Heat & Glo LifeStyle DAKOTA 42H, DAKOTA 42 User Manual
Models:
Dakota 42
Dakota 42H
Owner’s Manual
Installation and Operation
CAUTION
DO NOT DISCARD THIS MANUAL
•
• Important operating
and maintenance
instructions included.
Read, understand
and follow these
instructions for safe
installation and
operation.
WARNING
If the information in these instructions is not followed exactly, a
fi re may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas:
- Do not try to light any appliance.
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or
the gas supplier.
DO NOT
DISCARD
•
Leave this
manual with party
responsible for use
and operation.
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot during
operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high
temperatures.
• Keep clothing, furniture, draperies and other
combustibles away.
This applian ce has b e e n supplied with an inte gral barrier to
prevent direct contact with the fi xed glass panel. Do NOT
operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.
Installation and service of this appliance should
be performed by qualifi ed personnel. Hearth &
Home Technologies suggests NFI certifi ed or
factory-trained professionals, or
technicians supervised by an NFI
certifi ed professional.
Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05 1
Note: This appliance must be installed outside.
Note: An arrow () found in the text signifi es change in
content.
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations
Congratulations on selecting a Heat-N-Glo LifeStyle Collection
gas appliance—an elegant and clean alternative to wood
burning appliances. The Heat-N-Glo LifeStyle Collection gas
appliance you have selected is designed to provide the utmost
in safety, reliability, and effi ciency.
As the owner of a new appliance, you’ll want to read and
carefully follow all of the instructions contained in this owner’s
manual. Pay special attention to all cautions and warnings.
This owner’s manual should be retained for future reference.
We suggest you keep it with your other important documents
and product manuals.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
Your new Heat-N-Glo LifeStyle Collection gas appliance will
give you years of durable use and trouble-free enjoyment.
Welcome to the Heat-N-Glo LifeStyle Collection family of
appliance products!
We recommend that you record the following pertinent
Homeowner Reference Information
information about your appliance:
Model Name: Date purchased/installed:
Serial Number: Location on appliance:
Dealership purchased from: Dealer phone:
Notes:
Listing Label Information/Location
The model information regarding your specifi c appliance can be found on the rating plate usually located in the control area
of the appliance.
Type of Gas
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1 in
the USA installation codes.
Heat-N-Glow Lifestyle Products
Hearth & Home Technologies Inc.
20802 Kensington Blvd., Lakeville, MN 55044
Vented gas fireplace - for outdoor installation
only. Not for use with solid fuel. (Foyer au
gaz à évacuation - pour installation à
l'extérieur seulement. Ne doit pas entre
utilise avec un combustible solide.)
This product is covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevels suivants): (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322; 4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254; 5,191,877;
5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia) 543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).
ANSI Z21.50-2002 - CSA 2.22-M02
Minimum Permissible Gas Supply for Purposes
of Input Adjustment. Natural Gas Propane Gas
Approved Minimum (De Gaz) Acceptable . . .7.0 in. w.c. (Po. Col. d'eau) . . . .
11.0 in. w.c. (Po. Col. d'eau)
Maximum Pressure (Pression) . . . . . . . . . . . . 10.0 in. w.c. (Po. Col. d'eau) . . . 14.0 in. w.c. (Po. Col. d'eau)
Maximum Input BTUH: . . . . . . . . . . . . . . . . . . . 61,000 . . . . . . . . . . . . . . . . . . . . . . 52,000
Orifice Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . #25DMS . . . . . . . . . . . . . . . . . . . . .#44DMS
Gas and Electric Information
Serial Number
22UM
Serial (Serie):
OD
Mfg. Date:
Model
(Modele):
VENTED GAS
FIREPLACE
Model Number
MADE
IN USA
DAKOTA42
DAKOTA42L
2 Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05
Table of Contents
1 Listing and Code Approvals
A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . 4
B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . 4
2 Getting Started
A. Design and Installation Considerations . . . . . . . . . . . . 5
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . .5
C. Inspect Appliance and Components . . . . . . . . . . . . . 5
3 Framing and Clearances
A. Select Appliance Location . . . . . . . . . . . . . . . . . . . . . . 6
B. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
C. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . 8
5 Appliance Preparation
A. Remove Logs, Ember Bed and Shipping Cover . . . . . 9
B. Securing and Leveling Appliance . . . . . . . . . . . . . . . . 9
6 Gas Information
A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . 11
E. Valve Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7 Electrical Information
A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . 13
B. Connecting to the Appliance . . . . . . . . . . . . . . . . . . . 13
C. Intellifi re Ignition System Wiring . . . . . . . . . . . . . . . . 13
8 Finishing
A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9 Appliance Setup
A. Remove the Shipping Materials . . . . . . . . . . . . . . . . 15
B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . .15
C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
D. Lava Rock, Ember Bed, Grate Assembly & Placement .
15
E. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . 16
F. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
G. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
10 Operating Instructions
A. Before Lighting Appliance . . . . . . . . . . . . . . . . . . . . . 18
B. Lighting the Appliance . . . . . . . . . . . . . . . . . . . . . . . . 19
C. After the Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . 20
D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . 20
11 Troubleshooting
A. Intellifi re Ignition System . . . . . . . . . . . . . . . . . . . . . . 21
12 Maintaining and Servicing the Appliance
A. Valve Service and Replacement . . . . . . . . . . . . . . . . 23
B. Maintenance and Service Tasks: . . . . . . . . . . . . . . . . 25
13 Reference Materials
A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . 26
B. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
C. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . .36
Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05 3
1
Listing and Code Approvals
A. Appliance Certifi cation
MODELS: Dakota 42, Dakota 42H
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Vented Gas Appliance
STANDARD: ANSI Z21.50-2000—CSA2.22-M00
This product is listed to ANSI standards for “Vented Gas
Fireplaces” and applicable sections of “Gas Burning Heating
Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.
B. Glass Specifi cations
Hearth & Home Technologies appliances manufactured with
tempered glass may be installed in hazardous locations such
as bathtub enclosures as defi ned by the Consumer Product
Safety Commission (CPSC). The tempered glass has been
tested and certifi ed to the requirements of ANSI Z97.1 and
CPSC 16 CFR 1202 (Safety Glazing Certifi cation Council
SGCC# 1595 and 1597. Architectural Testing, Inc. Reports
02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Section
1201.5 “Certifi cation and labeling requirements” which refers
to 15 U.S. Code (USC) 2063 stating “…Such certifi cate shall
accompany the product or shall otherwise be furnished to
any distributor or retailer to whom the product is delivered.”
Some local building codes require the use of tempered glass
with permanent marking in such locations. Glass meeting
this requirement is available from the factory. Please contact
your dealer or distributor to order.
C. BTU Specifi cations
Maximum
Models
Dakota 42 (NG) 61,000 25
Dakota 42 (LP) 52,000 44
Input BTUH
Orifi ce Size
(DMS)
D. High Altitude Installations
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
When installing this appliance at an elevation above 2000 ft,
it may be necessary to decrease the input rating by changing the existing burner orifi ce to a smaller size. Input rate
should be reduced by 4% for each 1000 ft above a 2000 ft
elevation in the U.S.A., or 10% for elevations between 2000
and 4500 ft in Canada. If the heating value of the gas has
been reduced, these rules do not apply. To identify the proper orifi ce size, check with the local gas utility.
If installing this appliance at an elevation above 4500 ft (in
Canada), check with local authorities.
WARNING
Do NOT use this appliance if any part has been under
water. Immediately call a qualifi ed service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
Note: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
4 Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05
2
Getting Started
2
A. Design and Installation Considerations
Note: This appliance must be installed outside.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional,
state and national codes and regulations.
• Consult insurance carrier, local building, fire
offi cials or authorities having jurisdiction about
restrictions, installation inspection, and permits.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed.
• Gas supply piping.
• Electrical wiring.
• Framing and fi nishing details.
C. Inspect Appliance and Components
WARNING
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
• Carefully remove the appliance and components from the
packaging.
• The gas logs may be packaged separately and must be
fi eld installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety and
benefi t.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Reciprocating saw Framing material
Pliers Hi temp caulking material
Hammer Gloves
Phillips screwdriver Framing square
Flat blade screwdriver Electric drill and bits (1/4 in.)
Plumb line Safety glasses
Manometer Voltmeter
Tape measure Level
Non-corrosive leak check solution
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
• Installation and use of any damaged appliance or
vent system component.
• Modifi cation of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass
door.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Any such action may cause a fi re hazard.
Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05 5
3
Framing and Clearances
3
Note:
• Illustrations refl ect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
WARNING
Fire Risk
Provide adequate clearance:
• Around air openings.
• To combustibles.
• For service access.
Locate appliance away from traffi c areas.
