Helix E10, E40 User Manual

4-Channel Tube Amplifier
GERMANY
BEDIENUNGSANLEITUNG
INSTRUCTION MANUAL
deutsch/english
Digital Mono Amplifier
2
wir gratulieren Ihnen zum Kauf dieser hochwertigen HELIX
ESPRIT-Endstufe. Dieser Verstärker wurde nach neuesten
technischen Erkenntnissen entwickelt und zeichnet sich
durch hervorragende Verarbeitung und überzeugende
Technologie aus. Nach mehr als 27 Jahren Erfahrung in der
Forschung und Entwicklung von Audiokomponenten setzt
er neue Maßstäbe in puncto Preis-Leistungsverhältnis. Das
neue, extravagante HELIX ESPRIT-Design macht ihn zu
einem außergewöhnlichen, klangstarken Verstärker der
Spitzenklasse. Viel Freude an diesem Produkt wünscht
Ihnen das Team von
AUDIOTEC FISCHER
Allgemeines zum Einbau von HELIX-Verstärkern
Um alle Möglichkeiten optimal ausschöpfen zu können, lesen Sie bitte sorgfältig die nachfolgenden Installationshinweise. Wir garantieren, dass jedes Gerät vor Versand auf seinen einwand­freien Zustand überprüft wurde. Vor Beginn der Installation unterbrechen Sie den Minusanschluss der Autobatterie. Wir empfehlen Ihnen, die Installation von einem Einbauspezialisten vornehmen zu lassen, da der Nachweis eines fachgerechten Einbaus und Anschlusses des Gerätes Voraussetzung für die Garantieleistungen sind. Installieren Sie Ihren Verstärker an einer trockenen Stelle im Auto und vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält. Montieren Sie das Gerät nicht in zu klei­ne, abgeschlossene Gehäuse ohne Luftzirkulation oder in der Nähe von wärmeabstrahlenden Teilen oder elektronischen Steuerungen des Fahrzeuges. Im Sinne der Unfallsicherheit muß der Verstärker professionell befestigt werden. Dieses geschieht über die 4 beiliegenden Schrauben, die in eine Montagefläche eingeschraubt werden, die genügend Halt bieten muss. Bevor Sie die Schrauben im Montagefeld befestigen, vergewissern Sie sich, daß keine elektri­schen Kabel und Komponenten, hydraulische Bremsleitungen, der Benzintank etc. dahinter verborgen sind. Diese könnten sonst beschädigt werden. Achten Sie darauf, daß solche Teile sich auch in der doppelten Wandverkleidung verbergen können.
Allgemeines zum Anschluss der Verstärker
Der Verstärker darf nur in Kraftfahrzeuge eingebaut werden, die den 12V-Minuspol an Masse haben. Bei anderen Systemen kön­nen der Verstärker und die elektrische Anlage des Kfz beschädigt werden. Die Plusleitung für die gesamte Anlage sollte in einem Abstand von max. 30 cm von der Batterie mit einer Hauptsicherung abge­sichert werden. Der Wert der Sicherung errechnet sich aus der maximalen Stromaufnahme der Car-Hifi-Anlage. Die Kabelverbindungen müssen so verlegt sein, dass keine Klemm-, Quetsch- oder Bruchgefahr besteht. Bei scharfen Kanten (Blechdurchführungen) müssen alle Kabel gegen Durchscheuern gepolstert sein. Ferner dürfen die Stromversorgungskabel niemals mit Zuleitungen zu Vorrichtungen des Kfz (Lüftermotoren, Brandkontrollmodulen, Benzinleitungen etc.) verlegt werden. Um eine sichere Installation zu gewährleisten, sollte auf hohe Qualität der verwendeten Anschlussmaterialien geachtet werden.
1
3
2
5
4
Anschluss Massekabel Anschluss Remoteleitung Anschluss Batteriekabel Sicherungen 4 x 20 Ampere Power / Status LED Signaleingänge
1 2 3 4 5 6
6
12
11
10
7
8
9
13
AUSSTATTUNG UND BEDIENELEMENTE ESPRIT E10
DEUTSCH
Bass Remote-Anschluss Schalter für Bass Remote Levelregler für Eingangsempfindlichkeit Bass-Equalizer Phasenregler Frequenzeinstellregler für Tiefpass LS-Anschlussklemmen
7 8
9 10 11 12 13
3
1 Anschluss Massekabel
Das Massekabel sollte am zentralen Massepunkt (dieser befindet sich dort wo der Minuspol der Batterie zum Metallchassis des Kfz geerdet ist) oder an einer blanken, von Lack
resten befreiten Stelle
des Kfz-Chassis angeschlossen werden.
