Heiman SMOKI NS-626PHS, SMOKI HM-626PHS User Manual

SMOKE ALARM Mode:HM-626PHS Ten-year Battery Operated Photoelectric Smoke Alarm Mode:NS-626PHS

M213-4 OVer1.0

1138b /02

083 2-CPR -F109 1 Standards tested to: EN14604:2005/AC:2008

Distributor:Newtonstein Corp. 19C Trolley Square, Wilmington, Newcastle, Delaware, 19806, USA. Manufactured under License from H. Technologies Ltd. this is a certified and audited product as per regulations.

IMPORTANT! PLEASE READ CAREFULLY AND SAVE.

This user's manual contains important information about your Smoke Alarm's operation. If you are installing this Smoke Alarm for use by others, you must leave this manual—or a copy of it—with the end user.

Photoelectric alarms are generally more effective at detecting slow, smoldering fires that smolder for hours before bursting into flame. Sources of these fires may include cigarettes burning in couches or bedding. Ionization alarms are generally more effective at detecting fast, flaming fires that consume combustible materials rapidly and spread quickly. Sources of these fires may include flammable liquids or paper burning in a waste container. However, both types of alarms provide adequate detection of both types of fires. If you desire the earliest detection of both smoldering fires and fast flaming fires, you should install smoke alarms that combine both photoelectric and ionization sensing technologies in one unit.

PACKING LIST

PART NAME

Smoke alarm Mounting bracket

Screw

Anchor plug

Manual

QUANTITY

1 Piece 1 Piece 2 Pieces

2 Pieces 1 Piece

PACKING LIST

Smoke Alarm

Screw

Mounting Br ac ket

Anchor plug

Magnetic Pa ne l

Manual

CONTENTS

1. SUPERIOR FEATURES

2. IMPORTANT SAFETY INFORMATION … … … … 02

3. WHERE TO LOCATE………………………………05

4. LOCATIONS TO AVOID……………………………10

5. HOW TO INSTALL …………………………………11

6. LED INDICATORS AND HORN PATTERNS ……15

7. FALSE ALARM CONTROL ……… ………………16

8. TESTING THE SMOKE ALARM …… …………… 17

9. MAINTENANCE AND CLEANING ………………19

10. PRACTICE FIRE SAFETY… …… …… …………21

11. WHAT TO DO IN CASE OF A FIRE ………… …22

12. TROUBLESHOOTING ……………………………23

13. LIMITATIONS OF SMOKE ALARMS ……………24

14. LIMITED WARRANTY ……………………………29

……………………………01

1. SUPERIOR FEATURES

●Battery Operated Long-life lithium-ion battery sealed in the alarm to lengthen

its lifetime to 10 years in standby condition.

●Operating Light (LED)

Flashes approximately every 53 seconds confirming unit is

powered.

●Low Battery Warning

Alarm beeps every 40 seconds when the battery needs replacing.

●Alarm Pause (Hush mode)

Silence your smoke alarm by momentarily pressing the test button when non-emergency smoke (e.g. steam), causes nuisance alarms. The red light flashes every 10 seconds to remind you that the smoke alarm has been silenced. The alarm will automatically reset after 15 minutes.

Sensitivity Test Button

●

Test the sensitivity, circuitry, batteries, horn.

●Loud 85 Decibel Piezo Electric Alarm Automatically resets when hazardous condition has passed.

●Easy Installation

Fixings supplied.

2.IMPORTANT SAFETY INFORMATION

WARNING!

PLEASE READ AND SAVE THESE INSTRUCTIONS.

●DO NOT remove or disconnect battery to quiet unwanted alarms. This will remove your protection. Open windows or

fan the air around smoke alarm to silence it.

● The test button accurately tests all smoke alarm functions. DO NOT use any other test method. Test smoke alarm

weekly to ensure proper operation.

● This smoke alarm should be installed only by a licensed, qualified electrician. Observe and follow all local and national electrical and building codes for installation.

This smoke alarm IS NOT designed to be the PRIMARY

●

protection for buildings that require complete fire alarm systems. Buildings of this type include hotels, motels, dormitories, hospitals, nursing homes, and group homes. This is true even if they were once single family homes. However, this smoke alarm MAY be used inside individual rooms as SUPPLEMENTAL protection.

●Install a smoke alarm in every room and on every level of the home. Smoke may not reach the smoke alarm for many reasons. For example, if a fire starts in a remote part of the home, on another level, in a chimney, wall, roof, or on the other side of a closed door, smoke may not reach the smoke alarm in time to alert household members. A smoke alarm will not promptly detect a fire EXCEPT in the area or room in which it is installed.

