HERCULES 57673 Owner's Manual & Safety Instructions

Page 1
Owner’s Manual & Safety Instructions
20i
Model
HE77
10″ COMPACT JOBSITE TABLE SAW
WITH RACK & PINION FENCE
WARNING: To prevent serious injury, user must read and
When unpacking, make sure that the product is intact and
undamaged. If any parts are missing or broken, please call
1-888-866-5797 as soon as possible. Reference 57673
Page 2
IMPORTANT SAFETY INFORMATION
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e. When operating a power tool outdoors,
use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of
a GFCI reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energizing power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent
use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause
severe injury within a fraction of a second.
i. Only use safety equipment that has been
approved by an appropriate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area.
j. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
k. Do not leave the tool unattended when
it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving.
l. This product is not a toy.
Keep it out of reach of children.
Page 2 For technical questions, please call 1-888-866-5797. Item 57673
Page 3
m. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with Trigger locked on.
• Properly maintain and inspect to avoid electrical shock.
• Properly ground power cord. Ground Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock.
n. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power
source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools and accessories.
Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces
dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a
qualified repair person using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
b. Maintain labels and nameplates on the tool.
These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
6. Safety instructions for mitre saws
a. Mitre saws are intended to cut wood or
wood-like products, they cannot be used with abrasive cut-off wheels for cutting ferrous material such as bars, rods, studs, etc. Abrasive dust causes moving
parts such as the lower guard to jam. Sparks from abrasive cutting will burn the lower guard, the kerf insert and other parts.
b. Use clamps to support the workpiece
whenever possible. If supporting the workpiece by hand, you must always keep your hand at least 100 mm from either side of the saw blade. Do not use this saw to cut pieces that are too small to be securely clamped or held by hand. If your hand is
placed too close to the saw blade, there is an increased risk of injury from blade contact.
c. The workpiece must be stationary and
clamped or held against both the fence and the table. Do not feed the workpiece into the blade or cut ″freehand″ in any way.
Unrestrained or moving workpieces could
be thrown at high speeds, causing injury.
d. Push the saw through the workpiece. Do
not pull the saw through the workpiece. To make a cut, raise the saw head and pull it out over the workpiece without cutting, start the motor, press the saw head down and push the saw through the workpiece. Cutting on
the pull stroke is likely to cause the saw blade to climb on top of the workpiece and violently throw the blade assembly towards the operator.
e. Never cross your hand over the intended
line of cutting either in front or behind the saw blade. Supporting the workpiece
″cross handed″ i.e. holding the workpiece
to the right of the saw blade with your left hand or vice versa is very dangerous.
Page 3For technical questions, please call 1-888-866-5797.Item 57673
Page 4
f. Do not reach behind the fence with either
hand closer than 100 mm from either side of the saw blade, to remove wood scraps, or for any other reason while the blade is spinning. The proximity of the
spinning saw blade to your hand may not be obvious and you may be seriously injured.
g. Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make certain that there is no gap between the workpiece, fence and table along the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the spinning saw blade while cutting. There should be no nails or foreign objects in the workpiece.
h. Do not use the saw until the table is clear
of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of
wood or other objects that contact the revolving blade can be thrown with high speed.
i. Cut only one workpiece at a time.
Stacked multiple workpieces cannot be adequately clamped or braced and may bind on the blade or shift during cutting.
j. Ensure the mitre saw is mounted or placed
on a level, firm work surface before use.
A level and firm work surface reduces the risk of the mitre saw becoming unstable.
k. Plan your work. Every time you change the
bevel or mitre angle setting, make sure the adjustable fence is set correctly to support the workpiece and will not interfere with the blade or the guarding system. Without
turning the tool ″ON″ and with no workpiece
on the table, move the saw blade through a complete simulated cut to assure there will be no interference or danger of cutting the fence.
l. Provide adequate support such as table
extensions, saw horses, etc. for a workpiece that is wider or longer than the table top.
Workpieces longer or wider than the mitre saw table can tip if not securely supported. If the cut­off piece or workpiece tips, it can lift the lower guard or be thrown by the spinning blade.
m. Do not use another person as a substitute
for a table extension or as additional support. Unstable support for the workpiece
can cause the blade to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade.
n. The cut-off piece must not be jammed or
pressed by any means against the spinning saw blade. If confined, i.e. using length
stops, the cut-off piece could get wedged against them blade and thrown violently.
o. Always use a clamp or a fixture designed
to properly support round material such as rods or tubing. Rods have a tendency to roll
while being cut, causing the blade to ″bite″ and
pull the work with your hand into the blade.
p. Let the blade reach full speed before
contacting the workpiece. This will reduce
the risk of the workpiece being thrown.
q. If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving parts to stop and disconnect the plug from the power source and/or remove the battery pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could cause loss of control or damage to the .mitre saw.
r. After finishing the cut, release the switch,
hold the saw head down and wait for the blade to stop before removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
s. Hold the handle firmly when making an
incomplete cut or when releasing the switch before the saw head is completely in the down position. The braking action of the
saw may cause the saw head to be suddenly pulled downward, causing a risk of injury.
7. Guarding related warnings
a. Keep guards in place. Guards must be in
working order and be properly mounted. A guard that is loose, damaged, or is not functioning correctly must be repaired or replaced.
b. Always use saw blade guard, Riving Knife
and anti-kickback device for every through­cutting operation. For through-cutting operations
where the saw blade cuts completely through the thickness of the workpiece, the guard and other safety devices help reduce the risk of injury.
c. Immediately reattach the guarding system
after completing an operation (such as rabbeting, dadoing or resawing cuts) which requires removal of the guard, Riving Knife and/or anti-kickback device.
The guard, Riving Knife, and anti-kickback device help to reduce the risk of injury.
d. Make sure the saw blade is not contacting
the guard, Riving Knife or the workpiece before the switch is turned on. Inadvertent
contact of these items with the saw blade could cause a hazardous condition.
e. Adjust the Riving Knife as described in this
instruction manual. Incorrect spacing, positioning
and alignment can make the Riving Knife ineffective in reducing the likelihood of kickback.
Page 4 For technical questions, please call 1-888-866-5797. Item 57673
Page 5
f. For the Riving Knife and anti-kickback
device to work, they must be engaged in the workpiece. The Riving Knife and anti-kickback
device are ineffective when cutting workpieces that are too short to be engaged with the Riving Knife and anti-kickback device. Under these conditions a kickback cannot be prevented by the Riving Knife and anti-kickback device.
g. Use the appropriate saw blade for the
Riving Knife. For the Riving Knife to function
properly, the saw blade diameter must match the appropriate Riving Knife and the body of the saw blade must be thinner than the thickness of the Riving Knife and the cutting width of the saw blade must be wider than the thickness of the Riving Knife.
8. Cutting procedures warnings
a. DANGER: Never place your fingers or
hands In the vicinity or in line with the saw blade. A moment of inattention or a
slip could direct your hand towards the saw blade and result in serious personal injury.
b. Feed the workpiece into the saw blade
only against the direction of rotation.
Feeding the workpiece in the same direction that the saw blade is rotating above the table may result in the workpiece, and your hand, being pulled into the saw blade.
c. Never use the miter gauge to feed the
workpiece when ripping and do not use the Rip Fence as a length stop when cross cutting with the miter gauge. Guiding
the workpiece with the Rip Fence and the miter gauge at the same time increases the likelihood of saw blade binding and kickback.
d. When ripping, always apply the workpiece
feeding force between the fence and the saw blade. Use a push stick when the
distance between the fence and the saw blade is less than 150mm, and use a push block when this distance is less than 50mm. “Work helping” devices will keep your hand at a safe distance from the saw blade.
e. Use only the push stick provided by the
manufacturer or constructed in accordance with the instructions. This push stick provides
sufficient distance of the hand from the saw blade.
f. Never use a damaged or cut push stick.
A damaged push stick may break causing your hand to slip into the saw blade.
g. Do not perform any operation “freehand”.
Always use either the Rip Fence or the miter gauge to position and guide the workpiece. “Freehand’ means using your hands to support or guide the workpiece, in lieu of a Rip Fence or miter gauge. Freehand sawing leads to misalignment, binding and kickback.
h. Never reach around or over a rotating saw
blade. Reaching for a workpiece may lead to
accidental contact with the moving saw blade.
i. Provide auxiliary workpiece support to the
rear and/or sides of the saw table for long and/or wide workpieces to keep them level.
A long and/or wide workpiece has a tendency to pivot on the table’s edge, causing loss of control, saw blade binding and kickback.
j. Feed workpiece at an even pace. Do not bend
or twist the workpiece. If jamming occurs, turn the tool off Immediately, unplug the tool then clear the jam. Jamming the saw blade by the workpiece can cause kickback or stall the motor.
k. Do not remove pieces of cut-off material while
the saw is running. The material may become
trapped between the fence or inside the saw blade guard and the saw blade pulling your fingers into the saw blade. Turn the saw off and wait until the saw blade stops before removing material.
l. Use an auxiliary fence in contact with the
table top when ripping workpieces less than 2mm thick. A thin workpiece may wedge
under the Rip Fence and create a kickback.
9. Kickback causes and related warnings
Kickback is a sudden reaction of the workpiece due to a pinched, jammed saw blade or misaligned line of cut in the workpiece with respect to the saw blade or when a part of the workpiece binds between the saw blade and the Rip Fence or other fixed object.
Most frequently during kickback, the workpiece is lifted from the table by the rear portion of the saw blade and is propelled towards the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
a. Never stand directly in line with the saw blade.
Always position your body on the same side of the saw blade as the fence. Kickback may propel the workpiece at high velocity towards anyone standing in front and in line with the saw blade.
b. Never reach over or in back of the saw blade
to pull or to support the workpiece. Accidental
contact with the saw blade may occur or kickback may drag your fingers into the saw blade.
c. Never hold and press the workpiece
that is being cut off against the rotating saw blade. Pressing the workpiece being
cut off against the saw blade will create a binding condition and kickback.
d. Align the fence to be parallel with the saw
blade. A misaligned fence will pinch the workpiece
against the saw blade and create kickback.
e. Use a featherboard to guide the workpiece
against the table and fence when making non­through cuts such as rabbeting, dadoing or resawing cuts. A featherboard helps to control
the workpiece in the event of a kickback.
Page 5For technical questions, please call 1-888-866-5797.Item 57673
Page 6
f. Use extra caution when making a
cut into blind areas of assembled workpieces. The protruding saw blade may
cut objects that can cause kickback.
g. Support large panels to minimise the risk
of saw blade pinching and kickback. Large
panels tend to sag under their own weight. Support(s) must be placed under all portions of the panel overhanging the table top.
h. Use extra caution when cutting a workpiece
that is twisted, knotted, warped or does not have a straight edge to guide it with a miter gauge or along the fence. A warped,
knotted, or twisted workpiece is unstable and causes misalignment of the kerf with the saw blade, binding and kickback.
i. Never cut more than one workpiece, stacked
vertically or horizontally. The saw blade could
pick up one or more pieces and cause kickback.
j. When restarting the saw with the saw
blade in the workpiece, center the saw blade In the kerf so that the saw teeth are not engaged in the material. If the saw
blade binds, it may lift up the workpiece and cause kickback when the saw is restarted.
k. Keep saw blades clean, sharp, and with
sufficient set. Never use warped saw
blades or saw blades with cracked or broken teeth. Sharp and properly set saw blades minimize binding, stalling and kickback.
10. Table saw operating procedure warnings
a. Turn off the table saw and disconnect
the power cord when removing the table insert, changing the saw blade or making adjustments to the Riving Knife, anti­kickback device or saw blade guard, and when the machine Is left unattended.
Precautionary measures will avoid accidents.
b. Never leave the table saw running unattended.
Turn it off and don’t leave the tool until it comes to a complete stop. An unattended running saw is an uncontrolled hazard.
c. Locate the table saw in a well-lit and level
area where you can maintain good footing and balance. It should be installed in an area
that provides enough room to easily handle the size of your workpiece. Cramped, dark areas, and uneven slippery floors invite accidents.
d. Frequently clean and remove sawdust
from under the saw table and/or the dust collection device. Accumulated sawdust
is combustible and may self-ignite.
e. The table saw must be secured. A table saw
that is not properly secured may move or tip over.
f. Remove tools, wood scraps, etc. from the
table before the table saw is turned on.
Distraction or a potential jam can be dangerous.
g. Always use saw blades with correct size
and shape (diamond versus round) of arbor holes. Saw blades that do not match
the mounting hardware of the saw will run off-center, causing loss of control.
h. Never use damaged or incorrect saw blade
mounting means such as flanges, saw blade washers, bolts or nuts. These mounting
means were specially designed for your saw, for safe operation and optimum performance.
i. Never stand on the table saw, do not
use it as a stepping stool. Serious injury
could occur if the tool is tipped or if the cutting tool is accidentally contacted.
j. Make sure that the saw blade is installed
to rotate in the proper direction. Do not use
grinding wheels, wire brushes, or abrasive wheels on a table saw. Improper saw blade installation or use of accessories not recommended may cause serious injury.
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION READ
AND FOLLOW THESE INSTRUCTIONS:
Grounded Tools: Tools with
Three Prong Plugs
3-Prong Plug and Outlet
1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See 3-Prong Plug and Outlet.)
2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See 3-Prong Plug and Outlet.)
Page 6 For technical questions, please call 1-888-866-5797. Item 57673
Page 7
3. The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)
Double Insulated Tools: Tools
with Two Prong Plugs
TABLE A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
EXTENSION CORD
LENGTH
25´ 50´ 75´ 100´ 150´
Outlets for 2-Prong Plug
1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code.
2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire extension cord. Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A.)
3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Table A.)
5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.
8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.
Vibration Safety
This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.
3. Use tools with the lowest vibration when there is a choice between different processes.
4. Include vibration-free periods each day of work.
5. Grip workpiece as lightly as possible (while still keeping safe control of it). Let the tool do the work.
6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.
Specifications
Electrical Rating 120VAC / 60Hz / 15A
Rated No. Load Speed 4800 RPM
Cutting Capacity at 90° 3-1/8″
Cutting Capacity at 45° 2-1/4″
Maximum Bevel 45°
Maximum Miter 90°
Saw Blade 10″ Diameter
Page 7For technical questions, please call 1-888-866-5797.Item 57673
Page 8
SETUP - BEFORE USE
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Functional Description
Switch
Height/Bevel
Adjustment Handwheel
Scale
Miter Gauge
Bevel Lock
Handle
Saw Blade
Riving
Knife
Bevel Scale
Insert Lock
Blade Guard
Rip Fence
Lock Lever
Pawl
Storage
Rip Fence
Extension Table
Push Stick
Blade Wrench
Storage
Adjusting
Knob
Rail Lock Lever
Table
Insert
Front Rail
Miter Gauge
Locking Knob
Miter Gauge
Groove
Anti-kickback
Pawls
Cable Storage
Dust Extraction
Port
Rear Rail
Page 8 For technical questions, please call 1-888-866-5797. Item 57673
Page 9
Assembly
Removing the Table Insert
Mounting Table Saw
1. Select a workbench or mounting location that is able to support the weight of the Table Saw, plus any additional weight placed on it during use.