2 Anschluss Remoteleitung
Die Remoteleitung wird mit dem automatischen Antennen­anschluss des Steuergerätes (Radio) verbunden. Dieser ist nur aktiviert, wenn das Steuergerät EIN-geschaltet ist. Somit
wird der
Verstärker mit dem Steuergerät ein-und ausgeschaltet.
3 Anschluss Batteriekabel
Das +12V-Versorgungskabel ist am Pluspol der Batterie anzu­schließen. Empfohlener Querschnitt: min. 25 mm2.
4 Sicherungen
Die Eingangssicherungen sind parallel geschaltet und schützen vor einem geräteinternen Fehler, d. h. die Anlage muß mit einer zusätzlichen Sicherung in Nähe der Batterie (max. 30 cm entfernt) abgesichert werden. Die Sicherungswerte betragen 4 x 20 Ampere für die E10.
5 Power / Status LED
Die blaue LED zeigt den Betriebszustand der Endstufe an.
6 Signaleingänge
Die Esprit-Verstärker haben RCA-Anschlüsse zum Kontaktieren von Cinchkabeln, die mit den Vorverstärkerausgängen der Line­Outputs des Steuergerätes oder eines Vorverstärkers verbunden werden. Diese Anschlüsse sind
vergoldet um eine bessere NF-
Übertragung zu gewährleisten.
7 Bass Remote-Anschluss
Mit der Bass Remote Control lässt sich die Basslautstärke vom Fahrersitz aus kontrollieren.
8 Schalter für Bass Remote
Zur Einschaltung der Bass Remote Control.
9 Levelregler für Eingangsempfindlichkeit
Mit Hilfe dieser Regler kann die Eingangsempfindlichkeit der Kanäle an die Ausgangsspannung des angeschlossenen Steuer­gerätes angepasst werden. Diese Regler sind keine Lautstärkeregler, sondern dienen nur der Anpassung. Der Regelbereich ist 300 mV bis 6 V.
10 Bass-Equalizer
Mit Hilfe dieses Reglers kann das Basssignal bei 45 Hz von 0 bis 18 dB angehoben werden.
11 Phasenregler
Mit Hilfe dieses Reglers kann die Phase des Basssignals um bis zu 180 Grad verschoben werden, um so eine optimale Laufzeitanpassung zu den anderen Kanälen zu erreichen.
12 Frequenzeinstellregler für den Tiefpass
Regler zur Einstellung der Trennfrequenz von 40 Hz bis 150 Hz.
13 Lautsprecheranschlussklemmen
Zum Anklemmen der Lautsprecherleitungen.
Verbinden Sie niemals die Lautsprecherleitungen mit der Kfz-Masse (Fahrzeugkarosserie). Dieses kann Ihren Verstär­ker zerstören.
Achten Sie darauf, dass alle Lautsprecher­systeme phasenrichtig angeschlossen sind, d.h. Plus zu Plus und Minus zu Minus. Vertauschen von Plus und Minus hat ei- nen Totalverlust der Basswiedergabe zur Folge. Der Plus­pol ist bei den meisten Lautsprechern gekennzeichnet.
Die Impedanz pro Kanal sollte 2 Ohm nicht unterschrei­ten, da sonst eine zu hohe Wärmeentwicklung den Verstärker
zum Abschalten bringen kann.
TECHNISCHE DATEN ESPRIT E10
Ausgangsleistung pro Kanal an 4 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 350 Watt RMS
Ausgangsleistung pro Kanal an 2 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 550 Watt RMS
Ausgangsleistung pro Kanal an 1 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 700 Watt RMS
Frequenzbereich . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Hz - 150 Hz
Regelbereich Tiefpass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hz - 150 Hz
Klirrfaktor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,1%
Geräuschspannungsabstand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 90 dB
TIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,02%
Dämpfungsfaktor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 150
Eingangsimpedanz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 kOhm
Eingangsempfindlichkeit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 mV - 6 V
Sicherung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 x 20 Ampere
Bass Boost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 18 dB
Abmessungen (H x B x T) in mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 x 395 x 217
Gewicht netto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,5 kg
1
3
2
5
4
Anschluss Massekabel Anschluss Remoteleitung Anschluss Batteriekabel Sicherungen 4 x 15 Ampere Power / Status LED Signaleingänge CH 1 + CH 2 Levelregler für Eingangsempfindlichkeit Schalter für Hochpassfilter Frequenzeinstellregler für Hochpass LS-Anschlussklemmen CH 1 + CH 2
1 2 3 4 5 6 7 8 9
10
6
14
12
11
10
13
7
8
9
15
AUSSTATTUNG UND BEDIENELEMENTE ESPRIT E40
Signaleingänge CH 3 + CH 4 Levelregler für Eingangsempfindlichkeit Schalter für Hochpassfilter Frequenzeinstellregler für Hochpass LS-Anschlussklemmen CH 3 + CH 4
11 12 13 14 15
1 Anschluss Massekabel
Das Massekabel sollte am zentralen Massepunkt (dieser befindet sich dort wo der Minuspol der Batterie zum Metallchassis des Kfz geerdet ist) oder an einer blanken, von Lack
resten befreiten Stelle
des Kfz-Chassis angeschlossen werden.
2 Anschluss Remoteleitung
Die Remoteleitung wird mit dem automatischen Antennen­anschluss des Steuergerätes (Radio) verbunden. Dieser ist nur aktiviert, wenn das Steuergerät EIN-geschaltet ist. Somit
wird der
Verstärker mit dem Steuergerät ein-und ausgeschaltet.
3 Anschluss Batteriekabel
Das +12V-Versorgungskabel ist am Pluspol der Batterie anzu­schließen. Empfohlener Querschnitt: min. 25 mm2.
4 Sicherungen
Die Eingangssicherungen sind parallel geschaltet und schützen vor einem geräteinternen Fehler, d. h. die Anlage muß mit einer zusätzlichen Sicherung in Nähe der Batterie (max. 30 cm entfernt) abgesichert werden. Die Sicherungswerte betragen 4 x 15 Ampere für die E40.
5 Power / Status LED
Die blaue LED zeigt den Betriebszustand der Endstufe an.
6 Signaleingänge CH 1 + CH 2
Die Esprit-Verstärker haben RCA-Anschlüsse zum Kontaktieren von Cinchkabeln, die mit den Vorverstärkerausgängen der Line­Outputs des Steuergerätes oder eines Vorverstärkers verbunden werden. Diese Anschlüsse sind
vergoldet um eine bessere NF-
Übertragung zu gewährleisten.
7 Levelregler für Eingangsempfindlichkeit CH 1 + CH 2
Mit Hilfe dieser Regler kann die Eingangsempfindlichkeit der Kanäle an die Ausgangsspannung des angeschlossenen Steuer­gerätes angepasst werden. Diese Regler sind keine Lautstärkeregler, sondern dienen nur der Anpassung. Der Regelbereich ist 200 mV bis 4 V.
8 Schalter für Hochpassfilter CH 1 + CH 2
Zur Einschaltung der internen, aktiven Frequenzweiche auf Hochpass. Wird dieser Schalter auf HPF (Hochpass) gestellt, so kann mit Hilfe des Reglers 9 die exakte Übernahmefrequenz für den Hochpass eingestellt werden.
9 Frequenzeinstellregler für den Hochpass CH 1 + CH 2
Regler zur Einstellung der Trennfrequenz von 40 Hz bis 200 Hz
10 Lautsprecheranschlussklemmen CH 1 + CH 2
Zum Anklemmen der Lautsprecherleitungen.
11 Signaleingänge CH 3 + CH 4
Die Esprit-Verstärker haben RCA-Anschlüsse zum Kontaktieren von Cinchkabeln, die mit den Vorverstärkerausgängen der Line­Outputs des Steuergerätes oder eines Vorverstärkers verbunden werden. Diese Anschlüsse sind
vergoldet um eine bessere NF-
Übertragung zu gewährleisten.
12 Levelregler für Eingangsempfindlichkeit CH 3 + CH 4
Mit Hilfe dieser Regler kann die Eingangsempfindlichkeit der Kanäle an die Ausgangsspannung des angeschlossenen Steuer­gerätes angepasst werden. Diese Regler sind keine Lautstärkeregler, sondern dienen nur der Anpassung. Der Regelbereich ist 200 mV bis 4 V.
