HEATSTRIP MHS-FBM, MHS-FBHS, MHS-FBWS, MHS-ESM User Manual

User manual for HEATSTRIP™ radio receiver

Remote control systems

for

This installation and user
manual encompasses
information about the
following products:

MHS-FBM
MHS-FBHS
MHS-FBWS
MHS-ESM

Exclusively engineered and made in Germany

D

Table of contents

1.0 Use page 2

2.0 Safety Information page 2

3.0 Functionality description page 4

4.0 Assembly page 5

5.0 Programming page 7

6.0 Operation page 9

7.0 Connecting element MHS-ESM page 10

8.0 Technical Information back page

Delivery:
Radio receiver module 1 piece
Power connector (already installed on the machine) 2 pieces
Assembly and user manual 1 piece

and optionally
Hand held remote control 1 piece
or
Wall-mounted remote control 1 piece

1

The connecting element serves as a stylish cable connection for your Heatstrip, hiding
the power cable at the backside of the device - instead of it being visible at the front side.
Install the connecting element after point 4.0 in this user manual.

It is not possible to further program or set this element.

7.0 Connecting element

1.0 Use – 2.0 Safety information

2

Thank you for choosing HEATSTRIP™, the black light infrared electric heater. This
user manual will guide you through the connection and programming of the radio
receiver MHS-FBM. These instructions are an addition and valid only in combina­tion with the general HEATSTRIP™ manual, chapter 4.7.

Our remote controls are powered by the EnOcean technology, which enables them
to run battery free. When pressing the button of the remote control, the system
harnesses the physical pressure of your thumb onto the remote control and
converts it into an electro-magnetic signal that is picked up by our MHS-FBM
receiver.

Electronic smog and radio signals

Many people are worried about the possible consequences for their health of the
electronic smog created by the countless electrical fields due to the many wireless
devices we are surrounded by. Manufacturers hence worry about possible claims
for damages based on such health related harm. Nevertheless, the need for
wireless devices keeps increasing quickly. Therefore, we had the standard
intensity of the electro-magnetic fields created by our radio receivers measured by
ECOLOG under in situ usage conditions (ECOLOG is the German Institute for
Socio-Ecological Research and Education).

What are the results?

1. The Enocean Radio system emits one hundred times less intensive
high-frequency fields than conventional light switches (the latter’s high-frequency
fields are produced through the characteristic sparkling switching process).

2. The intensity of the quick high-frequency emissions of the EnOcean radio switch
are up to 10,000 times fewer than the permanent high-frequency emissions of the
mobile phone network stations in residential homes.

3. Thanks to the lack of cables and switches, our radio system works without
interefering with low-frequency electro-magnetic emissions.

4. This radio system is used in schools, hospitals, and even in houses built
according to Feng Shui principles.

Remote control programming

- Press briefly the lateral button on the MHS-FBM receiver (less than 1 sec).
Three green LEDs + one blue LED flash two times per second.

- On the remote control, press and release the button you wish to control the device with.
Then the LEDs blink for 2 seconds while the radio button is being synchronized with
the MHS-FBM receiver
To terminate the programming mode, wait for 30 seconds or press the programming button.
The chosen switch is saved.

Remote control resetting

- Press briefly and release the lateral programming button on the MHS-FBM receiver
(less than 1 sec). Three green LEDs + one blue LED flash two times per second.

- On the remote control, press and release button to reset.
The LEDs flash 10 times, then the button is reset.

- To terminate the reset mode, wait for 30 seconds or press the programming button.

Setting of maximum heating duration

- Press and hold the lateral button for more than 2 seconds.

- After 2 seconds the blue LED will briefly flash three times:
the blue LED flashes every second,
the green LEDs show the set time.

- Each short press & release of the lateral button on the receiver will increment
the heating duration according to the built-in Time-Code (see below).

- The heating duration can also be changed by pressing the button that has been
previously programmed.

- After 30 seconds following the last press & release, the programming will end and
the chosen Time-Code set is saved.

Time-Code

Can be set from minimum 30 minutes to maximum 12 hours.
7 settings to choose from: 0.5, 1, 2, 3, 4, 8, 12 hours.

2.0 Safety information

When planning where to locate your device, please check accessibility
to the different components as you may have to access them in the future.
Electronic components may also fail and have to be replaced.
Only to be installed by a professional.

Please check the cable cross -section between the heater and
the power supply is sufficient in terms of size and power.

The surrounding temperature should not exceed 40 degrees Celsius.

Exclusively for 230V / 50 Hz AC .

Keep the devise away from physical chocs and do not use force.

Protect from wetness and moisture.

Do not install in the proximity of open fire.

Do not install where surrounding temperatures
are constantly below 0 degrees Celsius.

3