Heli-Max AXE100CP Instruction Manual

Entire Contents © 2012 Hobbico®, Inc. HMXE0820 HMXE0821

NOTICE

Instruction Manual

®

The instruction manual, warranties and other associated documentation are subject
to change without notice. Hobbico assumes no responsibility for inadvertent errors
in this manual.

Heli-Max products are to be used by ages 14 and over.

™

2

®

INTRODUCTION

INTRODUCTION

Thank you for purchasing the Heli-Max AXE 100 CP Helicopter. We are certain

you will get many hours of enjoyment out of this model. If you should have
any questions or concerns please feel free to contact us at: helihotline@

hobbico.com.

For the latest technical updates or manual corrections to the AXE 100 CP visit
the Heli-Max web site at www.helimax-rc.com. Open the “Helicopters” link, and
then select the AXE 100 CP. If there is new technical information or changes to
this model a “tech notice” box will appear in the upper left corner of the page.

®

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS

Failure to follow these safety precautions may result in injury
to yourself and others.

● Keep your face and body as well as all spectators away from the plane of
rotation of the rotors whenever the battery is connected. Keep these items
away from the rotors: loose clothing, shirt sleeves, ties, scarfs, long hair or
loose objects such as pencils or screwdrivers that may fall out of shirt or jacket
pockets into the rotors. The spinning blades of a model helicopter can cause
serious injury. When choosing a flying site for your AXE 100 CP, stay clear of
buildings, trees and power lines. AVOID flying in or near crowded areas. DO
NOT fly close to people or pets. Maintain a safe pilot-to-helicopter distance
while flying.

● Your AXE 100 CP should not be considered a toy, but rather a sophisticated,
working model that functions very much like a full-size helicopter. Because of
its performance capabilities, the AXE 100 CP, if not operated correctly, could
possibly cause injury to you or spectators and damage to property.

● Do not alter or modify the model, as doing so may result in an unsafe or
un-flyable model.

● When and if repairing you must correctly install all components so that the model
operates correctly on the ground and in the air. Please check the operation of
the model before every flight to insure that all equipment is operating and that
the model has remained structurally sound. Be sure to check linkages or other
connectors often and replace them if they show any signs of wear or fatigue.

3

Battery warnings and usage guidelines: Please read and
understand the following regarding the usage of Li-Po batteries.

Through the use of the included Li-Po battery you have assumed all risk and

responsibility regarding a Li-Po battery and its use.

If your battery begins to swell or “puff” during charge or discharge, stop using it
and discard. Call or contact Hobby Services 217-398-0007 to learn the proper
way to safely discard your Li-Po cells.

● Only use the included charger with the included battery.

● Do not attempt to use included charger with NiCd or NiMH battery packs.

● If the battery should become damaged, discard it.

● Do not leave the charger unattended while charging.

● Disconnect the battery and remove input power from the charger immediately

if either becomes hot! However, it is normal for the charger to get warm.

● Never allow the battery temperature to exceed 150° F [65° C].

● Never disassemble or modify pack wiring in any way or puncture cells.

● Do not allow water, moisture or foreign objects into the charger.

● Do not block the air intake holes, which could cause the charger to overheat.

● Do not place the charger or any battery on a fl ammable surface or near a

combustible material while in use.

● Never charge inside a vehicle.

● Always disconnect the battery from the charger and the power supply from

the charger when not in use.

● Do not attempt to charge a battery if it is swollen or hot.

● It’s best to store your batteries at room temperature

● ALWAYS KEEP OUT OF REACH OF CHILDREN.

NOTE: Heli-Max AXE battery packs are not cross
compatible with Heli-Max NOVUS brand products.

4

®

WARRANTY

WARRANTY

Heli-Max guarantees this kit to be free from defects in both material and
workmanship at the date of purchase. This warranty does not cover any component

parts damaged by use or modification. In no case shall Heli-Max’s liability
exceed the original cost of the purchased kit. Further, Heli-Max reserves the

right to change or modify this warranty without notice. In that Heli-Max has no

control over the final assembly or material used for final assembly, no liability
shall be assumed nor accepted for any damage resulting from the use by the
user of the final user-assembled product. By the act of using the user assembled
product, the user accepts all resulting liability. If the buyer is not prepared to

accept the liability associated with the use of this product, the buyer is
advised to return this kit immediately in new and unused condition to the
place of purchase.