2. Make sure there are no hidden electric wires, cables or other obstructions that may interfere with the mounting procedure or cause a hazard.
3. Mark the mounting hole locations at the base of the Saw and drill the appropriate size holes for the mounting bolts (not included).
4. Mount the Saw using bolts, washers and nuts (not included).
Attaching the Handwheel
1. Remove Handwheel from its storage box located underneath the Table Saw.
Storage
Box
1. Lower the blade by turning the Height Adjustment Knob counter-clockwise.
Height Adjustment Knob
2. Lock the blade by turning Bevel Lock Handle clockwise.
2. Remove tape and Set Screw from Handwheel.
3. Place Handwheel on Spindle and align holes on both the Spindle and Handwheel.
Spindle
Bevel Scale
Bevel Lock Handle
3. To remove Table Insert, turn the Insert Lock clockwise. Using finger hole on the insert, pull up and forward to expose the inside of the saw.
Table Insert
Insert Lock
4. To reinstall the table insert: Push insert down in place and turn the Insert Lock counterclockwise.
Handwheel
4. Use Set Screw to fasten Handwheel to the Spindle.
5. Tighten Set Screw.
Page 9For technical questions, please call 1-888-866-5797.Item 57673
Page 10
Adjusting Riving Knife
Removing and Installing the Blade
Note: Riving Knife has three mounting holes for three positions. The uppermost position is for all through cuts. The middle position is for non-through cuts (with blade guard and anti-kickback pawls removed). The down position is only used for shipping.
In uppermost position for through cuts
In middle position for non-through cuts
In down position for shipping
Note: Riving Knife follows the saw blade to keep the kerf (gap) from closing on the saw blade. Reposition the Riving Knife before initial use.
1. With Table Insert removed, rotate Lock Lever up and pull the Riving Knife toward right side of the saw to release it from lock pin. This will allow the knife to slide up and down.
Riving Knife
NOTICE: To work properly, the saw blade teeth
must point down toward the front of the saw. Failure to heed this instruction could cause damage to the saw blade, the saw or the workpiece.
WARNING! Make sure that the saw blade is installed to rotate in the proper direction. Do not use grinding wheels, wire brushes, or abrasive wheels on a table saw. Improper saw blade installation or use of accessories not recommended may cause serious injury. When installing the saw blade, wear protective gloves. Danger of injury when touching the saw blade.
WARNING! Only use a 10″ saw blade with a 5/8″
arbor, rated to at least 4,800 RPM and intended for woodcutting. To avoid serious injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.
1. To remove the blade, unplug saw. Turn Height Adjustment Knob clockwise to raise blade to maximum height. Remove Table Insert.
2. Remove the Blade Wrench from storage area.
Lock Lever
2. Bring Riving Knife up so that the lock pin is re-engaged into bottom mounting hole.
3. Pull Lock Lever forward, locking Riving Knife in uppermost position.
Lock Lever
4. Once the blade is installed and Riving Knife adjusted to its working setting, replace table insert.
Blade Wrench
3. Turn the Arbor Nut with the blade wrench and at the same time, pull Spindle Lock Lever until it engages. Keep lever pulled and loosen nut by turning in a counterclockwise direction.
4. Remove Arbor Nut, Outer Blade Flange and Saw Blade.
Blade Wrench
Spindle
Lock Lever
Arbor
Inner
Outer Blade
Flange
Arbor Nut
Blade
Flange
Saw Blade
Note: All parts must be clean before assembly.
5. To install the blade, place new saw blade onto the Inner Blade Flange of the tool arbor.
Page 10 For technical questions, please call 1-888-866-5797. Item 57673
Page 11
WARNING! TO PREVENT SERIOUS INJURY: When installing the saw blade, make sure that the saw blade teeth point down at the front side of blade.
6. Place Outer Flange and Arbor Nut on arbor.
7. Turn Arbor Nut with the blade wrench and at the same time, pull the Spindle Lock Lever until it engages.
8. Tighten arbor nut in a clockwise direction. DO NOT overtighten.
9. Lower the saw blade completely and replace Table Insert.
10. Once the saw blade is secured, adjust the Riving Knife and install Anti­kickback Pawls and Blade Guard.
Installing Anti-Kickback Pawls
Note: Anti-kickback pawls should only be installed for through cuts.
WARNING! Make sure that the pawls are reinstalled immediately after finishing any non-through cut operations which require their removal.
WARNING! Replace dull or damaged anti-kickback pawls. Dull or damaged anti-kickback pawls may not stop a kickback, increasing the risk of serious personal injury.
1. Unplug the saw.
2. Set the blade angle to 0°. Raise the saw blade to maximum height by turning Height Adjustment Knob clockwise. Lock the blade by turning Bevel Lock Handle clockwise.
3. Place Riving Knife in its highest position.
4. Remove pawls from the storage compartment by pulling out and holding knob, then pushing pawls down.
WARNING! TO PREVENT SERIOUS INJURY: Use extra caution when cutting wood with slippery surface as the anti-kickback pawls may not always be effective.
