Heat & Glo RED40ST User Manual

Models:
RED40
RED40ST

Owner’s Manual

Installation and Operation

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating
and maintenance
instructions included.

WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.

• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

- If you cannot reach your gas supplier, call

the fi re department.

• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.

This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated
on the rating plate.

• Read, understand and follow
these instructions for safe
installation and operation.

DO NOT

DISCARD

• Leave this manual with
party responsible for use
and operation.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during
operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as
fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable
materials.

• Keep clothing, furniture, draperies and other fl ammable
materials away.

This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.

See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.

Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

1

Not Not for for use use with with solid solid fuel.fuel.
((Ne Ne doit doit pas pas entre entre utilise utilise avec avec un un combustible combustible solide).solide).

This This appliance appliance must must be be installed installed in in accordance accordance with with local local codes, codes, if if any; any; if if not, not, follow follow ANSI ANSI Z223.1Z223.1
in in the the USA USA or or CAN/CGA CAN/CG A B149 B149 installation installation codes. codes. (Installer (Installer l’appareil l’appareil selon selon les les codes codes ou ou reglementsreglements

locaux locaux ou, ou, en en l’absence l’absence de de tels tels reglements, reglements, selon selon les les codes codes d’installation d’installation CAN/CGA-B149.)CAN/CGA-B149.)

Type Type of of Gas Gas (Sorte (Sorte De De Gaz)Gaz)::

NNAATURALTURAL GASGAS

MADE MADE IN IN USAUSA

Minimum Minimum Permissible Permissible Gas Gas Supply Supply for for Purposes Purposes of of Input Input Adjustment.Adjustment.
Approved Approved Minimum Minimum (De (De Gaz) Gaz) AcceptableAcceptable 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)
Maximum Maximum Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)
Maximum Maximum Manifold Manifold Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)
Minimum Minimum Manifold Manifold Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Model:Model:

(Modele):(Modele):

SerialSerial

(Serie):(Serie):

ANSI ANSI Z21XX-XXXX Z21XX-XXXX · · CSA CSA 2.XX-MXX 2.XX-MXX · · UL307BUL307B

XXXXXXXXXXXXXXXX

IN IN CANADACANADA
ALTITUDE:ALTITUDE: 0-0000 0-0000 FT.FT. 0000-0000FT.0000-0000FT.
MAX. MAX. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000
MIN. MIN. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000
ORIFICE ORIFICE SIZE:SIZE: #XXXXX#XXXXX #XXXXX#XXXXX

XXXXXXXXXXXXXXXX

Total Total Electrical Electrical Requirements: Requirements: 000Vac, 000Vac, 00Hz., 00Hz., less less than than 00 00 AmperesAmperes

Heat & Glo, a brand of Hearth & Home Technologies, Inc.
7571 215th Street West, Lakeville, MN 55044

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas fi replace, an
elegant and clean alternative to wood burning fi replaces.
The Heat & Glo gas fi replace you have selected is designed
to provide the utmost in safety, reliability, and effi ciency.

As the owner of a new fi replace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.

Homeowner Reference Information

This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.

The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.

Your new Heat & Glo gas fi replace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fi replace products!

We recommend that you record the following pertinent
information about your fi replace.

Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on fi replace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________

Listing Label Information/Location

Type of Gas

Gas and Electric
Information

The model information regarding your specifi c fi replace can be found on
the rating plate usually located in the control area of the fi replace.

Model Number

Serial Number

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/122

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7

E. Non-Combustible Materials Specifi cation. . . . . . . . . . . . . . 7

F. Combustible Materials Specifi cation . . . . . . . . . . . . . . . . . 7

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

H. Requirements for the Commonwealth of Massachusetts . . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10

E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

F. Remote Controls, Wall Controls and Wall Switches . . . . . 10

G. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10

H. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11

I. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

J. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks-Qualifi ed Service Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 15

B. Design and Installation Considerations . . . . . . . . . . . . . . 16

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 16

D. Inspect Appliance and Components . . . . . . . . . . . . . . . . . 16

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 17

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 18

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

D. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 20

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 21

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 30

B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 30

C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 31

D. Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 32

9 Appliance Preparation

A. Appliance Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

B. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 34

C. Active Convection Technology . . . . . . . . . . . . . . . . . . . . . 35

10 Installing Vent Pipe (DVP Pipe)

A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 36

B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 37

C. Secure The Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . 37

D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 38

E. Install Decorative Ceiling Components . . . . . . . . . . . . . . 38

F. Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . . 39

G. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 39

H. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 40

I. Heat Shield Requirements for Horizontal Termination . . . 40

J. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 40

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 42

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

B. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 43

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 43

D. Optional LED Lighting Circuit . . . . . . . . . . . . . . . . . . . . . . 45

E. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 45

F. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 45

G. Active Convection Blower Replacement . . . . . . . . . . . . . 46

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

3

13 Finishing

A. Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

B. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 48

C. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 50

D. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

E. Mesh Fronts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 55

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 55

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

E. Rock Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55



F. Porcelain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55



G. Granite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55



H. Sheet Metal Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . 55



I. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

J. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

K. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

15 Troubleshooting

A. IntelliFire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 57

16 Reference Materials



A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 59

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 61

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66



D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78



 = Contains updated information.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/124

B. Limited Lifetime Warranty

g

y

y p

p

y

y

y

y

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo­nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

Warranty Period HHT Manufactured Appliances and Venting

Parts Labor Gas Wood Pellet

EPA

Wood

Coal Electric Venting

Components Covered

All parts and material except as

1 Year

XXXXXXX

covered by Conditions,

Exclusions, and Limitations

listed

Igniters, electronic components,

and

lass

-installed blowers

2 years

XXX

XXXXX Factor

X Molded refractor

3 years

ears 1 year X X Castings and baffles

5

7 years 3 years X X X

10

ears

Limited

Lifetime

1 year X Burners, logs and refractory

3 yearsXXXXX Firebox and heat exchanger

XFire

HHT chimne

ots and burnpots

Manifold tubes,

and termination

anels

90 Days

4021-645C 12-29-10 Page 1 of 2

XXXXXXX

See conditions, exclusions, and limitations on next page.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

All replacement parts

ond warranty period

be

5

B. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

 7KLVZDUUDQW\RQO\FRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGWKURXJKDQ++7DXWKRUL]HGGHDOHURUGLVWULEXWRU$OLVWRI

++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQWKH++7EUDQGHGZHEVLWHV
 7KLVZDUUDQW\LVRQO\YDOLGZKLOHWKH++7DSSOLDQFHUHPDLQVDWWKHVLWHRIRULJLQDOLQVWDOODWLRQ
 &RQWDFW\RXULQVWDOOLQJGHDOHUIRUZDUUDQW\VHUYLFH,IWKHLQVWDOOLQJGHDOHULVXQDEOHWRSURYLGHQHFHVVDU\SDUWVFRQWDFW

WKHQHDUHVW++7DXWKRUL]HGGHDOHURUVXSSOLHU$GGLWLRQDOVHUYLFHIHHVPD\DSSO\LI\RXDUHVHHNLQJZDUUDQW\VHUYLFH

IURPDGHDOHURWKHUWKDQWKHGHDOHUIURPZKRP\RXRULJLQDOO\SXUFKDVHGWKHSURGXFW
 &KHFNZLWK\RXUGHDOHULQDGYDQFHIRUDQ\FRVWVWR\RXZKHQDUUDQJLQJDZDUUDQW\FDOO7UDYHODQGVKLSSLQJFKDUJHV

IRUSDUWVDUHQRWFRYHUHGE\WKLVZDUUDQW\

WARRANTY EXCLUSIONS:

7KLVZDUUDQW\GRHVQRWFRYHUWKHIROORZLQJ
 &KDQJHVLQVXUIDFHILQLVKHVDVDUHVXOWRIQRUPDOXVH$VDKHDWLQJDSSOLDQFHVRPHFKDQJHVLQFRORURILQWHULRUDQG

