamping Screw

Part no. 1bch5g rev D.

4

AH

Dowel Pin

AK

M5 x 10 Flange Head Screw(3)

M8 x 25 Hex Socket

AN

Head Machine Screw (4)

Tools Needed:

Power Driver

Access Panel

#2 Phillips Bit

Door

Level

AL

3mm Metric Hex Bit

Column Leg

4mm Metric Hex Bit

AM

5mm Metric Hex Bit

A

Leg Glide

6mm Metric Hex Bit

Door

Access Panel

1. Place Base at desired location.

2. Open or remove Doors.

3. Remove Access Panels by pulling out at top of panel, then lifting up and out.

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1bch5g rev D.

5

Outside Glide

Inside Glide

Bottom Shelf

4. Remove Bottom Shelves from Base.

5. Level base by adjusting Outside Glides rst. Then adjust Inside Glides down

to touch oor.

(Note: View shown with top panel removed for clarity.)

D

C

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

6. If More than one unit are to be installeded in a run; position adjoining unit next to one already in position.

7. Level and align that unit to mate with other.

8. Connect bases with 4 Clamping Screws (C) and 1 Dowel Pin (D).

Part no. 1bch5g rev D.

6

Access Cover

9. Remove Access Covers from Base End Panels.

10. Install Electrical Harnesses to Base.

Break Out

11. Break out opening in Access Covers if required.

12. Return Access covers to Base.

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1bch5g rev D.

7

B

C

F

13. Position Base Top (C) or Upper Case(B) onto Base. Secure to Base with 8 Pan Head Machine Screws (F).

J J

AL

AM

T-Desk

14. Turn Glides (AM) into Column Leg (AL).

15. Attach Column Leg to End Column (J) with 4 Hex Socket Head Machine Screws (AN) with the torque 130 inch lbs or 15 Nm force.

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

AN

AL

AM

L-Desk, RH

AN

J

AL

AM

L-Desk, LH

AN

Part no. 1bch5g rev D.

8

D

Level

Top Screws

E

Bottom Screws

16. Assemble Column(s) (D) to Base with 4 Socket Head Machine Screws (E).

17. Fully Tighten Top Screws. Loosely tighten Bottom Screws.

18. Move lower end end of column until Level on top casting shows true.

19. Fully tighten Bottom Screws.

Y

AJ

Y

20. Determine which side of Work Surface Wire Cover will be accessed from. Attach Mushroom Fastener (Y) to Column and End Column with Flange Screws (AJ) where cover will latch. Image shows correct position for T-Desk.

AJ

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1bch5g rev D.

9

J

M

L

K

21. Place End Column (J) bottom side up.

22. Set Rails (K) onto Column (J).

23. Position Work Surface Support (L) onto Rail.

24. Secure all together with 6 Flat Head Machine Screws (M).

M

L

M

25. Place the assembly onto the Column.

26. Position the other Work Surface Support (K) onto Rail.

27. Secure all in place with 6 Flat Head Machine Screws (L).

Z

TM

Sense, Setu, Tu, Traverse and Locale are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1bch5g rev D.

10

HermanMiller Locale T-Desk, Locale L-Desk Installation And Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual