Heat & Glo SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI Owner’s Manual
Models:
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-350TRS-IPI
Owner’s Manual
Installation and Operation
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency , or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
• Read, understand and follow
these instructions for safe
installation and operation.
DO NOT
DISCARD
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas fi tter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations
Congratulations on selecting a Heat & Glo gas appliance
—an elegant and clean alternative to wood burning
appliances. The Heat & Glo gas appliance you have
selected is designed to provide the utmost in safety,
reliability, and effi ciency.
As the owner of a new appliance, you’ll want to read and
carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all Cautions and
Warnings.
Homeowner Reference Information
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.
Your new Heat & Glo gas appliance will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of appliance products!
We recommend that you record the following pertinent
information about your appliance.
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on appliance: ____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
This product may be coveredby one or more ofthe following patents: (Nos produitssont couverts par un ouplusieurs des brevets suivants): (United States)
4593510,4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356,5341794, 5347983, 5429495,
5452708,5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485,5931661, 5941237, 594711 2,5996575, 6006743,6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2,
6729551, 6736133, 6748940, 6748942, D320652,D445174, D462436; (Canada)1297749, 2195264, 2225408;or other U.S. and foreignpatents pending (ou
autresbrevetsamericainsetetrangersenattente).
Type of Gas
Not for use with solid fuel .
(Ne doit pas entre utilise avec un combustible solide).
Ty pe of Gas (Sorte De Gaz) :
NATURA L GAS
Gas and Electric
Information
Minimum Permissible Gas Supply for Purpos es of Input Adjustment .
Approved Minimum (De Gaz) Acceptabl e 0. 0 in w. c. (Po. Col. d’eau)
Maximum Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau)
Maximum Manifold Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau)
Minimum Manifold Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau)
T o tal Electrical Requirements: 000V ac, 00Hz., less than 00 Ampere s
AL TI TUDE : 0-0000 FT . 0000-0000FT .
MAX. INPU T BTUH: 00,000 00,000
MIN. INPU T BTUH: 00,000 00,000
ORIFICE SIZE: #XXXXX #XXXXX
The model information regarding your specifi c appliance can be found on
the rating plate usually located in the control area of the appliance.
He at & Gl o, a of Hearth & Ho me Te chnologies, Inc.
20802 Kensington Boulevard, Lakeville, MN 5504 4
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CG A B149 installation codes. (Installer l’ appa re il selon les codes ou regl emen ts
lo caux ou , en l’absence de tels reglements, selon les codes d’in stallation CAN/CGA-B149.)
bran d
ANSI Z21X X-XXXX · CS A 2.XX-MXX · UL307B
IN CANADA
Mode l:
(Modele):
Serial
(Serie):
XXXXXXXX
XXXXXXXX
MADE IN US A
Model Number
Serial Number
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/082
Table of Contents
1 Listing and Code Approvals
A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4
E. Non-Combustible Materials Specifi cation. . . . . . . . . . . . . . 4
F. Combustible Materials Specifi cation . . . . . . . . . . . . . . . . . 4
G. Requirements for the Commonwealth of Massachusetts . . 5
2 Getting Started
A. Design and Installation Considerations . . . . . . . . . . . . . . . 6
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6
C. Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 6
3 Framing and Clearances
A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7
B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . . 8
C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
D. Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . . . 9
E. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . .11
5 Vent Information and Diagrams
A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
D. Use of Flex Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Vent Clearances and Framing
A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 25
B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 25
C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 26
7 Appliance Preparation
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 29
9 Gas Information
A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
10 Electrical Information
A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 40
B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 40
C. Intellifi re Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 40
D. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 42
E. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 42
11 Finishing
A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
C. Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
D. Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
12 Appliance Setup
A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 48
B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
D. Lava Rock, Mineral Wool/Ember Placement . . . . . . . . . . 48
E. Install Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
F. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
G. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
H. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
13 Operating Instructions
A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 57
B. Lighting Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
C. After Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 59
14 Troubleshooting
A. Intellifi re Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 60
15 Maintaining and Servicing Appliance
A. Maintenance Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
8 Installing Vent Pipe
A. Assembly of Vent Sections (DVP Pipe) . . . . . . . . . . . . . . 30
B. Disassembly of Vent Sections (DVP Pipe) . . . . . . . . . . . . 32
C. Installing Heat Shield and Horizontal Termination Cap (DVP
Pipe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
D. Assembly of Vent Sections (SL pipe) . . . . . . . . . . . . . . . . 34
E. Installing Wall Shield Firestops and Horizontal Termination
Cap (SL Pipe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
F. Installing Roof Flashing and Vertical Termination Cap . . . 36
Î = Contains updated information.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 3
16 Reference Materials
A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 64
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 65
C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
D. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 79
E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
1
1
Listing and Code Approvals
A. Appliance Certifi cation
MODELS: SL-750TRS-IPI-E,SL-550TRS-IPI-E,
SL-350TRS-IPI
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88a-2007 • CSA 2.33a-2007
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Glass Specifi cations
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defi ned by the Con-
sumer Product Safety Commission (CPSC). The tempered
glass has been tested and certifi ed to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certifi cation Council SGCC# 1595 and 1597. Architectur-
al Testing, Inc. Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Sec-
tion 1201.5 “Certifi cation and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certifi cate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
C. BTU Specifi cations
Models
U.S. (0-2000 ft.) or
Canada (2000-4500 ft.)
SL-750TRS-IPI-E (NG)
SL-750TRS-IPI-E (LP)
SL-550TRS-IPI-E (NG)
SL-550TRS-IPI-E (LP)
SL-350TRS-IPI (NG)
SL-350TRS-IPI (LP)
U.S. 30,800 20,200 #37
Canada 27,720 18,180 #38
U.S. 30,700 23.300 #52
Canada 27,630 20,970 #53
U.S. 27,300 18,200 #40
Canada 24,570 16,380 #41
U.S. 25,100 18,300 #53
Canada 22,590 16,470 #54
U.S. 20,500 14,400 #44
Canada 18,450 12,960 #45
U.S. 20,000 14,900 #55
Canada 18,000 13,410 #56
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifi ce
Size
(DMS)
D. High Altitude Installations
U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in
the U.S.A. and Canada.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating
by changing the existing burner orifi ce to a smaller size.
Input rate should be reduced by 4% for each 1000 feet
above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the
heating value of the gas has been reduced, these rules
do not apply . To identify the proper orifi ce size, check with
the local gas utility.
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
WARNING
Do NOT use this appliance if any part has been under water.
Immediately call a qualifi ed service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Note: This installation must conform with local codes. In the
absence of local c odes you must comply w ith the National
Fuel Gas Code, ANSI Z223.1 -latest edition in the U.S.A. and
the CAN/CGA B149 Installation Codes in Canada.
Heat & Glo Quality Systems
registered by SGS ICS
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/084
E. Non-Combustible Materials Specifi cation
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof. Materials that are reported as passing ASTM E 136, Standard
Test Method for Behavior of Materials in a Vertical
Tube Furnace at 750ºC, shall be considered non-com-
bustible materials.
F. Combustible Materials Specifi cation
Materials made of or surfaced with wood, compressed
paper, plant fi bers, plastics, or other material that can ig-
nite and burn, whether fl ame proofed or not, or whether
plastered or unplastered shall be considered combustible
materials.
Note: The following requirements reference various
Massachuset ts and national codes not contained in this
document.
G. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above fi nished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfi ed:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fi tter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the fl oor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fi tter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualifi ed licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
fl oor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equip-
ment Not Required To Be Vented” in the most current
edition of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fu-
eled equipment installed in a room or structure separate from the dwelling, building or structure used in
whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the fl ue gases, but identifi es
“special venting systems”, the following requirements
shall be satisfi ed by the manufacturer:
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certifi ed.
Signage
A metal or plastic identifi cation plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 5
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Ap-
proved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
2
2
Getting Started
A. Design and Installation Considerations
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside. No additional outside air source is required.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult local building, fi re offi cials or authorities having jurisdic-
tion about restrictions, installation inspection, and permits.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed.
• The vent system confi guration to be used.
• Gas supply piping.
• Electrical wiring.
• Framing and fi nishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
C. Inspect Appliance and Components
WARNING
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and trim doors are shipped
in separate packages.
• The gas logs may be packaged separately and must be
fi eld installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefi t.
WARNING
WARNING
Keep appliance dry.
• Mold or rust may cause odors.
• Water may damage controls.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Reciprocating saw Framing material
Pliers Hi temp caulking material
Hammer Gloves
Phillips screwdriver Framing square
Flat blade screwdriver Electric drill and bits (1/4 in.)
Plumb line Safety glasses
Level 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Manometer Voltmeter
Tape measure Noncorrosive leak check solution
One 1/4 inch female connection (for optional fan).
• Installation and use of any damaged appliance or vent
system component.
• Modifi cation of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fi re hazard.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/086
3
3
Framing and Clearances
Note:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
A. Selecting Appliance Location
When selecting a location for your appliance it is important to
consider the required clearances to walls (see Figure 3.1).
A
L
F
A
C
WARNING
Fire Risk
Provide adequate clearance:
• Around air openings
• To combustibles
• For service access
Locate appliance away from traffi c areas.
NOTE: For actual appliance dimensions refer to Section 16.
N
E
D
C
F
A
In addition to these framing dimensions, also reference the following sections:
• Clearances and Mantel Projections (Section 3.C and 3.D)
• Vent Clearances and Framing (Section 6).
K
J
J
M
Models A B C D
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-350TRS-IPI
in. 45-1/2 42 64-3/8
mm 1155 1067 1635 25 13 1155 1635 413 1232 1737 422 191 229
in. 42 37 59-1/2 1 1/2 44 62-1/4 16-1/4 48-1/2 68-3/4 15-1/16 7-1/2 7-1/8
mm 1067 940 1511 25 13 1117 1581 413 1232 1737 383 191 181
in. 39-1/2 34 55-7/8 1 1/2 44 62-1/4 16-1/4 48-1/2 68-3/4 13-1/2 7-1/2 6
mm 1003 864 1413 25 13 1117 1581 413 1232 1737 343 191 152
See Section
E for Alcove
Installation
B
I
E
Min.FMin.
1 1/2 45-1/2 64-3/8 16-1/4 48-1/2 68-3/4 16-5/8 7-1/2 9
GH I JKL M N
H
G
G
Figure 3.1 Appliance Locations
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 7
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gas appliance and/or its vent system. Vertical vents that
run on the outside of a building may be, but are not required to be, installed inside a chase.
Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST
be checked.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
Walls, ceiling, base plate and cantilever fl oor of the chase
should be insulated. Vapor and air infi ltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infi ltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
To further prevent drafts, the wall shield and ceiling
fi restops should be caulked with high temperature caulk
to seal gaps. Gas line holes and other openings should
be caulked with high temp caulk or stuffed with unfaced
insulation. If the appliance is being installed on a cement
slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.
C. Clearances
WARNING
Fire Risk.
Odor Risk.
• Install appliance on hard metal or wood surfaces
extending full width and depth of appliance.
• Do NOT install appliance directly on carpeting,
vinyl, tile or any combustible material other than
wood.
WARNING
Fire Risk.
• Construct chase to all clearance specifi cations
in manual.
• Locate and install appliance to all clearance
specifi cations in manual.
A
B
C
D
ABCDEFGHIJ
Models
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-350TRS-IPI
Inches
Millimeters
Inches
Millimeters
Inches
Millimeters
DVP PIPE SL PIPE
Rough
Opening
(Width)
Rough
Opening
(Width)
10 8-5/8 38-1/4 28-1/4 16-1/4 42 32 0 0 1/2 1/2 36
254 219 971 699 413 1067 813 0 0 13 13 915
10 8-5/8 34-3/4 28-1/4 16-1/4 37 32 0 0 1/2 1/2 36
254 219 882 699 413 940 813 0 0 13 13 915
10 8-5/8 32-3/4 28-1/4 16-1/4 34 32 0 0 1/2 1/2 36
254 219 832 699 413 864 813 0 0 13 13 915
Rough
Opening
(Height)
* Dimension when rear venting with one 90º elbow
Figure 3.2 Clearances to Combustibles (Vertical Venting)
*DVP PIPE
Rough
Opening
(Depth)
SL PIPE
Rough
Opening
(Depth)
F
Rough
Opening
(Width)
J
Clearance
to Ceiling
G
Combustible
Floor
MEASURE FROM
TOP OF UNIT OPENING
OR FROM TOP OF HOOD
I
Combustible
Flooring
Behind
Appliance
E
H
Sides of
Appliance
Front of
Appliance
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/088
D. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions.
Some hearth systems will elevate the appliance off the fl oor at a given dimension. For example, if appliance will be used with a
Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation will also have to be added to the
following: Extension Wall Hole referenced in Figure 6.3 (Exterior W all Hole) and Rough Opening Height (header height) referenced in
Figure 3.2. NOTE: Finished fl oor thickness should also be considered when determining installation dimensions.
MODEL DESCRIPTION PART #
KENWOOD CABINET KDC44SBP 0 27 3/8 in.
SL-350
SL-550
SL-750
KENWOOD CABINET W/ BASE KDC44SBP W/ HTKDC44SBP 9 1/4 in. 27 3/8 in.
KENWOOD CORNER CABINET KDA44SBP 0 27 3/8 in.
KENWOOD CORNER CABINET W/ BASE KDA44SBP W/ HTKDA44SBP 9 1/4 in. 27 3/8 in.
KENWOOD CABINET KDC44SBP 0 29-3/8 in.
KENWOOD CABINET W/ BASE KDC44SBP W/ HTKDC44SBP 9-1/4 in. 29-3/8 in.
KENWOOD CORNER CABINET KDA44SBP 0 29-3/8 in.
KENWOOD CORNER CABINET W/ BASE KDA44SBP W/ HTKDA44SBP 9-1/4 in. 29-3/8 in.
KENWOOD MANTEL AFKDMPA 0 (See Note 3) 27-3/8 in.
KENWOOD MANTEL W/ BASE AFKDMPA W/ HTKDMPA 9 1/4 in. 29-3/8 in.
