Heath Zenith SL-6190, SL-6290 User Manual

Wireless Push Button Accessory

SL-6190 Series and SL-6290 Series (Style may vary from illustration)

The Heath®/Zenith Wireless Push Button Accessory works with existing Heath®/Zenith jumper or dip switch systems.

• Battery powered push button - No wires to run.

• 128 selectable codes allow more than one chime system in the same house.

1. Install alkaline type A23 12 volt push

button battery. Remove back of case

by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 5).

2. Set the push button jumpers to match the chime receiver

code. See “Code and Tune Setting” section.

3. Test range. Temporarily position push button where you want

it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting.

4. Mount push button.

Use either screws or double sided tape to mount push button.

To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver.

Attach back of case to door jamb or wall. Snap front of push button on.

When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean.

-2-

595-5507-11

Code and Tune Settings

Code Settings

Note: Most installations will not require you to change any jumpers on your chime and push button.

WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power.

The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code.

1. Unplug wireless chime (if applicable).

2. Open the cases and locate the jumpers on both the push button

and chime (See illustration on page 5).

3. The push button and chime both have eight different jumper

locations. The jumper positions 1 through 7 are used for setting the code.

4. To change the code, add and/or remove jumpers as needed. It

is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function.

595-5507-11

-3-

Tune Settings

Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below.

• Ding (one note tune) Push button: Add a jumper to location 8.

• Ding-Dong (two note tune) Push button: Remove jumper from location 8. Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected Heath®/

Zenith chimes) Push button: Remove jumper from location 8. Chime: Add a jumper to location 8.

Note: All models have both front and back door tune capabilities. You may purchase any Heath®/Zenith wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected Heath®/Zenith chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting.

-4-

595-5507-11

Remove

screw to open

access door

Back of

Chime

12 345 678

Tune Setting (Not

used on all models)

Push Button Battery Replacement

Install an alkaline type A23 12 Volt battery. See diagram inside push but-

ton for correct battery orientation.

12 3 45 67 8

* Code Settings 1-7 Must Match

Both Push Button

and Chime

Inside Push

Button

Tune

Setting

Note: Some models might require the use of tweezers to remove and replace the jumpers.

595-5507-11

-5-

Chime does not sound:

Troubleshooting

• Make sure push button and chime codes are the same (See pages 3,

4, and 5).

• Check orientation of push button battery (See page 5).

• Check charge of push button and chime batteries (if applicable), replace

if necessary.

Batteries seem OK, but the chime does not work when installed:

• Do not mount chime or push button on metal or near metal studs. This

reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood

shims to move chime or push button off metal surface.

• Concrete ﬂoors may reduce range. Move chime away from ﬂoor.

• Try locating chime closer to push button. The range of the wireless chime can vary with location, temperature and

battery condition.

-6-

595-5507-11

Technical Service

Please call 1-800-858-8501 (English speaking only) for as-

sistance before returning product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to: HeathCo LLC P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The user is cautioned that changes or modiﬁcations not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.

HeathCo LLC reserves the right to discontinue and to change speciﬁcations at any time without notice without incurring any obligation to incorporate new features in previously sold products.

595-5507-11

-7-

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may also

FIVE YEAR LIMITED WARRANTY

have other rights which vary from state to state or province to province.

For a period of ﬁve years from the date of purchase, any malfunction caused by

factory defective parts or workmanship will be corrected at no charge to you. To

obtain a refund or a replacement, return the product to the place of purchase.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, and expendable items are not covered by this warranty.

Unauthorized service or modiﬁcation of the product or of any furnished com-

ponent will void this warranty in its entirety. This warranty does not include

reimbursement for inconvenience, installation, setup time, loss of use, or

unauthorized service.

This warranty covers only HeathCo LLC assembled products and is not

extended to other equipment and components that a customer uses in con-

junction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION

OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT

FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF

ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS-

TOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO

LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS

OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces

do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you. Please keep your

dated sales receipt, it is required for all warranty requests.

-8-

595-5507-11

+ 16 hidden pages