A. Select Appliance Location
When selecting a location for your appliance it is important to
consider the required clearances to walls (See Figure 3.1).
Note: If this surface is
inside the building’s
warm air envelope...
B
A
Note: For actual appliance dimensions refer to
Section 13.
...then this surface
must be an exterior
wall system.
G
FF
E
ABCDEFG
in. 24-3/4 24-1/8 48 49 5/8 1/2 1-1/2
mm 629 613 1219 1245 16 13 38
Figure 3.1 Appliance Locations
6 Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05
C
D
Framing Dimensions
ABCC
in. 24-1/8 43-7/8 49 43-7/8
mm 613 1114 1245 1114
B
A
Figure 3.2 Framing Dimensions
B. Clearances
WARNING
Fire Risk
Odor Risk
• Install appliance on hard metal or wood
surfaces extending full width and depth
of appliance.
• Do NOT install appliance directly on
carpeting, vinyl, tile or any combustible
material other than wood.
D
Header height.
C
Use only noncombustible
material below the top of
the top standoffs.
C. Mantel Projections
Free Standing Installation
Minimum
Clearance *
COMBUSTIBLE
STRUCTURE
WARNING
Fire Risk
• Locate and install appliance to all
clearance specifi cations in manual.
84 in.
(2134 mm)
min.
* This appliance can be installed a minimum of 6 in.
(152 mm) from a combustible structure unless the
structure is vinyl which requires a minimum
clearance of 48 in. (1219 mm)
Figure 3.3 Clearances to Mantels or Other Combustibles Above
Appliance
Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05 7
A
A
4
Termin ation Lo cations
4
A. Vent Termination Minimum Clearances
D
E
B
L
B
= FIREPLACE OPENING
FP
FP
F
FP
X
FP
= AIR SUPPLY INLET
FP
FP
O
P
G
R
H
(See Note 2)
B
M
I
FP
N
FP
Q
X
J or K
= AREA WHERE FIREPLACE IS NOT PERMITTED
A = 0 in. . . . . . . . . . clearances above grade,
veranda, porch, deck or
balcony.
B = 12 in. . . . . . . . . . clearances to window or door
that may be opened, or to
permanently closed window.
36 in . . . . . . . . . . vinyl windows or siding.
D** = 47 in. . . . . . . . . . vertical clearance to unventi-
lated soffit or to ventilated soffit
located above the terminal.
60 in. . . . . . . . . . vinyl clad soffits.
F = 9 in. . . . . . . . . . clearance to outside corner.
G* = 6 in. . . . . . . . . . clearance to inside corner.
48 in. . . . . . . . . . vinyl windows or siding.
H = 3 ft. (Canada) . not to be installed above a gas
meter/regulator assembly within
3 ft (914 mm) horizontally from
the center line of the regulator.
I = 3 ft. (USA)
6 ft. (Canada) . clearance to service regulator
vent outlet and electric service.
* 48 in. minimum for vinyl windows or vinyl siding.
** Not allowed for vinyl clad soffits.
*** a fireplace shall not open directly above a sidewalk or paved
driveway which is located between two single family dwellings
and services both dwellings.
**** only permitted if veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor, or if the screened
porch guidelines are followed.
Note 1: Local codes or regulations may require different clearances.
Note 2: Termination in an alcove space (spaces open only on one
side and with an overhang) are permitted with the dimensions
specified for vinyl or non-vinyl siding and soffits. 1) There must
be a 3 ft minimum between terminations or between the
fireplace and termination. 2) All mechanical air intakes within 10
ft of a termination must be a minimum of 3 ft below the fireplace
hood. 3) All gravity air intakes within 3 ft of the fireplace hood
must be a minimum of 1 ft below the termination.
Figure 4.1 Minimum Clearances
J = 9 in. (USA)
12 in. (Canada) . clearance to non-mechanical air
supply inlet to building or the
combustion air inlet to any other
appliance.
K = 3 ft. (USA)
6 ft. (Canada) . clearance to a mechanical air
supply inlet.
L*** = 54 in. . . . . . . . . . clearance above paved sidewalk
(See note 1) or a paved driveway located on
public property.
M**** = 47 in. . . . . . . . . . clearance under veranda, porch,
deck, balcony or overhang.
Not allowed: . . . . . . vinyl
N = 6 in. . . . . . . . . . non-vinyl siding.
P = 84 in.
