Herman Miller Celle Chairs User Manual

Download

Tools Required:

Celle® Disassembly for Recycling

Safety Glasses

Flat

Screwdriver

Rubber Mallet

Nose Plier

Allen Wrench

Ratchet Wrench

Phillips

Screwdriver

Snap Ring

Materials Identication and Segregation:

Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should

be treated as mixed plastic. Ferrous metals can be identied using a small magnet

for recycling. Non-ferrous metals should be separated and recycled separately.

Steps:

Plier

1. To remove the frame cap,

using a at screwdriver pry

the frame cap.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

2. Pull off the frame cap.

Part no. 1b9vtd rev A.

3. Using a T-30 Torx allen

4. Release the back seat wrench remove both side screws from seat frame.

5. Remove seat back from

snaps from seat frame.

6. Using needle nose pliers,

the back seat frame.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

remove height adjustment

cable from cable tting and

slide cable T-end from height adjust lever.

Part no. 1b9vtd rev A.

7. Using a straight head

8. Hold down adjustable screwdriver, pry retaining clip from seat frame and set clip aside. Repeat to remove from other side.

slide lever on adjustable seat.

9. Slide seat forward until interlock tabs on seat are fully disengaged from interlock tabs on seat linkage.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

10. Disengage the height adjustment slide lever snaps by hand from seat frame and pull off.

Part no. 1b9vtd rev A.

11. Using a snap ring plier,

12. Using hand pull off the remove snap ring, washer and foam spacer.

13. Using hand pull off the tilt limit lever.

seat angle lever.

14. Using ratchet wrench

and T-40 torx bit, remove

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

and save screws securing back support to tilt housing. Repeat for opposite back support.

Part no. 1b9vtd rev A.

15. Using a straight head

16. Using a T-20 Torx head screwdriver, pry bottom of frame insert up and out of each support frame. Slide back support frames partially out of tilt .

screwdriver remove the screw from frame insert. Repeat the step to remove the screw from other side frame.

17. Remove frame inserts and remove lumbar from back support frames.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

18. Remove both side seat

frames.

Part no. 1b9vtd rev A.

19. Using allen wrench

20. Remove the steel remove the two screws from steel weldment.

21. Using straight head

weldment.

22. Pull exible cover back

screwdriver, pry up and remove x-mas tree clip, securing rear tilt cover to tilt housing. Dispose of x-mas tree clip properly.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

and up. Slowly lift cover to

disengage remaining exible

interlock features and set cover aside.

Part no. 1b9vtd rev A.

23. Using ratchet wrench

24. Remove arm from tilt and T-40 Torx bit, remove the screws from the tilt assembly.

25. Insert small straight head screwdriver into hole

assembly.

26.Lift xed arm assembly

up off arm support stem.

on inside of xed arm. Push

inward to release internal

latch holding xed arm in

place.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b9vtd rev A.

27. Slide arm pad to

28. Remove arm pad

outermost position and insert straight head screwdriver against inside of retainer clip. Pry clip outward while lifting up on arm pad.

29. Using ratchet and T-27

properly.

30. Using ratchet and T-40 Torx bit, remove and save screws (noted) that secure one side of seat linkage assembly to tilt assembly. Repeat for opposite side of seat linkage assembly.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Torx bit, remove seat linkage pivot bolts and bushings. Remove seat linkage side covers from tilt assembly.

Part no. 1b9vtd rev A.

31. Remove tilt tension adjustment knob by pulling knob from shaft by hand.

32. Insert a screwdriver

behind the tilt cover push forward and remove the tilt cover.

33. Using needle nose pliers, remove & save height adjust cable from top of pneumatic cylinder.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

34. Place pneumatic

cylinder knock out tool with open end over end of pneumatic cylinder. Make sure tool rests squarely on top rim of pneumatic cylinder.

Part no. 1b9vtd rev A.

35. Support tilt/base

36. Disengage the snaps

assembly off oor and strike

cylinder knock out tool sharply with a medium size hammer to dislodge pneumatic cylinder from tilt.

from the base.

37. Pull off the base cap from cylinder.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

38. Hold base and pull hard to remove caster from base.

Part no. 1b9vtd rev A.

39. Using straight head

40. Using straight head screwdriver, pry off retainer clip from bottom of base and set aside.

screwdriver, pry up on base weldment with screwdriver blade in slot as shown. To disengage leg of base weldment from cover. Repeat for remaining legs.

41. Remove cover from base weldment and set aside.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

42. Remove fabric from back.

Part no. 1b9vtd rev A.

43. Remove the foam from

44. Remove the fabric from back.

seat.

45. Remove the foam from seat.

Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Part no. 1b9vtd rev A.

Herman Miller Celle Chairs User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual