Henley Hampton 21kW, Hampton 30kW, Cambridge 5kW, Cambridge 7.5kW, Cambridge 10.5kW Installation And Operating Instructions Manual

1 | www.henleystoves.com

Important: – This product must be installed by a suitably qualied installer.

PLEASE READ ALL THESE INSTRUCTIONS CAREFULLY!

For safety reasons it is essential that your stove is correctly installed and operated. Henley Stoves cannot

accept responsibility for any fault or consequential problems arising through incorrect installation or operation.

Please hand these instructions to the stove user when the
installation is complete.
Leave the stove ready for operation and instruct the user in
the correct use of the appliance and operation of controls.

Henley Hampton 21kW / 30kW

Boiler / Room Heater Stove Installation and Operating Instructions

Henley Stoves, Curraheen, Tralee, Co. Kerry | www.henleystoves.com

2 | www.henleystoves.com

Table of contents

Technical Specication

Stove Commissioning Checklist

Installation Instructions
Hearth
Ventilation
Chimney
Flue outlet positions

User instructions
Connecting a chimney to a ue
Combustible Materials
Air Controls
Door handle
Recommended Fuels
Lighting the Stove
Re-fuelling
Shutting Down

Maintenance
Chimney Sweeping
Replacing the Fire Rope around your stove door
Removing the Ash
Removing the fuel retainer
Replacing the glass in your stove door
Replacing the bae plate in your stove
Stove Finish (paint)
Warranty
Chimney Fire and Over Firing
Seasonal Use

Frequently Asked Questions

Parts

Servicing

Warranty Registration Form

DEFRA

3

4

5
5
5
6

7
8
8
9
9
9
9
10

10
10
10
11
11
11
12
12
12
12

13

14

14

15

16

Congratulations on your purchase of your Henley Druid Stove. With the proper care and attention your Henley stove will
give you a lifetime of heat, comfort and pleasure. This manual contains instructions on how to install and maintain your
Henley Stove. For both your comfort and safety please take the time to read through it carefully.

Safety
A reguard conforming to BS 8423:2010 should be used in the presence of children, the old or inrm.
Please note, this appliance should be used with the re door closed at all times except when fuelling, de-ashing or initial lighting.
Do not use aerosol sprays or any other ammable materials near the appliance under re. Fire cement is caustic, hand and eye protection should always
be worn, prolonged contact with the skin should be avoided. Henley Stoves will not be responsible for any consequential or incidental loss or injury how­ever caused. Before continuing any further with theinstallation of this appliance please read the following guide to manual handling.

• Always obtain assistance when lifting the appliance

• When lifting always keep your back straight, bend your legs not your back

• Avoid twisting at the waist. It is better to reposition your feet.

• Avoid upper body/top heavy bending. Do not lean forwards or sideways when handling the re

• Always grip with the palms of your hands do not use your ngertips for support, use gloves for a better grip

• Always keep the stove close to the body as this will minimise the cantilever action.

Fire Cement
Some types of re cement are caustic and should not be allowed to come into contact with the skin. In case of skin contact, wash
immediately with plenty of water.

Asbestos
This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the course of installation then please seek specialist guidance and use
appropriate protective equipment.

3 | www.henleystoves.com

Technical Specication

All sizes in MM

Model Size A Size B Size C Size D
Hampton 21kw
Hampton 30kw

Size B

Size D

Size C

Size A

Diagram shows a Hampton 30kw. Corresponding sizes for both Hampton 21kw and 30kw can be found below:

Hampton 21kw

Wood
Nominal heat output kW 21.0
kW Output to Water 15.0
kW Output to Room 6.0

Hampton 30kw

Wood
Nominal heat output kW 30.0
kW Output to Water 23.0
kW Output to Room 7.0

Results of independent testing to EN 13240

Results of independent testing to EN 13240

***Safe distances to combustible materials should

be 750 mm to the rear and 450 to the side

***Safe distances to combustible materials should

be 800 mm to the rear and 500 to side

***All sizes are correct at time of publish but are subject to change without prior notice. Please

ensure you confrim all measurements before commencing any installation works.

4 | www.henleystoves.com

Stove Commissioning Checklist

Please complete the form below as it will be of great assistance in the unlikely event that there is a problem
with the stove or a warranty claim needs to be made. Please contact the installer or dealer if there is a problem.

Dealer appliance was purchased from

Essential Information - MUST be completed

Installation Engineer

Commissioning Checks (to be completed and signed)

..........................................................................................................................................

..........................................................................................................................................

........................................................................................................................................................

..........................................................................................................................................

............................................................................................................................

