Heitronic 36006, 36007 Installation and operating instructions

GB Installation and operating instructions

Heitronic

®

LED outside wall light "KUBUS"
Art. No. 36006, 36007

Many thanks for deciding to buy our lights.
Our LED light is made out of sturdy, high value materials and will provide you with quality lighting. The
light can be used both indoors and also outdoors.

Please read through installation and operation instructions carefully and keep these in a safe
place for future reference.

We do not accept liability for damage to persons or property caused by non observation of the
instructions, improper handling or for unauthorized changes made to the product.

Package contents:

 1 LED light
 Installation and operating instructions

Technical data:

Article Connection

36006

36007

230 V 50 Hz

230 V 50 Hz

36 LED illuminants total max. 3,6W
cannot be changed
72 LED illuminants total max. 7,2W
cannot be changed

Protection
type

IP 44 I

IP 44 I

Protection
Class

Safety and warning notes:

 Do not look directly into the LED - especially for longer periods of time - without protecting

your eyes. A LED beam should not be directed into other people's eyes.

 Make sure, before using the light that it has not been damaged during transportation. Do not

operate the light if the cable or the electrical parts are damaged. Repairs may only be done by
a specialist electrician.

 Keep packaging materials well away from children and pets. Danger of suffocation!
 Be careful. The packaging contains small parts which can be swallowed by children.
 Do not leave children unattended in the area of the lights or other electrical appliances.
 Never expose the lights to a direct jet of water garden hose or high pressure cleaner, for

example) and never immerse the lights into water or other liquids !

 The illuminant is hot when it is in operation. The outer lamp housing will also be hot. Do not

touch the light with your bare hands when it is being operated.

 The entire product must neither be changed nor converted. Changes made to the light lead to

annulment of the guarantee (warranty).

Care and servicing:

 You must make sure that the power supply is disconnected before cleaning.
 Use a dry, or slightly damp cloth for cleaning.
 Never use chemicals, inflammable cleaners or abrasives for cleaning. These can damage the

surface and / or the insulations of the light.

Disposal:

 Old electronic equipment must be brought to public connection points and must not be

disposed of as household waste.

H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein

Installation instruction Art. No. 36006, 36007 Page 1 of 2 Status 11.2011

Installation:

Heitronic

®

 This product may only be installed by a qualified specialist electrician.
 Make sure that the connection values of your building installation for the power supply to the

light comply with the data stated on the name plate of this light.

 Before the installation is done, the connection lines to the building must be switched free from

voltage and protected against being switch on again. Take the appropriate automatic circuit
breakers out of the junction box in the building.

 Protection of the wall light with a default current circuit breaker is recommended when it is

being used outdoors.

 Make sure that no water can collect at the place where the light is fastened.
 Decide on the location where installation has to take place. The lights are suitable for surface

mounting. Mount the brackets for surface mounting. Make sure that the base and the
fastening material are suitable and the weight of the lights can be supported permanently and
reliably.

 Make sure that the base is suitable to support the weight of the light permanently and reliably.
 Now connect the connection lines at building installation to the screw terminals of the light.

Connect up the yellow-green ground wire first of all and then the other two lines. The brown
(or black) cable is usually the phase conductor, connect this to the terminal marked with an
"L". The blue conductor must be connected to the terminal marked with an "N".

 Do not bend the cable, make sure that the cable and the plug are free from strain and

rotational forces. Protect all cables and insulations from possible damage.

 Make sure you have a stable and reliable fastening.
 Switch on the circuit breakers of the junction box in the building again.
 The name plate must not be removed.

H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein

Installation instruction Art. No. 36006, 36007 Page 2 of 2 Status 11.2011