LAURENT SURROUND LAURENT-32 1-1/2 in. N/A
CAMDEN SURROUND CAM550PG 0 N/A
CAMDEN SURROUND W/HEARTH CAM550PGH 1-3/4 in. N/A
CAMDEN SURROUND W/MANTEL CAMM550PG 0 N/A
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND ESSEX550PG 0 N/A
ESSEX SURROUND W/HEARTH ESSEX550PGH 1-3/4 in. N/A
ESSEX SURROUND W/MANTEL ESSEXM550PG 0 N/A
ESSEX SURROUND W/MANTEL &
HEARTH
LUNA SURROUND LUNA-32-GY 1-1/16 in. N/A
MONROE SURROUND MON550PG 0 N/A
MONROE SURROUND W/HEARTH MON550PGH 1-3/4 in. N/A
MONROE SURROUND W/MANTEL MONM550PG 0 N/A
MONROE SURROUND W/MANTEL &
HEARTH
KENWOOD CABINET KDC48DBP 0 32-7/8 in.
KENWOOD CABINET W/ BASE KDC48DBP W/ HTKDC48DBP 9-1/4 in. 32-7/8 in.
KENWOOD CORNER CABINET KDA48SBP 0 32-7/8 in.
KENWOOD CORNER CABINET W/ BASE KDA48SBP W/ HTKDA48SBP 9-1/4 in. 32-7/8 in.
KENWOOD MANTEL AFKDMPB 0 (See Note 3) 27-3/8 in.
KENWOOD MANTEL W/ BASE AFKDMPB W/ HTKDMPB 9-1/4 in. 29-3/8 in.
LAURENT SURROUND LAURENT-36 1-1/2 in. N/A
CAMDEN SURROUND CAM36PG 0 N/A
CAMDEN SURROUND W/HEARTH CAM36PGH 1-3/4 in. N/A
CAMDEN SURROUND W/MANTEL CAMM36PG 0 N/A
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND ESSEX36PG 0 N/A
ESSEX SURROUND W/HEARTH ESSEX36PGH 1-3/4 in. N/A
ESSEX SURROUND W/MANTEL ESSEXM36PG 0 N/A
ESSEX SURROUND W/MANTEL &
HEARTH
LUNA SURROUND LUNA-36-GY 1-1/16 in. N/A
MONROE SURROUND MON36PG 0 N/A
MONROE SURROUND W/HEARTH MON36PGH 1-3/4 in. N/A
MONROE SURROUND W/MANTEL MONM36PG 0 N/A
MONROE SURROUND W/MANTEL &
HEARTH
CAMM550PGH 1-3/4 in. N/A
ESSEXM550PGH 1-3/4 in. N/A
MONM550PGH 1-3/4 in. N/A
CAMM36PGH 1-3/4 in. N/A
ESSEXM36PGH 1-3/4 in. N/A
MONM36PGH 1-3/4 in. N/A
ELEVATED APPLIANCE
DIMENSION
See Note 1
NOTE 1. Add dimensions to Exterior Wall Hole (Figure 6.3) and Rough Opening Height (Figure 3.2).
NOTE 2. Verify Marble Cut Lengths on site prior to cutting.
NOTE 3. Dimensions assume use of a 3/4 in. Hearth Pad.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 9
MARBLE LEG CUT
LENGTH
See Note 2
E. Mantel Projections
All measurements are in inches.
12
11
10
9
8
7
6
5
4
3
8
7
6
5
4
TOP OF HOOD OR FIREPLACE OPENING
Figure 3.3 Clearances to mantels or other combustibles
above appliance
11
10
9
CEILING
13
12
32
1/2 IN.
MINIMUM
2-7/8 IN.
MINIMUM
Note: Clearance from opening
to perpendicular wall.
Figure 3.5 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
3 FT. MAXIMUM
1/2 in.
3-1/2 in.
NON-COMBUSTIBLE ZONE
1/2 in.
SHEETROCK
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
3 IN.
MINIMUM
5-3/8 IN.
MINIMUM
Note: Clearance from opening
to perpendicular wall.
Figure 3.6 Wall Projection (Acceptable on one side of opening.)
UNLIMITED
Figure 3.4 Non-Combustible Zone
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0810
4
4
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may
ignite.
• Restricted air fl ow affects burner operation.
WARNING
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specifi ed.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fi re.
Measure vertical clearances from this surface.
HORIZONTAL
OVERHANG
2 FT.
MIN.
GAS DIRECT VENT
TERMINATION CAP
Roof Pitch H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 4.2 Minimum height from roof to lowest discharge
opening
20 INCHES MIN.
LOWEST
DISCHARGE
OPENING
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
X
12
ROOF PITCH
VERTICAL
WALL
IS X/ 12
Measure horizontal clearances from this surface.