Installing the Blade Guard
WARNING! KEEP GUARD IN PLACE and in good working order for all through cut operations. Reinstall blade guard immediately after finishing any non-through cut operations which require removal of the blade guard. Failure to heed this instruction could result in serious personal injury.
1. Unplug the saw.
2. Hold the knobs (one on either side of the blade guard) and push knobs forward to the front of the Blade guard.
3. Push up until the pin comes out from the slot in the mounting bracket (blade guard storage) at bottom right side of the saw, then remove Blade Guard.
Blade Guard
Storage
Blade Guard
Knob
4. Hold and push knobs forward to the front of the Blade Guard. Place the blade guard pin into the slot indicated on Riving Knife. Pull blade guard fully back onto knife. Push pin and release it to lock guard into position.
Anti-kickback Pawls
5. Secure pawls by placing over Riving Knife until they snap securely into the Mounting Hole.
Knob
Pin
Slot
Note: Pull up on Pawls assembly to make
sure it is secured to Riving Knife.
Anti-kickback
Pawls
Mounting Hole
Riving Knife
Blade Guard
Knob
Pin
5. If blade guard is not parallel to working table when Riving Knife is in uppermost position (through cuts), adjust the set screw as necessary.
WARNING! TO PREVENT SERIOUS INJURY: After the installation, check the blade guard to ensure that it is properly placed and working before operation of the saw.
Riving Knife
Knob
Slot
Page 11For technical questions, please call 1-888-866-5797.Item 57673
Page 12
Installing the Miter Gauge
Note: The Miter Gauge can be installed in either miter gauge groove on either side of blade.
Slide the Miter Gauge into one of the guide grooves.
Miter Gauge
Groove
Miter Gauge
Installing the Rip Fence
Note: The Rip Fence can be installed on either side of blade.
1. Raise Rip Fence Lock Levers on each side of the Rip Fence.
Note: There are three Screws located on both the Front & Rear Rails. The Screws will be used to attach Rip Fence to rails.
2. Align the slot on Rip Fence with the corresponding screw.
3. Place Rip Fence on the rail so that the slot latches onto screw and secure Fence to Rails by pushing Fence Lock Levers down.
OPERATION
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY: Read the miter saw manufacturer’s instruction manual before use. Ensure that the miter saw is firmly secured to the stand. Use as a miter saw stand only – do not use with any other type of power tool. Do not exceed listed weight capacity. Do not use on uneven or slippery surfaces.
Changing Blade Depth
Note: Blade depth should be set so that outer points of blade are higher than workpiece by
approximately 1/8″ to 1/4″ and bottom of gullets
are below top surface of workpiece.
1. Turn Bevel Lock Handle clockwise to tighten it securely.
2. Raise blade by turning Height Adjustment Knob on the height/bevel adjusting handwheel clockwise. Lower blade by turning height knob counterclockwise. Make sure blade is at proper height.
Rip Fence
Table
Slot
Screw
WARNING! Make sure Rip Fence is
perfectly parallel to the blade and completely locked in place to prevent kickback.
WARNING! TO PREVENT SERIOUS INJURY: Do not use Rip Fence when cutting
across wood grain (crosscutting).
Front
Rail
Fence Lock
Lever
Fence Lock
Lever
Dust Collection System
The dust extraction port is located on the back of the table saw. This port can be connected directly to a dust collection system by connecting the pick up end of the dust collection hose to the dust port.
Rear
Rail
Bevel Lock
Handle
Height Adjustment Knob
WARNING! Make sure the blade guard is in place
after adjusting the blade depth. Failure to heed this instruction could result in serious personal injury.
Changing Blade Angle
Note: A 90° cut has a 0° bevel and a 45° cut has a 45° bevel.
1. Loosen the bevel lock handle counter-clockwise.
2. Adjust bevel angle by first pushing Height/ bevel Handwheel all the way to the left.
3. Hold handwheel and slide bevel indicator to the right to increase angle of blade (bringing blade closer to 45° from the tabletop).
4. Hold handwheel and slide bevel indicator to the left to decreases the angle (bringing blade closer to 90° from the tabletop).
Page 12 For technical questions, please call 1-888-866-5797. Item 57673
Page 13
2. For work on a narrow workpiece, secure Extension Table to Rip Fence in the higher position. See below.
Rip Fence
Bevel Lock Handle
Height / Bevel
Adjustment Handwheel
5. Make sure blade is at desired angle. Tighten Bevel Lock Handle clockwise.
Rip Fence Operation
Rail Lock Lever
Note: The Rail Lock Lever allows the customer to adjust the Rip Fence position by moving the Rail itself.
1. To lock the Rail Lock Lever, push lever up and towards the front of the Saw.
2. To unlock, push lever down and towards the back end of the Saw.
High
Position
Extension
Table
Adjusting Knob
Note: The Adjusting Knob allows the customer to make precise adjustments when setting the Rip Fence.