H[WHULRUVXUIDFHILQLVKHVPD\RFFXU7KLVLVQRWDIODZDQGLVQRWFRYHUHGXQGHUZDUUDQW\

 'DPDJHWRSULQWHGSODWHGRUHQDPHOHGVXUIDFHVFDXVHGE\ILQJHUSULQWVDFFLGHQWVPLVXVHVFUDWFKHVPHOWHGLWHPV

RURWKHUH[WHUQDOVRXUFHVDQGUHVLGXHVOHIWRQWKHSODWHGVXUIDFHVIURPWKHXVHRIDEUDVLYHFOHDQHUVRUSROLVKHV

 5HSDLURUUHSODFHPHQWRISDUWVWKDWDUHVXEMHFWWRQRUPDOZHDUDQGWHDUGXULQJWKHZDUUDQW\SHULRG7KHVHSDUWV

LQFOXGHSDLQWZRRGSHOOHWDQGFRDOJDVNHWVILUHEULFNVJUDWHVIODPHJXLGHVOLJKWEXOEVEDWWHULHVDQGWKHGLVFRORU-

DWLRQRIJODVV

 0LQRUH[SDQVLRQFRQWUDFWLRQRUPRYHPHQWRIFHUWDLQSDUWVFDXVLQJQRLVH7KHVHFRQGLWLRQVDUHQRUPDODQGFRP-

SODLQWVUHODWHGWRWKLVQRLVHDUHQRWFRYHUHGE\WKLVZDUUDQW\

 'DPDJHVUHVXOWLQJIURPIDLOXUHWRLQVWDOORSHUDWHRUPDLQWDLQWKHDSSOLDQFHLQDFFRUGDQFHZLWKWKHLQVWDOODWLRQ

LQVWUXFWLRQVRSHUDWLQJLQVWUXFWLRQVDQGOLVWLQJDJHQWLGHQWLILFDWLRQODEHOIXUQLVKHGZLWKWKHDSSOLDQFHIDLOXUHWR

LQVWDOOWKHDSSOLDQFHLQDFFRUGDQFHZLWKORFDOEXLOGLQJFRGHVVKLSSLQJRULPSURSHUKDQGOLQJLPSURSHURSHUD-

WLRQDEXVHPLVXVHFRQWLQXHGRSHUDWLRQZLWKGDPDJHGFRUURGHGRUIDLOHGFRPSRQHQWVDFFLGHQWRULPSURSHUO\
LQFRUUHFWO\SHUIRUPHGUHSDLUVHQYLURQPHQWDOFRQGLWLRQVLQDGHTXDWHYHQWLODWLRQQHJDWLYHSUHVVXUHRUGUDIWLQJ
FDXVHGE\WLJKWO\VHDOHGFRQVWUXFWLRQVLQVXIILFLHQWPDNHXSDLUVXSSO\RUKDQGOLQJGHYLFHVVXFKDVH[KDXVWIDQVRU
IRUFHGDLUIXUQDFHVRURWKHUVXFKFDXVHVXVHRIIXHOVRWKHUWKDQWKRVHVSHFLILHGLQWKHRSHUDWLQJLQVWUXFWLRQV
LQVWDOODWLRQRUXVHRIFRPSRQHQWVQRWVXSSOLHGZLWKWKHDSSOLDQFHRUDQ\RWKHUFRPSRQHQWVQRWH[SUHVVO\DXWKRUL]HG
DQGDSSURYHGE\++7PRGLILFDWLRQRIWKHDSSOLDQFHQRWH[SUHVVO\DXWKRUL]HGDQGDSSURYHGE\++7LQZULWLQJ

DQGRULQWHUUXSWLRQVRUIOXFWXDWLRQVRIHOHFWULFDOSRZHUVXSSO\WRWKHDSSOLDQFH
 1RQ++7YHQWLQJFRPSRQHQWVKHDUWKFRPSRQHQWVRURWKHUDFFHVVRULHVXVHGLQFRQMXQFWLRQZLWKWKHDSSOLDQFH
 $Q\SDUWRIDSUHH[LVWLQJILUHSODFHV\VWHPLQZKLFKDQLQVHUWRUDGHFRUDWLYHJDVDSSOLDQFHLVLQVWDOOHG

 ++7¶VREOLJDWLRQXQGHUWKLVZDUUDQW\GRHVQRWH[WHQGWRWKHDSSOLDQFH¶VFDSDELOLW\WRKHDWWKHGHVLUHGVSDFH,QIRUPD-

WLRQLVSURYLGHGWRDVVLVWWKHFRQVXPHUDQGWKHGHDOHULQVHOHFWLQJWKHSURSHUDSSOLDQFHIRUWKHDSSOLFDWLRQ&RQVLGHU-

DWLRQPXVWEHJLYHQWRDSSOLDQFHORFDWLRQDQGFRQILJXUDWLRQHQYLURQPHQWDOFRQGLWLRQVLQVXODWLRQDQGDLUWLJKWQHVVRI

WKHVWUXFWXUH

This warranty is void if:

 7KHDSSOLDQFHKDVEHHQRYHUILUHGRURSHUDWHGLQDWPRVSKHUHVFRQWDPLQDWHGE\FKORULQHIOXRULQHRURWKHUGDPDJLQJ

FKHPLFDOV2YHUILULQJFDQEHLGHQWLILHGE\EXWQRWOLPLWHGWRZDUSHGSODWHVRUWXEHVUXVWFRORUHGFDVWLURQEXEEOLQJ

FUDFNLQJDQGGLVFRORUDWLRQRIVWHHORUHQDPHOILQLVKHV
 7KHDSSOLDQFHLVVXEMHFWHGWRSURORQJHGSHULRGVRIGDPSQHVVRUFRQGHQVDWLRQ
 7KHUHLVDQ\GDPDJHWRWKHDSSOLDQFHRURWKHUFRPSRQHQWVGXHWRZDWHURUZHDWKHUGDPDJHZKLFKLVWKHUHVXOWRIEXW

QRWOLPLWHGWRLPSURSHUFKLPQH\RUYHQWLQJLQVWDOODWLRQ

LIMITATIONS OF LIABILITY:

 7KHRZQHU¶VH[FOXVLYHUHPHG\DQG++7¶VVROHREOLJDWLRQXQGHUWKLVZDUUDQW\XQGHUDQ\RWKHUZDUUDQW\H[SUHVVRU

LPSOLHGRULQFRQWUDFWWRUWRURWKHUZLVHVKDOOEHOLPLWHGWRUHSODFHPHQWUHSDLURUUHIXQGDVVSHFLILHGDERYH,QQR

HYHQWZLOO++7EHOLDEOHIRUDQ\LQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVFDXVHGE\GHIHFWVLQWKHDSSOLDQFH6RPHVWDWHV

GRQRWDOORZH[FOXVLRQVRUOLPLWDWLRQRILQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVVRWKHVHOLPLWDWLRQVPD\QRWDSSO\WR\RX

7KLVZDUUDQW\JLYHV\RXVSHFLILFULJKWV\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURPVWDWHWRVWDWH(;&(3772

7+((;7(173529,'('%</$:++70$.(612(;35(66:$55$17,(627+(57+$17+(:$55$17<

63(&,),('+(5(,17+('85$7,212)$1<,03/,(':$55$17<,6/,0,7('72'85$7,212)7+(

(;35(66(':$55$17<63(&,),('$%29(

4021-645C 12-29-10 Page 2 of 2

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/126

1

1

Listing and Code Approvals

A. Appliance Certifi cation

MODEL: RED40, RED40ST
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Vented Gas Fireplace Heater
STANDARD: ANSI Z21.88b-2008 CSA 2.33a-2008

Vented Gas Fireplace Heaters

This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burn­ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.

NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.

NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.

This appliance is tested and approved as either supplemen­tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.

B. Glass Specifi cations

This appliance is equipped with 5 mm ceramic glass. Re­place glass only with 5 mm ceramic glass. Please contact
your dealer for replacement glass.

