HeatWave SA1309, SA2409, SA2402 User Manual

OWNER’S MANUAL

ONEPERSON & TWOPERSON SAUNAS

WITH CERAMIC OR CARBON HEATERS

SA2400/SA2402/SA2406/SA2409/SA1309

TABLE OF CONTENTS

ASSEMBLY TIPS & WARNINGS

PARTS IDENTIFIER

ASSEMBLY INSTRUCTIONS

OPERATION INSTRUCTIONS

ENJOYING YOUR SAUNA

HEALTH & SAFETY WARNINGS

CLEANING & MAINTANENCE

TROUBLESHOOTING GUIDE

REPLACEMENT PARTS

5-10

14-15

16-25

WARRANTY INFORMATION

The information contained in this manual is subject to change without notice.

ASSEMBLY TIPS & WARNINGS

• Before you begin, read all assembly instructions and safety warnings carefully.

• This sauna requires at least 2 adults to complete assembly.

• Remove all of the contents from boxes and verify that you have all of the parts shown on the Parts Identier before you begin assembly. Note: Some parts may be pre-installed or pre-assembled.

• This manual is used for the assembly of several sauna models; therefore, some gures or drawings may not look exactly like your product.

• Cover the sauna oor during assembly to avoid staining the unnished wood surface.

• Retain this Owner’s Manual for future reference.

ELECTRICAL REQUIREMENTS

• We recommend consulting a licensed electrician and checking local ordinances before installing ANY sauna.

• This sauna requires a standard 15 amp receptacle.

• Refer to the serial plate on the back of the sauna for complete electrical specications.

• This sauna requires a dedicated circuit - No other appliances should share the same outlet with the sauna.

CHOOSING A LOCATION

• This sauna should only be placed INDOORS on a dry, level surface.

• There should be a minimum of 5 inches clearance between the sauna and any wall.

• Make sure the main power cord will reach the outlet and remains easy to access.

• The sauna should only be used in a dry location as moisture will damage the wood and electrical components.

• Keep the sauna away from any potential hazards including water sources, ammable objects and combustible materials.

PARTS IDENTIFIER (NOT TO SCALE)

* Refer to REPLACEMENT PARTS (PAGE 16-25) to determine the correct part number when ordering replacements.

ASSEMBLY INSTRUCTIONS

1. Begin assembly by determining an appropriate location for your sauna – see ASSEMBLY TIPS & WARNINGS for details. Attach the BACK PANEL to the FLOOR by lining up the BACK PANEL with the groove in the back of the FLOOR.

2. Attach the LEFT PANEL to the FLOOR. Buckle the LEFT PANEL to the BACK PANEL.

3. Attach the RIGHT PANEL to the FLOOR. Buckle the RIGHT PANEL to the BACK PANEL.

ASSEMBLY INSTRUCTIONS (CONT.)

4. Carbon Heater Models Only: Attach the FLOOR HEATER to the FLOOR with 1-1/2” SCREWS. Connect the heater plug.

5. Slide the BENCH HEATER PANEL into place between the LEFT and RIGHT PANELS. Connect the heater plug. Note: For Carbon Heater Models, make sure the FLOOR HEATER cable is placed

through the groove in the bottom of the BENCH HEATER PANEL.

6. Attach BENCH SEAT with 2” SCREWS.

ASSEMBLY INSTRUCTIONS (CONT.)

7. Ceramic Heater Models Only: Attach BACK PANEL HEATER COVER to BACK PANEL with 2” SCREWS and to BENCH SEAT with 3/4” SCREWS.

8. Attach the FRONT PANEL to the FLOOR. Buckle the FRONT PANEL to the LEFT and RIGHT PANELS.

9. Lift the ROOF above the sauna, feeding the control panel and heater cables through the corresponding holes. Feed the cables for the AM/FM CD PLAYER through the hole in the bottom of the ROOF. Note: For One-Person Models, the ROOF ts inside the four PANELS. Secure the ROOF to the sauna with 1-1/8” SCREWS. Connect the control panel and heater plugs.

ASSEMBLY INSTRUCTIONS (CONT.)

10. Feed the main power cable through hole in ROOF COVER. Secure the ROOF COVER with 3/4” SCREWS.

11. Attach the DOOR HANDLE to the GLASS DOOR.

12. Gently pull the cables for the AM/FM CD PLAYER through the opening in the front of the STEREO SHELF. Attach the STEREO SHELF with 3/4” SCREWS.

+ 18 hidden pages