Hehui Safety Manufacture Y6600 Users Manual

mp3/ preview

Bluetooth stereo headset user guide

Bluetooth Introduction:

The Bluetooth headset is a portable headset solution based on Bluetooth wireless technology.

Bluetooth wireless technology is a short-range radio communication technology intended to
replace the cables connecting electronic devices. The technology uses a globally available
frequency range intended to ensure communication compatibility worldwide.

Caution:

Listening at full volume to music or voice through a headset may damage your hearing.

Control Button

MP3 next

LED LIGHT

Audio/charger
socket

BlueToothHeadSet Control Buttons and Display Screen:

BUTTON_MFB Multifunction Button
BUTTON_VOL+ Volume Increase
BUTTON_VOL- Volume Decrease
BUTTON_MP3_Preview MP3 Preview----preview MP3
BUTTON_MP3_Next MP3 Next----Pause MP3 playing/Next MP3

In this Bluetooth headset design, the three buttons above were integrate to a Control Button.
Middle is Multifunction Button(BUTTON_MFB), which can be use to control several headset
functions. You can turn the Control Button to adjust speaker volume(BUTTON_VOL+/-), more
detail as follow, you can turn deasil to increase volume , also you can turn anticlockwise to
decrease volume.

Bluetooth headset supports profiles and functions:

Hands-Free Profile(HFP), HeadSet Profile(HSP), Advanced Audio Distribution Profile(A2DP),

Bluetooth Intercom function,FM radio.

To use your headset, your phone or music device should
support the following Bluetooth profiles:

Profile Description

HFP(Hands-freeProfile

Providing a wireless means for both
remote control of the Mobile Phone by
the Hands-Free device and voice
connections between the Mobile Phone
and the Hands-Free device.

)

A2DP (Advanced Audio

Distribution Profile)

AVRCP

Stereo music streaming.

MP3 CONTROL

Bluetooth Interference Issues:

The quality of Bluetooth transmission may also be affected by the position of your music device.
Should you experience choppy or distorted audio, move the position of your music device or
phone to a different location until the signal improves.

Getting started:

Before you can use your headset, you should first:
Charge the headset battery.
Connect Audio Plug
Pair the headset with a device, for example, a mobile phone.

Charging:

The headset comes with a built-in rechargeable battery. We recommend that you charge the battery
before using the headset for the first time.
Connect the charger to the device.
The charging time is about 2 hours.During charging,Red LED is on. When the battery is fully
charged, Red LED is off. When you using the headset, if you hear a cadent tone, and Red LED is

flashed , battery needs recharging.

To charge, please use the handle on Charging Port Rubber Cover gently pull out the Cover,

Expose the Charging Port and Plug the Charger Plug int o the BlueTooth head set’s Charging Port.
At this time Red LED is on when the battery is charging. As Figure2 shown.

Connect Audio plug:

Connect Audio plug is the same as the charger.

Charging Port Rubber Cover

Charging Port

Charging Plug

Figure 2

To turn the headset on:

Press and hold the Multifunction Button(BUTTON_MFB) for approximately 2 seconds until
you hear a short low tone followed by a short high tone. Blue LED is flashed.
When turned on, the headset automatically establishes handsfree phone and streaming music
connections with the last connected Bluetooth devices (phone and/or music devices).

To turn the headset off:

Press and hold the Multifunction Button(BUTTON_MFB) for about 5 seconds until will hear a
short high tone followed by a short low tone.

To pairing the headset with a phone:

Before using the headset,you should pair the headset to your mobile phone.
The phone enter the searching BlueDevice mode and with the headset turned off, press and hold
the Multifunction Button(BUTTON_MFB) for about 5 seconds until Blue led and Red led is

flashed aterntively.

Operate the phone to discover and connect the headset. The headset passkey is 0000. If pairing
success.
Pairing, done only once. Each time you use your headphones, it will be automatically connected to
your phone.
Note:Before enter pairing mode,please make sure other BlueDevices are closed.