C. BTU Specifi cations

(U.S. or Canada)

RED40

RED40ST

(NG)

RED40

RED40ST

(LP)

Models

(2000-4500 FT)

(2000-4500 FT)

US

(0-2000 FT)

CANADA

US

(0-2000 FT)

CANADA

Maximum

Input BTU/h

34,000 24,000 #34

29,500 22,000 #36

34,000 25,000 #50

31,500 23,000 #51

Minimum

Input

BTU/h

Orifi ce

Size

(DMS)

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.

• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.

Check with your local gas utility to determine proper
orifi ce size.

E. Non-Combustible Materials Specifi cation

Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be

considered non-combustible materials.

F. Combustible Materials Specifi cation

Materials made of or surfaced with wood, compressed pa­per, plant fi bers, plastics, or other material that can ignite
and burn, whether fl ame proofed or not, or plastered or
unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA

70-latest edition or the Canadian Electric Code CSA
C22.1.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

7

Note: The following requirements reference various
Massachuset ts and national codes not contain ed in this
document.

H. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above fi nished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfi ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fi tter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the fl oor
level where the gas equipment is to be installed. In addi­tion, the installing plumber or gas fi tter shall observe that
a battery operated or hard wired carbon monoxide detec­tor with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualifi ed licensed professionals for the installation of
hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fu­eled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
fl oor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that dur­ing said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.

Inspection

The state or local gas inspector of the side wall horizon­tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob­serves carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.

MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not pro­vide the parts for venting the fl ue gases, but identifi es
“special venting systems”, the following requirements
shall be satisfi ed by the manufacturer:

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accor­dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certifi ed.

Signage

A metal or plastic identifi cation plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fu­eled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB­STRUCTIONS”.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/128

• The referenced “special venting system” instructions

shall be included with the appliance or equipment in­stallation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that sys­tem shall include a parts list and detailed installation
instructions.

A copy of all installation instructions for all Product Ap­proved side wall horizontally vented gas fueled equip­ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.

See Gas Connection section for additional Common­wealth of Massachusetts requirements.

2

2

Operating Instructions

User Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during
operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as
fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other
fl ammable materials.

• Keep clothing, furniture, draperies and other fl ammable
materials away.

This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.

WARNING! Choking Hazard! Keep rock media out of
reach of children.

• Install a switch lock or a wall/remote control with child
protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot fi replace, whether
operating or cooling down.

• Teach children to NEVER touch the fi replace.

• Consider not using the fi replace when children will be
present.

Contact your dealer for more information, or visit: www.
hpba.org/safety-information.

T o prevent unintended operation when not using your fi re-
place for an extended period of time (summer months,
vacations, trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Unplug 3 volt adapter plug.

B. Your Fireplace

WARNING! DO NOT operate fi replace before read-
ing and understanding operating instructions. Failure

to operate fi replace according to operating instructions
could cause fi re or injury.

If you expect that small children or vulnerable adults may
come into contact with this fi replace, the following precau-
tions are recommended:

• Install a physical barrier such as:

- A decorative fi rescreen.

- Adjustable safety gate.

DECORATIVE DOORS

SECTION 2.D.

CLEAR SPACE

3 FT. IN FRONT

OF FIREPLACE

C. Clear Space

WARNING! DO NOT place combustible objects in front
of the fi replace. High temperatures may start a fi re. See
Figure 2.1.

A void placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.

FIXED GLASS ASSEMBLY

SECTION 14.H.

Figure 2.1 General Operating Parts/Clear Space.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

CLEAR SPACE

SECTION 2.C.

9

D. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fi replace to overheat.

This appliance has been supplied with an integral
barrier to prevent direct contact with the fi xed glass
panel. DO NOT operate the fi replace with the barrier
removed.

Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.

For more information refer to the instructions supplied with
your decorative door or front.

E. Fixed Glass Assembly

See Section 14.H.

G. Before Lighting Fireplace

Before operating this fi replace for the fi rst time, have a
qualifi ed service technician:

• Verify all shipping materials have been removed from
inside and/or underneath the fi rebox.

• Review proper placement of media, refractory kits and/or
other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT op­erate fi replace with fi xed glass assembly removed.

F. Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed
to operate your fi replace:

For safety:

• Install a switch lock or a wall/remote control with child
protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1210

H. Lighting Instructions (IPI)

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fi re or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an

intermittent pilot ignition (IPI) device
which automatically lights the burn­er. DO NOT try to light the burner by
hand.

B. BEFORE LIGHTING, smell all around

the appliance area for gas. Be sure to
smell next to the fl oor because some
gas is heavier than air and will settle
on the fl oor.

WHA T TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do
not use any phone in your building.

WARNING:

DO NOT CONNECT LINE VOLT­AGE (110/120 VAC OR 220/240
V AC) TO THE CONTROL VALVE.

Improper installation, adjustment, al­teration, service or maintenance can
cause injury or property damage. Re­fer to the owner’s information manual
provided with this appliance.

This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.

If not installed, operated, and main­tained in accordance with the manufac­turer’s instructions, this product could
expose you to substances in fuel or
fuel combustion which are known to the
State of California to cause cancer, birth
defects, or other reproductive harm.

Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.

• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.

• If you cannot reach your gas sup­plier, call the fi re department.

C. DO NOT use this appliance if any

part has been under water. Imme­diately call a qualifi ed service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.

CAUTION:

Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso­line and other liquids having fl ammable
vapors away.

DO NOT operate the appliance with
fi xed glass assembly removed, cracked
or broken. Replacement of the fi xed
glass assembly should be done by a
licensed or qualifi ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.

Also Certifi ed for Installation in a
Bedroom or a Bedsitting Room.

For assistance or additional informa­tion, consult a qualifi ed installer, ser-
vice agency or the gas supplier.

LIGHTING

INSTRUCTIONS (IPI)

1. This appliance is equipped with an ignition

device which automatically lights the burner.

DO NOT try to light the burner by hand.

GAS

VALVE

2. Wait fi ve (5) minutes to clear out any gas.

Then smell for gas, including near the fl oor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la­bel. If you do not smell gas, go to next step.

3. To light the burner:
Equipped with wall switch: Turn ON/OFF switch

to ON.

Equipped with remote or wall control: Press

ON or FLAME button.

Equipped with thermostat: Set temperature to

desired setting.

4. If the appliance does not light after three tries,
call your service technician or gas supplier.

TO TURN OFF

GAS TO APPLIANCE

1. Equipped with wall switch: Turn ON/OFF switch

to OFF.

Equipped with remote or wall control: Press

OFF button.

Equipped with thermostat: Set temperature to

lowest setting.

2. Service technician should turn off electric
power to the control when performing service.

593-913G

Hearth & Home Technologies fi replace, please refer to www.fi replaces.com.

For additional information on operating your

Final inspection by

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

11

I. After Fireplace is Lit

Initial Break-in Procedure

• The fireplace should be run three to four hours
continuously on high.

• Turn the fi replace off and allow it to completely cool.

• Remove fi xed glass assembly. See Section 14.H.

• Clean fi xed glass assembly. See Section 3.

• Replace the fi xed glass assembly and run continuously
on high an additional 12 hours.

This cures the materials used to manufacture the fi re-
place.

NOTICE! Open windows for air circulation during fi re-
place break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

J. Frequently Asked Questions

ISSUE SOLUTIONS

Condensation on the glass

Blue fl ames

Odor from fi replace

Film on the glass

Metallic noise

Rock noise

Rocks falling through basepan

This is a result of gas combustion and temperature variations. As the fi replace warms, this conden-
sation will disappear.

This is a result of normal operation and the fl ames will begin to yellow as the fi replace is allowed to
burn for 20 to 40 minutes.

When fi rst operated, this fi replace may release an odor for the fi rst several hours. This is caused
by the curing of materials from manufacturing. Odor may also be released from fi nishing materials
and adhesives used near the fi replace. These circumstances may require additional curing related
to the installation environment.

This is a normal result of the curing process of the paint. Glass should be cleaned within 3 to 4
hours of initial burning. A non-abrasive cleaner such as gas appliance glass cleaner may be nec­essary. See your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the
sound produced by a furnace or heating duct. This noise does not affect the operation or longevity
of the fi replace.

There may be some “cracking” noise coming from the fi replace during the fi rst few heating and
cooling cycles. This noise is associated with settling rock and some minor cracking of larger
pieces of rock. This will lessen over time as the glass rock is conditioned to the heating and cool­ing temperature changes.

It is expected that a few small pieces of rock may fall through the basepan and come to rest on the
fi replace bottom. This has no affect on fi replace performance.

Wall above appliance feels hot to
the touch.

No action necessary. This appliance ships with a non-combustible material attached. Specifi ca-
tions of the attached non-combustible material are listed in Section 1.E.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1212

3

3

Maintenance and Service

Any safety screen or guard removed for servicing must be
replaced prior to operating the fi replace.

When properly maintained, your fi replace will give you
many years of trouble-free service. We recommend an­nual service by a qualifi ed service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualifi ed service
technician only. The fi replace should be inspected before
use and at least annually by a professional service person.

The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap­pointment.

More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fi replace must be
kept clean.

CAUTION! Risk of Burns! The fi replace should be turned
off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally
By: Homeowner
Tools Needed: Protective gloves, glass cleaner, drop

cloth and a stable work surface.

CAUTION! Handle fi xed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate fi xed
glass assembly and door frame by placing a drop cloth
on a fl at, stable surface.

Note: Fixed glass assembly and gasketing may have res­idue that can stain carpeting or fl oor surfaces.

• Remove door or decorative front from fi replace and set
aside on work surface.

• See Section 14.H for instructions to remove fi xed glass
assembly.

• Clean glass with a non-abrasive commercially available
cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass

cleaner (consult with your dealer)

• Refer to Section 14.H for glass removal and replacement
instructions.

• Reinstall door or decorative front.

Doors, Surrounds, Fronts

Frequency: Annually
By: Homeowner
Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair
as necessary.

• Check that louvers are not blocked.

• Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote con-

trol instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.

• Place batteries as needed in remote transmitters and
battery-powered receivers.

• Place remote control out of reach of children.

If not using your fi replace for an extended period of time
(summer months, vacations/trips, etc), to prevent unin­tended operation:

• Remove batteries from remote controls.

• Unplug 3 volt adapter plug on IPI models.

• Verify that the sensor rod does not contact the burner.

Venting

Frequency: Seasonally
By: Homeowner
Tools needed: Protective gloves and safety glasses.

• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.

• Verify termination cap clearance to subsequent construc­tion (building additions, decks, fences, or sheds). See
Section 6.

