Heli-Max MD530 2.4GHz RTF/Tx-R, Axe 100 FP 2.4GHz RTF/Tx-R Instruction Manual

Download

Page 1

MD530 2.4GHz RTF/Tx-R

Instruction Manual

™

Page 2

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

ADDITIONAL ITEMS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

KIT INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

KIT CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Tx-R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

BATTERY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CHARGING THE FLIGHT BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

INSTALL THE TRANSMITTER BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . 8

TRANSMITTER CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TURNING THE MODEL ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

FLYING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PARTS LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

INTRODUCTION

Thank you for purchasing the Heli-Max MD-530 Helicopter. We are certain you

will get many hours of enjoyment out of this model. If you should have any

questions or concerns please feel free to contact us at helihotline@hobbico.

com. For the latest technical updates or manual corrections, visit the Heli-Max web site at:

www.helimax-rc.com

Open the “Helicopters” link, and then select the MD-530. If there is new technical

information or changes to this model a “tech notice” box will appear in the upper

left corner of the page.

SAFETY PRECAUTIONS

Follow these safety precautions when operating this or any model

helicopter.

● Keep your face and body as well as all spectators away from the plane of

rotation of the rotors whenever the battery is connected.

● Keep these items away from the rotors: loose clothing, shirt sleeves, ties,

scarfs, long hair or loose objects such as pencils or screwdrivers that may fall out of shirt or jacket pockets into the rotors.

Page 3

● The spinning blades of a model helicopter can cause serious injury. When

choosing a ﬂ ying site for your MD-530, stay clear of buildings, trees and power lines. AVOID ﬂ ying in or near crowded areas. DO NOT ﬂ y close to people, children or pets.

● Maintain a safe pilot-to-helicopter distance while ﬂ ying.

● Your MD-530 should not be considered a toy, but rather a sophisticated,

working model that functions very much like a full-size helicopter. Because of its performance capabilities, the MD-530, if not operated correctly, could possibly cause injury to yourself or spectators and damage to property.

● Do not alter or modify the model, as doing so may result in an unsafe or

unﬂ yable model.

● You must check the operation of the model before every ﬂ ight to insure that

all equipment is operating and that the model has remained structurally sound. Be sure to check linkages or other connectors often and replace them if they show any signs of wear or fatigue.

WARRANTY

Heli-Max® guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any

component parts damaged by use or modiﬁ cation. In no case shall Heli-Max’s

liability exceed the original cost of the purchased kit. Further, Heli-Max reserves the right to change or modify this warranty without notice.

In that Heli-Max has no control over the ﬁ nal assembly or material used for ﬁ nal assembly, no liability shall be assumed nor accepted for any damage resulting from the use by the user of the ﬁ nal user-assembled product. By the act of

using the user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use

of this product, the buyer is advised to return this kit immediately in new

and unused condition to the place of purchase.

To make a warranty claim, send the defective part or item to Hobby Services at

this address.

Hobby Services

3002 N. Apollo Dr., Suite 1 Champaign, IL 61822 USA

Include a letter stating your name, return shipping address, as much contact

information as possible (daytime telephone number, fax number, e-mail address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package the problem will be evaluated as quickly as possible.

Page 4

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING

THE ASSEMBLY AND USE OF THIS MODEL.

ADDITIONAL ITEMS REQUIRED

❏ For Tx-R: Tactic AnyLink and your transmitter

KIT INSPECTION

Before starting assembly, take an inventory of the MD-530 kit. If any parts are

missing, damaged, or defective, contact Product Support. When reporting

defective or missing parts, use the part names exactly as they are written in the

Kit Contents list.

Heli-Max Product Support Ph: (217) 398-8970, ext. 5

3002 N. Apollo Drive, Suite 1 Fax: (217) 398-7721 Champaign, IL 61822 E-mail: helihotline@hobbico.com

KIT CONTENTS

1. Helicopter

2. USB Charger

3. Flight Battery

4. Transmitter (RTF only)

5. AA Batteries (4)

6. Screwdriver

Page 5

Your new MD-530 uses SLT protocol. This means that with the simple addition of

the Tactic Anylink™, you can enjoy your new machine with nearly “any” transmitter.

AnyLink Tx Compatibility Chart (Check Tx-ready.com for updates)

4YF (72MHz), 4YBF, 6EX, 6J, 7C, 8FG, 9C, 10C, 12FG

Futaba

Hitec

Spektrum

Tower Hobbies

Graupner

DX6, DX6i, DX7 DX4e, DX5e, DX7s, DX8, DX10t, DX18 4TH, 6XM 4FM, 6FM

4VF, 5U, 6A, 6DA, 6H, 6YF, 6YG, 7NFK, 8U, 9Z 4YF (2.4 GHz), 12Z, 14MZ, 18MZ Neon, Flash (4sx, 5, 5sx), Focus (4, 6), Laser (4, 6), Optic 5 (72MHz),

Optic 6 (72MHz, 2.4GHz), Eclipse 7 (72MHz), Prism (7, 7X) Aurora 9 Optic 5 (2.4GHz), Optic 6 Sport, Eclipse 7 (2.4GHz) All aircraft transmitters with trainer jack

INCLUDED

TACM0003

TACM0004

TACM0007*

TACM0005*

Required Cable

*Includes a rechargeable 6.6V LiFe battery. LiFe-compatible charger required.

MX-16

WARNING: AnyLink must be in Normal Mapping (1 Beep) when Futaba or Hitec transmitters are used with Tx-R aircraft. If using Spektrum, JR, or Graupner transmitters, AnyLink must be in Alternate Mapping (2 Beeps). (See AnyLink manual.)

This helicopter is unique in that it can work with either an airplane or helicopter

radio. Use the following guide as a setup. Once you feel comfortable, ﬁ ne tune to your liking.

Setup Note: Only adjust the listed parameters and keep all other airplane or

helicopter functions inhibited. If you ﬂ y in heli mode, make sure your swash is

setup for a 90 deg system (H-1).

Reverse N N R N Endpoint 140* each way 140* each way D/R 100/80 100/80 100 Expo pos 20 pos 20 0

Spektrum is a registered trademark of Horizon Hobby, Inc.

*or as high as you can go

Futaba

channel 1 channel 2 channel 3 channel 4

Reverse N N R N Endpoint 140* each way 140* each way D/R 100/80 100/80 100 Expo neg 20 neg 20 0

Spektrum

Page 6

BATTERY PRECAUTIONS

This MD-530 uses a lithium polymer (LiPo) battery. Follow these precautions to

insure safe and trouble free operation.

● Only use the included charger with the included battery.

● Do not attempt to use this charger with NiCd or NiMH battery packs.

● If the battery should become damaged, discard it. Do not attempt to use

a damaged battery.

● Do not leave the charger unattended while charging. Disconnect the

battery and unplug the charger immediately if either becomes hot! However, it is normal for the charger to get warm.

● Disconnect the battery from the charger and carefully move the battery

to a ﬁ reproof location if the battery begins to swell or smoke!

● Never trickle charge.

● Never allow the battery temperature to exceed 140° F [60° C].

● Never disassemble or modify pack wiring in any way or puncture cells.

● Do not allow water, moisture or foreign objects into the charger.

● Do not place the charger or any battery on a ﬂ ammable surface or near

a combustible material while in use.

● Do not charge on a carpet, cluttered workbench, paper, plastic, vinyl,

leather, wood, or inside an R/C model.

● Never charge inside a vehicle.

● Always disconnect the battery and remove the charger from the USB

port when not in use.

● Do not attempt to charge a battery if it is swollen or hot.

● Land your model immediately when the battery begins to lose

power. Recharge the battery before attempting another ﬂ ight.

A dangerous situation can occur when attempting to recharge an

over-discharged battery!

● ALWAYS keep a supply of sand accessible when charging.

Dumping sand on the battery will extinguish the LiPo chemical ﬁ re.

● ALWAYS KEEP OUT OF REACH OF CHILDREN.

Page 7

CHARGING THE FLIGHT BATTERY

WARNING!! The charger supplied with the Heli-Max MD-530 Helicopter contains protective circuitry. If you experience any

difﬁ culties while charging the battery, please disconnect the battery from the charger and unplug the charger from the power source. Allow the battery and charger to rest for two hours as this will allow the charge

protection circuit to reset. If this issue re-occurs during normal use, please contact technical support for further assistance.

❏ Plug the USB charger into your USB

port. The power indicator light on the charger will illuminate red indicating that the charger is ready for use.

❏ Plug the battery into the charger.

The indicator light will start ﬂ ashing,

indicating that the battery is being charged. Once the battery is completely charged, the charge indicator light will stop ﬂ ashing. Disconnect the battery from the charger. Under normal operating conditions, the battery may take up to 60 minutes to recharge.