............................................................................................................................

............................................................................................................................

Name:

Address:

Phone:

Date installed:

Model Description:

Serial number:

............................................................................................................................

............................................................................................................................

............................................................................................................................

Company name:

Address:

Phone:

Stove correctly ued according to building regulations

Flue swept and integrity of ue veried

Smoke test completed on installed stove

Spillage test completed

Use of appliance and operation of controls explained to end-user

Check that specied clearance to combustibles has been adhered to

Instruction manual handed to end-user

HETAS Approved (Please tick relevant box): Yes No

If Yes, please include certicate of compliance.

Yes No

Yes No

Yes No

Yes No

Yes No

Yes No

Yes No

.............................

....................................................

..................................................

..............................................................................

................

............

.......................................................

Signature:

.......................................................

Print name:

........................................................

5 | www.henleystoves.com

Installation Instructions

1. Before installation and/or use of this appliance please read these instructions carefully to ensure that all requirements
are fully understood. The appliance must be tted by a registered installer*, or approved by your local building control
ocer.

2. All local regulations, including those referring to national and european standards need to be complied with when
installing the appliance. In all cases the installation must comply with current local regulations including Building Regula­tions, Local Authority Byelaws and other specications or regulations including Ireland, UK or EU standards referred to as
they aect the installation of the stove. Please refer to
Building regulations available on http://www.environ.ie and http://www.planningportal.gov.uk.

3. Only use for domestic heating in accordance with these operating instructions.

4. Only approved fuels must be burned. Do not use with liquid fuels or as an incinerator.

5. Appliance surfaces become very hot when in use. Use a suitable reguard if young children, elderly or inrm persons are
present.

6. Do not place photographs, TV’s, paintings, porcelain or other combustible items on the wall or near the appliance. Expo­sure to hot temperatures will cause damage. Do not place furniture, or other items such as drying clothing, closer than 1m
from the front of this appliance.

7. Extractor fans or cooker hoods must not be placed in the same room or space as this can cause the appliance to emit
fumes into the room.

Constructional Hearth

Decorative Hearth

150mm

Minimum

12mm

150mm Min

150mm Min

225mm Minimum

500mm Minimum

Change in level to

mark safe perimeter

840mm Minimum

840mm Minimum

125mm

Appliance

Hearth
The appliance must stand on a non-combustible constructional
hearth which is at least 125mm thick. The building must have
a suitable load-bearing capacity for the hearth and appliance.
Consult a structural engineer for advice before proceeding. When
tting into an existing hearth check that the hearth complies with
current construction regulations and is at least the minimum sizes
shown. If there is no existing replace or chimney it is possible
to construct a suitable non-combustible housing and hearth set­ting. The ue must be installed in accordance with all local and
national regulations and current rules in force. Check if adding a
new chimney to your property requires planning permission. The
hearth must protrude at least 250mm in front of the stove and
150mm each side. If the hearth is constructed on timber, there
must be a clearance of at least 250mm from the timber to the top
surface of the hearth.

Ventilation
This appliance requires a constant supply of air to maintain proper combustion and eective ue performance. An inadequate air
supply can result in poor combustion and smoke entering the room which is potentially dangerous. This supply of air can come
from either:

• The natural leakage of air into the room in which the product is tted.

• Purpose provided ventilation.

The amount of air required must comply with local building regulations and the rules in force. If spillage is detected during com­missioning then there may be insucient natural ventilation and an additional air supply will be necessary. Many older buildings
are suciently ventilated by natural leakage of air to provide suitable air supply for an appliance of 5kW output or less.
Extractor fans should not be installed in the same room as the appliance and any air vents should be positioned so that they are
not liable to blockage.

Chimney
The chimney draw is critical on any installation and should be checked to ensure that it matches what is specied. If it is higher
than
recommended provision must be made to correct the overdraw. The draw can vary in dierent weather conditions and the
customer should be made aware of this. Failure to correct an over-drawing ue will invalidate the warranty, and may damage the
appliance.
Please remember that chimney draught is dependent on four main factors.

• Flue gas temperature • Flue height • Flue size • Flue terminal

The ue or chimney system must be in good condition. It must be inspected by a competent person and passed for use with the
appliance before installation. Products of combustion entering the room can cause serious health risks.

The following must be checked:

• The construction of the masonry chimneys, ue block chimneys and connecting ue pipe system must meet the requirements

of the Building Regulations.

• A exible ue liner system can be used if certied for use with solid fuel systems and installation complies with manufacturer’s

instructions and Building Regulations. The ue liner must be replaced when an appliance is replaced, unless proven to be recently
installed and in good condition.