Heat & Glo Escape-36DV Firescreen Installation Instructions

Escape-36DV Firescreen

- Installation Instructions -

Leave this manual with party re­sponsible for use and operation.

WARNING

HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot
during operation and cool down.

• Keep children away.

• CAREFULLY SUPERVISE children in same
room as appliance.

• Alert children and adults to hazards of high
temperatures.

• Do NOT operate with protective barriers open
or removed.

• Keep clothing, furniture, draperies and other
combustibles away.

NOTICE

If the Escape-36DV has the stand-offs
noted in Figure 1, follow installation Steps
1 through 9. If the stand-offs are not
present and hearth tabs are visible (see
Figure 2) follow installation Steps 10
through 18.

Compare Figures 1 and 2.

FRONT
PANEL

FIRESCREEN SUPPORT

FIRESCREEN

(MESH NOT SHOWN)

ASH LIP

Note: Glass shown off the fi replace for clarity. Glass, panels and

ash lip must be installed properly before placing the fi rescreen on.

Figure 1

HEARTH

STAND- OFFS

GLASS

ASSEMBLY

ASSEMBLY

TABS

FRONT
PANEL

1. Remove the front panels and ash lip from the
fi replace.

2. Remove the pull-type mesh by unhooking from
the back side of the opening. This mesh is
not to be used with the fi rescreen front.

3. Locate the two fi rescreen support assemblies
that are shown in Figure 1.

4. Remove the nuts from the fi rescreen sup­ports.

5. Locate the two holes on the left and right
side of the glass frame’s base. Place the
two threaded studs on the fi rescreen support
through the two holes from underneath the
glass frame. Tighten the two nuts down on
top of the glass frame. The supports will be
angled slightly uphill.

Printed in U.S.A. • InD • Copyright 2006
Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044

FIRESCREEN

SUPPORT

Figure 2. No Stand-offs

2012-915C 5/06

6. Repeat for other side.

7. Attach the hood to the glass assembly as

shown in Figure 3.

8. Replace the ash lip and front panels. It is

easiest to put the left and right panels in
fi rst. Bring the bottoms in toward the center
and guide the tops into place while sliding
the bottom outward. Place the ash lip in
place last.

9. Slide the top tabs on the fi rescreen front

behind the top of the viewing opening. Bring
the bottom towards the glass. Lift slightly.
The two small tabs will rest into the slots
on the fi rescreen supports.

10. Remove the front panels and ash lip from

the fi replace.

11. Remove the pull-type mesh by unhooking

from the back side of the opening. This
mesh does not get used with the fi rescreen
front.

12. Remove the glass assembly from the

unit.

13. Place the fi rescreen support on top of the

metal fl oor in front of where the glass was
sitting. You may have to fl ex it into place
slightly.

HOOD

Note: The hood should be positioned

below the return bend on the glass frame.

Figure 3

Service Parts

Item Part Number

Hardware Bag 2012-915A

GLASS

ASSEMBLY

14. Attach the fi rescreen support to the metal

fl oor with the two screws included in the
kit.

15. Replace the glass assembly onto the front

of the fi replace and latch all four latches.

16. Attach the hood to the glass assembly as

shown in Figure 3.

17. Replace the ash lip and front panels. It is

easiest to put the left and right panels in
fi rst. Bring the bottoms in toward the center
and guide the tops into place while sliding
the bottom outward. Place the ash lip in
place last.

18. Slide the top tabs on the fi rescreen front

behind the top of the viewing opening. Lift
the bottom into place so it sits on top of the
support piece and bottoms out against the
tabs on each side of the support piece.