HELIX DSP PRO User Manual

Page 1
DSP PRO
Digitaler 10-Kanal Signalprozessor
Digital 10-channel signal processor
deutsch / english
Page 2
Sehr geehrter Kunde,
Wir gratulieren Ihnen zum Kauf dieses hochwer­tigen HELIX Signalprozessors.
Audiotec Fischer setzt mit dem HELIX DSP PRO neue Maßstäbe im Bereich der Signalprozessor-
technik. Dabei protieren Sie als Kunde direkt von
unserer nahezu 30-jährigen Erfahrung in der For-
schung und Entwicklung von Audiokomponenten.
Dieser Prozessor wurde von uns nach neuesten
technischen Erkenntnissen entwickelt und zeichnet
sich durch hervorragende Verarbeitung und eine
überzeugende Anwendung ausgereifter Technolo­gien aus.
Viel Freude an diesem Produkt wünscht Ihnen das Team von
AUDIOTEC FISCHER
Allgemeines zum Einbau von HELIX-Kompo­nenten
Um alle Möglichkeiten des Produktes optimal aus­schöpfen zu können, lesen Sie bitte sorgfältig die nachfolgenden Installationshinweise. Wir garantie­ren, dass jedes Gerät vor Versand auf seinen ein­wandfreien Zustand überprüft wurde.
Vor Beginn der Installation unterbrechen Sie den Minusanschluss der Autobatterie.
Wir empfehlen Ihnen, die Installation von einem Einbauspezialisten vornehmen zu lassen, da der
Nachweis eines fachgerechten Einbaus und An­schlusses des Gerätes Voraussetzung für die Ga­rantieleistungen sind.
Installieren Sie Ihren DSP PRO an einer trockenen
Stelle im Auto und vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung
erhält. Montieren Sie das Gerät nicht in zu kleine, abgeschlossene Gehäuse ohne Luftzirkulation
oder in der Nähe von wärmeabstrahlenden Teilen
oder elektronischen Steuerungen des Fahrzeuges. Im Sinne der Unfallsicherheit muss der Prozessor professionell befestigt werden. Dieses geschieht über Schrauben, die in eine Montageäche ein­geschraubt werden, die wiederum genügend Halt bieten muss.
Bevor Sie die Schrauben im Montagefeld befesti­gen, vergewissern Sie sich, dass keine elektrischen
Kabel und Komponenten, hydraulische Bremslei-
tungen, der Benzintank etc. dahinter verborgen
sind. Diese könnten sonst beschädigt werden. Ach­ten Sie bitte darauf, dass sich solche Teile auch in
der doppelten Wandverkleidung verbergen können.
Allgemeines zum Anschluss des HELIX DSP PRO
Der DSP darf nur in Kraftfahrzeuge eingebaut wer-
den, die den 12V-Minuspol an Masse haben. Bei
anderen Systemen kann der HELIX DSP PRO und die elektrische Anlage des Kfz beschädigt werden.
Verwenden Sie zum Anschluss des Prozessors an die Stromversorgung des Fahrzeugs aus­schließlich den beiliegenden Anschlussstecker oder das optional erhältliche Easy Plug Kabel! Die Verwendung eines anderen Kabels kann zu Schäden an Ihrer Anlage und des Prozessors führen!
Die Kabelverbindungen müssen so verlegt sein,
dass keine Klemm-, Quetsch- oder Bruchgefahr besteht. Bei scharfen Kanten (Blechdurchfüh­rungen) müssen alle Kabel gegen Durchscheuern
gepolstert sein. Ferner darf das Versorgungskabel niemals mit Zuleitungen zu Vorrichtungen des Kfz
(Lüftermotoren, Brandkontrollmodulen, Benzinlei-
tungen etc.) verlegt werden.
Herzlichen Glückwunsch!
2
Allgemeine Hinweise
Page 3
Anschluss- und Bedienelemente
3
1
Line Input
Cinch-Eingänge zum Anschluss eines Vor-
verstärkersignals
2
Coax Input
Elektrischer Eingang im SPDIF-Format für
digitale Stereosignale
3
Input Switch
Umschalter zwischen „Coax Input“ und „Opti-
cal Input“
4
Optical Input
Optischer Eingang im SPDIF-Format für digi-
tale Stereosignale
5
Clipping LED
Diese LED leuchtet rot, wenn einer der Ana-
logeingänge übersteuert wird
6
Highlevel Input
Hochpegel-Lautsprechereingang zum An-
schluss von Werksradios oder Radios ohne Vorverstärkerausgänge
7
Power Input
Zum Anschluss an die Bordnetzspannung
mit einem zusätzlichen Remote Ein- und Ausgang. Der Remote-Ausgang muss in je­dem Fall zur Einschaltung der Verstärker ge­nutzt werden
8
Masseschalter
Deniert die Verbindung der Masse zwischen
Signaleingang und Signalausgang
9
Control Taster
Dient zum Umschalten oder Löschen der
Setups
10
Status LED
Die Status LED zeigt den Betriebszustand
und den ausgewählten Speicherbereich an
11
USB Eingang
Dient zum Anschluss an den Computer
12
Control Input
Multifunktionsanschluss - dient zum An-
schluss einer Fernbedienung und weiterem HELIX DSP PRO Zubehör
13
Line Output
Vorverstärkerausgänge zum Anschluss
des / der Verstärker/s. Die maximale Aus­gangsspannung beträgt 6 Volt
9
10
11
12
13
8
1 432 6 75
Page 4
1
Line Input
8-Kanal Vorverstärkereingang zum Anschluss von
Signalquellen, z.B. Radios.
Die Eingangsempndlichkeit ist für alle Kanäle ab Werk auf 4 Volt eingestellt. Es ist jedoch möglich, die Empndlichkeit jedes Kanals im Geräteinneren zwischen 2 Volt und 4 Volt zu variieren.
2
Coax Input
Koaxialer Digitaleingang im SPDIF-Format für den Anschluss von Signalquellen mit digitalem Aus­gang. Die „Sampling Rate“ dieses Eingangs muss zwischen 12 - 192 kHz liegen. Das Eingangssignal wird automatisch an die interne Abtastrate ange-
passt. Um diesen Eingang zu aktivieren und in der
Lautstärke regeln zu können, wird eine optional er­hältliche Fernbedienung empfohlen. Hinweis: Es können ausschließlich Stereosignale und keine Dolby-codierten Daten verarbeitet wer­den!
3
Input Switch
Mit dem „Input Switch“ kann man zwischen dem ko­axialen und dem optischen SPDIF-Digitaleingang wählen. Es können nicht beide Eingänge gleichzei­tig genutzt werden.
4
Optical Input
Optischer Eingang im SPDIF-Format für den An­schluss an Signalquellen mit digitalem Ausgang. Die „Sampling Rate“ dieses Eingangs muss zwi­schen 12 - 96 kHz liegen. Das Eingangssignal wird automatisch an die interne Abtastrate angepasst. Um diesen Eingang zu aktivieren und in der Laut­stärke regeln zu können, wird eine optional erhält­liche Fernbedienung empfohlen. Hinweis: Es können ausschließlich Stereosignale und keine Dolby-codierten Daten verarbeitet wer­den!
5
Clipping LED
Diese LED leuchtet rot, wenn einer der acht „Line
Inputs“ oder „Highlevel Inputs“ übersteuert wird.
Die LED hat keine Funktion bei Ansteuerung über
die Digitaleingänge. Sofern diese LED aueuchtet, sollte die Eingangsempndlichkeit über die internen
Trimmer abgesenkt werden bis die LED erlischt.
6
Highlevel Input
8-Kanal Hochpegel-Lautsprechereingang Mit Hilfe dieses Eingangs kann der Prozessor direkt an die Lautsprecherausgänge eines Werks-/ Nach­rüstradios oder eines Werksverstärkers ange­schlossen werden, sofern dieses / dieser nicht über
Vorverstärkerausgänge verfügt. Die Eingangsempndlichkeit ist für alle Kanäle ab Werk auf 10 Volt eingestellt. Es ist jedoch möglich, die Empndlichkeit jedes Kanals im Geräteinneren zwischen 5 - 10 Volt bzw. 10 - 20 Volt zu variieren. Zudem wird bei der
Umschaltung der Wertebereiche durch die interne Steckbrücke (Jumper) auch die Eingangsimpe­danz umgeschaltet, um einen optimalen Betrieb in
Verbindung mit Werksradios oder leistungsfähigen Werksverstärkern zu gewährleisten. Die Eingangs-
impedanz beträgt 30 Ohm im Einstellbereich 5 - 10
Volt und 4 kOhm im Einstellbereich 10 - 20 Volt.
Achtung: Verwenden Sie ausschließlich den mitge- lieferten Stecker mit integrierten Schraubklemmen.
7
Power Input
Diese Buchse dient zum Anschluss des Prozessors
an die Stromversorgung des Fahrzeuges sowie für
die Remote Ein- und Ausgänge. Achtung: Verwenden Sie ausschließlich den mitge- lieferten Stecker mit integrierten Schraubklemmen. Sofern die Hochpegellautsprechereingänge ver­wendet werden, muss der Remote-Eingang nicht belegt werden. Der Remote-Ausgang dient zum prozessorgesteu-
erten Einschalten der Verstärker. Schließen Sie
diesen Remote-Ausgang an die Remote-Eingänge
Ihrer Verstärker an.
Wichtig: Verwenden Sie niemals ein anderes
Inbetriebnahme und Funktionen
4
Page 5
5
Signal als den Remote-Ausgang, um ange-
schlossene Verstärker einzuschalten!
8
Masseschalter
Beim HELIX DSP PRO ist die Masse der Signalein­gänge galvanisch von der Masse der Signalaus­gänge getrennt. Dies ist in den meisten Fahrzeugen die beste Op­tion, um Störgeräusche wie z.B. von der Licht­maschine zu unterbinden. Allerdings gibt es auch Fälle, wo die Massen der Eingänge mit den Aus­gängen direkt „hart“ oder über einen 200 Ohm-Wi-
derstand „weich“ verbunden werden müssen. Der
Masseschalter hat drei Positionen:
- Mittelstellung: Massen galvanisch getrennt
- Linksanschlag: Massen „hart“ zusammenge­schaltet
- Rechtsanschlag: Massen „weich“ gekoppelt
9
Control Taster
Mit Hilfe des Control Tasters lässt sich zwischen den Speicherbereichen eins und zwei umschalten. Zum manuellen Umschalten der zwei Setups muss der Control Taster eine Sekunde lang gedrückt wer-
den. Der Umschaltvorgang wird durch einmaliges
rotes Blinken der Status LED angezeigt. Wird der Taster länger als 5 Sekunden gedrückt, so wird das Gerät resettet und der gesamte interne Speicher gelöscht! Anschließend wird dies durch ein rotes Dauerblinken der Status LED angezeigt. Achtung: Nach dem Resetten des Gerätes kann der HELIX DSP PRO keine Audiosignale mehr wie­dergeben, bis ein neues Sound Setup eingespielt wurde.
10
Status LED
Die Status LED zeigt das aktuell ausgewählte Setup des HELIX DSP PRO an. Leuchtet die LED grün, ist Setup 1 geladen. Bei Setup 2 leuchtet die LED orange. Sollte sich kein Setup im internen Speicher benden, blinkt die LED rot. Sofern letz­teres der Fall ist, muss über die DSP PC-Tool Soft-
ware ein neues DSP Setup eingespielt werden.
11
USB Eingang
Mit Hilfe dieses Eingangs wird der HELIX DSP PRO über das beiliegende Kabel mit dem Com-
puter verbunden und kann anschließend über das DSP PC-Tool konguriert werden.
12
Control Input
Dieser Multifunktionseingang dient zum Anschluss
von HELIX Zubehörprodukten, wie beispielsweise einer Fernbedienung, mit deren Hilfe diverse Funk-
tionen des Prozessors gesteuert werden können. Die Funktionalität muss je nach Typ der Fernbe-
dienung zuerst im „Device Conguration Menu“ der
DSP PC-Tool Software oder an der Fernbedienung
selbst konguriert werden.
13
Line Output
10-Kanal Vorverstärkerausgang zum Anschluss von Verstärkern. Die maximale Ausgangsspannung beträgt 6 Volt. Die Ausgänge können in der DSP
PC-Tool Software den Eingängen beliebig zugeord­net werden.
Page 6
6
Einbau und Installation
Kanalzuordnung:
Kanal A
Kanal B
Kanal C
Kanal D
Kanal H
Kanal G
Kanal F
Kanal E
Einstellen der Eingangsempfindlichkeit der Highlevel-Eingänge:
Jumper oben* Jumper unten
2 V 4 V*
5 V 10 V*
Cinch
2 V 4 V
Hochpegel
10 V 20 V
Eingangsimpedanz
30 Ohm 4 kOhm
Justierung der Eingangsempfindlichkeit für die Nutzung der Kanäle G & H als Aux-Eingang:
Jumper unten*
Kanal G & H:
2 V 4 V*
Jumper oben
Kanal G & H:
250 mV 500 mV
Abb. 1
Abb. 2 Abb. 3
* Auslieferungszustand des HELIX DSP PRO
Page 7
7
Der HELIX DSP PRO wird wie nachfolgend be­schrieben an das Autoradio angeschlossen.
Achtung: Für die Durchführung der nachfolgenden
Schritte werden Spezialwerkzeuge und Fachwissen benötigt. Um Anschlussfehler und Beschädigungen
zu vermeiden, fragen Sie im Zweifelsfall Ihren
Fachhändler und beachten Sie zwingend die all­gemeinen Anschluss- und Einbauhinweise (siehe Seite 2).
1. Anschluss der Vorverstärkereingänge
Diese Eingänge können mit entsprechenden
Kabeln (RCA / Cinch-Kabel) an die Vorverstär­ker- / Lowlevel- / Cinch-Ausgänge des Radios
angeschlossen werden.
Im Prozessor lassen sich die Signaleingänge
über die DSP PC-Tool Software frei den Signal­ausgängen zuweisen. Die Einschaltautomatik des Prozessors funktioniert bei den Vorver­stärkereingängen nicht, so dass der Remote­Eingang des „Power Inputs“ zwingend belegt werden muss.
Achtung: Eine gleichzeitige Verwendung der
Highlevel- und Vorverstärkersignaleingänge ist
nicht möglich und kann zu Schäden an Ihrem Autoradio führen.
2. Anschluss der Highlevel-Lautsprecherein-
gänge
Die Highlevel-Lautsprechereingänge können
direkt mit den Lautsprecherausgängen des Werks- bzw. Nachrüstradios mit Hilfe ent­sprechender Kabel (Lautsprecherkabel mit max. 1mm² Querschnitt) verbunden werden. Dabei müssen nicht zwingend alle Eingänge belegt werden. Achten Sie bitte auf korrekte Polung! Wenn Sie einen oder mehrere An­schlüsse verpolen, kann dadurch die Funkti­on des Prozessors beeinträchtigt werden. Bei Verwendung dieses Eingangs muss der Re­mote-Eingang nicht belegt werden, da sich der Prozessor automatisch einschaltet, sobald ein Lautsprechersignal anliegt.
3. Einstellung der Eingangsempndlichkeit
Um die Eingangsempndlichkeit ändern zu
können, muss das Gerät geöffnet werden. Dazu entfernen Sie die vier Kreuzschlitzschrau-
ben, mit der das Seitenblech auf der Eingangs­seite befestigt ist. Ziehen Sie danach das Bo­denblech heraus. Sie haben nun Zugriff auf die acht Trimmer, mit denen jeder Kanal einzeln justiert werden kann. Die Zuordnung der Trimmer zu den jeweiligen Kanälen entnehmen Sie bitte der Abbildung 1 auf Seite 6. Hinweis: Die Einstellung der Trimmer beein-
usst sowohl die jeweiligen Vorverstärkerein­gänge als auch die Highlevel-Eingänge!
Durch das Umstecken einer Steckbrücke (Jum­per) kann der Stellbereich der Eingangsemp­ndlichkeit der Highlevel-Eingänge variiert wer­den (siehe Abbildung 2 / Seite 6).
Der Stellbereich der Eingangsempndlichkeit der Vorverstärkereingänge G und H lässt sich
durch Umstecken einer weiteren Steckbrü-
cke (Jumper) so verändern, dass auch mobile
Geräte wie z.B. Smartphones mit deutlich ge­ringerer Ausgangsspannung problemlos ange­schlossen werden können (siehe Abbildung 3 / Seite 6).
Um die Eingangsempndlichkeit mit Hilfe der
internen Trimmer optimal an ihre Signalquel­le anzupassen, führen Sie bitte die folgenden Schritte durch:
1. Schließen Sie während dieser Prozedur
keinen Verstärker an die Ausgänge des
Prozessors an.
2. Drehen Sie die Lautstärke Ihres Radios auf 90 % der Gesamtlautstärke und spielen Sie über das CD-Laufwerk ein 1kHz Testsignal
(Vollaussteuerung 0dB) ab.
3. Die Einstellung geht leichter vonstatten,
wenn Sie die Eingangskanäle nacheinan­der anschließen und einstellen.
4. Sollte die Clipping LED bereits leuchten,
verringern Sie mit Hilfe des Trimmers die Eingangsempndlichkeit des jeweiligen Ka-
nals, bis die Clipping LED erlischt.
Sollte der Trimmer bereits auf Rechtsan-
schlag stehen, muss der Wertebereich der
Eingangsempndlichkeit über die internen Jumper verändert werden (siehe Abb. 2 /
Seite 6). Dies hat allerdings nur einen Ein-
uss auf die Highlevel-Eingänge!
5. Erhöhen Sie die Eingangsempndlichkeit
Page 8
8
durch Linksdrehung des jeweiligen Trim­mers bis die Clipping LED aueuchtet. Dre­hen Sie nun den Trimmer im Uhrzeigersinn, bis die Clipping LED wieder erlischt.
6. Wiederholen Sie diesen Vorgang für jeden
genutzten Signaleingang.
4. Anschluss einer digitalen Signalquelle
Sofern Sie über eine Signalquelle mit koaxi-
alem oder optischem Digitalausgang verfügen,
kann diese an den Prozessor angeschlossen werden. Der HELIX DSP PRO ist werksseitig
so konguriert, dass automatisch auf einen der
Digitaleingänge umgeschaltet wird, wenn dort ein Audiosignal anliegt. Diese Funktion kann
über die DSP PC-Tool Software deaktiviert bzw. auf einen manuellen Modus (in Verbindung mit
einer optional erhältlichen Fernbedienung) ge­ändert werden.
Die Einschaltautomatik des Prozessors funktio-
niert bei Verwendung des Digitaleingangs nicht,
so dass der Remote-Eingang des „Power Input“ zwingend belegt werden muss. Eine gleichzei­tige Nutzung der Digitaleingänge sowie der Highlevel- oder der Vorverstärkersignaleingän­ge ist möglich.
Wichtig: Das digitale Audiosignal einer Quel-
le ist üblicherweise nicht Lautstärke geregelt. Das bedeutet, dass an den Signalausgängen
des HELIX DSP PRO der volle Pegel anliegt und die angeschlossenen Verstärker voll aus-
gesteuert werden. Dies kann im Extremfall die Lautsprecher zerstören.
Wir raten deshalb dringend dazu, eine optionale
Fernbedienung zur Einstellung der Lautstärke
der digitalen Signaleingänge zu verwenden!
Hinweis: Der HELIX DSP PRO kann nur un-
komprimierte, digitale Stereo PCM-Signale mit einer Abtastrate zwischen 12 kHz und
96 kHz / 192 kHz verarbeiten. Dolby-codierte
5.1-Signale können genauso wenig verarbei-
tet werden wie komprimierte MP3-/WMA- oder AAC-Datenformate.
5. Anschluss der Stromversorgung
Schließen Sie die Stromversorgung aus-
schließlich über den mitgelieferten Stecker mit Schraubklemmen an.
Achten Sie unbedingt auf die korrekte Polarität.
Die Masseleitung muss an einer nicht isolierten
Stelle mit dem Kfz-Chassis verbunden werden.
Nicht ausreichender Massekontakt führt zu
unerwünschten Störgeräuschen und Fehlfunk­tionen. Die Plusleitung wird entweder direkt an den Pluspol der Batterie oder an einen Strom-
verteiler angeschlossen, der mit dem Pluspol der Batterie verbunden ist. Die Stromaufnahme
des HELIX DSP PRO ist mit ca. 450 mA zwar sehr gering, trotzdem sollten Kabel mit mind.
1 mm² Querschnitt für die Spannungsversor­gung verwendet werden.
6. Anschluss des Remote-Eingangs
Der Remote-Eingang muss mit dem Remote-
Ausgang des Radios verbunden sein, sofern die Vorverstärkereingänge des Prozessors als
Signaleingänge genutzt werden. Es wird drin-
gend davon abgeraten den Remote-Eingang
des Prozessors über das Zündungsplus des Fahrzeugs zu steuern, um Störgeräusche beim
Ein- und Ausschalten zu vermeiden.
Bei Verwendung des Highlevel-Eingangs muss
der Remote-Eingang nicht belegt werden, so­fern das angeschlossene Radio über BTL-Aus-
gangsstufen verfügt.