(See Figure 4.4 for specifi c clearances)
Figure 4.1
Figure 4.2 specifi es minimum vent heights for various
pitched roofs.
GAS, WOOD OR FUEL
OIL TERMINATION
GAS
TERMINATION
C
A
Gas
Termination
A 6 in. 20 in. min. Horizontal distance between terminations
B 20 in. 24 in. min. Distance to perpendicular wall
C 18 in. 18 in. Vertical distance between terminations
Figure 4.3 Multiple Vertical Termination
Wood & Fuel Oil
Termination
B
Comments
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 11
V
R
M
P
Q
(See Note 2)
T
S
Electrical
V
Service
V
N
S
V
D*
= VENT TERMINAL
V
A = 12 inches.................clearances above grade, veranda,
(See Note 1)
X
= AIR SUPPLY INLET
porch, deck or balcony
B = 12 inches.................clearances to window or door
that may be opened, or to permanently closed window. (Glass)
D* = 18 inches.................vertical clearance to unventilated
soffi t or to ventilated soffi t located
above the terminal
*30 inches ................for vinyl clad soffi ts and below
electrical service
F = 9 inches..................clearance to outside corner
G = 6 inches...................clearance to inside corner
H = 3 ft. (Canada) ..........not to be installed above a gas
meter/regulator assembly within 3
feet (90 cm) horizontally from the
center-line of the regulator
I = 3 ft ...........................clearance to gas service regulator
vent outlet
J = 9 inches (U.S.A.)
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
K = 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (pow-
ered) air supply inlet
= AREA WHERE TERMINAL IS NOT PERMITTED
L** = 7 ft. ......................... clearance above paved
(See Note 1)
sidewalk or a paved driveway
located on public property
M*** = 18 inches................ cl earance under veranda, porch,
deck, balcony or overhang
42 inches ............... vinyl
S = 6 inches................. clearance from sides of electri-
(See Note 5)
cal service
T = 12 inches................ clearance above electrical
(See Note 5)
service
Alcove Applications
N = 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
P = 8 ft.
Q
MIN
1 cap 3 feet 2 x Q
2 caps 6 feet 1 x Q
3 caps 9 feet 2/3 x Q
4 caps 12 feet 1/2 x Q
Q
= # termination caps x 3 R
MIN
= (2 / # termination caps) x Q
MAX
R
MAX
ACTUAL
ACTUAL
ACTUAL
ACTUAL
ACTUAL
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the fl oor, or meets Note 2.
NOTE 1: On private property where termination is less than 7 feet above
a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specifi ed for
vinyl or non-vinyl siding and soffi ts. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
NOTE 3: Local codes or regulations may require different
clearances.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffi c areas.
NOTE 5: Location of the vent termination must not interfere with
access to the electrical service.
WARNING: In the U.S: V ent system termination is NOT permitted in
screened porches. Y ou must follow side wall, overhang and ground
clearances as stated in the instructions.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Heat & Glo assumes no responsibility for the improper performance
of the appliance when the venting system does not meet these
Figure 4.4 Minimum Clearances for Termination
requirements.
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0812
5
5
Vent Information and Diagrams
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol Description
V
First section (closest to appliance) of vertical length
1
Vertical
V
H
H
Second section of vertical length
2
First section (closest to appliance) of horizontal length
1
Second section of horizontal length
2
WARNING
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
Do NOT connect this gas appliance to a chimney
fl ue serving a separate solid-fuel or gas burning
appliance.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
May impair safe operation of this appliance or
other appliances connected to the fl ue.
B. Use of Elbows
CAUTION
ALL vent confi guration specifi cations MUST be followed.
• This product is tested and listed to these specifi cations.
• Appliance performance will suffer if specifi cations are not
followed.
12 in.
8-1/2 in.
8-1/2 in.
Horizontal
Figure 5.1
C. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
1. Pipe measurements are shown using the effective length
of pipe (see Figure 5.2).
2. Measurements are made from the appliance outer wrap,
not from the standoffs.
3. Horizontal terminations are measured to the outside
mounting surface (fl ange of termination cap) (see
Figure 4.1).
4. V ertical terminations are measured to bottom of termination cap.
5. Horizontal pipe installed level with no rise.
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
Two 45º elbows may be used in place of one 90º elbow . On
45º runs, one foot of diagonal is equal to 8.5 inches horizontal run and 8.5 inches vertical run. A length of straight
pipe is allowed between two 45º elbows (see Figure 5.1).
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 13
Effective
Height/Length
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610
Figure 5.2 DVP Pipe Effective Length
Pipe
DVP4 4 102
DVP6 6 152
DVP12 12 305
DVP24 24 610
DVP36 36 914
DVP48 48 1219
DVP6A 3 to 6 76 to 152
DVP12A 3 to 12 76 to 305
Effective Length
Inches Millimeters
D. Use of Flex Vent
The fl ex vent must be supported with
the spacing between support intervals
not exceeding 4 feet, with no more
than ½ inch sag between supports.