●Smoke alarms may not alert every household member every time. The alarm horn is loud in order to alert individuals to a potentia l dange r. However, there ma y be limiting circumstances where a household member may not hear the alarm (i.e., outdoor or indoor noise, sound sleepers, drug or alcohol usage, the hard of hearing, etc.).

If you suspect that this smoke alarm may not alert a

household member, install and maintain specialty smoke alarms. Household members must hear the alarm's warning sound and quickly respond to it to reduce the risk of damage, injury, or death that may result from fire. If a household member is hard of hearing, install special smoke alarms with lights or vibrating devices to alert occupants.

●Smoke alarms can sound their alarms only when they detect smoke. Smoke alarms detect combustion particles in the air. They do not sense heat, flame, or gas. This smoke alarm is designed to give audible warning of a developing fire. However, many fires are fast-burning, explosive, or intentional. Others are caused by carelessness or safety hazards. Smoke may not reach the smoke alarm QUICKLY ENOUGH to ensure safe escape.

● Smoke alarms have limitations. This smoke alarm is not foolproof and is not warranted to protect lives or property from fire. Smoke alarms are not a substitute for insurance. Homeowners and renters should insure their lives and property. In addition, it is possible for the smoke alarm to fail at any time. For this reason, you must test the smoke alarm weekly and replace every 10 years.

3. WHERE TO LOCATE

3.1 As a minimum, smoke alarms should be located between sleeping areas and potential sources of fire such as living rooms and kitchens. In single story homes with one sleeping area, a smoke alarm should be installed in the hallway, as close as possible to the living accommodation. To ensure audibility in bedrooms, no smoke alarm should be further away than 3m from any bedroom door. It may be necessary to install more than one smoke alarm, particularly the hallway is more than 15m long. In single story homes with two separate sleeping areas, a minimum of two smoke alarms is required, one outside each sleeping area. In multilevel or split level homes, as a minimum a smoke alarm should be installed on the ground floor between the staircase and any rooms in which a fire might start and on each story in circulation areas which form part of escape route (normally hallways and landings).

3.2 Additional alarms should be installed in bedrooms in anticipation of fires originating here, caused by faulty wiring, lights, appliances, smokers or other hazards.

3.3 For best protection, smoke alarms should be installed in every room in your home, apart from those listed in the Section 4 LOCATIONS TO AVOID. Heat alarms should be used in kitchens, boiler rooms, laundry rooms, garages and such like, where smoke alarms would be unsuitable.

3.4 Install smoke alarms in circulation areas at a distance no greater than 7.5m from the farthest wall, no greater than

7.5m from a door to any room in which a fire might start and no greater than 7.5m from the next smoke alarm.

3.5 As it is impossible to predict the source of a fire, the best location for an alarm is usually the center of a room or hallway. If it is necessary to place a smoke alarm on a wall, always locate the detection element of the alarm 150mm to 300mm (6 to 12 inches) below the ceiling and the bottom of the alarm above the level of doors and other openings.

3.6 In rooms with simple sloped, peaked or gabled ceilings, install smoke alarms on the ceiling 900mm (3 feet) from the highest point of the ceiling. “Dead air” at the peak of a ceiling may prevent the smoke from reaching the alarm in time to provide an early warning.

Dead air area

15 c m

Center

15 c m

3.7 Read Section 4 LOCATIONS TO AVOID and Section 13 LIMITATIONS OF SMOKE ALARMS in this manual.

CAUTION: Research indicates that substantial increases in

warning time can be obtained with each properly installed, additional alarm. It is strongly recommended that advice in 3.3 above be followed to ensure maximum protection.

Single Story, one sleeping area

DINING ROOM

LIVING ROOM

KITCHEN

Single Story, more than one sleeping areas

DINING

TV ROOM

BEDROOM

ROOM

LIVING ROOM

BEDROOM BEDROOM

BEDROOM

KITCHEN

BEDROOM

Two Story dwelling

HALL

LIVING ROOM

BEDROOMBEDROOM

KITCHEN

FINISHED BASEMENT

Smoke alarms for limited protection Additional smoke alarms for better coverage Heat alarms

IMPORTANT:

These alarms are intended to primarily for single-occupancy private dwellings. For use in other applications the manufacturer's advice must be sought.

4. LOCATIONS TO AVOID

DO NOT locate smoke alarms :

4.1 In turbulent air from fans, heaters, doors, windows, etc., which could draw smoke away from the alarm.

4.2 In high humidity area such as bathrooms and shower rooms, or where the temperature exceeds 39˚C ( 100˚F) or falls below 5˚C ( 40˚F), as high humidity can trigger nuisance alarm.

4.3 A t the peal of an “A” frame ceiling. “Dead air” at the top may prevent smoke from reaching the alarm in time to provide early warning.

4.4 Less than 300mm (12 inches) from the wall when mounted on the ceiling.

4.5 In insect-infested areas.T iny insects may affect performance.

4.6 In kitchens, boiler rooms, laundry rooms, garages. Combustion particles from cooking or car exhaust and dust and moisture could trigger a nuisance alarm.

4.7 In very dusty or dirty areas. Dirt and dust can build up and impair performance.

4.8 Within 300mm (12 inches) of light fittings or room corners.

4.9 In locations which would make routine testing or maintenance hazardous (e.g. over a stairwell).

4.10 On poorly insulated walls or ceilings.

4.11 Near objects such as ceiling decorations which might impede the path of smoke to the alarm.

4.12 Within 1500mm (5 feet) of fluorescent light fittings.

5. HOW TO INSTALL

5.1 Using needle-nose pliers or a utility knife, detach one locking pin from the mounting bracket to separate the alarm from the mounting bracket.

5.2 Draw a horizontal or vertical line 6 inches (10 cm) long on the area of ceilings or walls where this smoke alarm is intended to locate (see Section 3 WHERE TO LOCATE).

5.3 Locate the mounting bracket in your chosen position. Align the two longest mounting slots with the line. Draw a mark in the center of each slot.

Mounting slot

5.4 Drill the holes at the marks with a 3/16-inch (5mm) drill.

5.5 Insert the anchor plugs and screw the mounting bracket to the chosen position. DO NOT OVER-TIGHT THE SCREWS, this will distort the mounting bracket.

5.6 Attach the alarm to the mounting bracket and turn clockwise to lock into place.

5.7 To engage tamper-resist feature, insert the locking pin into the notch on edge of smoke alarm after alarm is properly positioned.

NOTE: Only when the smoke alarm has attached to the

mounting bracket can it be activated.

5.8 Test the smoke alarm. See Section 8 TESTING THE SMOKE ALARM.

6.LED INDICATORS AND HORN PATTERNS

CONDITION

Normal Operation

Test Condition

Alarm Condition

Hush Mode

Low Battery

Malfunction

LED

Red LED flashes every 53 seconds.

Red LED flashes rapidly.

Red LED flashes every 10 seconds.

Red LED flashes every 40 seconds.

HORN

None

Short quick beeps

None

One beep every 40 seconds

Two beeps every 40 seconds

7.FALSE ALARM CONTROL

The alarm features a False Alarm Control that, when activated, silences unwanted alarms for up to 15 minutes. To use the False Alarm Control: Press and release the test button during an unwanted alarm to silence the alarm horn. This means the smoke alarm is in False Alarm Control. If the smoke alarm does not go into False Alarm Control and continues to sound its loud alarm horn or if it initially goes into False Alarm Control then resounds the alarm, the smoke is too heavy and could be a possibly dangerous situation— take emergency action.

8.TESTING THE SMOKE ALARM

WARNING!

Test each smoke alarm to be sure it is installed correctly and operating properly.

●The test button accurately tests all functions. DO NOT use an open flame to test this smoke alarm. You may ignite and damage the smoke alarm or your home.

● Test smoke alarms weekly and upon returning from vacation or when no one has been in the household for several days.

●Stand at arm's length from the smoke alarm when testing. The alarm horn is loud to alert you to an emergency and can be harmful to hearing.

8.1 Press and release the test button to test the alarm. The alarm will sound loud short beeps. The alarm may stop sounding once releasing the test button.

8.2 If smoke alarm does not sound, check whether the alarm is properly attached to the mounting bracket.

NOTE: REPLACE OR RETURN THE ALARM IF THE TEST

FUNCTION DOES NOT OPERATE PROPERLY AFTER FOLLOWING THE PROCEDURES OUTLINED ABOVE.

DANGER: If alarm horn sounds, and smoke alarm is not being tested, the smoke alarm is sensing smoke.

THE SOUND OF THE ALARM HORN REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.

9.MAINTENANCE AND CLEANING

This unit has been designed to be as maintenance-free as possible, but there are a few simple things you must do to keep it working properly:

9.1 Test it at least once a week.

9.2 Clean the smoke alarm at least once a month; gently

vacuum the outside of the smoke alarm using your household vacuum's soft brush. Test the smoke alarm. Never use water, cleaners or solvents since they may damage the unit.

9.3 If the smoke alarm becomes contaminated by excessive dirt,

dust and/or grime, and cannot be cleaned to avoid unwanted

alarms, replace the unit immediately.

9.4 Relocate the unit if it sounds frequent unwanted alarms. See

Section 4 LOCATIONS TO AVOID for details.

9.5 When the battery back-up becomes weak, the smoke alarm

will sound one beep every 40 seconds (the low battery

warning). You should replace the alarm immediately to

continue your protection.