1. Unlock the Rail Lock Lever.
2. Slide Rip Fence close to the desired position.
3. Slowly turn the Adjusting Knob to fix the Rip Fence to desired position. Turn the Adjusting Knob clockwise to move Fence Rail to the right. Turn the Adjusting Knob counter-clockwise to move Fence Rail to the left.
Rip Fence
Rail Lock Lever
Extension Table
Note: The Extension Table can be used to support a workpiece that extends in size beyond the working table, or for a very narrow workpiece.
1. To support a workpiece that extends beyond the working table, secure Extension Table to Rip Fence in the lower position. See below.
Rip Fence
Low
Position
Extension
Table
Adjusting
Knob
4. Lock the Rail Lock Lever.
Rail Lock
Lever
Changing Miter Angle
Note: The miter gauge provides accuracy in angle cuts. For very close tolerances, test cuts are recommended. When making a 90° cross cut, use either miter gauge groove. When making a beveled cross cut (blade tilted in relation to working table) miter gauge should be located in groove on right so that blade is tilted away from the miter gauge and hands.
1. Loosen Lock Knob by turning counterclockwise.
2. With Miter Gauge in the miter gauge groove, rotate gauge until desired angle on scale is reached.
Page 13For technical questions, please call 1-888-866-5797.Item 57673
Page 14
Miter Gauge
Lock Knob
3. Tighten Lock Knob by turning it clockwise.
3. When ripping, always use the Rip Fence. This improves the accuracy of the cut, and reduces the chance for saw blade binding.
Crosscuts/Miter Cuts
Miter
Gauge
Blade Guard
Saw Blade
Cut Line
Workpiece
Scrap Wood
Clamp
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well lit. The work area must not allow access by children or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working.
3. Secure loose workpieces using a vise or clamps (not included) to prevent movement while working.
4. There must not be objects, such as utility lines, nearby that will present a hazard while working.
5. Cut only the following materials:
dimensional lumber, plywood, particle board.
General Operating Instructions
Placement of Hands during Cutting Process
1. Review safety warnings at the beginning of the manual before performing any cutting procedure. Keep all guards in place and in working order.
2. Do not pass hands directly over the saw blade when cutting the workpiece. Push the workpiece into the saw blade using a push stick, push block or by holding the workpiece against the miter gauge.
WARNING! SAFE CUTTING PROCEDURES VARY DEPENDING ON THE TYPE OF CUT. TO PREVENT SERIOUS INJURY FROM KICKBACK:
Use Rip Fence for every Rip Cut (cut along with the grain).
BUT
Do not use Fence for any crosscut (cut against the grain).
Rip Cuts
1. Rip cuts are straight cuts made parallel to (along with) the grain of the wood by sliding the workpiece along the fence.
2. For workpieces wider than 6″ hold the workpiece, staying clear of the saw blade. For workpieces
2″ and 6″, use the included push stick or
make a push stick as described in the safety section of this manual. Use a push block (not
included) when ripping widths under 2″.
1. Adjust the miter gauge to the needed angle and place it in the left or right miter gauge groove on the working table.
2. Hold the workpiece against the miter gauge, and slide them together to make the cut. Clamp smaller workpieces to a piece of scrap wood that can reach beyond the miter gauge and hold the scrap against the gauge while making the cut. Keep the clamp clear of the saw blade.
Making a Cut
1. After adjusting the width and/or angle of the cut, make sure that the Trigger is in the off-position and plug the Table Saw into a grounded 120V outlet.
2. Insert the Switch Key and turn the Switch on.
WARNING! Avoid bevel ripping on bevelling side of the saw blade.
WARNING! TO PREVENT SERIOUS INJURY: The tool will restart automatically if stalled.
3. At the start of the cut, the left hand holds the workpiece firmly on the Work Table (and against the Fence, if used), and the right hand, with the aid of a Push-stick, pushes the workpiece toward the turning Saw Blade. Keep both hands out of the path of the Saw Blade.
WARNING! TO PREVENT SERIOUS INJURY: Throughout the cut, keep all body parts a safe distance from the spinning Blade.
4. After the cut is under way, use the Push Stick to continue guiding the workpiece forward. Just before the cut is completed, move the left hand safely farther away from the workpiece and the Saw Blade. Continue pushing the workpiece into the Saw Blade with the Push Stick until the cut is complete.
5. Once the cut is complete, continue to maintain control of the workpiece. Turn the Switch off. Then, wait until the Saw Blade completely stops rotating before removing the workpiece.
6. To prevent accidents, turn off the Table Saw, remove the key and disconnect its power supply after use. Clean, then store the Saw indoors out of children’s reach.
Page 14 For technical questions, please call 1-888-866-5797. Item 57673
Page 15
MAINTENANCE AND SERVICING
Cleaning, Maintenance,
and Lubrication
Procedures not specifically explained
in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
1. BEFORE EACH USE, inspect the general condition of the tool. Check for:
• loose hardware
• misalignment or binding of moving parts
• cracked or broken parts
• damaged electrical wiring
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces of the tool with clean cloth.