A support is required at each change
in venting direction, and in any location
where it is necessary to maintain the
necessary clearance to combustibles.
A simple “up and out” installation (Figure 5.3) requires only enough support
to maintain the necessary clearance
to combustibles. However, the vent attachment point and the fi restop loca-
tion are considered to be supports.
FLEX-VENT
3in.CLEARANCE
TERMINATION
CAP
1in.
CLEAR AN CE
Figure 5.3
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0814
E. Vent Diagrams
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling fi restops.
• ALWAYS maintain specifi ed clearances around venting and fi restop systems.
• Install wall shield and ceiling fi restops as specifi ed.
Failure to keep insulation or other material away from vent pipe may cause fi re.
1. Top Vent - Horizontal Termination Venting
One Elbow
Note: Use SL-D Series
components only.
Note: There MUST be a 25%
reduction in total H when using
fl ex vent except when using the
simple up and out installation
(see Figure 5.3).
WARNING
WARNING
Maximum
H
V Minimum
90º Elbow 1-1/2 ft. 457 mm 1 ft. 305 mm
1/2 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm
1-1/2 ft. 457 mm 3 ft. 914 mm 3 ft. 914 mm
2-1/2 ft. 762 mm 5 ft. 1-1/2 m 5 ft. 1-1/2 m
3-1/2 ft. 1.1 m 7 ft. 2.1 m 7 ft. 2.1 m
4-1/2 ft. 1.4 m 15 ft. 4.6 m 15 ft. 4.6 m
V1 + H1 Maximum= 40 ft. (12.2 m)
SL-350TRS-IPI SL-550, SL-750TRS-E
Maximum= 15 ft. (4.6 m)
H
1
1
Fire Risk.
• When using SL-HRC-SS and SL-HRC-ZC-SS
termination caps on top vented fi replaces, a one
foot minimum vertical vent section is required
before installing fi rst elbow.
• When using DVP-TB1 termination cap on top vented
Î
fi replaces, a three foot minimum vertical vent section is
required before installing fi rst elbow.
H
1
V
1
Figure 5.4
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 15
Two Elbows
Note: Use SL-D Series
components only.
1/2 ft. 152 mm 1 ft. 305 mm
Note: There MUST be a 25%
reduction in total H when using
fl ex vent except when using the
simple up and out installation
(see Figure 5.3).
1-1/2 ft. 457 mm 2 ft. 610 mm
2-1/2 ft. 762 mm 4 ft. 1.2 m
3-1/2 ft. 1.1 m 6 ft 1.8 m
4-1/2 ft. 1.4 m 14 ft. 4.3 m
WARNING
Fire Risk.
• When using SL-HRC-SS and SL-HRC-ZC-SS
termination caps on top vented fi replaces, a one
foot minimum vertical vent section is required
before installing fi rst elbow.
• When using DVP-TB1 termination cap on top vented
Î
fi replaces, a three foot minimum vertical vent section is
required before installing fi rst elbow.
V Minimum
SL-350TRS-IPI, SL-550TRS-E, SL-750TRS-E
90º Elbow NOT ALLOWED
H1 + H2 Maximum= 14 ft. (4.3 m)
V1 + H1 + H2 Maximum= 40 ft. (12.2 m)
H Maximum
Figure 5.5
H
H
1
2
V
1
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0816
1. Top Vent - Horizontal Termination - (continued)
Three Elbows
V1 Minimum
Elbow only 1-1/2 ft. 457 mm 2 ft. 610 mm 1 ft. 305 mm 2 ft. 610 mm * *
1/2 ft. 152 mm 2 ft. 610 mm 4 ft. 1.2 m 2 ft. 610 mm 4 ft. 1.2 m * *
1-1/2 ft. 457 mm 3 ft. 914 mm 6 ft. 1.8 m 3 ft. 914 mm 6 ft. 1.8 m * *
2-1/2 ft. 762 mm 5 ft. 1.5 m 10 ft 3.0 m 5 ft. 1.5 m 10 ft. 3.0 m * *
3-1/2 ft. 1.1 m 7 ft. 2.1 m 14 ft. 4.3 m 7 ft. 2.1 m 14 ft. 4.3 m * *
4-1/2 ft. 1.4 m 14 ft. 4.3 m 14 ft. 4.3 m 14 ft. 4.3 m 14 ft. 4.3 m * *
Note: Use SL-D Series
components only.