7. Anschluss des Remote-Ausgangs
Dieser Ausgang dient dazu, die angeschlos-
senen Verstärker mit einem Remote-Signal zu versorgen. Bitte verwenden Sie ausschließlich dieses Signal zur Einschaltung der Verstärker, um Ein- und Ausschaltgeräusche zu vermei-
den.
Einbau und Installation
Page 9
9
Anschluss mit Hilfe des „Easy Plug Cables“
Um die Installation des DSP PRO an ein Werks-
oder Nachrüstradio deutlich zu vereinfachen,
kann das Gerät auch mit Hilfe des optional er­hältlichen Easy Plug Kabels (EPC 5.2 - Art.-Nr. HZ45000) angeschlossen werden. Über dieses Kabel wird der Prozessor sowohl mit Strom als auch mit den Lautsprechersignalen des Radios
versorgt. Zudem muss bei dieser Installation
kein Kabel des Werkssoundsystems durch­trennt werden. Das Easy Plug Kabel unterstützt allerdings nur vier der acht Lautsprecherein­gänge des HELIX DSP PRO. Im folgenden wird der Anschluss an das Werksradio beschrieben:
1. Nachdem das Radio mit Hilfe der entspre­chenden Werkzeuge ausgebaut ist, trennen Sie den Fahrzeugkabelbaum vom Autoradio. Ver­binden Sie den Fahrzeugkabelbaum anschlie­ßend mit der Kupplung des Easy Plug Kabels. Je nach Fahrzeugtyp benötigen Sie hierfür
gegebenenfalls einen fahrzeugspezischen
ISO-Adapter. Eine Liste aller Fahrzeuge und
der eventuell benötigten Adapter nden Sie auf www.audiotec-scher.com.
2. Verbinden Sie die Stecker des Easy Plug Ka- bels mit dem Autoradio.
3. Verbinden Sie den Highlevel-Stecker (8-poliger Stecker) und den Stromversorgungsstecker
(4-poliger Stecker) mit den jeweiligen Eingän­gen des DSP PRO. Es ist Ihnen überlassen, ob
Sie den Highlevel-Stecker mit den Eingängen A-D oder E-H verbinden.
4. Beim Anschluss der Stromversorgung muss fol- gendes noch beachtet werden: Je nach Fahrzeugtyp können die Anschlüsse
für Zündplus und Dauerplus vertauscht sein. Der DSP sollte die Stromversorgung jedoch
nicht über die Zündleitung beziehen, da es sonst zu Störgeräuschen kommen kann. Aus diesem Grund muss vor der endgültigen In- betriebnahme die Zuordnung von Zündplus und Dauerplus an der roten und der blauen
Leitung vom ISO-Stecker kommend, mit einem Voltmeter überprüft werden. Dauerplus ist die
Leitung, an der auch bei ausgeschalteter Zün-
dung eine Spannung von 12V messbar ist. Verbinden Sie nach erfolgter Messung das rote
Kabel, zum HELIX DSP PRO führend, mit dem Dauerplus-Kabel (entweder das blaue Kabel mit Stecker oder das rote Kabel mit Stecker). Die Plusleitung des Kabelbaums ist in der Re­gel mit max. 20A abgesichert. Hinweis: Im Auslieferungszustand ist das rote
Kabel vom ISO-Stecker bis zum DSP PRO schon verbunden, da diese Variante in den mei-
sten Fällen zutrifft.
Sollten Sie sich bezüglich der Zuordnung nicht sicher sein, fragen Sie Ihren Fach­händler.
Hinweis: MOST-Bus
Bei einigen Fahrzeugen kann es notwendig sein, die Lichtleiterverbindung aus dem Original-Radio­anschlussstecker auszulösen und stattdessen in den Radio-Stecker eines ISO-Adapters einzuste­cken. Hierfür ist extra eine Aussparung im ISO-
Adapter vorhanden. Dies ist zwingend bei allen
Fahrzeugen notwendig, die einen Lichtleiteran­schluss im Originalradiokabelbaum haben.
Page 10
10
Der HELIX DSP PRO kann mit Hilfe der DSP PC-Tool Software frei konguriert werden. Die Soft­ware stellt alle Funktionen übersichtlich und bedie-
nerfreundlich zur Verfügung, so dass Sie diese in­dividuell einstellen können. Dabei können alle zehn
DSP Kanäle separat eingestellt werden.
Bevor Sie den HELIX DSP PRO das erste Mal an
einen Computer anschließen, gehen Sie auf unsere Homepage und laden Sie sich die aktuellste Soft-
ware-Version herunter. Es ist ratsam, regelmäßig
nach Updates der Software zu schauen, damit das Gerät immer auf dem aktuellsten Stand ist. Die Software sowie die dazugehörige Bedienungs-
anleitung nden Sie auf www.audiotec-scher.com.
Es wird dringend empfohlen die Bedienungsanlei-
tung der Software vor der ersten Benutzung durch­zulesen, um Komplikationen und Fehler zu vermei-
den. Wichtig: Stellen Sie sicher, dass der HELIX DSP PRO bei der ersten Installation der Software noch nicht an den PC angeschlossen ist. Verbinden Sie diesen erst, wenn die Software voll­ständig installiert ist!
Im folgenden Abschnitt nun die wichtigsten Schritte zum Anschluss und der ersten Inbetriebnahme:
1. Laden Sie die DSP PC-Tool Software unter
www.audiotec-scher.com herunter.
2. Installieren Sie die Software auf ihrem Compu­ter. Während der Installation wird automatisch auch der USB-Treiber für das Gerät installiert.
3. Nach der Installation können Sie den Prozessor mit dem beiliegenden USB-Kabel an den Com-
puter anschließen. Verlängern Sie das Kabel auf keinen Fall mit einer passiven USB-Verlän-
gerung, weil eine einwandfreie Kommunikation zwischen dem HELIX DSP PRO und Ihrem PC nicht sicher gestellt werden kann. Wenn Sie
längere Distanzen zu überbrücken haben, ver­wenden Sie bitte eine aktive USB-Verlängerung
mit integriertem Repeater.
4. Schalten Sie den HELIX DSP PRO ein und starten Sie die Software. Wenn die Betriebs­software des Prozessors nicht mehr aktuell ist, wird diese automatisch aktualisiert.
5. Sie können nun den HELIX DSP PRO mit der
DSP PC-Tool Software frei kongurieren.
Achtung: Es wird dringend empfohlen, vor der er­sten Inbetriebnahme an die Vorverstärkerausgänge des HELIX DSP PRO noch keine Verstärker anzu-
schließen bis die grundlegenden Einstellungen im
Prozessor vorgenommen wurden. Bei Missachtung
kann es zur Zerstörung der angeschlossenen Laut­sprecher kommen. Gerade bei vollaktiven Syste­men besteht diese Gefahr.