To make a warranty claim, Hobby Services 217-398-0007
send the defective part or 3002 N. Apollo Dr., Suite 1
item to Hobby Services Champaign, IL 61822
at this address. USA

Include a letter stating your name, return shipping address, as much contact

information as possible (daytime telephone number, fax number, e-mail address),
a detailed description of the problem and a photocopy of the purchase receipt.
Upon receipt of the package the problem will be evaluated as quickly as possible.

®

CONTENTS

CONTENTS

Required: 8 AA batteries

TX 610 Transmitter (W/TX610 manual)
AXE 100 CP Helicopter
(2) 200mAh Li-Po Flight Battery
Li-Po Battery Charger
Screwdriver
Extra Blade Set
Extra Rotor Linkage Set

5

®

OPERATIONAL WARNINGS

OPERATIONAL WARNINGS

● Please allow a 10 minute cool down period after each flight so the motor

controller and motor can cool down. Failure to do so may cause loss of control
due to the controller overheating and shutting down.

● Please inspect the main rotor blades and blade screws before each flight for

nicks or loose components. If any damage is found or if the blades have been
crashed, please replace the blades before flying the model again.

● The ESC does have a soft cut function that will reduce the power output to

protect the flight battery. Toward the end of a flight, if you notice a slight power
reduction, land the model immediately and recharge the battery. The flight
time of the AXE 100 CP can be as long as 6 minutes but this will vary depending
on your flying style.

CAUTION! After a crash you must inspect all plastic parts on the
helicopter for damage before flying the model again.

®

TRANSMITTER

TRANSMITTER

Please read the transmitter manual included with your helicopter to learn more
about how to use and adjust your TX610.

TRANSMITTER FUNCTIONS AND SWITCHES

The Throttle Hold Switch

(HOLD/FLAP) is used to
disable the power output
of the motor but has no
effect on the other controls.

The Throttle Hold Function

was originally intended for
autorotation landings (off
power descent to landing);
this maneuver is really
not possible with a motor
driven tail.

In addition to autorotation
the throttle hold function can

be used as a safety switch while handling the model since it disables power to
the motor. Turn the transmitter on and set the Throttle Hold Switch to the on

6

position. Now you can safely connect the flight battery without having to worry
about inadvertently moving the throttle stick. Once you place the model on the

ground, verify that the idle up switch is off and the throttle stick has been moved
to its lowest position, then simply turn the throttle hold off. The model is now
ready to fly. Another use for the throttle hold function is to disable the motor

before a crash without having to drop the collective stick (possibly forcing the

model into the ground). Disabling the motor before a crash can prevent a lot
of damage.

The UP-1 function is enabled
and ready to use. The UP-1

switch (UP-1/GEAR)
function is used for
aerobatics and 3D flight. If
you are a beginner to
aerobatics remember this

switch sets the motor speed
(see your TX610 manual for

details) while still allowing

positive and negative pitch

control. This means pulling
the throttle stick back WILL
NOT decrease the power to
the motor but rather add

power. Hence it’s a good

idea to learn to use the

Throttle Hold Switch when

you feel a crash is imminent!

7

STICK CONTROLS

Throttle/Collective

Tail (rudder)

Left and right cyclic

Forward and back cyclic

It’s also important to know that your TX610 transmitter is capable of a system
reset. (See how this is done in the TX610 Manual) If you decide to do a system
reset, the factory setup numbers to the Heli-Max AXE 100 CP are listed here.

Below are the factory setup parameters for your AXE 100 CP Helicopter.

TX610 1 2 3 4 5 6

Servo Reverse NOR NOR REV NOR NOR NOR
Dual Rates 80/100 80/100 80/100
Exponential -20 -20 0
Sub Trims 0 0 0
Normal Throttle 0 45 75 92 100
Normal Pitch 40 45 55 70 75
UP-1 Throttle DIAL
UP-1 PITCH 30 42 55 65 75
Gyro 35 NON HH 75 HH
Swashplate Type 90deg

8

®

GETTING THE MODEL READY TO FLY

GETTING THE MODEL READY TO FLY

INSTALL BATTERIES IN THE TRANSMITTER

Remove the battery cover from the back
of the transmitter and install eight “AA”

batteries into the transmitter. Double-

check the polarity of each battery before
replacing the battery cover.

CHARGE THE FLIGHT BATTERY

Plug the wall power supply into any 110V

standard outlet. Plug the remaining
4mm plug into the side of the charger

box. The center front panel LED will light

letting you know the charger has power.