• Inspect for corrosion or separation.

• Verify weather stripping, sealing and fl ashing remains
intact.

• Inspect draft shield to verify it is not damaged or missing.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

13

B. Maintenance Tasks-Qualifi ed Service

Technician

The following tasks must be performed by a qualifi ed ser-
vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually
By: Qualifi ed Service T echnician
T ools needed: Protective gloves, drop cloth and a stable

work surface.

• Inspect gasket seal and its condition.

• Inspect fi xed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.

• Confi rm there is no damage to glass or glass frame.
Replace as necessary.

• Verify that fi xed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.

Firebox

Frequency: Annually
By: Qualifi ed Service T echnician
Tools needed: Protective gloves, sandpaper, steel wool,

cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.

• Replace fi replace if fi rebox has been perforated.

• Inspect for lifting or other fl ame problems.

• Verify air shutter setting is correct. See Section 14.J for
required air shutter setting. Verify air shutter is clear of
dust and debris.

• Inspect orifi ce for soot, dirt and corrosion. Verify orifi ce
size is correct. See Service Parts List for proper orifi ce
sizing.

• Verify manifold and inlet pressures. Adjust regulator as
required.

• Inspect pilot fl ame pattern and strength. See Figure 3.1
for proper pilot fl ame pattern. Clean or replace orifi ce
spud as necessary.

• Inspect IPI fl ame-sensing rod for soot, corrosion and
deterioration. Polish with fi ne steel wool or replace as
required.

• Verify IPI millivolt output. Replace as necessary.

• Verify that there is not a short in fl ame sense circuit
by checking continuity between pilot hood and fl ame-
sensing rod. Replace pilot as necessary.

Control Compartment and Firebox Top

Frequency: Annually
By: Qualifi ed Service T echnician
Tools needed: Protective gloves, vacuum cleaner, dust

cloths

• V acuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.

• Remove all foreign objects.

• Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually
By: Qualifi ed Service T echnician
T ools needed: Protective gloves, vacuum cleaner, whisk

broom, fl ashlight, voltmeter, indexed drill bit set, and a
manometer.

• Verify burner is properly secured and aligned with pilot
or igniter.

• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.

• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.

Figure 3.1 IPI Pilot

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1214

4

4

A. Typical Appliance System

NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only . Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual

Getting Started

HORIZONTAL

TERMINATION CAP

(SECTION 7)

WALL PENETRATION

FRAMING

(SECTION 8B)

VERTICAL TERMINATION CAP

(SECTION 10.I)

CONVECTION

DUCTING

NON-COMBUSTIBLE ROOF FLASHING

MAINTAINS MINIMUM CLEARANCE

AROUND PIPE

(SECTION 10)

STORM COLLAR

(SECTION 10.G)

VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)

(SECTION 9.C)

Installer Guide

VENT PIPE

(SECTIONS 7&8)

CEILING FIRESTOP ON
FLOOR OF ATTIC
(SECTION 8.C)

FRAMING/HEADER
(SECTION 5)

GAS LINE
(SECTION 11)

ATTIC INSULATION SHIELD (NOT SHOWN)
MUST BE USED HERE TO KEEP INSULA­TION AWAY FROM VENT PIPE IF ATTIC IS
INSULATED. (SECTION 8.D)

FRAMING HEADED
OFF IN CEILING
JOISTS (SECTION 8.C)

WALL SWITCHES

REQUIRED ACTIVE

CONVECTION AND

CONVECTION

DUCTING

(SECTION 9.C)

Figure 4.1 Typical System

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

15

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.

Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fi re offi cials or authorities having
jurisdiction over restrictions, installation inspection and
permits.

NOTICE: The blower motor present in this appliance
will generate sound during operation. The effects of the
increased sound level can be minimized with careful
planning during installation of the system. Locating the
convection intake grill in an area remote of immediate living
space will reduce the effects of the added sound generated
during operation.

Before installing, determine the following:

• Where the appliance is to be installed.

• The vent system confi guration to be used.

• Gas supply piping.

• Electrical wiring requirements.

• Framing and fi nishing details.

• Whether optional accessories—devices such as a wall
switch or remote control—are desired.

Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualifi ed
service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following
tools and building supplies are available.

Tape measure Framing material
Pliers Non-corrosive leak check solution
Hammer Phillips screwdriver (magnetic)
Gloves Framing square
Voltmeter Electric drill and bits (1/4 in. magnetic)
Plumb line Safety glasses
Level Reciprocating saw
Manometer Flat blade screwdriver
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure

rating)
One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

• Carefully remove the appliance and components from
the packaging.

• The vent system components and decorative doors and
fronts may be shipped in separate packages.

• If packaged separately, the media and/or refractory kits
must be installed.

• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefi t.

WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.

Hearth & Home T echnologies disclaims any responsibility for ,
and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modifi cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a fi re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under

water. Call a qualifi ed service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1216

5

5

Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.

Due to high temperatures, the appliance should be locat­ed out of traffi c and away from furniture and draperies.

A

E

1 IN.

1 IN.

A

45°

B

C

ONE 90° ELBOW

TOP VENT

NOTICE: Illustrations refl ect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.

It is important to follow the framing and fi nishing instruc-
tions step by step to ensure proper placement of fi replace
in the surrounding framing/fi nishing materials. For addi-
tional information and considerations for the active con­vection technology in regards to appliance location and
framing, see Section 9.