13 Schalter für Hochpassfilter CH 3 + CH 4
Zur Einschaltung der internen, aktiven Frequenzweiche auf Hochpass. Wird dieser Schalter auf HPF (Hochpass) gestellt, so kann mit Hilfe des Reglers 9 die exakte Übernahmefrequenz für den Hochpass eingestellt werden.
14 Frequenzeinstellregler für den Hochpass CH 3 + CH 4
Regler zur Einstellung der Trennfrequenz von 40 Hz bis 200 Hz.
15 Lautsprecheranschlussklemmen CH 3 + CH 4
Zum Anklemmen der Lautsprecherleitungen.
Verbinden Sie niemals die Lautsprecherleitungen mit der Kfz­Masse (Fahrzeugkarosserie). Dieses kann Ihren Verstärker zerstören.
Achten Sie darauf, dass alle Lautsprechersysteme phasenrichtig angeschlossen sind, d.h. Plus zu Plus und Minus zu Minus. Vertauschen von Plus und Minus hat einen Total- verlust der Basswiedergabe zur Folge. Der Pluspol ist bei den meisten Lautsprechern gekennzeichnet.
Die Impedanz pro Kanal sollte 2 Ohm nicht unterschrei­ten, da sonst eine zu hohe Wärmeentwicklung den Verstärker
zum Abschalten bringen kann.
4
Helix Produkte geniessen aufgrund ihres hohen Qualitätsniveaus international einen ausgezeichneten Ruf. Daher gewähren wir eine Garantiezeit von 2 Jahren. Die Produkte werden während der gesamten Fertigung ständig kontrolliert und geprüft. Bitte beachten Sie im Servicefall folgen­de Hinweise:
1. Die 2-jährige Garantiezeit beginnt mit Kauf des Produktes und gilt nur für den Erstbesitzer.
2.
Während der Garantiezeit beseitigen wir etwaige Mängel,
die nachweislich auf Material- oder Fabrikationsfehlern beru­hen, nach unserer Wahl durch Austausch oder Nach­besserung der defekten Teile. Weitergehende Ansprüche, insbesondere auf Minderung, Wandlung, Schadenersatz oder Folgeschäden sind ausgeschlossen. Ersetzte Teile gehen in das Eigentum von Audiotec Fischer über. Die Garantiezeit wird von einer Garantieleistung durch uns nicht berührt.
3. Am Produkt dürfen keine unsachgemäßen Eingriffe vorge­nommen worden sein.
4. Bei Inanspruchnahme der Garantie wenden Sie sich bitte zuerst an Ihren Fachhändler. Sollte es notwendig sein, das Produkt an uns einzuschicken, so beachten Sie bitte folgen­de Hinweise:
GARANTIEBESTIMMUNGEN
a) Das Produkt muss in einwandfreier Originalverpackung
verschickt werden.
b)
Die Garantiekarte muss ausgefüllt dem Produkt beiligen.
c) Das Produkt muss frachtfrei zugestellt werden, d. h.
Porto und Risiko gehen zu Ihren Lasten
d) Die Kaufquittung muss beiliegen.
5. Von der Garantie ausgenommen sind: a) Transportschäden, sichtbar oder unsichtbar (Reklama-
tionen für solche Schäden müssen umgehend bei der Transportfirma eingereicht werden)
b) Kratzer in Metallteilen, Frontabdeckungen usw. Diese
Defekte müssen innerhalb von 5 Tagen nach Kauf direkt bei Ihrem Händler reklamiert werden.
c) Fehler, die durch fehlerhafte Aufstellung, falschen
An-
schluss, unsachgemäße Bedienung, Beanspruchung
oder
äußere gewaltsame Einwirkung entstanden sind.
d) Unsachgemäß reparierte oder geänderte Geräte, die von
anderer Seite als von uns geöffnet wurden. e) Folgeschäden an fremden Geräten f) Kostenerstattung bei Schadensbehebung durch Dritte
ohne unser vorheriges Einverständnis g) Geräte mit entfernten Typenschildern oder
Seriennummern.
