Heat Seal 500A Parts List
OPERATING & SERVICE PARTS MANUAL
TABLE TOP OVERWRAPPERS
AXLE MOUNT MODELS:
SINGLE ROLL WITH MOUNTING AXLES
MODEL 625A MINI
COMPACT SINGLE ROLL WITH MOUNTING AXLES
MODEL 625A
Model 625A
Model 600A
MODEL 825A
DUAL ROLL WITH MOUNTING AXLES
MODEL 875A
TRIPLE ROLL WITH MOUNTING AXLES
FILM ROLLER MODELS:
MODEL 600A
SINGLE ROLL WITH ROLLERS
MODEL 500A
COMPACT SINGLE ROLL WITH ROLLERS
MODEL 500A MINI
COMPACT SINGLE ROLL WITH ROLLERS
MODEL 800A
DUAL ROLL WITH ROLLERS
MODEL 850A
TRIPLE ROLL WITH ROLLERS
Model 825A
READ ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING EQUIPMENT
Revised 2013
TABLE OF CONTENTS
Film Threading ............................................................................................................... 3
Installing the Film Axle .................................................................................................. 4
625A Schematic & Parts List ........................................................................................ 5
625A Mini Schematic & Parts List ................................................................................ 6
825/875A Schematic & Parts List ................................................................................. 7
600A Schematic & Parts List ........................................................................................ 8
800/850A Schematic & Parts List ................................................................................. 9
Electrical Service Information .................................................................................... 10
Electrical Schematics .................................................................................................. 11
Electrical Box & Hot Plate Schematic & Parts List ................................................... 12
2
Revised 2013
FILM THREADING
FOR AXLE TYPE WRAPPERS (625, 825, 875):
See instructions on next pages to load the film onto the axle.
Thread the film as shown, one at a time or as needed.
FOR ROLLER TYPE WRAPPERS (600, 800, 850):
Rest film Roll on top of two rollers, centering film between the film guides. Tighten the thumbscrew against the film brake to
ensure proper film tension. Thread the film as shown, threading one at a time or as needed.
3
Revised 2013
INSTALLING & ADJUSTING THE FILM AXLE
INSTALLING COMPLETE AXLE ASSEMBLY (625-A)
Position the complete axle assembly on the rear of the
wrapper with the removable end cap (1) on the left side and
the bearing blocks (2) on the outside of the sides of the
machine base (3) as shown in the drawing.
Fasten the bearing blocks to the sides of the machine base
with the four bolts (4), lock washers (5) and hex nuts (6)
provided in the bearing block set.
INSTALLING COMPLETE AXLE ASSEMBLY (825-A/875-A)
Position the complete axle assemblies between the side
plates of the wrapper with the removable end cap on the
left side and the bearing blocks and mounting brackets on
the inside of the plates.
Fasten bearing blocks, mounting bracket and axle to the
side plates with the fasteners provided in the bearing block
set
REMOVING THE AXLE
Remove the protective caps from the ends of both bolts
located in the slotted holes of the upper bearing blocks (7).
Remove the wing nuts on both bolts with the protective
caps removed and loosen the wing nuts on both bolts located in the other holes of the upper bearing blocks.
Swing the upper bearing blocks toward the outside of the
machine base until the ends of the axle (8) are exposed.
INSTALLING THE AXLE
Place the ends of axle into the grooves on lower bearing
blocks with the removable end cap positioned on the left
side as shown in the illustration.
Swing the upper bearing blocks toward the inside of the
machine base until they align with the lower bearing blocks.
Thread the wing nuts onto both of the bolts located in the
slotted holes of the upper bearing blocks and tighten all of
the wing nuts on all four of the bolts in the bearing block
assemblies.
Replace the protective caps on the ends of both bolts located in the slotted holes of the upper bearing blocks.
CHANGING THE AXLE END CAP WIDTH
Pull pin (10) out of the outer flange of hub (11) until the end
of pin clears the inner flange of hub. Do not completely
remove the pin from the hub.
Slide the hub to the new position and align the hole on the
inner flange on hub with the nearest hole in the axle.
Push the pin completely through the inner flange of hub and
the axle until the top of the pin is flush with the outer flange
of hub.
Lift the axle out of the lower bearing blocks (9).
Revised 2013
4
MODEL 625A REPLACEMENT PARTS
ITEM
1
2
3
4
5
6
7
8
9
PART # DESCRIPTION
6110-023 Film Core Adapter Set
6305-018 Bearing Block Set
3005-004 Film Core Axle, 21 15/16” L
6101-020 Hot Plate Assy, 6 by 15
6102-043 Hot Plate Assy, 8 by 15
6102-052 Wrapping Bridge
5901-011 Non-stick Cover, 6 by 15
5901-001 Non-stick Cover, 8 by 15
6301-019 Film Retainer Rod
1824-011 Cut-Off Rod, 23” L
6301-018 Vinyl Film Retainer
5
ITEM
10
11
12
13
14
15
16
17
18
19
PART # DESCRIPTION
6305-048 Bearing Block Support Bracket
2135-001 Large Rubber Foot
1903-188 Hex Head Cap Screw
3005-010 Cut-Off Rod Collar
1927-008 Vinyl Clamp
1833-002 Fiber Insulator Washer
1958-001 Metal Shaft Retainer
1907-005 Lock Washer
2150-232 Hi-Lo Decal
1909-019 No. 10 Flat Washer
Revised 2013
Loading...