Heath Zenith HD-9274, HD-9272 User Manual
Model HD-9272: 150 Watt High Pressure Sodium Security Light
Model HD-9274: 100 Watt Metal Halide Security Light
Installation Instructions
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.
NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through
conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of
the system.
Lamp in Fixture Contains Mercury. Dispose According
to Local, State, or Federal Laws.
WARNING: Turn power off at the fuse or circuit
breaker.
1. Select a location on a flat wall with structurally sound wood
and from 10 to 25 feet from the ground. The wood should
be at least one inch thick to safely secure the fixture.
2. Attach the cover plate using two large machine screws.
3. Using the mounting bracket as a template. Hold it at the
desired mounting location (making sure the bottom is
level), and mark four mounting holes. We suggest drilling
3/16" pilot holes for the lag screws.
4. Put the two top lag screws through their holes in the
mounting bracket and hold them in place while you push
the gasket onto these lag screws. Start these two screws
into the two top pilot holes.
5. Start the other two lag screws, and then tighten all four
screws.
6. Hang the fixture on the mounting bracket using the slot
in the cover plate.
7. Twist the fixture wires to the supply wires. (black to black,
white to white, and the bare fixture wire to the supply
ground wire).
8. Make sure the wires do not get pinched, and swing the
fixture up so the base fits tightly against the gasket. Push
the pin through the hole at the top near the gasket, and
into the mating loop in the mounting bracket. You may
need to tap the pin to seat it all the way down.
9. Secure the fixture with the small machine screw going
through the cover plate and into the mounting bracket.
10. Install lamp. Lamp rating must match the rating of the
fixture.
Model 9272: 150 Watt high pressure sodium type S55
lamp.
Model 9274: 100 Watt metal halide type M90/O open
rated lamp.
11. Hold the lens and wire cage up to the fixture and align the
clips on the wire cage with the protrusions in the housing.
Hook the clips over these protrusions and snap the clips
closed to hold the lens and wire cage in place.
12. Loosen the screw in the center of the photocontrol socket
two turns. Twist the socket so that the arrow points north.
Note: There is a stop to prevent the socket from turning
all the way around. If you have trouble turning the socket,
© 2008 HeathCo LLC 598-1246-04
try turning it the other direction. Retighten the screw in
the center of the socket.
13. Align the photocontrol (it will only plug-in one way). Plug
it in and twist clockwise until it stops.
14.
Caulk fixture mounting surface with silicone weather sealant
To test operation during daylight, cover the photocontrol with
a small box. Turn on the power. Not all photocontrols are alike.
Some may have a time delay of a few minutes, others will turn
on as soon as power is applied. The light will take up to ten
minutes to reach full brightness. Uncover the photocontrol and
your unit will operate automatically—on at dusk, off at dawn.
Housing
Lamp
Cover
Plate
Photocontrol
Pin
Lag Screw
Lens
(4)
Mounting
Bracket
Gasket
TECHNICAL SERVICE
Please call 1-800-858-8501 (English speaking only) for assistance before
returning product to store.
If you experience a problem, follow this guide. You may also want to visit our Web site at: www. hzsupport.com. If the prob-
lem persists, call* for assistance at 1-800-858-8501 (English speaking only), 7:30 AM to 4:30 PM CST (M-F). You may also
write* to:
HeathCo LLC
P.O. Box 90045, Bowling Green, KY 42102-9045
ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and
Place of Purchase.
No Service Parts Available for this Product
JourneyMan® Lifetime Warranty
This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state
to state or province to province.
For as long as you (the original purchaser) own this JourneyMan® product, any malfunction caused by factory defective
parts or workmanship will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries,
and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of
any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only JourneyMan® products and is not extended to other equipment and components that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR
ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO
LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty
requests.
2
598-1246-04
Modelo HD-9272: Lámpara de seguridad de sodio de alta presión
de 150 vatios
Modelo HD-9274: Lámpara de seguridad halógena metálica de 100
vatios
Instrucciones Para La Instalación
ANTES DE EMPEZAR LA INSTALACIÓN LEA CUIDADOSAMENTE TODAS LAS INSTRUCCIONES
NOTA: Todo el cableado debe realizarse de acuerdo con el Código Nacional Eléctrico (Código Eléctrico Canadiense en
Canadá) usando tubería u otro medio aceptable. Contáctese con un electricista calificado si tiene alguna pregunta
respecto a la adaptabilidad del sistema
La lámpara en el dispositivo contiene mercurio. Deseche de acuerdo con las leyes locales, estatales o
federales.
ADVERTENCIA: Apague la energía en el fusible o
cortacircuitos.
1. Seleccione la ubicación en una pared plana de madera
estructuralmente firme y entre 10-25 pies del suelo. La
madera debería ser al menos de una pulgada de espesor
para asegurar firmemente al artefacto.
2. Coloque la placa cubertora usando los dos tornillos para
metal grandes.
3. Use la consola de montaje como plantilla. Sosténgala en
la ubicación de montaje deseada (Asegúrese que la base
inferior esté a nivel), y marque la ubicación de los cuatro
orificios de montaje. Le sugerimos taladrar orificios guías
de 3/16” para los tirafondos.
4. Pase los dos tirafondos superiores por los orificios correspondientes de la consola de montaje y sosténgalos
en su lugar mientras empuja el empaque permitiendo que
estos tirafondos lo traspasen. Pase estos dos tornillos por
los dos orificios guías superiores.
5. Pase los otros dos tirafondos, ajuste luego los cuatro
tirafondos.
6. Cuelgue el artefacto en la consola de montaje usando la
ranura de la placa cubertora.
7. Entorche los cables del artefacto con los cables de
alimentación. (negro con negro, blanco con blanco, y
el cable desnudo del artefacto al cable de tierra de
alimentación).
8. Asegúrese que los cables no se aprieten y balance el
artefacto hacia arriba de modo que la base encaje firmemente contra el empaque. Empuje la clavija por el orificio
superior cerca del empaque, y por el ojal de contacto
de la consola de montaje. Puede ser necesario golpear
ligeramente la clavija para asentarla en el fondo.
9. Asegure el artefacto usando el pequeño tornillo para metal
que pasa por la placa cubertora y la consola de montaje.
10. Instale la bombilla. La potencia nominal de la lámpara
debe emparejar con la potencia nominal del artefacto.
Modelo 9272: bombilla de sodio a alta presión de 150
vatios tipo S55.
Modelo 9274: bombilla halógena metálica de 100 vatios
tipo M90/O.
11. Sostenga la placa traslúcida y la jaula de alambre hacia arriba
contra el artefacto y alinee las presillas de la jaula de alambre
con las salientes de la carcasa. Enganche las presillas en
estos salientes y cierre a presión las presillas para que la
placa traslúcida y la jaula de alambre queden en su lugar.
12. Afloje en dos vueltas el tornillo que está en el centro del
zócalo del fotocontrol. Gire el zócalo de modo que la
flecha apunte al norte. Nota: Hay un tope para impedir
que el zócalo gire toda la vuelta. Si Ud. tiene problema
en girar el zócalo, inténtelo en la otra dirección. Vuelva a
ajustar el tornillo del centro del zócalo.
13. Alinee el fotocontrol (sólo se enchufará de una forma).
Enchúfelo y gírelo en sentido horario hasta el tope.
14. Calafatee el aparato y la superficie de montaje con un
sellador de silicona contra la intemperie.
Para probar el funcionamiento durante las horas diurnas,
cubra al fotocontrol con una caja pequeña. Encienda la energía. No todos los fotocontroles son iguales. Algunos pueden
tener un retardo de tiempo de unos pocos minutos, otros se
encenderán tan pronto se aplica la energía. A la luz le tomará
hasta diez minutos en alcanzar su brillo total. Retire la caja del
fotocontrol y su unidad trabajará encendiéndose al crepúsculo
y apagándose al amanecer.
Carcasa
Lámpara
(bulbo)
Placa
cubertora
Fotocontrol
Clavija
Tirafondo(4)
Consola
de Montaje
Empaque
Placa Traslúcida
598-1246-04
© 2008 HeathCo LLC 598-1246-04 S
3
Loading...