TECHNISCHE DATEN ESPRIT E40
Ausgangsleistung pro Kanal an 4 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 85/100 Watt RMS/Musik
Ausgangsleistung pro Kanal an 2 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . 4 x 110/150 Watt RMS/Musik
Ausgangsleistung gebrückt an 4 Ohm . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 220/300 Watt RMS/Musik
Frequenzbereich . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hz - 20 kHz
Regelbereich Hochpass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hz - 200 Hz
Klirrfaktor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,05%
Geräuschspannungsabstand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 90 dB
TIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,02%
Dämpfungsfaktor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 150
Eingangsimpedanz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 kOhm
Eingangsempfindlichkeit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mV - 4 V
Sicherung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 x 15 Ampere
Abmessungen (H x B x T) in mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 x 470 x 217
Gewicht netto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,1 kg
5
Dear Customer,
congratulations on your purchase of this high-quality HELIX
ESPRIT amplifier. This series highlights best quality, excel-
lent manufacturing and state-of-the-art technology. After
27 years of experiences in the research & development of
audio products this amplifier generation sets new stan-
dards. The attractive typical HELIX ESPRIT design makes
this amplifier an outstanding and top of the class product.
We wish you many hours of enjoyment with your new
HELIX amplifier.
Yours
AUDIOTEC FISCHER Team
General installation instructions for HELIX amplifiers
To find out how HELIX amplifiers work best for you, read this manual carefully and follow the instructions for installation. We guarantee that this product has been checked for proper functio­ning before shipping.
Before you start installation, disconnect the car battery at the minus pole. We would urge you to have the installation work car­ried out by a specialist as verification of correct installation and connection of the unit is a prerequisite for warranty cover of the HELIX amplifier.
Install your amplifier at a dry location where there is sufficient air circulation to ensure adequate cooling of the equipment. For safety reasons, the amplifier must be secured in a professional manner. This is performed by means of four fixing screws scr­ewed into a mounting surface offering sufficient retention and sta­bility.
Before drilling the holes for the screws, carefully examine the area around the installation position and make sure that there are no electrical cables or components, hydraulic brake lines or any part of the petrol tank located behind the mounting surface - otherwi­se these could be damaged. You should be aware of the fact that such components may also be concealed in the double-skin trim panels/mouldings.
General instruction for connecting the amplifiers
The HELIX amplifiers may only be installed in motor vehicles which have a 12-volt minus pole connected to the chassis ground. Any other system could cause damage to the amplifier and the electrical system of the vehicle.
The plus cable from the battery for the complete system should be provided with a main fuse at a distance of max. 30 cm from the battery. The value of the fuse is calculated from the maximum total current input of the car audio system.
Install the cabling in a manner which precludes any danger of the leads being exposed to shear, crushing or rupture forces. If there are sharp edges in the vicinity (e.g. holes in the bodywork) all cables must be cushioned and protected to prevent fraying.
Never lay the power supply cables adjacent to leads and lines connecting other vehicle equipment (fan motors, fire detection modules, gas lines etc.).
In order to ensure safe installation, use only high-quality connections and materials. Ask your dealer for high quality accessories.
ENGLISH
Connecting Bass Remote Bass Remote control Level control for input sensitivity Bass equalizer Phase control Lowpass control Speaker terminals
7 8
9 10 11 12 13
Connecting the ground cable Connecting the remote lead Connecting the battery cable Fuses 4 x 20 ampere Power LED Signal inputs
1 2 3 4 5 6
EQUIPMENT FEATURES AND CONTROL ELEMENTS ESPRIT E10
6
1 Connecting the ground cable
The ground cable should be connected to a central ground refe­rence point (this is located where the negative terminal of the bat­tery is grounded at the metal body of the vehicle), or to a bright bare-metal location on the vehicle chassis, i.e. an area which has been cleaned of all paint residues.
2 Connecting the remote lead
The remote lead is connected to the automatic antenna (aerial positive) output of the head unit (radio). This is only activated if the head unit is switched ON. Thus the amplifier is switched on and off with the head unit.
3 Connecting the battery cable
Connect the +12 V power cable to the positive terminal of the battery. Recommended cross section: min. 25mm
2
.
4 Fuses
The input fuses are connected in parallel and provide protection against an internal equipment fault, i.e. the system must be addi­tionally protected by a further line fuse located in the vicinity of the battery (max. distance from battery: 30 cm). The fuse rating for ESPRIT E10 is 4 x 20 amperes.
5 Power LED
Shows the operation mode of the amplifier.