H1 Maximum H1 + H2 Maximum H1 Maximum H1 + H2 Maximum V2V1 + V2 Minimum
Model: SL-350TRS-IPI Models: SL-550TRS-IPI-E, SL-750TRS-IPI-E * *
*No specifi c restrictions on this value EXCEPT V1 + V2 + H1 + H2 CANNOT exceed 40 ft. (12.2 m)
V1 + H1 + V2 + H2 Maximum = 40 ft. (12.2 m)
H
2
Note: There MUST be a 25%
reduction in total H when using
fl ex vent except when using the
simple up and out installation
(see Figure 5.3).
H
1
V
2
WARNING
Fire Risk.
• When using SL-HRC-SS and SL-HRC-ZC-SS
termination caps on top vented fi replaces, a one
foot minimum vertical vent section is required
before installing fi rst elbow.
V
1
Figure 5.6
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 17
2. Top Vent - Vertical Termination
No Elbow
Note: Use SL-D Series
components only.
Note: If installing a vertical vent/termination off the top of
the appliance, the optional vertical termination baffl e may
be needed.
V1 = 44 ft. Max. (13.4 m)
CAP
Exhaust restrictor Instructions
1. Install the exhaust restrictor over the center of the exhaust outlet in the fi rebox (see Figure 5.8).
2. Center the exhaust restrictor in the open end of the
exhaust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self tapping screws
provided in the appliance manual bag.
INNER HEAT SHIELD
To access the
exhaust openings,
remove the inner
heat shield. To
remove inner heat
shield, remove the
two screws.
Figure 5.7
V
1
Top Vent Application
Exhaust restrictor
Rear Vent Application
Exhaust restrictor
Note: Be sure to reinstall the inner heat
shield after exhaust
restrictor installation.
Exhaust restrictors are recommended for these vertically terminated products which have excessive draft.
Exhaust restrictors will compensate for high draft, and
restore visual fl ame height. If the vent confi guration has
a total vertical of 15-44 feet, an exhaust restrictor may
be needed. The exhaust restrictor can be located in the
appliance manual bag.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0818
Figure 5.8
2. Top Vent - Vertical Termination - (continued)
Two 90º Elbows
Maximum H1 Maximum V2V1 + V2 Minimum
H
V1 Minimum
90º Elbow 1-1/2 ft. 457 mm 1 ft. 305 mm * *
1/2 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm * *
1 ft. 305 mm 2-1/2 ft. 762 mm 2-1/2 ft. 762 mm * *
2 ft. 610 mm 4 ft. 1.2 m 4 ft. 1.2 m * *
3 ft. 914 m 6 ft. 1.8 m 6 ft. 1.8 m * *
4 ft. 1.2 m 8 ft. 2.4 m 8 ft. 2.4 m * *
5 ft. 1.5 m 15 ft. 4.6 m 15 ft 4.6 m * *
*No specifi c restrictions on this value EXCEPT V1 + V2 + H
1
SL-350TRS-IPI SL-550TRS-E, SL-750TRS-E * *
Maximum= 15 ft. (4.6 m)
H
1
V1 + V2 + H Maximum = 40 ft. (12.2 m)
CANNOT exceed 40 ft. (12.2 m)
1
V
Note: Use SL-D Series
components only.
H
1
2
V
1
Note: There MUST be a 25%
reduction in total H when using
fl ex vent except when using the
simple up and out installation
(see Figure 5.3).
Figure 5.8
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 19
2. Top Vent - Vertical Termination - (continued)
Three 90º Elbows
H
Note: Use SL-D Series
components only.
Note: There MUST be a 25%
reduction in total H when using
fl ex vent except when using the
simple up and out installation
(see Figure 5.3).
1/2 ft.. 152 mm 1 ft. 305 mm * * * *
1-1/2 ft. 457 mm 2 ft. 610 mm * * * *
2-1/2 ft. 762 mm 4 ft. 1.2 m * * * *
3-1/2 ft. 1.1 m 6 ft. 1.8 m * * * *
4-1/2 ft. 1.4 m 14 ft. 4.3 m * * * *
V
1
90º Elbow 0 0 1-1/2 ft. 457 mm 1-1/2 ft. 457 mm
*No specifi c restrictions on this value EXCEPT V1 + V2 + H1 + H
ALL MODELS
+ H
Maximum V
1
2
H
Maximum = 14 ft. (4.3 m)
1
2
CANNOT exceed 40 ft. (12.2 m).
V1 + V2 Minimum
2
V
2
H
1
V
H
2
1
Figure 5.9
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0820
2. Top Vent - Vertical Termination - (continued)
Four 90º Elbows
V1 Min. H1 Max. V2 Min. H2 Max. V3 Min.
1-1/2 ft. 457 mm 4 ft. 1.2 m 4 ft. 1.2 m 4 ft. 1.2 m 3-1/2 ft. 1.0 m
V
+ V2 + V
1
V
3
H
2
+ H2 Maximum= 40 ft. (12.2 m)
3 + H1
V
2
Note: Use SL-D Series
components only.