Anschluss an den Computer
1
Laden und Speichern
2
Hauptmenü
3
Kanalkonfiguration
4
Hochpassfilter
5
Tiefpassfilter
6
Laufzeitkorrektur
7
Ausgangspegel
8
Frequenzgraph
9
Auswahl Frequenzgraphen
10
Equalizer
11
EQ Feineinstellung
8
1
6
3
4
7
5
2
9
10 11
Page 11
11
96 kHz Abtastrate
Der HELIX DSP PRO bietet eine Signalverarbeitung mit einer doppelten Abtastrate von 96 kHz. Dadurch
ist die Audiobandbreite nicht wie üblich auf 22 kHz begrenzt, sondern erlaubt einen ausgedehnten Fre­quenzgang bis über 40 kHz. Die höhere Abtastrate stellt aber deutlich höhere Anforderungen an den DSP selbst, denn die Anzahl der möglichen Re-
chenoperationen wird bei einer Verdoppelung der
Abtastrate auf die Hälfte reduziert. Erst der Einsatz der allerneuesten Chipgeneration ermöglicht es, trotz weiter gesteigertem Funktionsumfang und Ka­nalanzahl die Abtastrate auf 96 kHz anzuheben.
Power Save Modus
Der Power Save Modus ist in der Grundeinstellung
implementiert. Er erlaubt es, die Leistungsaufnah­me der an den Prozessor angeschlossenen Ver­stärker drastisch zu reduzieren, wenn für länger als 60 sec. kein Eingangssignal anliegt. Es ist zu
berücksichtigen, dass heutzutage viele Fahrzeuge
mit „CAN“ oder ähnlichen internen Bussystemen ausgestattet sind, die das Radio für den Anwender „unsichtbar“ noch bis zu 45 min. eingeschaltet las­sen, selbst wenn man zwischenzeitlich das Fahr-
zeug verlassen und abgeschlossen hat. Sobald der „Power Save Mode“ aktiv ist, wird der
„Remote Output“ und damit die angeschlossenen
Verstärker abgeschaltet. Der HELIX DSP PRO re­aktiviert den Remote Output innerhalb von 1 Sekun-
de, sobald wieder ein Musiksignal an einem seiner Eingänge anliegt. Es ist zudem möglich, über die
DSP PC-Tool Software die Abschaltverzögerung zu variieren bzw. den „Power Save Mode“ komplett zu deaktivieren.
Start-Stopfähigkeit
Das Netzteil im HELIX DSP PRO stellt die interne
Spannungsversorgung auch bei kurzfristigen Ein­brüchen bis hinab zu 6 Volt sicher.
Damit ist gewährleistet, dass der HELIX DSP PRO
auch beim Motorstart voll funktionsfähig bleibt.
Automatic Digital Signal Detection
Die Umschaltung zwischen den analogen und einem der beiden Digitaleingänge erfolgt signalge­steuert. Sobald ein Audiosignal am „Coaxial Input“ oder „Optical Input“ detektiert wird (Schalterstellung „Input Switch“ beachten). schaltet der Prozessor auf diesen Eingang um. In der DSP PC-Tool Software
kann diese Funktion deaktiviert oder alternativ eine
manuelle Steuerung über eine optional erhältliche Fernbedienung gewählt werden.
Spezielle Features des HELIX DSP PRO
Der HELIX DSP PRO kann durch die Montage ei­ner HELIX Extension Card (HEC) um weitere Funk­tionen erweitert werden - beispielsweise um eine Bluetooth Audiostreaming Funktion, einem weiteren optischen Digitaleingang oder einem optischen Di­gitalausgang.
Zur Montage einer HEC muss das Seitenblech des DSP PRO demontiert und gegen das dem HEC bei­liegende Seitenblech ausgetauscht werden. Detail-
lierte Informationen zum Einbau nden Sie in der
Bedienungsanleitung der jeweiligen HELIX Exten­sion Card.
HELIX Extension Card Slot (HEC Slot)
HELIX Extension Card Slot
Page 12
12
Eingänge .........................................................................8 x Cinch
8 x Hochpegel-Lautsprechereingang 1 x Optisch SPDIF-Format (12 - 96 kHz) 1 x Coax SPDIF-Format (12 - 192 kHz) 1 x Remote In
Eingangsempndlichkeit .................................................. Cinch 2 - 4 Volt - Standard 4 Volt
Hochpegel 5 - 10 Volt oder 10 - 20 Volt (ent-
spricht 6 - 100 Watt RMS - nicht max. Power) -
Standard 10 Volt
Ausgänge ........................................................................10 x Cinch
1 x Remote Out
Ausgangsspannung ......................................................... 6 Volt RMS
Frequenzbereich..............................................................10 Hz - 44.000 Hz
DSP Auösung ................................................................64 Bit
DSP Rechenleistung .......................................................295 MHz (1.2 Mrd. MAC Operationen/Sekunde)
DSP Typ ..........................................................................Audio Signalprozessor
Signalwandler .................................................................. A/D: Asahi Kasei
D/A: Analog Devices
Signal-/ Rauschabstand Digitaleingang...........................116 dB (A-bewertet)
Signal-/ Rauschabstand Analogeingang..........................108 dB (A-bewertet)
Klirrfaktor (THD+N) Digitaleingang .................................. < 0,0006 %
Klirrfaktor (THD+N) Analogeingang ................................. < 0,001 %
Intermodulationsverzerrungen Digitaleingang ................. < 0,002 %
Intermodulationsverzerrungen Analogeingang ................< 0,006%
Übersprechen .................................................................. > 90 dB bei 10 kHz
Betriebsspannung............................................................9,6 - 18 Volt, kurzzeitige Spannungseinbrüche
(bis 5 Sek.) bis auf 6 Volt sind zulässig
Stromaufnahme ............................................................... 450 mA
Zusätzliche Features .......................................................Control Input, USB, Masseschalter, HEC Slot
Abmessungen (H x B x T) ...............................................40 x 177 x 150 mm
Die Garantieleistung entspricht der gesetzlichen Regelung. Von der Garantieleistung ausgeschlos­sen sind Defekte und Schäden, die durch Überla­stung oder unsachgemäße Behandlung entstanden
sind. Eine Rücksendung kann nur nach vorheriger Absprache in der Originalverpackung, einer de-
taillierten Fehlerbeschreibung und einem gültigen Kaufbeleg erfolgen.
Technische Änderungen und Irrtümer vorbehalten!
Für Schäden am Fahrzeug oder Gerätedefekte, hervorgerufen durch Bedienungsfehler des Gerätes, können wir keine Haftung übernehmen. Alle HELIX Produkte sind sowohl mit einer E-Kennzeichnung als auch einer CE-Kennzeich­nung versehen. Damit sind die Geräte für den Be­trieb in Fahrzeugen innerhalb der Europäischen
Union (EU) zertiziert.
Technische Daten
Garantiehinweis
Page 13
13
Dear Customer,
Congratulations on your purchase of this high-qual­ity HELIX product.
With the HELIX DSP PRO, Audiotec Fischer is set­ting new standards for digital signal processors.
We wish you many hours of enjoyment with your new HELIX DSP PRO.
Yours, AUDIOTEC FISCHER
General installation instructions for HELIX components
To prevent damage to the unit and possible injury,
read this manual carefully and follow all installati­on instructions. This product has been checked for proper function prior to shipping and is guaranteed against manufacturing defects.
Before starting your installation, disconnect the battery’s negative terminal to prevent
damage to the unit, re and / or risk of injury. For a proper performance and to ensure full warranty coverage, we strongly recommend to get this pro­duct installed by an authorized HELIX dealer.
Install your HELIX DSP PRO in a dry location with
sufcient air circulation for proper cooling of the
equipment. The processor should be secured to a solid mounting surface using proper mounting hardware. Before mounting, carefully examine the area around and behind the proposed installati­on location to insure that there are no electrical cables or components, hydraulic brake lines or any part of the fuel tank located behind the mounting surface. Failure to do so may result in unpredictable damage to these components and possible costly
repairs to the vehicle.
General instruction for connecting the HELIX DSP PRO
The HELIX DSP PRO may only be installed in ve­hicles which have a negative ground electrical sys-
tem. Any other system may cause damage to the
processor and the electrical system of the vehicle.
Use only the provided connectors or an Easy Plug Cable for the connection of HELIX DSP PRO. The use of other cables can result in damage of the amplier, the head unit / radio or the connected loudspeakers!
Prior to installation, plan the wire routing to
avoid any possible damage to the wire harness.
All cabling should be protected against possible
crushing or pinching hazards. Also avoid routing
cables close to potential noise sources such as electric motors, high power accessories and other
vehicle harnesses.
Congratulations!
General instructions
Page 14
14
Connectors and control units
1
Line Input
RCA inputs for connecting pre-amplier sig-
nals
2
Coax Input
Electrical input for digital stereo signals
(SPDIF format)
3
Input Switch
Selector between „Coax Input“ and „Optical
Input“
4
Optical Input
Optical input for digital stereo signals (SPDIF
format)
5
Clipping LED
This LED lights up red if one of the analog
inputs is overdriven
6
Highlevel Input
Highlevel speaker inputs for connecting a
factory radio or an aftermarket radio without pre-amp / line outputs
7
Power Input
Connector for the DC power supply with an
additional remote in- and output. The remote output has to be used to switch on external
ampliers
1 432 6 75
9
10
11
12
13
8
8
Ground lift switch
Can be used to dene the connection be-
tween the grounding of the inputs and out­puts
9
Control pushbutton
Use this button to either switch between the
setups or initiate a reset of the device
10
Status LED
This LED indicates the operating mode of the
DSP and which setup has been chosen
11
USB input
Connects the HELIX DSP PRO to your PC
12
Control Input
Multifunction interface for e.g. an optional
remote control or other HELIX DSP PRO ac­cessory
13
Line Output
Pre-amplier outputs for connecting the
amplier/s. The maximum output voltage is 6 Volts
Page 15
15
1
Line Input
8-channel pre-amplier input to connect signal sourc es such as radios. Input sensitivity is set to 4 Volts. It is possible to vary the sensitivity of each channel from 2 Volts to 4 Volts inside the device.
2
Coax Input
Coaxial input in SPDIF format for connecting sour­c es with a digital audio output. The sampling rate of this input has to be in the range of 12 and 192 kHz. The input signal is automatically adjusted to the in-
ternal sample rate. In order to control the volume of
this input, we recommend to use an optional remote control. Notice: This processor can only handle stereo input signals and no Dolby-coded digital audio stream.
3
Input Switch
With the Input Switch it is possible to choose bet­ween the Coax Input“ and „Optical Input“. It is not possible to use both inputs at the same time.
4
Optical Input
Optical input in SPDIF format for connecting signal sources with a digital audio output. The sampling rate of this input must be between 12 and 96 kHz. The input signal is automatically adjusted to the in­ternal sample rate. In order to control the volume of this input, we re­commend to use an optional remote control. Notice: This processor can only handle stereo input signals and no Dolby-coded digital audio stream.
5
Clipping LED
This LED lights up red if one of the eight „Line In-
puts“ or „Highlevel Inputs“ is overdriven. The LED has no function if the device is fed with digital input
signals.
6
Highlevel Input
8-channel highlevel loudspeaker input.
Use this input to connect the processor directly to loudspeaker outputs of OEM / aftermarket radios
or OEM ampliers that do not have any pre-ampli­er outputs. Input sensitivity is set to 10 Volts for all channels. It is possible to vary the sensitivity of each channel from 5 - 10 Volts rep. 10 - 20 Volts inside the device. By changing the sensitivity range, the input impe­dance of the highlevel inputs is shifted as well in or-
der to guarantee a perfect operation in combination
with OE radios and high-power OE ampliers. Input impedance is set to 30 Ohms for a sensitivity range of 5 - 10 Volts and 4 kOhms for a sensitivity range of 10 - 20 Volts.
Attention: Solely use the pluggable screw-terminal
for the highlevel connector which is included in de­livery!
7
Power Input
This input is used for connecting the processor
to the power supply of the vehicle and for remote
in / out.
If the highlevel loudspeaker inputs are used the
remote input can be left unconnected. The remote
output is used to control amplier switching on and off via the processor. Connect this remote output to the remote inputs of your amplier.
Attention: Solely use the pluggable screw-terminal
which is included in delivery!
Important: Never use a different signal than the
remote output of the DSP to activate connected
ampliers!
Initial start-up and functions
Page 16
8
Ground Lift Switch
The ground of the HELIX DSP PRO signal inputs is
galvanically decoupled from the ground of the sig-
nal outputs. In many cars this setup is the best way
to avoid alternator noise. Nevertheless there are use cases where it will be
necessary to directly connect input and output
ground or to tie both grounds together via a resis tor.
Therefore the “Ground Lift Switch” has three posi­tions:
- center position: input and output ground separat ed
- left position: input and output ground tied togeth­er
- right position: input and output ground con-
nected via 200 Ohms resistor
9
Control pushbutton
The control pushbutton allows the user to switch between the two setup memory positions. To switch between the setups the button has to be pressed and held for 1 second. Switching is indicated by a
single red ash of the Status LED.
Pressing the button for 5 seconds completely eras­es the internal memory. This is indicated by a con-
stant ashing of the Status LED.
Attention: After erasing the setups from memory the HELIX DSP PRO will not reproduce any audio output.
10
Status LED
The Status LED indicates the current active DSP
setup. Green means that setup 1 is load ed, orange
means that setup 2 is loaded. A ashing red light
indicates that no setup is loaded.
In that case please load a new setup via the
DSP PC-Tool software.
11
USB Input
Connect your personal computer to the HELIX DSP
PRO using the provided USB cable. The required DSP PC-Tool software to congure this amplier
can be downloaded from the Audiotec Fischer web-
site www.audiotec-scher.com.
12
Control Input
This multi-functional input is designed for HELIX DSP PRO accessory products like a remote control
which allows to adjust several features of the signal
processor. Depending on the type of remote con-
trol, the functionality at rst has to be dened in the “Device Conguration Menu” of the DSP PC-Tool
software or on the remote control itself.
13
Line Output
10-channel pre-amplier output These are used to connect external ampliers. The output voltage is 6 Volts max. The outputs can be
assigned to any of the inputs as desired using the DSP PC-Tool software.