Charger Indications Power Indicator

Ready to charge battery.

Charging Battery is fully charged. Charger is not powered.

Charger error*

Solid

Flashing

Solid

Off

Flashing

* Once the battery has been disconnected from the charger contact technical support for further assistance.

Page 8

INSTALL THE TRANSMITTER BATTERIES

❏ Carefully remove the battery door and install four AA batteries. Double check the polarity of each battery. Slide the battery cover back into place.

TRANSMITTER CONTROLS

All controls are described with the tail pointing directly toward you. This is the best way to ﬂ y in the beginning since it keeps the control inputs oriented the same direction. Once you start getting comfortable you can work on side

hovering and nose-in.

Page 9

The dual rate switch provides dual

control rates for the cyclic and tail rotor controls. Please use the low rate until you become accustomed to your MD-

530. Change the dual rate using a quick push of the right stick. To adjust the dual

rate, push and “hold” the right stick and move the throttle stick to the desired

percentage. Release the right stick to set.

Moving the cyclic stick

right or left will cause

the helicopter to tilt and

start moving that

direction.

Helicopter Moves Right or Left

Helicopter Moves Right or LeftHelicopter Moves Right or Left

Moving the cyclic stick

forward or backward

will cause the helicopter

to tilt and start moving

that direction.

Helicopter Moves Backwards or Forwards

Page 10

Moving the throttle

stick up or down will

cause the helicopter to

climb or descend.

Helicopter Climbs or Descends

Helicopter Climbs or DescendsHelicopter Climbs or Descends

Moving the tail rotor

stick left or right will

cause the helicopter

nose to rotate in that

direction.

Nose Rotates Left or Right

Nose Rotates Left or RightNose Rotates Left or Right

TURNING THE MODEL ON

❏ Move the throttle stick to the lowest position and then turn the transmitter on.

Page 11

Electric motors are very dangerous. Do not work on the model while the ﬂ ight battery is plugged in as interference may cause the main rotor blades to spin, possibly causing injury to yourself.

❏ Slide the flight battery into the

battery compartment.

NOTE: The battery will only install one way. The helicopter will be “ON” at this point.

Your helicopter has a safe start feature built in that prevents the motor from activating unless the throttle stick has been lowered to the lowest position. If the motor won’t run and turn the main blades, please make sure the throttle stick is all the way down and leave it there for a couple of seconds. Then try moving the stick up slowly.

FLYING

The Heli-Max MD-530 is a lightweight helicopter. Taking that into consideration,

you should only ﬂ y indoors or in calm winds less than 5mph. It should be ﬂ own

in a large area of at least 75 feet [15.25m] square with no obstacles.

Crashing

If you have operated radio control models in the past, then you probably already realize that it is not a matter of “if” you are going to crash, it is a matter of “when” you are going to crash. Once you realize the model is going to collide with

something or crash into the ground, you should always bring the throttle stick all the way down to stop the main rotor blades from rotating. If you can remember to do this, chances are you will not damage the helicopter in the crash. The

main rotor blades carry a lot of RPM and inertia during ﬂ ight. Cutting the power to the main rotor blades will prevent most of the crash damage.

Takeoff

Slowly add power, observe the model and make all of the necessary corrections to keep the model level. You will ﬁ nd that model helicopters never allow you to return the sticks to center. You just need to position the stick as needed to

maintain a steady hover. With the TAGS system, no trimming is needed.

Page 12

Hovering

Once the helicopter is up in the air, try to hold the helicopter in one spot. If this

is your ﬁ rst model helicopter, it will require some practice. Wind or air currents

have a big effect on the stability of the helicopter. Be patient and try to anticipate where the helicopter will move.

Landing

Level the helicopter into a steady hover and slowly decrease power until the

helicopter settles onto the ground.

Basic Maneuvers

Slow Pirouettes – Add a small amount of tail rotor (left or right) and try rotating the helicopter slightly sideways and see if you can hold it there. If you feel

uncomfortable, then bring the tail back toward you. Once you start getting

comfortable, try moving the helicopter to the side. Then turn back and ﬂ y back to the other side in straight lines. Then work into rotating the helicopter around 360°, which is called a pirouette. The helicopter can drift during these so make

sure you have plenty of room when you ﬁ rst start practicing.

Nose-in Hovering – After pirouettes it’s time to move on to nose-in hovering.