Note: There MUST be a 25%
reduction in total H when using
fl ex vent except when using the
simple up and out installation
(see Figure 5.3).
H
1
V
1
Figure 5.17
Figure 5.17
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 21
3. Rear Vent - Horizontal Termination
No Elbow
Note: Use DVP Series
components only.
= 24 in. (610 mm) Maximum
H
1
Two 90º Elbows
Note: Use DVP Series
components only.
90-DEGREE ELBOWS
H
1
Use two 90º elbows for corner installations.
The use of two 90º elbows in a corner installation
will affect space requirements.
Figure 5.10
Two 90º Elbows
Note: Use DVP Series
components only.
H
Figure 5.11
H1 Maximum V1 Minimum H
1-1/2 ft. 457 mm
3-1/2 ft. 1.1 m 1 ft. 305 mm 3 ft. 914 mm 6-1/2 ft. 2.0 m
5-1/2 ft. 1.7 m 2 ft. 610 mm 5 ft. 1.5 m 10-1/2 ft. 3.2 m
7-1/2 ft. 2.3 m 3 ft. 914 mm 6-1/2 ft. 2.1 m 14 ft. 4.3 m
2
Back to Back
Elbows
H
Maximum = 7-1/2 ft. (2.3 m)
1
H1 + H2 Maximum = 14 ft. (4.3 m)
V1 + H1 + H2= 40 ft. (12.2 m)
V
1
1 ft. 305 mm 2-1/2 ft. 762 mm
2
H1 + H2 Maximum
Figure 5.12
H
1
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0822
3. Rear Vent - Horizontal Termination - (continued)
Three Elbows
Note: Use DVP Series
components only.
INSTALLED
HORIZONTALLY
H
3
H1 Maximum V1 Minimum H2+ H
1-1/2 ft. 457 mm
Back to Back
Elbows
1 ft. 305 mm 2-1/2 ft. 762 mm
3
H1+ H2+ H
Maximum
3
3-1/2 ft. 1.1 m 1 ft. 305 mm 2 ft. 610 mm 5-1/2 ft. 1.7 m
5-1/2 ft. 1.7 m 2 ft. 610 mm 4 ft. 1.2 m 9-1/2 ft. 2.9 m
7-1/2 ft. 2.3 m 3 ft. 914 mm 6 ft. 1.8 m
H
Maximum = 7-1/2 ft. (2.3 m)
1
13-1/2
ft.
4.1 m
H1 + H2 + H3 Maximum =13-1/2 ft. (4.1 m)
V1 + H1 + H3= 40 ft. (12.2 m)
H
2
V
1
Figure 5.13
4. Rear Vent - Vertical Termination
One Elbow
Note: Use DVP Series
components only.
V
1
H
1
V1 Minimum H1 Maximum
Elbow Only 1-1/2 ft. 457 mm
1 ft. 305 mm 3-1/2 ft. 1.1 m
2 ft. 610 mm 5-1/2 ft. 1.7 m
3 ft. 914 mm 7-1/2 ft. 2.3 m
H
Maximum = 7-1/2 ft. (2.3 m)
1
V1 + H1 Maximum = 40 ft. (12.2 m)
H
1
Figure 5.14
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/08 23
4. Rear Vent - Vertical Termination - (continued)
Two Elbows
Note: Use DVP Series
components only.
Figure 5.15
Three Elbows
Note: Use DVP Series
components only.
H1+ H
Maximum V1 Minimum
2
1/2 ft. 152 mm Back to Back Elbows
2-1/2 ft. 762 mm 1 ft. 305 mm
4-1/2 ft. 1.4 m 2 ft. 610 mm
6-1/2 ft. 2.0 m 3 ft. 914 mm
H Maximum = 6-1/2 ft. (2 m)
V
+ H1 + H2 Maximum = 40 ft. (12.2 m)
V
1
INSTALLED
HORIZONTALLY
H
2
H
1
H1 Maximum V1 Minimum H
1-1/2 ft. 457 mm
Back to Back
Elbows
1
2
H1 + H2 Maximum
1 ft. 305 mm 2-1/2 ft. 762 mm
3-1/2 ft. 1.1 m 1 ft. 305 mm 3 ft. 914 mm 6-1/2 ft. 2.0 m
5-1/2 ft. 1.2 m 2 ft. 610 mm 5 ft. 1.5 m 10-1/2 ft. 3.2 m
7-1/2 ft. 2.3 m 3 ft. 914 mm 7 ft. 2.1 m 14-1/2ft. 4.4 m
Maximum = 7-1/2 ft. (2.3 m)
H
V
2
V1 + V2 + H1 + H2 Maximum = 40 ft. (12.2 m)
1
Figure 5.16
H
2
V
1
H
1
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. D • 2/0824
Loading...