HEATSTRIP TT-MTM2 Product Manual
PRODUCT MANUAL
TT-MTM2 Hard -W i red
Co n t r o ll e r w ith R e mot e
2
TT-MTM2 Hard-Wired Controller with Remote Rev C NOV15
TT-MTM2 Wall Controller
This controller is a custom designed and manufactured controller for HEATSTRIP® heaters. It has been designed for
ease of use and to provide low running costs of your heater. It provides both temperature control (allowing the user to
turn the heat output up or down depending on the ambient temperature and conditions) and a timer for automatic
heater shut-off operation.
The timer function has four settings: 1 hour, 2 hours, 4 hours or constantly on. This feature is ideal for applications
such as BBQ, alfresco areas, restaurant dining, assembly line production etc. when continuous heat is not required.
The timer also reduces the likelihood of heaters being inadvertently left turned on.
Depending on the ambient temperature there may be a requirement to control the heat output of the heater. The
controller has 3 settings, they are High, Medium and Low.
The controller allows a combination of the multiple timer (1/2/4 hour) and heat outputs (High/Medium/Low).
The controller comes with a remote control unit which provides
convenient control of the heater power output and timer functions.
Controlling multiple heaters
It is possible to use one wall controller to control multiple heaters.
The wall controller is rated at 16 Amps and 240 volts. For a larger
current draw, talk to your electrician who can use a relay to
connect more units.
Remote pairing
All units operate using the
same remote control
frequency, therefore, multiple
wall controllers can be
operated using a single remote
control.
The remote will function at
distances of over 8m when
used in a straight line. This
distance reduces when used at
an angle.
MODEL MAXIMUM
VOLTAGE (Volts)
MAXIMUM
CURRENT (Amps)
PACKAGED
DIMENSIONS (mm)
UNIT
WEIGHT (kg)
TT-MTM2 240 16 150 x 95 x 55 0.3
3
Operation
Press “ON/OFF” button to turn power on and off.
Once turned on, the controller will default to High power setting and will be permanently on (no timer function).
Press “POWER” button to select the desired power setting by cycling through: HIGH – MEDIUM – LOW.
When power setting is at high the controller will provide continuous power. When power setting is at “MEDIUM”
or “LOW” the output alternates between being on and off so that it delivers a lower output to the heater.
Press “TIMER” button to set the timer to 1, 2, 4 hours or permanently on. When permanently on, none of the
TIMER LED’s will be illuminated. Once the timer is selected, the timer will be started immediately. When the
timer has ended, power will turn off and all LED’s will be also turn off.
All features can be accessed using either the wall controller buttons or the remote control unit.
Thermal Cut-Out Protection
This controller is protected by a thermal cut-out switch. This switch is activated when the temperature of the con-
troller is too high. The controller will cut all power until it has sufficiently cooled. Once it cools the unit will contin-
ue working as usual.
Warm Up Mode
The controller is programmed to operate continuously (High setting) for the first 15 minutes of operation regardless of the selected power setting. This is to allow time for the heater to warm up. After this time it will operate as
selected.
Safety
The TT-MTM2 controller is to be mounted indoors. It needs to be away from wet conditions.
Ensure the connections are properly connected.
The controller needs to be installed according to your local wiring guidelines and regulations.
Do not allow any cables, furnishings, flammable materials or other items to obstruct the vents of the controller.
Never block the air vents of the controller.
Do not put anything in the vents of the controller.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or intellectual capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to en-
sure they do not play with the appliance.
Maintenance
The TT-MTM2 Controller is made from durable materials, however regular care and maintenance of your controller will help prolong the life of the product.
It is recommended that you dust the controller to keep the surface clean. Cleaning at least every three months
will reduce the amount of dust build up and keep it looking at its best.
Do not use any abrasive materials or products to clean the controller, this includes solvents, citrus based clean-
ers or other harsh cleaning products. Do not use water or a damp cloth to clean the controller.
The remote uses a CR2025 3V lithium battery. If the red light on the remote stops working then change the bat-
tery.
Loading...