Q
MIN
Dakota 10 feet 2 x Q
___________________________________________________________________________
1 additional termination cap Q + 3 feet 1 x Q
___________________________________________________________________________
2 additional termination caps Q + 6 feet 2/3 x Q
___________________________________________________________________________
3 additional termination caps Q + 9 feet 1/2 x Q
R
= (2 / # caps plus fireplace ) x Q
MAX
This fireplace is approved for installation onto screen porches with the
following guidelines:
Minimum porch area: 96 sq ft
Minimum ceiling height: 92 in.
Minimum of two walls must be screened
Minimum top of screen height, side walls: 6 ft 8 in.
Minimum screen area: 64 sq ft
Note 2: There may be some odor and small amounts of soot associated
with burning the Dakota on a screened porch. Ensuring good cross
draft ventilation and routine maintenance of the fireplace will maximize
comfort and cleanliness.
ACTUAL
R
MAX
ACTUAL
ACTUAL
ACTUAL
ACTUAL
CAUTION: If exterior walls are fi nished with vinyl siding, it is necessary to install the vinyl protector kit to the top of the exterior fi restop
(for all round termination caps). It is strongly recommended to use the vinyl protector kit whenever possible.
8 Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05
5
Appliance Preparation
CAUTION
B. Securing and Leveling Appliance
Sharp Edges
• Wear protective gloves
and safety glasses during
installation.
A. Remove Logs, Ember Bed and Shipping
Cover
Open the doors by sliding the handles toward the outside
edges of the doors (see Figure 5.1) Remove the ember bed
from in front of the grate. Remove the carton of logs from
their shipping location in the appliance.
Open
Open
WARNING
Fire Risk
• Prevent contact with sagging, loose
insulation.
• Do NOT install against vapor barriers or
exposed insulation.
The diagram shows how to properly position, level, and secure the appliance (see Figure 7.3). Nailing tabs are provided to secure the appliance to the framing members.
• Place the appliance into position on either a combustible
or non-combustible continuous fl at surface.
Note: Remove the top standoffs before sliding appliance
into position if using an FPS prefab enclosure.
• Level the appliance from side to side and front to back.
• Shim the appliance with non-combustible material, such
as sheet metal, as necessary.
• Bend out nailing tabs on each side.
• Keep nailing tabs fl ush with the framing.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
Figure 5.1 Door Operation
NAILING TABS
Figure 5.2 Proper Positioning, Leveling and Securing of an
Appliance
CAUTION
Do NOT notch into the framing around the appliance
spacers.
Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05 9
6
Gas Information
A. Fuel Conversion
Before making gas connections ensure appliance being installed is compatible with the available gas type.
Any natural or propane gas conversions necessary to meet
the appliance and locality needs must be made by a qualifi ed technician using Hearth & Home Technologies specifi ed
and approved parts.
B. Gas Pressure
Proper input pressures are required for optimum appliance
performance. Gas line sizing requirements need to be made
following NFPA51.
WARNING
Fire Risk
Explosion Risk
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
C. Gas Connection
Note: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualifi ed installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.)
Note: A listed (and Commonwealth of Massachusetts
approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and fl exible gas connector are connected to the 1/2 in.
(13 mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
Optional: A 5 ft fl exible gas line is availavle to those regions
which do not require black pipe to be used. See Service
Parts List (Section 13).
Note: Gas line MUST be run from right side of appliance.
WARNING
Fire Risk
Explosion Risk
Verify inlet pressures.
• High pressure may cause overfire
condition.
• Low pressure may cause explosion.
Install regulator upstream of valve if line
pressure is greater than 1/2 psig.
Pressure requirements for appliance are shown in table
below.
Pressure Natural Gas Propane
Minimum Inlet Pressure 5.0 inches w.c. 11.0 inches w.c.
Maximum Inlet Pressure 7.0 inches w.c. 11.0 inches w.c.
Manifold Pressure 3.5 inches w.c. 10.5 inches w.c.
These pressures can be verifi ed through the internal valve
access panels as shown in E. Valve Access.
WARNING
Gas Leak Risk
• Support control when attaching pipe to
prevent bending gas line.
Note: The gap between supply piping and gas access hole
may be plugged with non-combustible unfaced insulation
to prevent cold air infi ltration.
• Ensure that gas line does not come in contact with outer
wrap of appliance. Follow local codes.
• Incoming gas line should be piped into the valve
compartment and connected to the 1/2 in. connection on
the manual shutoff valve.
10 Heat-N-Glo Lifestyle Collection • Dakota 42/Dakota 42H • 4036-905 Rev I • 10/05
Loading...