Heath Zenith 3035490, 3035466, 3196417, AC-6180, AC-6186 User Manual

-

+

-

+

-

+

Battery

Battery

Battery

Decorative

Wireless Chime

3196417 (AC-6182), & 3035490 (AC-6186)

This package includes (Style of push button and chime may vary from illustrations):

• Wireless chime

• Wireless push button w/battery

• Hardware pack
You'll need to buy 3 "D" alkaline batteries for the chime. In typical use,

alkaline batteries will last up to three years.

Figure 1

Chime

Volume

Cover

Mounting

Tabs

Figure 2

Jumpers

Models 3035466 (AC-6180),

1. Install alkaline type A23 12
volt push button battery. Re-

move back of case by pushing
in tab on bottom with a small
screwdriver (see Figure 1).
Make sure battery is oriented
properly (See page 4).

2. Install 3 alkaline “D” batteries.
Make sure batteries are oriented
properly (see Figure 2).

3. Test range.

tion chime and push button
where you want them mounted.
Press push button to verify
chime and push button work
properly. If chime does not
sound, see Troubleshooting.

Temporarily posi-

© 2007 598-1074-02

12

345

6

7

8

4. Mount push button. Use either screws or

double sided tape to mount push button.

To mount with screws, remove back of case by
pushing in tab on bottom with a small screw­driver.

Attach back of case to door jamb or wall. Snap front
of push button on.

Figure 3

When attaching push button using double sided
tape, make sure the surface of the door jamb or
wall is clean.

5. Mount chime. There are two different ways to mount the chime depending

upon the model of chime purchased. Determine which model you purchased
below. Mount the chime according to the instructions for your chime.

Chime with sawtooth hanger attached to back:

1. Drill 1/4" diameter pilot hole for wall anchor (provided) and insert anchor.

2. Screw #8 screw (provided) into anchor. Leave 1/16" gap between screw
head and wall.

3. Place hanger over screw to mount chime.

Sawtooth Hanger

Chime Volume

Jumpers

Figure 4

-2-

598-1074-02

Chime with separate cover and base:

The chime base can be mounted in two different ways. The base can be mounted
using the keyholes or the three mounting holes. The base may be mounted hori­zontally or vertically depending upon the specific model purchased.

1. Remove batteries from chime.

2. Use template on back cover for screw placement. Drill 7/32" diameter pilot
holes for wall anchors (provided) and insert anchors.

3a. If using the three hole method to mount chime, insert three #6 screws

(provided) through holes in back of chime.

3b. If using keyhole method to mount chime, screw two #6 screws into wall

anchors. Leave 1/16" gap between screw head and wall.

4. Using arrow on template as a guide, mount chime with arrow pointing up.

5. Replace batteries (see Figure 2). Place chime cover over base.

Code and Tune Settings

Code Settings

Note: Most installations will not require you to change any jumpers on
your chime and push button.

The push button and chime communicate by using a code that can be changed
by removing and/or adding jumpers on both the push button and chime. The
code is factory set; however, there are 128 selectable codes that allow you to
expand your system and prevent outside interference. Other wireless products
may cause interference and the system may not function properly. Follow the
instructions below for setting a new code.

1. Open the cases and locate the jumpers on both the push button and chime
(See illustration on page 4).

2. The push button and chime both have eight different jumper locations. The
jumper positions 1 through 7 are used for setting the code.

3. To change the code, add and/or remove jumpers as needed. It is recom
mended to only change one jumper at a time and then check to see if
system is functioning properly.

Note: Jumpers in positions 1 through 7 must be exactly the same for both
the push button and chime for this system to function.

598-1074-02

-3-

-

Batter y

C

h

i

m

e

V

o

l

u

m

e

Tune Settings

Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong
(two note), or Westminster (eight note) (Available on selected chimes). The
factory setting is for the Ding-Dong tune (or Westminster, when available). This
tune can be changed by following the instructions below.

• Ding (one note tune)

Push Button: Add a jumper to location 8.

• Ding-Dong (two note tune)

Push Button: Remove jumper from location 8.
Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected chimes)

Push Button: Remove jumper from location 8.
Chime: Add a jumper to location 8.

Note: All models have both front and back door tune capabilities. You may pur­chase any ACE® wireless push button for a second entrance. We recommend
the back door use the Ding tune and the front door use the Ding-Dong tune
(or Westminster tune, available on selected chimes). Models that include two
push buttons will come factory set for front and back doors. Decals on the rear
of the push button will indicate its setting.

Push Button Battery Replacement

Install an alkaline type A23 12 Volt battery.

See diagram inside push button for correct

Inside Chime

battery orientation.

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

* Code Settings 1-7

Must Match Both
Push Button and

Tune Setting
(Not used on

all models)

Inside Push

Button

Note: Some models might require the use of
tweezers to remove and replace the jumpers.

-4-

Chime

Tune Setting

598-1074-02

Troubleshooting

Chime does not sound:

• Make sure push button and chime codes are the same (See pages 3 and 4).