3. WARNING! TO PREVENT SERIOUS
INJURY: If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 15For technical questions, please call 1-888-866-5797.Item 57673
Page 16
PARTS LIST AND DIAGRAM
Parts List
Part Description Qty
1 Cross Head Tapping Screw 9 2 Emergency Stop Panel 1 3 Pin 1 4 Screw 1 5 Handle 1 6 Flat Washer 29 7 Wheel 1 8 Locknut 1 9 Pan Head Screw 3
10 Bevel Scale Label 1
11 Saddle Shape Washer 1 12 Lock Rod 1 13 Lock Handle 1 14 Big Flat Washer 3 15 Lock Washer 1 16 Pan Head Screw 9 17 Flat Washer 6 18 Angle Pointer 1 19 Front Panel 1 20 Big Flat Washer 9 21 Cross Head Tapping Screw 25 22 HS Bolt 2 23 Reinforced Panel 1 24 Eccentric Limit Block 2 25 HS Bolt 20 26 Spring Washer 24 27 Switch Box 1 28 Cord Clamp 1 29 Front-Left Foot,A 2 30 Main Frame 1 31 Front-Left Foot,B 2 32 Cross Head Tapping Screw 12 33 Back-Left Foot,A 2 34 Back-Left Foot,B 2 35 HS Bolt 8 36 Spring Washer 12 37 Flat Washer 14 38 Pad 4 39 Hex Bolt 1 40 Storage Clip Plate 1 41 Push Stick 1 42 Wing Nut 1 43 Wrench 1 44 Hex Thin Nut 4 45 Right Panel 1 46 Low Blade Guard Cover 1 47 Protection Plate 1
Part Description Qty
48 Bracket 2 49 Hex Thin Nut 1 50 Out Flange 1 51 Saw Blade 1 52 Bolt 1 53 Eccentric Handle 1 54 Cam Plate 1 55 Riving Knife 1 56 Spring 1 57 Paw 1 58 Washer 2 59 Ring 2 60 Pin Knob 1 61 HS Bolt 1 62 Plate 3 63 Limit Plate,B 1 64 Table Lock Spring 1 65 Elastic Pin 1 66 Lock Rod 1 67 Longer Nut,M8,B 1 68 Flat Washer 1 69 Bolt 1 70 Lock Handle 1 71 Lock Block A 2 72 Limit Plate A 1 73 Locknut 3 74 Washer 2 75 Table Locking Rod A 1 76 Longer Nut,M8 1 77 Lock Rod B,Assembly 1 78 Lock Link 2 79 Lock Rod C,Assembly 1 80 Bracket 1 81 Pin 1 82 Anti-Kick Back Palte Left 1 83 Spring 1 84 Pin 1 85 H.s.bolt 4 86 Adjusting Bracket,C 2 87 Adjusting Bracket 2 88 Spring 2 89 Pin 2 90 Rod 1 91 Gear 2 92 Nut 2 93 HS Bolt 4 94 Bracket A 2
Page 16 For technical questions, please call 1-888-866-5797. Item 57673
Page 17
Parts List (cont’d)
Part Description Qty
95 Ring 2 96 Knob 1 97 Flat Washer 1 98 HS Bolt 10 99 Fix Rail A 2
100 Friction Rule A 2 101 Fixed Seat 2 102 Sliding Plate 2 103 Cross Head Screw 2 104 Carry Handle 2 105 Back Rail 1 106 Nut 6 107 Big Flat Washer 6 108 Bolt 6 109 Fix Rail B 2 110 Friction Rule B 2
111 Working Table 1 112 Lock Plate 1 113 Table Insert 1 114 Protection Plate A 1 115 Protection Plate B 1 116 Bolt 6 117 Spring 2 118 Clip 2 119 Right Guard 1 120 Guard Bolt 4 121 Pin Cap 2 122 Ring 2 123 Pin 1 124 Limit Pin 1 125 Support Bracket 1 126 Left Guard 1 127 Pin 2 128 Handle 2 129 Screw 2 130 Washer 8 131 Cross Head Tapping Screw 6 132 Side Fence Cover B 1 133 Sid Fence Cover A 2 134 Pin 2 135 Fence Rear Cover 1 136 Position Clip 2 137 Position Plate 2 138 Fence 1 139 Fence Front Cover 1 140 Side Fence Cover C 1 141 Lock Plate 2 142 Fence Clip B 1
Part Description Qty
143 Fence Clip A 1 144 Side Fence 1 145 Miter Gauge Lock Handle 1 146 Miter Gauge 1 147 Lock A 1 148 Pointer 1 149 Sliding Bar 1 150 Front Rail 1 151 Pointer 1 152 Cap 1 153 Spindle Lock Plate 1 154 Main Body 1 155 Cover 1 156 Guide Pillar 2 157 Cross Head Screw 4 158 Cross Head Screw 2 159 Ball 8 1 160 Spring 1 161 Pin 6 2 162 Bolt 1 163 Spring 1 164 Sleeve 1 165 Motor 1 166 Ascent Adjusting Rod B 1 167 Key 2 168 Ascent Adjusting Bracket 1 169 Bevel Gear Wheel 2 170 Protection Plate 1 171 Adjusting Rod 1 172 Retaining Ring 2 173 Protection Plate 1 174 Screw B 2 175 Spring 1 176 Inner Flange 1 177 Miter Gauge Storage 178 Left Panel 179 Cord Sleeve 1 180 Cord & Plug 1 181 Switch 1 182 Switch Fix Bracket 1 183 Switch Lock 1 184 Cord Clamp 1 185 Spring 1 186 Lock Block A 1 187 Scale Label 1 188 Teeth Washer 1 189 Screw 1