16
Initial start-up and functions
Page 17
17
Installation
Channel assignment:
Channel A
Channel B
Channel C
Channel D
Channel H
Channel G
Channel F
Channel E
Adjustment of the input sensitivity for using channel G & H as aux inputs:
Jumper below*
Channel G & H:
2 V 4 V*
Jumper above
Channel G & H:
250 mV 500 mV
Fig. 1
Fig. 3
Adjustment of the input sensitivity of the highlevel inputs:
Jumper above* Jumper below
2 V 4 V*
5 V 10 V*
RCA / Cinch
2 V 4 V
Highlevel
10 V 20 V
Input impedance
30 Ohm 4 kOhm
* Ex factory adjustment of HELIX DSP PRO
Fig. 2
Page 18
Connection of HELIX DSP PRO to the head unit (radio):
Caution: Carrying out the following steps will re-
quire special tools and technical knowledge. In or-
der to avoid connection mistakes and / or damage, ask your dealer for assistance if you have any ques-
tions and follow all instructions in this manual (see page 13). It is recommended that this unit will be installed by an authorized HELIX dealer.
1. Connecting the pre-amplier inputs
Use the correct cable (RCA / cinch cable) to con-
nect these inputs to the pre-amplier / lowlev el /
cinch outputs of your car radio.
Each input can be assigned to any output using
the DSP PC-Tool software. The automatic turn­on circuit does not work when using the pre-
amplier inputs. In this case the „Remote Input“ has to be connected to activate the HELIX DSP
PRO.
Important: It is strictly forbidden to use the
highlevel input and pre-amplier inputs at the same time. This may cause severe damage to the pre-amplier outputs of your car radio.
2. Connecting the highlevel speaker inputs
The highlevel loudspeaker inputs can be con-
nected directly to the loudspeaker outputs of an OEM or aftermarket radio using appropriate cables (loudspeaker cables with 1mm² / AWG18 max.). It is not mandatory to use all speaker in­puts.
Make sure that the polarity is correct. If one or
more connections have reversed polarity this
may affect the performance of the processor. If this input is used the remote input has not to be used as the processor will automatically turn on
once a loudspeaker signal is received.
3. Adjustment of the input sensitivity
If you want to change the input sensitivity you
have to open the device at rst. Remove the
four Philipps head screws of the side pan el (in­put side) and pull out the bottom plate. Now you
have access to the eight trim potentiometers that allow adjusting each channel individually.
The assignment of the trim pots to the respec-
tive channels is shown in the gure 1 on page
17.
Please note: The settings of the trim potentio-
meters affects both the lowlevel inputs and the highlevel inputs!
The sensitivity range of the highlevel inputs can
be modied by inserting the jumper into the op­posite position (see gure 2 / page 17). The sensitivity range of the two lowlevel inputs
G and H can be changed by inserting the other
jumper into the opposite position (see gure 3 / page 17). Thus it is possible to connect even mobile devices with signicantly lower output voltage (like smartphones) to the HELIX DSP
PRO. Follow the subsequent steps if you like to per-
fectly adapt the processors input sensitivity to
your audio source by using the internal trim po­tentiometers:
1. Don‘t connect any amplier to the outputs of
the processor during this setup.
2. Adjust the volume of your radio to approx. 90 % of the max. volume and playback a 1 kHz full scale test tone (0 dB) via CD drive.
3. The adjustment will be easier when you connect and adjust one input channel after the other.
4. If the Clipping LED already lights up, you
have to reduce the input sensitivity via the respective trim potentiometer until the LED
goes out.
If the pot is already set to right stop position
then it will be necessary to change the sen-
sitivity range by repositioning the jumper (see gure 2 / page 17). Note that this will only have an effect on the highlevel inputs!
5. Increase the input sensitivity by turning the respective pot counterclockwise until the
LED lights up. Now turn the potentiometer clockwise until the Clipping LED goes out again.
6. Repeat this process for each channel you are using.
4. Connecting a digital signal source
If you have a signal source with optical or coa-
xial digital output you can connect it to the pro­cessor using the appropriate input.
18
Installation
Page 19
In standard conguration the HELIX DSP PRO
automatically activates the used digital input if
an digital audio signal is detected. This function
can be deactivated via the DSP PC-Tool soft­ware. Alternatively you can manually activate
the digital input if you are using the optional re­mote control.
The automatic turn-on circuit does not work
when the digital input is used. Therefore it is mandatory to connect the „Remote In“ at the
power input if none of the highlevel inputs are
used.
Please note that it is possible to connect a sour-
ce to one of the digital inputs and the highlevel or the pre-amplier at the same time.
Important: The signal of a digital audio source normally does not contain any information about
the volume level. Keep in mind that this will lead to full level on the outputs of the HELIX DSP PRO and your connected ampliers. This may cause severe damage to your speakers.
We strongly recommend to use an optional re-
mote control for adjusting the volume level of
the digital signal input! Information: The HELIX DSP PRO can only handle uncompressed digital stereo signals in PCM format with a sample rate between 12 kHz and 96 kHz / 192 kHz. Neither Dolby-coded
5.1 signals nor compressed MP3-/WMA- or AAC-audio formats will be accepted.
5. Connection to power supply
Solely use the included screw-type terminal to connect the HELIX DSP PRO to a power sup­ply. Make sure of correct polarity. The ground
wire must be connected to the vehicle chassis
at a non-insulated point. Inadequate grounding causes audible interference and malfunctions.
The positive wire has to be connected to the battery positive terminal or to a power distributi-
on block. Though the current draw of the HELIX DSP PRO is rather low (approx. 450 mA) we recommend a minimum wire gauge of 1 mm² / AWG18 for both power supply wires.
6. Connecting the remote input
The remote input has to be connected to the radio remote output if the processor’s pre-am-
plier inputs are used as signal inputs. We do not recommend controlling the remote input via the ignition switch to avoid pop noise during turn
on / off.
If the highlevel inputs are used this input does
not need to be connected as long as the car ra­dio has BTL output stages.
7. Connecting the remote output
This output is used to supply remote signals to
the external amplier/s. Always use this remote output signal to turn on the ampliers in order to avoid on/off switching noises.
19
Page 20
20
To simplify installing to an OEM or aftermarket ra­dio the HELIX DSP PRO can also be connected using the optional Easy Plug Cable (EPC 5.2 - art.­no. HZ45000) which will supply the processor with both power and loudspeaker signals of the radio. No factory wires or plugs need to be cut using this connection method. Connection to an OEM radio is detailed below:
1. Once the radio has been removed by using the
right tools disconnect the OEM harness from the radio. Connect the vehicle cable jack con­nectors of the Easy Plug Cable. You may need
a special ISO-adaptor depending on vehicle type. In order to varify please check the adaptor
database on the Audiotec Fischer homepage
www.audiotec-scher.com.
2. Connect the cable plugs to the car radio.
3. Connect the highlevel plug (8-pole connector)
and the power supply plug (4-pole connector) to the appropriate HELIX DSP PRO inputs.
4. Please note when connecting the power supply:
The constant and switched 12 Volts can be re­versed depending on vehicle type.