6 Signal inputs
The ESPRIT amplifiers have RCA connectors for RCA cables that can be connected with the pre-amplifier output of the line-outputs of the headunit or with a pre-amplifier. This connectors are gold­plated to ensure a better signal transmission.
7 Bass remote connector
To control the bass level from the driver position.
8 Bass remote control
To set Bass remote on/off.
9 Level controls for input sensitivity
These controls can be used to match the input sensitivity of the individual channels to the output voltage of the connected head unit. These controls are not volume controls and are solely inten­ded for the purpose of sensitivity trimming. The control range extends from 300 mV to 6 V.
10 Bass equalizer
To raise the bass signal from 0 to 18 dB at 45 Hz.
11 Phase control
This control enables the phase of the bass signal to be shifted by 180° in order to achieve optimum delay equalization with the other channels.
12 Lowpass control
To adjust the crossover frequency from 40 Hz to 150 Hz.
13 Speaker terminals
To connect the speaker cables.
Never connect the loudspeaker cables with the car chas­sis ground. It damages your amplifier. Ensure that the loud-
speaker systems are correctly connected (phase), i.e. plus to plus and minus to minus. Exchanging plus and minus causes a total loss of bass reproduction.The plus pole is indicated on most spea­kers.
The impedance per channel should not be lower than 2 ohms as overheating could cause a shut down of the amplifier
1
3
2
5
4
6
12
11
10
13
7
8
9
7
Cont. power rating at 4 Ohms per channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 350 Watts RMS
Cont. power rating at 2 Ohms per channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 550 Watts RMS
Cont. power rating at 1 Ohm per channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 700 Watts RMS
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Hz - 150 Hz
Setting range lowpass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hz - 150 Hz
Total harmonic distortion (THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,1%
Signal to noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 90 dB
TIM distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,02%
Damping factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 150
Input impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 kOhms
Input sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 mV - 6 V
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 x 20 Ampere
Dimensions (H x W x D) in mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 x 395 x 217
Weight net. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,5 kg
TECHNICAL DATA ESPRIT E10
Signal inputs CH 3 + CH 4 Level controls for input sensitivity Highpass on/off Highpass control Speaker terminals CH 3 + CH 4
11 12 13 14 15
Connecting the ground cable Connecting the remote lead Connecting the battery cable Fuses 4 x 15 ampere Power LED Signal inputs CH 1 + CH 2 Level controls for input sensitivity Highpass on/off Highpass control Speaker terminals CH 1 + CH 2
1 2 3 4 5 6 7 8 9
10
EQUIPMENT FEATURES AND CONTROL ELEMENTS ESPRIT E40
1
3
2
5
4
6
14
12
11
10
13
7
8
9
15
Due to the high quality standard Helix products achieved an excellent international reputation. Therefore we grant a warran­ty period of 2 years. The products checked and tested carefully during the entire pro­duction process. In the case of service note the following:
1) The 2 years warranty period commences with the purchase of the product and is applicable only to the original owner.
2) During the warranty period we will rectify any defects due to faulty material or workmanship by replacing or repai ring the defective part at our decision. Further claims, and in particular those for price reduction, cancellation of sale, compensation for damages or subse quential damages, are excluded. The warranty period is not altered by the fact that we have carried out warranty work.
3) Unauthorized tampering with the product will invalidate this
warranty.
4) Consult your authorized dealer first, if warranty service is needed. Should it be necessary to return the product to the factory, please ensure that
WARRANTY REGULATION
a) the product is packed in original factory packing in
good condition
b) the warranty card has been filled out and attached to the
product
c) the product is shipped prepaid, i.e. at your expense
and risk
d) the receipt/invoice as proof of purchase is enclosed
5) Excluded from the warranty are: a) Shipping damages, either readily apparent or concea-
led (claims for such damages must be immediately notified to the forwarding agent).
b) Scratches in metal parts, front panels or covers etc.
This must be notified to your dealer within 5 days of purchase.
c) Defects caused by incorrect installation or connec-
tion, by operation errors, by overloading or by external force.
d) Products which have been repaired incorrectly or
modified or where the product has been opened by
other persons than us. e) Consoquential damages to other equipments. f) Reimbursement when repairing damages by third
parties without our previous permission.