10.PRACTICE FIRE SAFETY

If the smoke alarm sounds its alarm horn, and you have not pushed the test button, it is warning of a dangerous situation. Your immediate response is necessary. To prepare for such occurrences, develop family escape plans, discuss them with ALL household members, and practice them regularly.

10.1 Expose everyone to the sound of a smoke alarm and explain what the sound means.

10.2 Determine TWO exits from each room and an escape route

to the outside from each exit.

10.3 Teach all household members to touch the door and use an

alternate exit if the door is hot. INSTRUCT THEM NOT TO

OPEN THE DOOR IF THE DOOR IS HOT.

10.4 Teach household members to crawl along the floor to stay

below dangerous smoke, fumes, and gases.

10.5 Determine a safe meeting place for all members outside the

building.

11. WHAT TO DO IN CASE OF A FIRE

11.1 Don't panic; stay calm.

11.2 Leave the building as quickly as possible. Touch doors to

feel if they are hot before opening them. Use an alternate exit if necessary. Crawl along the floor, and DO NOT stop

to collect anything.

11.3 Meet at a pre-arranged meeting place outside the building.

11.4 Call the fire department from OUTSIDE the building.

11.5 DO NOT GO BACK INSIDE A BURNING BUILDING. Wait

for the fire department to arrive.

NOTE: These guidelines will assist you in the event of a fire.

However, to reduce the chance that fires will start, practice fire

safety rules and prevent hazardous situations.

12.TROUBLESHOOTING

PROBLEM

Smoke alarm does not respond.

Red LED flashes and the alarm sounds one beep every 40 seconds.

Red LED flashes and the alarm sounds two beeps every 40 seconds.

Smoke alarm sounds unwanted alarms intermittently or when residents are cooking, taking showers, etc.

SOLUTION

Please check whether the alarm is properly attached to the mounting bracket.

Battery is low – REPLACE IT IMMEDIATELY!

The alarm is malfunctioning. Please clean your smoke alarm . Or REPLACE OR RETURN FOR REPAIR IMMEDIATELY!

1. Clean smoke alarm. See Section 9 MAINTENANCE AND CLEANING.

2. Hire an electrician to move smoke

alarm to a new location. See Section 3 WHERE TO LOCATE.

13.LIMITATIONS OF SMOKE ALARMS

Smoke Alarms have played a key role in reducing deaths resulting from home fires worldwide. However, like any warning device, Smoke Alarms can only work if they are properly located, installed, and maintained, and if smoke reaches the Alarms. They are not foolproof.

13.1 Smoke alarms may not waken all individuals.

Practice the escape plan at least twice a year, making sure that everyone is involved – from kids to grandparents. Allow children to master fire escape planning and practice before holding a fire drill at night when they are sleeping. If children or others do not readily waken to the sound of the smoke alarm, or if there are infants or family members with mobility limitations, make sure that someone is assigned to

assist them in fire drill and in the event of an emergency. It is recommended that you hold a fire drill while family members are sleeping in order to determine their response to the sound of the smoke alarm while sleeping and to determine whether they may need assistance in the event of an emergency.

13.2 Smoke alarms cannot work without power.

Battery operated units cannot work if the batteries are missing, disconnected or dead, if the wrong type of batteries are used, or if the batteries are not installed correctly. AC units cannot work if the AC power is cut off for any reason (open fuse or circuit breaker , failure along a power line or at a power station, electrical fire that burns the electrical wires, etc.). If you are concerned about the limitations of battery or AC power, install both types of units.

13.3 Smoke alarms cannot detect fires if the smoke does not reach the alarms.

Smoke from fires in chimneys or walls, on roofs, or on the other side of closed doors may not reach the sensing chamber and set off the Alarm. That is why one unit should be i n stalled in s i d e e a c h b e d r o o m or sl e e p i n g area—especially if bedroom or sleeping area doors are closed at night—and in the hallway between them.

13.4 Smoke alarms may not detect fire on another

floor or a rea of the dwelling.

For example, a stand- alone unit on the second flo or

may not detect smoke f rom a basement fire until the fire spreads. This may not gi ve you enough time to escape safely. That is why recommended minimum protection is at least one unit in every sleeping are a, and every bedroom on every level of your dwelling. Even with a unit on every floor, stand-alone units may not provide as much protection as interconnected units, especially if the fire starts in a remote area. S o me s af e ty ex p e rt s r e co m me n d i n st a ll i ng interconnected AC powered un its with battery back-up (see “About Smoke Alarm s”) or profess ional fire detection systems, so if one unit senses smoke, al l units alarm. Interconnected units may provide earlier warning than st and-alone units since all units alarm when one detects smoke.

+ 135 hidden pages

Heiman SMOKI NS-626PHS, SMOKI HM-626PHS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual