Hello Kitty KT2015 Owner's Manual

2.4 GHz DIGITAL CORDLESS PHONE

OWNER’S MANUAL

KT2015

SUBSCRIPTION TO CALLER ID SERVICE FROM YOUR LOCAL TELEPHONE COMPANY

IS REQUIRED FOR ALL CALLER ID FEATURES TO OPERATE CORRECTLY

PLEASE READ AND FOLLOW THIS MANUAL BEFORE USING YOUR

TELEPHONE AND KEEP IT FOR FUTURE REFERENCE

1

IMPORTANT SAFETY INSTRUCTIONS

This symbol is to alert you the important
operating or servicing instructions that may
appear in your owner’s manual. Always follow
basic safety precautions when using this product
to reduce the risk of injury, fire or electric shock.

When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire or electric shock and injury to persons including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool.

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing
serious damage to the product.

6. Slots and openings in the enclosure and the back or bottom are provided for ventilation to
prevent overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
This product should never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper ventilation is provided.

7. This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your
dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product where the cord
will be abused by persons walking on it.

9. Do not overload wall outlets and extension cords as this can result in the risk of fire or
electric shock.

10. Never push objects of any kind into this product through enclosure slots as they may touch
voltage points or short out parts that could result in a risk of fire or electric shock. Never
spill liquid of any kind on the product.

11. Do not disassemble this product. Take it to a qualified service technician or service center
when repair work is required. Opening or removing covers may expose you to voltage or
other risks. Incorrect reassembly can cause electric shock when the appliance is
subsequently used.

12. Unplug this product from the wall outlet and refer to qualified service personnel under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust

only those controls that are covered by the operating instructions. Improper adjustment
of other controls may result in damage and may require extensive work by a qualified

technician to restore the product to normal operation.
E. If the product has been dropped or the enclosure has been damaged.
F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone during an electrical storm. There may be a remote risk of electric
shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of a leak.

15. Never install telephone wiring during a lightning storm.

-1-

2

16. Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.

17. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.

18. Use caution when installing or modifying telephone lines.

19. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries
in a fire. They may explode. Check with local codes for possible special disposal
instructions.

SAVE THIS INSTRUCTIONS

FCC INFORMATION

This equipment complies with Part 68 of the FCC Rules. The label affixed to this equipment
contains, among other information, the FCC Registration Number and Ringer Equivalence
Number (REN) for this equipment. We suggest that you review the following information
provided by the FCC.

NOTIFICATION TO THE TELEPHONE COMPANY

Notification to the telephone company is no longer required prior connecting the registered
equipment. However, upon request from the telephone company the user shall tell the
telephone company which line the equipment is connected to as well as the registration number
and the ringer equivalence of the registered protective circuitry. In most, but not all areas, the
sum of all REN’s should be 5.0 or less.

MALFUNCTION OF THE EQUIPMENT

If the device is not operating properly, the user should immediately disconnect it from the
telephone line as it may cause harm to the telephone network. In the event service is needed
the user should contact:
Service Department
Spectra Merchandising International, Inc.,
Chicago Industry Tech Park
4230 North Normandy Avenue,
Chicago, IL 60634, U.S.A.
Tel: [phone] or call toll-free hotline [phone]

TELEPHONE CONNECTION REQUIREMENTS

Except for ringers provided by telephone company, all connections to the telephone network
except for made through standard plugs telephone company provided jacks, or equivalent, in
such a manner as to allow for easy and immediate disconnection of the terminal equipment.
Standard jacks should be so arranged that, if the connected plug is withdrawn, no interference
to the operation of the equipment at the customer’s premises which remains connected to the
telephone network shall occur by reason of such withdrawal.

INCIDENCE OF HARM

Should terminal equipment or protective circuitry cause harm to the telephone network, the
telephone company shall, where practical, notify the customer that temporary discontinuance of
service may be required. However, where prior notices are not practical, the telephone
company may temporarily discontinue service if such action is deemed reasonable in the

3

circumstances. In the case of such temporary discontinuance, the telephone company shall
promptly notify the customer who has the right to bring a complaint to the FCC if he feels the
disconnection is not warranted.

Interference Information -- USA

 This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference; and (2) This device must accept
any interference received, including interference that may cause undesired operation.

 This equipment has been tested and found to company with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.

 This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.

 If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user encouraged to try to correct the
interference by one or more of the following measures:

 Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is

“receiving” the interference).

 Reorient or relocate and increase the separation between the telecommunications equipment

and receiving antenna.

 Connect the telecommunications equipment into an outlet on a circuit different from that to

which the receiving antenna is connected.

 If these measures do not eliminate the interference, please consult your dealer or an

experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and Resolve
Radio/TV Interference Problem”. This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering
copies.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.

WARNING: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.
Privacy of communications may not be ensured when using this phone.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. For body
worn operation, this phone has been tested and meets the FCC RF exposure guidelines
when used with the belt clip supplied or designated for this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the

4

user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES

The telephone company may make changes in its communications facilities, equipment,
operations or procedures, where such action is reasonably required and proper in its business.
Should any such changes render the customer’s terminal equipment incompatible with the
telephone company facilities, the customer shall be given adequate notice to make
modifications to maintain uninterrupted service.