• Check orientation of push button battery (See page 4).

• Check charge of push button and chime batteries, replace if necessary.

Batteries seem OK, but the chime does not work when installed:

• Do not mount chime or push button on metal or near metal studs. This

reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to
move chime or push button off metal surface.

• Concrete floors may reduce range. Move chime away from floor.

• Try locating chime closer to push button.

The range of the wireless chime can vary with location, temperature and bat­tery condition.

Please call 1-800-858-8501 (English speaking only) for assistance

If you experience a problem, follow this guide. You may also want to visit our
Web site at: www.hzsupport.com. If the problem persists, call* for assistance
at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
HeathCo LLC
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service
* If contacting Technical Service, please have the following information available:
Model Number, Date of Purchase, and Place of Purchase.

before returning product to store.

No Service Parts Available for this Product

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

The user is cautioned that changes or modifications not expressly approved by
the party responsible for regulatory compliance could void the user’s authority
to operate the equipment.

Technical Service

598-1074-02

-5-

This is a “Limited Warranty” which gives you specific legal rights. You

LIMITED WARRANTY

may also have other rights which vary from state to state or province
to province.

For a specified period depending upon model (see chart below) from the
date of purchase, any malfunction caused by factory defective parts or
workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items
are not covered by this warranty. Unauthorized service or modification of
the product or of any furnished component will void this warranty in its
entirety. This warranty does not include reimbursement for inconvenience,
installation, setup time, loss of use, unauthorized service, or return ship­ping charges.

This warranty covers only ACE® assembled products and is not extended
to other equipment and components that a customer uses in conjunction
with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN­TIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRE­SENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE
PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND
SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE
CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF
ACE® FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN­TIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF
BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some
states or provinces do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not
apply to you. Please keep your dated sales receipt, it is required for all
warranty requests.

Model Warranty Period

6270 Series 1 Year
6180 Series, 6283, 6284 5 Years

ACE® reserves the right to discontinue and to change specifications at any time
without notice without incurring any obligation to incorporate new features in
previously sold products.

-6-

598-1074-02

-

+

-

+

-

+

Battery

Battery

Battery

Campanilla

Decorativa Inalámbrica

3196417 (AC-6182), & 3035490 (AC-6186)

Este paquete tiene (El estilo del pulsador y de la campana puede variar de
la ilustración):

• Campana Inalámbrica

• Pulsador inalámbrico con batería

• Paquete de ferretería

Usted deberá comprar 3 pilas alcalinas “D” para el timbre. Con un uso
normal, las pilas alcalinas durarán hasta tres años.

Figura 1

Control del Volumen

de la Campana

Aletas de

montaje

de la

cubierta

Figura 2

Puentes

Modelos 3035466 (AC-6180),

1. Instalar pila alcalina de botón
tipo A23 de 12 voltios. Extraer

la parte posterior de la caja
presionando la aleta en el botón
con un destornillador pequeño
(vea la Figura 1). Asegurar­se que la pila esté orientada
correctamente (ver la página

10).

2. Coloque las 3 pilas alkalinas
“D”. Asegúrese de que estén

correcta-mente colocadas (vea
la Figura 2).

3. Pruebe el alcance. Pong a
provisionalmente la campana
y el pulsador en la posición
donde los quiera instalar. Pre­sione el pulsador para verificar
que la campanay el pulsador
funci onen apropiadame nte.
Si la campana no suena, vea

Análisis de Averías.

598-1074-02© 2007 598-1074-02 S

-7-

12

345

6

7

8

4. Instale el pulsador y el timbre.

Use ya
sean tornillos o cinta adhesiva por ambas
caras para instalar el pulsador.

Para montar con tornillos, quite la parte de atrás de la
caja empujando hacia adentro la lengüeta de abajo
con un destornillador pequeño y girando la cuchilla.

Coloque la parte de atrás de la caja contra la

Figura 3

jamba o la pared. Encaje a presión la parte
frontal del pulsador.

Cuando fije el pulsador usando cinta adhesiva
por ambas caras, asegúrese que la superficie de la pared o la del batiente de la
puerta estén limpias.

5. Monte la campana. Hay dos maneras diferentes de montar la campana

dependiendo del modelo de campana que compró. Determine abajo cuál
modelo compró. Monte la campana de acuerdo a las instrucciones que
corresponden a su campana.

Campana con colgador con diente de sierra fijado atrás:

1. Taladre un orificio guía de 6.4 mm (1/4 pulgadas) de diámetro para el ancla

de pared (provista) e inserte el ancla.

2. Atornille en el ancla el tornillo Nº 8 (provisto). Deje una separación de 1.5

mm (1/16 de pulgada) entre la cabeza del tornillo y la pared.

3. Coloque el colgador sobre el tornillo para montar la campana.

Colgador dentado

Control del Volumen

de la Campana

Puentes

Figura 4

-8-

598-1074-02