The HELIX DSP PRO should not be plugged
into the power supply via the ignition cable as
this may cause interference. Before connecting the Easy Plug Cable to the HELIX DSP PRO,
verication of the constant 12 Volts wire must be
made between the blue and red wires coming from the ISO connectors of the harness with a
voltmeter. The constant 12 Volts wire will show voltage even when the ignition is turned off. Once the correct wire is identied connect the
red wire with jack to the corresponding blue or red wire with plug. The positive cable of the har­ness usually has a fuse of max. 20 A. Attention: The ex factory condition is that the red wires are connected.
If you’re uncertain of assignment ask your dealer.
Note - Cars equipped with MOST bus:
In cars equipped with MOST bus structure it is
mandatory to unplug the ber-optic cable from the
original radio connector and insert it into the ISO adaptor, which has a dedicated recess for this.
Installation with „Easy Plug cable“
Page 21
21
It is possible to freely congure the HELIX DSP
PRO with our DSP PC-Tool software. The user in­terface is designed for easy handling of all functions
and allows an individual adjustment of each of the
10 channels. Prior to connecting the processor to
your PC, visit our website and download the latest version of the DSP PC-Tool software. Check from
time to time for software updates.
You will nd the software and the respective user manual on www.audiotec-scher.com.
We strongly recommend to carefully read the user
manual before using the software for the rst time in order to avoid any complications and failures.
Important: Make sure that the processor is not con­nected to your computer before the software and
USB driver are installed!
To install the software follow the next steps:
1. Download the DSP PC-Tool software from the
website www.audiotec-scher.com
2. Install the software on your computer. During that process the required USB driver will be au­tomatically installed as well.
3. After the software installation process is com­pleted you can now connect the processor to
your PC using the provided USB cable. Don’t extend the supplied cable by using any passive USB extension cable. If you need to cover lo ng-
er distances between your PC and the HELIX DSP PRO then use an active USB repeater ca­ble.
4. Turn on the processor and then start the soft-
ware. If the rmware is not the latest version it
will automatically be updated.
5. You are now ready to congure the HELIX
DSP PRO according to your demands.
Comprehensive operating instructions
for the software can be downloaded from
www.audiotec-scher.com.
Caution: We strongly recommend to not connect
any external ampliers to the pre-amplier outputs of HELIX DSP PRO before the basic congurati-
on of the processor has been completed. Ignoring
this advice may result in damaging the connected speakers, especially if you are running a fully active conguration.
Connection to a PC
1
Load and save
2
Main menu
3
Channel configuration
4
Highpass filter
5
Lowpass filter
6
Time alignment
7
Output level
8
Frequency graph
9
Range of frequency graphs
10
Equalizer
11
EQ fine adjustment
8
1
6
3
4
7
5
2
9
10 11
Page 22
22
96 kHz sampling rate
The HELIX DSP PRO allows to handle all signal management with the doubled sampling rate of 96 kHz. Thus the audio bandwidth is no long er li­mited to usual values like 22 kHz but allows an ex­tended frequency response to more than 40 kHz.
Doubling the sampling rate requires signicantly
higher DSP power as the number of possible arith-
metic operations is halved. Only the implementation
of the latest DSP chip generation allows raising the sampling rate to 96 kHz and adding new features plus additional channels at the same time.
Power Save Mode
The Power Save Mode is incorporated in the bas­ic setup. It allows to signicantly reduce the power consumption of the ampliers that are connected to
the HELIX DSP PRO once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with “CAN” or any other internal bus structures it may happen
that the radio remains “invisibly” turned on for up to 45 min. even after leaving the car! Once the “Power Save Mode“ is active the Remote Output and therefore the connected ampliers will
be turned off.
The HELIX DSP PRO will reactivate the Remote
Output within a second if a music signal is applied. It is possible to either modify the turn-off time of
60 sec. or completely deactivate the “Power Save Mode” via the DSP PC-Tool software.
Start-/Stop capability
The switched power supply of the HELIX DSP PRO
assures a constant internal supply voltage even if the battery’s voltage drops to 6 Volts during engine
crank.
Automatic Digital Signal Detection
Switching from analog input to the digital input is done automatically as soon as a signal is detected
on the optical input. This feature can be deactivated in the DSP PC-Tool software. Alternatively you can
use an optional remote control for man ual switching between analog and digital inputs.
HELIX Extension Card Slot (HEC Slot)
Unique Features of the HELIX DSP PRO
It is possible to extend the functionality of the HELIX DSP PRO by inserting an optional HELIX Extension Card (HEC) - for example a Bluetooth Audio Strea­ming module, an additional optical digital input or an optical digital output. To install a HELIX Extension Card it is necessary
to remove the side panel of the DSP PRO and re­place it by a new side panel that comes with the HEC. Any further mounting information will be found
in the instruction manual of the respective HELIX
Extension Card.
HELIX Extension Card Slot
Page 23
23
Inputs ............................................................................... 8 x RCA / Cinch
8 x Highlevel speaker input
1 x Optical SPDIF (12 - 96 kHz) 1 x Coax SPDIF (12 - 192 kHz) 1 x Remote in
Input sensitivity ................................................................ RCA / Cinch 2 - 4 Volts (adjustable) -
default 4 Volts Highlevel 5 - 10 or 10 - 20 Volts (corresponds
to 6 - 100 Watts RMS - not max. power) -
default 10 Volts
Outputs ............................................................................ 10 x RCA / Cinch
1 x Remote out
Output voltage .................................................................6 Volts RMS
Frequency response ........................................................ 10 Hz - 44,000 Hz
DSP resolution .................................................................64 Bit
DSP processing power ....................................................295 MHz (1.2 billion MAC operations/second)
DSP type .........................................................................Audio signal processor
Signal converter...............................................................A/D: Asahi Kasei
D/A: Analog Devices
Signal-to-noise ratio - digital input ...................................116 dB (A-weighted)
Signal-to-noise ratio - analog input .................................. 108 dB (A-weighted)
Total harmonic distortion (THD+N) - digital input .............< 0.0006%
Total harmonic distortion (THD+N) - analog input ...........< 0.001%
IM distortion (IMD) - digital input......................................< 0.002%
IM distortion (IMD) - analog input ....................................< 0.006%
Crosstalk..........................................................................> 90 dB
Operating voltage ............................................................9.6 - 18 Volts, short drops (up to 5 sec.) down to
6 Volts acceptable
Current draw ....................................................................450 mA
Additional features ........................................................... Control Input, USB, ground lift switch, HEC Slot
Dimensions (H x W x D) ..................................................40 x 177 x 150 mm / 1.58 x 6.97 x 5.91“
The limited warranty comply with legal regulations.
Failures or damages caused by overload or improp­er use are not covered by the warranty. Please return the defective product only with a valid proof of purchase and a detailed malfunction
description.
Technical specications are subject to change! Errors are reserved!
For damages on the vehicle and the device, caused by handling errors of the device, we can’t assume
liability.
All HELIX products are tagged with a E-Certi­cation number and also a CE-Certication mark. Thereby these devices are ceritied for a use inside vehicles inside the European Union (EU).
Technical Data
Warranty Disclaimer
Page 24
Audiotec Fischer GmbH
Gewerbegebiet Lake II · Hünegräben 26 · D-57392 Schmallenberg
Tel.: +49 2972 9788 0 · Fax: +49 2972 9788 88
E-mail: helix@audiotec-scher.com · Internet: www.audiotec-scher.com
Loading...