General

The FCC prohibits customer-provided terminal equipment to be connected to party lines or to
be used in conjunction with a coin telephone service.

Installation

This device is equipped with a USOC RJ11C standard miniature modular jack and is designed
to plug directly into a modular jack.

***THIS TELEPHONE HAS BEEN CERTIFIED AS HEARING AID COMPATIBLE ***

5

BATTERY CAUTIONARY INSTRUCTIONS

CAUTION – To Reduce the Risk of Fire or injury to Persons, Read and Follow these

instructions.

1. Risk of explosion if battery is replaced by an incorrect type.

2. Use only the supplied rechargeable battery pack: LEXEL, LH070-3A44C2BRML1P

Ni-MH AAA 700mAh 2.4V Battery Pack.

3. Do not dispose of the batteries in fire. The cell may explode. Check with local codes for

possible special disposal instructions.

4. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause

damage to the eyes and skin. It may be toxic if swallowed.

5. Exercise care in handling batteries in order not to short the batteries with conductor

material such as rings, bracelets, and keys. The battery or conductor may overheat and

cause burns.

6. Do not attempt to recharge the batteries provided with or identified for use with this

product by heating them. The batteries may leak corrosive electrolyte or explode.

7. Do not attempt to rejuvenate the battery provided with or identified for use with this

product by heating them. Sudden release of the battery electrolyte may cause burns or

irritation to eyes or skin.

8. All batteries should be replaced at the same time. Mixing fresh and discharged batteries

could increase internal cell pressure and rupture the discharged batteries.

9. When inserting batteries into this product, the proper polarity or direction must be

observed. Reverse insertion of batteries can cause charging, which may result in

leakage and explosion.

10. Remove the batteries from this product if it will not be used for a long period of time

(several months or more) since during this time the batteries could leak, damaging in the

product.

11. Discard “dead” batteries as soon as possible since “dead” batteries are more likely to

leak in a product.

12. Do not store this product, or the batteries provided with or identified for use with this

product in high-temperature areas. Batteries that are stored in a freezer or refrigerator for

the purpose of extending shelf life should be protected from condensation during the

storage and defrosting. Batteries should be stabilized at room temperature prior to use

after storage.

SAVE THESE INSTRUCTIONS

6

INTRODUCTION TO CALLER ID INSTRUCTIONS

Read this manual carefully before using this product and keep it for future reference.

Congratulations on your purchase of this product! The unit allows you to take advantage of the
Caller Identification service that may be offered by your local telephone company. Not all local
telephone companies provide Caller Identification service therefore you must make sure the
service is available.

IMPORTANT: For your Caller ID to function, you must first contact your local telephone
company to arrange to have Caller ID with Call Waiting service installed on your line.
There will be an extra charge added to your monthly telephone bill for this service.
Please consult with your local telephone company for the Caller ID service charge.

1. The Caller ID function can be used to screen unwanted calls, eliminate harassment from

annoying calls, or to return missed calls using the displayed speed dial feature.

2. When used with Caller ID service, the unit displays the name or the telephone number of the

person calling before you pick up your telephone.

3. Additionally, if you subscribe to Call Waiting combined with Caller ID service, this phone lets

you see who’s calling while you’re on another call (your telephone company must provide the

service needed for this feature to work).

FUNCTIONS AND CONTROLS

Handset Section

New Message LED

MENU / ▼ Menu / down key

/ ▲

CID / Menu/ Up key

INT / OK INT / OK key

C Cancel Key

Mute key

/ P Redial / Pause key

External call key.

R / Flash /Memory key

* / Asterisk / lock key

# Hash key

7

Base Section

PAGE

Page key

IN USE In-use LED:

The In-use LED will be steadily on during off-hook. During the
period of incoming call, the In-use LED will also follow the ring
cadence to go on or off. When registering, it will flash as a special
cadence.

CHARGING Charging LED

LCD Display Section

Battery icon
Phone icon

EXT External call icon

INT Internal call icon

CID icon

No ring icon
Mute icon

Key lock icon

Aerial icon

▲ Up arrow
▼ Down arrow

8

PHONE INSTALLATION INSTRUCTIONS

1. Never install telephone wiring during a lightning storm.

2. Never install telephone jacks in wet or damp locations.

3. Never touch un-insulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.

4. Use caution when installing or modifying telephone lines.

GETTING STARTED

Connecting the Base Station and Power Plug

Connect one end of the telephone line cord and the AC adaptor to the corresponding sockets in
the base station (they can not be connected incorrectly because the sockets and plugs are
designed prevent reverse poling). Lay the cable under the telephone to the rear. Plug the
telephone line in the telephone connection socket. Insert the power plug at the other end into
the power outlet. The base station in now ready to operate.

Only use the connection

cable supplied.

The base station has no power switch. Ensure that a Mains power outlet is
close by and that the power plug is easy to access. Check that the voltage
specified on the power adaptor corresponds to that supplied by the local
power network.