Page 17For technical questions, please call 1-888-866-5797.Item 57673
Page 18
Assembly Diagram
21-12
1
12
130-8
137-1
136-1
133-1
135
131-1
129-1
149
21-5
26-1 25-1 21-8
21-7
6-28
21-6
127-1
87-1 86-1
6-16 26-13 85-1
84
154
24-2
132
24-1
21-13
83
59-2
20-7
103-2
58-2
29-1
98-298-3
27
130-1
184
1- 8 1- 9
21-18
37-6 36-6
28
128-1
134-1
141-2
104-2
99-1
98-1
94-2
6-17 26-14
73-2 85-2 88-1
81
82
153
152
174-2
175
174-1
6-26 25-19
26-23 25-20 26-24
6-27
38-3
37-5
36-5
1- 5
35-5
35-6
1- 6
1- 7
30
142 17-4 21-20
158-1
6-24
18
21-24
130-6 131-5
22-2
22-1
107-7
16-7
148
20-8
21-1
145
146
109-2
158-2 172-1 169-2
130-7
21-22
131-6
17-6
189
110-2
98-5
98-4
96
91-2
97
155156-1
173
25-6
21-19 6- 3
6- 2
26-2 25-2
23
143
17-5
21-21
92-2
157-1
26-17
6-20
160 159
6-25
26-22
6-29
25-5
21-3
20-3
21-2
20-2
20-1
19
188
137-2
136-2
139
133-2
140
131-2
21-14
130-2
29-2
8-2
141-1
134-2
21-15
166
167-1 168
169-1 172-2
1- 1 1- 2
2
4
9- 2
13
130-3
1- 3
1- 4
21-25
130-5
130-4
131-4
127-2 131-3
41
108-4
17-2
16-8
151
16-9 17-3
164
162
163
73-3
165
170
6-23
26-20
9- 3
157-3
180
181
182
183
3
7
6- 1
5
10
11
12
15
14-1
138
144
187
150
106-4107-4
106-5
107-5
108-5
108-6 107-6 106-6
6-21
156-2 26-18 157-2
161-1
161-2
26-19
9- 2
6-22
26-21 157-4 171
167-2
179
178
21-4
20-4
8- 1
9- 1
16-1
17-1
120-4
126
120-3
118-2
116-2
115
31-1
6- 9 6- 8
58-1
33-1
101-1
26-10
59-1
57
54
37-9 36-9 93-4
60
38-2
37-4 36-4
32-3
32-1 32-2
32-4
53
90
34-1
52
78-279
62
25-11 25-12 25-13 25-14
32-6
21-23
26-8
116-3
112
16-6
147
102-1 37-10 36-10 93-4
186
185
20-9
78-1
6- 6
26-7
21-16
21-17
37-8 36-8 35-8 36-7
37-3 36-3
35-3 35 -4
32-5
32-7
6-10 26-6 25-15
116-4
100-1 14-3
95-2
89-1
74-2
61-1
80
26-9
56
55
176
177
121-2
111
103-1
6- 7
32-8
77
6-11 26-5 25-16
38-4
35-7
32-9
110-1
64
51
37-7
33-2
34-2
122-2
61-2
44-4
37-14
63
113
14-2 95-1
65
50
32-11
116-6
117-2
26-15
66
49
32-10
116-5
116-1
109-1
89-2 6-18
85-3 44-376
44-2
114
104-1
102-2
26-12 25-17
67
37-2 36-2 35-2 35-1
32-12
117-1
94-1
6-15
68
38-1
31-2
125
124
118-1
37-11 36-11
93-2
88-2
69
123
98-10
70
21-9
37-13
71-1 71-2
6-12 26-3
25-10
37-1
36-1
87-2 86-2 6-19 26-16 85-4
25-18
39
40
21-10
122-1
61-3 6-14 26-11
48-2 25-8
121-1
120-2
120-1
119
106-3
107-3
108-3
108-2
107-2
98-8
21-11
46
20-6
16-3
16-4
98-7
48-1
25-7
6- 5
106-2
106-1
107-1
105
98-6
47
16-5
45
44-1
25-4
108-1
42
43
20-5
29-1
100-2
101-2 37-12 36-12 93-1
75 74-1 73-1
72
25-3
92-1 91-1
6-13 26-4 25-9
98-9
99-2
16-2
6- 4
Page 18 For technical questions, please call 1-888-866-5797. Item 57673
Page 19
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Page 19For technical questions, please call 1-888-866-5797.Item 57673
Page 20
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
For technical questions, please call 1-888-866-5797
Copyright© 2020 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn
proportionally. Due to continuing improvements, actual product may differ slightly from the
product described herein. Tools required for assembly and service may not be included.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Loading...