B

ALCOVE

INSTALLATION

D

Inches 60-3/8 50 85-3/8

Millimeters 1533 1270 2168 613 476

Figure 5.1 Appliance Locations RED40

Note: Consider installation of the active con-

vection blower when determining appliance
location. See Section 9.C for more detailed
information.

TOP VENT

ONE 90° ELBOW

B

F

ABC D E F

See Section D.

Figure 5.6 & 5.7

24-1/8 18-3/4

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

17

1/2 IN.

NAILING TABS
BOTH SIDES

Note: Consider installation of the active con­vection blower when determining appliance
location. See Section 9.C for more detailed
information.

C

A

Inches 48 17-1/4 36

B

Millimeters 1218 438 914

ABC

1/2 IN.

Figure 5.2 Appliance Locations RED40ST

C

B. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should enclosed inside the chase.

NOTICE: Treatment of ceiling fi restops and wall shield
fi restops and construction of the chase may vary with the

type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.

Chases should be constructed in the manner of all out­side walls of the home to prevent cold air drafting prob­lems. The chase should not break the outside building
envelope in any manner.

Walls, ceiling, base plate and cantilever fl oor of the chase
should be insulated. Vapor and air infi ltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infi ltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling fi re-
stops should be caulked with caulk with a minimum of
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk
with a minimum of 300ºF continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being
installed on a cement surface, a layer of plywood may be
placed underneath to prevent conducting cold up into the
room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.

WARNING! Risk of Fire! Maintain specifi ed air space
clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent
accidental contact.

• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fi replace or chimney.

• Failure to maintain airspace may cause overheating and
fi re.

Figure 5.3 Nailing Tab Locations

Note: Figure 5.3, Figure 5.4, and Figure 5.5 show the fi replace

installed on the fl oor. However, this fi replace can be elevated
off the fl oor provided that the fi replace is properly supported by
framing materials and the ceiling clearances are maintained.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1218

Inches

A

F

B

J

C

D

G

MEASURE FROM TOP OF
FIREPLACE OPENING

I

E

H

MINIMUM FRAMING DIMENSIONS*

ABCDE F GHIJ

Rough

Opening

(Vent Pipe)

10 46-3/4 18-1/4 50-1/4 31 0 0 1 1 36

Rough

Opening

(Height)

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Behind

Appliance

Sides of

Appliance

Front of

Appliance

Millimeters

254 1187 464 1276 787 0 0 25 25 914

Figure 5.4. Clearances to Combustibles-RED40

A

C

D

B

MEASURE FROM TOP OF
FIREPLACE OPENING

E

F

I

G

H

ABCDE F GHI

Rough

Opening

(Vent Pipe)

Inches

Millimeters

10 46-3/4 17-1/4 50-1/4 31 0 0 1 36

254 1187 438 1276 787 0 0 25 914

Figure 5.5. Clearances to Combustibles-RED40ST

Rough

Opening

(Height)

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

MINIMUM FRAMING DIMENSIONS*

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Sides of

Appliance

Front or

Rear of

Appliance

19

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear­ances to combustibles as specifi ed. Framing or fi nishing
material closer than the minimums listed must be construct­ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).

Combustible Mantels

Note: All

measurements
in inches.

TO CEILING

18

12

11

10

9

8

7

6

7

11

10

9

8

31

25

13

12

Combustible Mantel Legs Or Wall Projections
Extending Past The Face Of The Fireplace

2 IN.
MIN.

UNLIMITED

FIREPLACE

OPENING

4 IN.

MAX.

6 IN.
MIN.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Figure 5.6 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles

Note: For non-combustible fi replace fi nish material (marble,

stone, etc) specifi cations refer to Section 13.

Non-Combustible Mantels

TO CEILING

MAX.

16

10

9

8

7

6

1/2

5

4

MEASUREMENTS FROM TOP EDGE OF THE

3

2

1

FIRESCREEN DOOR ASSEMBLY

12

6

5

4

Note: All
measurements
in inches.

31

MIN.

= ACCEPT ABLE

NON-COMBUSTIBLE

MANTEL LEG

ZONE

Figure 5.8 Mantel Leg or Wall Projections
(Acceptable on both sides of opening)

Figure 5.7 Minimum Vertical and Maximum Horizontal
Dimensions of Non-Combustibles

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1220

6

6

Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.
Maintain vent clearance to combustibles as

specifi ed.

• DO NOT pack air space with insulation or other
materials.

Failure to keep insulation or other materials away
from vent pipe may cause overheating and fi re.

HORIZONTAL

OVERHANG

2 FT.
MIN.

GAS DIRECT VENT
TERMINATION CAP

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING

X

12

ROOF PITCH

IS X/ 12

VERTICAL

WALL

6 in. (minimum) up to 20 in.

AB

152 mm/508 mm

20 in. and over 0 in. minimum

18 in. minimum

457 mm

Gas, Wood or Fuel Oil

Termination Cap

B

A *

Gas

Termination

Cap **

If using decorative cap cover(s), this distance may need to be

*

increased. Refer to the installation instructions supplied with the
decorative cap cover.