Gewerbegebiet Lake II · Hünegräben 26 · D-57392 Schmallenberg Tel.: ++49 (0) 29 72-97 88 0 · Fax: ++49 (0) 29 72-97 88 88 E-mail: info@audiotec-fischer.com · Internet: www.audiotec-fischer.com
8
1 Connecting the ground cable
The ground cable should be connected to a central ground refe­rence point (this is located where the negative terminal of the bat­tery is grounded at the metal body of the vehicle), or to a bright bare-metal location on the vehicle chassis, i.e. an area which has been cleaned of all paint residues.
2 Connecting the remote lead
The remote lead is connected to the automatic antenna (aerial positive) output of the head unit (radio). This is only activated if the head unit is switched ON. Thus the amplifier is switched on and off with the head unit.
3 Connecting the battery cable
Connect the +12 V power cable to the positive terminal of the battery. Recommended cross section: min. 25mm
2
.
4 Fuses
The input fuses are connected in parallel and provide protection against an internal equipment fault, i.e. the system must be addi­tionally protected by a further line fuse located in the vicinity of the battery (max. distance from battery: 30 cm). The fuse rating for ESPRIT E40 is 4 x 15 amperes.
5 Power LED
Shows the operation mode of the amplifier.
6 Signal inputs CH 1 + CH 2
The ESPRIT amplifiers have RCA connectors for RCA cables that can be connected with the pre-amplifier output of the line-outputs of the headunit or with a pre-amplifier. This connectors are gold­plated to ensure a better signal transmission.
7 High- and low level signal switch CH 1 + CH 2
To change the input signals from low level (head unit or pre­amplifier) to high level (speaker outputs of head unit). In both cases RCA cables function as line-inputs.
8 Highpass on/off control CH1 + CH 2
If this switch is set on the crossover frequency for the highpass can be adjusted with control 9.
9 Level controls for input sensitivity CH 1 + CH 2
These controls can be used to match the input sensitivity of the individual channels to the output voltage of the connected head unit. These controls are not volume controls and are solely inten­ded for the purpose of sensitivity trimming. The control range extends from 200 mV to 4 V.
10 Speaker terminals CH 1 + CH 2
To connect the speaker cables.
11 Signal inputs CH 3 + CH 4
The ESPRIT amplifiers have RCA connectors for RCA cables that can be connected with the pre-amplifier output of the line-outputs of the headunit or with a pre-amplifier. This connectors are gold­plated to ensure a better signal transmission.
12 High- and low level signal switch CH 3 + CH 4
To change the input signals from low level (head unit or pre­amplifier) to high level (speaker outputs of head unit). In both cases RCA cables function as line-inputs.
13 Highpass on/off control CH 3 + CH 4
If this switch is set on the crossover frequency for the highpass can be adjusted with control 9.
14 Level controls for input sensitivity CH 3 + CH 4
These controls can be used to match the input sensitivity of the individual channels to the output voltage of the connected head unit. These controls are not volume controls and are solely inten­ded for the purpose of sensitivity trimming. The control range extends from 200 mV to 4 V.
10 Speaker terminals CH 3 + CH 4
To connect the speaker cables.
Never connect the loudspeaker cables with the car chas­sis ground. It damages your amplifier. Ensure that the loud-
speaker systems are correctly connected (phase), i.e. plus to plus and minus to minus. Exchanging plus and minus causes a total loss of bass reproduction.The plus pole is indicated on most spea­kers.
The impedance per channel should not be lower than 2 ohms as overheating could cause a shut down of the amplifier.
Cont. power rating at 4 Ohms per channel . . . . . . . . . . . . . . . . . . . . . . . 4 x 85/110 Watts RMS/Music
Cont. power rating at 2 Ohms per channel . . . . . . . . . . . . . . . . . . . . . . 4 x 110/150 Watts RMS/Music
Cont. power rating at bridged at 4 Ohms . . . . . . . . . . . . . . . . . . . . . . . 2 x 220/300 Watts RMS/Music
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hz - 20 kHz
Setting range highpass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hz - 200 kHz
Total harmonic distortion (THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,05%
TIM distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,02%
Signal to noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 90 dB
Damping factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 150
Input impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 kOhms
Input sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mV - 4 V
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 x 15 Ampere
Dimensions (H x W x D) in mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 x 470 x 217
Weight net. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,1 kg
TECHNICAL DATA ESPRIT E40
Loading...