Take off and climb to 10 feet [3m]. Practice half pirouettes from tail in to nose-

in hovering and try to lengthen the delay in between. This will give you a little

practice nose-in and still give you a chance to get out of trouble. As your skills

improve you’ll remain nose-in for longer periods of time.

Forward Flight – Now it’s time to work into basic forward ﬂ ight. Just take the

basic hovering maneuvers listed above and slowly ﬂ y out farther and faster and always bring the helicopter back after one pass. Practice controlled slow ﬂ ight in close as well. The more time you spend practicing here the easier things will be later on.

GOOD LUCK AND GREAT FLYING!

ORDERING PARTS

Replacement parts for the Heli-Max MD-530 are available using the order

numbers in the Replacement Parts List that follows. The fastest, most economical service can be provided by your hobby dealer.

To locate a hobby dealer, visit the Heli-Max web site at www.helimax-rc.com.

Choose “Where to Buy” at the bottom of the page.

Parts may also be ordered directly from Hobby Services by calling (217) 3980007, or via facsimile at (217) 398-7721, but full retail prices and shipping and

handling charges will apply. Illinois and Nevada residents will also be charged

Page 13

sales tax. If ordering via fax, include a Visa® or MasterCard® number and expiration date for payment.

Mail parts orders Hobby Services and payments by 3002 N. Apollo Drive, Suite 1 personal check to: Champaign, IL 61822

Be certain to specify the order number exactly as listed in the Replacement Parts List. Payment by credit card or personal check only; no C.O.D.

If additional assistance is required for any reason contact Product Support by e-mail at helihotline@hobbico.com, or by telephone at (217) 398-8970.

PARTS LIST

Key No. Part No. Part Name

1 HMXE2105 Main Blade 2 HMXE2135 Blade Grips 3 HMXE2160 Screw Set (All) 4 HMXE2137 Feathering Shaft 5 HMXE2138 Blade Grip Spacers 6 HMXE2139 Rubber Dampeners 7 HMXE2140 Rotor Head 8 HMXE2141 Rotor Head Linkage 9 HMXE2142 Main Shaft 10 HMXE2143 Swashplate 11 HMXE2109 Main shaft collar 12 HMXE2144 Bearing Set 13 HMXE2163 Main Frame 14 HMXG8028 Main Motor 15 HMXM2039 TAGs 3-1 SLT Control Board 16 HMXE2162 Servo Linkages 17 HMXE2147 Main Gear 18 HMXE2165 LED Light 19 HMXE2164 Canopy (front with LED) 20 HMXE2150 Servo Arms with metal ball joint 19/21 HMXE2168 Fuselage 21 HMXE2161 Aft Fuselage 22 HMXM2037 Servo 23 HMXG8030 Tail Motor with boom assembly 24 HMXE2152 Tail Rotor Blade 25 HMXP1007 1S LiPo Battery 26 HMXE2167 Landing Skid 27 HMXE2166 Battery Frame HMXJ2024 410 SLT Transmitter HMXP2021 1S USB Charger

Page 14

MD530 Fuselage

3 21

EXPLODED VIEW

Page 15

MD530

Rotor

Head

MD530

Frame

Page 16

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.

(1) This device may not cause harmful interference. (2) This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT .

FCC REQUIREMENT

CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

Instructions for Disposal of Waste Equipment by Private Users in the European Union: This symbol on the product or its packaging indicates this product must not

be disposed of with other household waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or location where you purchased the product.

Declaration of Conformity:

Product: Heli-Max TX410 2.4GHz 4-Channel Tx Rx Item number: HMXJ2024 TX410, Equipment class: 1

TX410 transmitter: The objects of the declaration described here are in conformity with the requirements of the specifications listed below, following the provisions of the European 2006/95/EC Low Voltage Directive:

EN 60950-1:2006 Safety The objects of the declaration described here are in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1995/5/EC:

ETSI EN 300 328 V1.7.1 Technical requirements for radio equipment ETSI EN 301 489-1 V1.8.1, 301 489-17 V1.3.2 General EMC requirements for radio equipment

Hobbico, Inc. 2904 Research Road Champaign, IL USA 61826

The associated regulatory agencies of the following countries recognize the noted certifications to this product as authorized for sale and use.

UK DE DK BG SE FI GR

EE LV LT PL CZ SK HU

RO SI AT IT ES PT IE

NL LU MT CY

2200