In a staggered installation with both gas and wood or fuel oil

**

terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening

Figure 6.2 Staggered Termination Caps

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

21

O

N

P

C

V

B

J

V

V

= VENT TERMINAL

X

= AIR SUPPLY INLET

B

D

V

V

V

F

B

A

G

M

V

H or i

V

X

H

V

H

E

V

V

A

= AREA WHERE TERMINAL IS NOT PERMITTED

R

Q

V

L

K

Electrical

V

Service

C

V

K

V

A = 12 inches.................clearances above grade, veranda,

porch, deck or balcony

12 inches.................clearance to window or door that may

B =

be opened, or to permanently closed

window

C = 18 inches.................clearance below unventilated soffi t

18 inches.................clearance below ventilated soffi t

30

inches .................clearance below vinyl soffits and

electrical service

D = 6 inches...................clearance to outside corner

E = 6 inches...................clearance to inside corner

F = 3 ft. (Canada) ..........not to be installed above a gas me-

ter/regulator assembly within 3 feet

horizontally from the center-line of the

regulator

G = 3 ft ...........................clearance to gas service regulator

vent outlet
H = 9 inches (U.S.A)

12 inches (Canada). clearance to non-mechanical (unpow-

ered) air supply inlet, combustion air

inlet or direct-vent termination
i = 3 ft. (U.S.A.)

6 ft. (Canada) ...........clearance to a mechanical (powered)

air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.

J = 7 ft. ......................... On public property: clearance above

paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved

driveway which is located between two single family dwellings
and serves both dwellings.

K = 6 inches................. clearance from sides of electrical

service

L = 12 inches................ clearance above electrical service

Location of the vent termination must not interfere with access to the
electrical service.

M = 18 inches ....................clearance under veranda, porch, deck,

balcony or overhang
42

inches ................vinyl or composite overhang

Permitted when veranda, porch, deck or balcony is fully open

on a minimum of 2 sides beneath the fl oor.

Figure 6.3 Minimum Clearances for Termination

Covered Alcove Applications

(Spaces open only on one side and with an overhang)

N = 6 inches ........... non-vinyl sidewalls

12 inches ......... vinyl sidewalls

O = 18 inches ......... non-vinyl soffi t and overhang

42 inches ......... vinyl soffi t and overhang

P = 8 ft.

Q

MIN

1 cap 3 feet 2 x Q
2 caps 6 feet 1 x Q
3 caps 9 feet 2/3 x Q
4 caps 12 feet 1/2 x Q

Q

= # termination caps x 3 R

MIN

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

= (2 / # termination caps) x Q

MAX

R

MAX

ACTUAL

ACTUAL

ACTUAL

ACTUAL

ACTUAL

CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffi c areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.

• Local codes or regulations may require different
clearances.

• Vent system termination is NOT permitted in screened
porches.

• Vent system termination is permitted in porch areas with
two or more sides open.

• Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.

• Vinyl protection kits are suggested for use with vinyl siding.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1222

7

7

Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home
Technologies DVP venting systems. Refer to Section
16B for vent component information.

DO NOT mix pipe, fi ttings or joining methods from differ-
ent manufacturers.

The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appli­ance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.

B. Vent Table Key

The abbreviations listed in this vent table key are used in
the vent diagrams.

Symbol Description

V
V
H

First section (closest to appliance) of vertical length

1

Second section of vertical length

2

First section (closest to appliance) of horizontal length

1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.

• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).

• Measurements are made from the appliance outer wrap,
not from the standoffs.

• Horizontal terminations are measured to the outside
mounting surface (fl ange of termination cap).

• Vertical terminations are measured to bottom of
termination cap.

• Horizontal pipe installed level with no rise.

A

B

H

Subsequent sections of horizontal length

2

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent as­pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).

Vertical

12 in.

8-1/2 in.

Horizontal

Figure 7.1

8-1/2 in.

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/12

1-1/4 in. (32 mm)

OVERLAP

Figure 7.2 Chimney Offset/Return

Effective Length

Inches Millimeters

Effective

Height/
Length

Figure 7.3 Pipe Effective Length

Pipe

DVP4 4 102

DVP6 6 152
DVP12 12 305
DVP24 24 610
DVP36 36 914
DVP48 48 1219
DVP6A 3 to 6 76 to 152

DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610

E. Vent Diagrams

General Rules:

• When penetrating a combustible wall, a wall shield
fi restop must be installed.

• When penetrating a combustible ceiling, a ceiling fi restop
must be installed.

• Horizontal runs of vent do not require vertical rise;
horizontal runs may be level.

23

Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling fi restops.

• ALWAYS maintain specifi ed clearances around venting and fi restop systems.

• Install wall shield and ceiling fi restops as specifi ed.
Failure to keep insulation or other material away from vent pipe may cause fi re.

Top Vent - Horizontal Termination

Venting with 1 elbow

WARNING

V1 Minimum H1 Maximum

1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 6 ft. 1829
3 ft. 914 mm 9 ft. 2743
4 ft. 1219 mm 12 ft. 3658
5 ft. 1524 mm 15 ft. 4572
6 ft. 1829 mm 18 ft. 5486
7 ft. 2134 mm 21 ft. 6401
8 ft. 2438 mm 24 ft. 7315

+ H1 = 63 ft. (19.2 m) Maximum

V

1

Note: 12 inches minimum vertical is
required prior to attaching any elbow
to the appliance.

H

1

Note: Use DVP Series
components only.

V

1

Figure 7.4

Heat & Glo • RED40, RED40ST • 2155-900 Rev. P • 10/1224