Heat & Glo CFL-18NG-B, CFL-24NG-B, ST-CFL-24NG, CFL-30NG-B, CFL-18LP-B Installation And Operation Instructions Manual

INSTALLATION AND OPERATION INSTRUCTIONS

MODEL CFL-18NG-B, CFL-24NG-B,

CFL-30NG-B, ST-CFL-24NG:

NATURAL GAS

READ THIS MANUAL BEFORE INST ALLATION AND

LEA VE IT WITH THE APPLIANCE FOR OPERATION AND MAINTENANCE.

WARNING: If the information in this
manual is not followed exactly , a fire or
explosion may result causing property
damage, personal injury or loss of life.

MODEL CFL-18LP-B, CFL-24LP-B,

CFL-30LP-B, ST -CFL-24LP:

LP GAS (PROP ANE)

- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.

- WHAT T O DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas
supplier's instructions.

• If you cannot reach your gas supplier , call

the fire department.

- Installation and service must be performed

by a qualified installer, service agency or
the gas supplier.

Copyright 2005
Heat & Glo, a brand of Hearth & Home Technologies
20802 Kensington Blvd., Lakeville, Mn 55044
Printed in U.S.A.

Underwriters Laboratories

Listed

WARNING:

Improper installation, adjustment, alter­ation, service or maintenance can cause
injury or property damage. Refer to the
owner's information manual provided with
this appliance. For assistance or addi­tional information consult a qualified in­staller , service agency or the gas supplier.

Please contact your Heat & Glo dealer with
any questions or concerns. For the number
of your nearest Heat & Glo dealer, please call
888-427-3973

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 481 1534, 5000162, 5016609, 5076254, 51 13843, 5191877, 5218953, 5263471,
5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165,
6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174,
D462436; (Canada) 1297749, 2195264, 2225408; or other U.S. and foreign patents pending.

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

1

Table of Contents

SERVICE P ARTS LIST............................................................................................................3

!

1.0 INTRODUCTION ..........................................................................................................15

2.0 ASSEMBLY .................................................................................................................15

GAS LINE CONNECTION............................................................................................ 16

3.0 OPERA TING GUIDELINES AND MAINTENANCE INSTRUCTIONS.............................17

LP (PROP ANE) INFORMA TION................................................................................... 17

SAFETY INFORMA TION ..............................................................................................18

LIGHTING INSTRUCTIONS .......................................................................................... 19

4.0 HIGH ELEV A TION INST ALLATION...............................................................................20

!

WARRANTY POLICY ............................................................................................................. 21

2

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

! = Contains updated information.

Service Parts

CFL-18-B

11

(NG , LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces

15

Beginning Manufacturing Date: 7/98
Ending Manufacturing Date: ______

13

10

9

14

8

12

2

3

16

5

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

1

Part number list on following page.

6

7

*

La liste des numéros de pièce se

*
trouve à la page suivante.

4

3

Service Parts List / Liste des pièces de rechange

CFL-18-B

IMPORT AN T: THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering,

supply serial and model numbers to ensure correct service parts. / IMPORT ANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une

ITEM /
PIÈCE

DESCRIPTION

SERIAL #

/ N° DE SÉ RIE

PART NUMBER

/ N° DE PIÈCE

1 Valve NG / Valve GN 060-500
1 Valve LP / Valve PL 060-501

Pilot Assembly NG / Module de veilleuse GN 446-512A
Pilot Assembly PL / Module de veilleuse PL 446-513A
Pilot Orifice NG / Orifice de veilleuse GN 446-505
Pilot Orifice PL / Orifice de veilleuse PL 446-517
Thermocouple / Thermocouple 446-511

Thermopile / Thermopile 060-512
2 Burner N G / Br ûl eur G N 526-326A
2 Burner LP / B r ûleur PL 526-326A
3 Burner Tube / Tube de brûleur 477-301A
4 Grate A s sembly / Grille 526-360
5 Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle 302-320A
6 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT 060-511
7 Piezo Ignitor / Allumage Piézo 291-513

8 & 9 Must order both logs / Bûches PRE 4-04

SRV481-766
SRV481-755

8 Logs 1 and 2 / Bûches 1 and 2 POST 4-04 SRV481-766
9 Logs 3 and 4 / Bûches 3 and 4 POST 4-04 SRV481-755

10 Log 5 / Bûche 5 SRV481-701

11 Log 6 / Bûche 6 SRV481-705
12 Log 7 / Bûche 7 SRV446-702
13 Log 8 / Bûche 8 SRV481-703
14 Log 9 / Bûche 9 SRV402-701
15 Log 10 / Bûche 10 SRV446-706
16 Burner Orifice NG (1.55mm) / Orifice de brûleur GN (1.55mm) 526-801
16 Burner Orifice LP (2.30mm) / Orifice de brûleur PL (2.30mm) 526-800

Single Wire Assembly (24 inch) / Module de fil 049-555A
Wire Assembly (24 feet) / Module de fil 089-550A
Pilot Tube / Tube de veilleuse 446-301

4

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

Service Parts

CFL-24-B

11

15

(NG , LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces

13

Beginning Manufacturing Date: 7/98
Ending Manufacturing Date: ______

10

14

12

8

9

2

3

4

16

5

1

Part number list on following page.

*

La liste des numéros de pièce se trouve à la page suivante.

*

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

6

7

5

Service Parts List / Liste des pièces de rechange

CFL-24-B

IMPORT AN T: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,

supply serial and model numbers to ensure correct service parts. / IMPORT ANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une
commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.

ITEM /
PIÈCE

DESCRIPTION

SERIAL #

/ N° DE SÉRIE

PART NUMBER

/ N° DE PIÈCE

1 Valve NG / Valve GN 060-500
1 Valve LP / Valve PL 060-501

Pilot Assembly NG / Module de veilleuse GN 446-512A
Pilot Assembly PL / Module de veilleuse PL 446-513A
Pilot Orifice NG / Orifice de veilleuse GN 446-505
Pilot Orifice PL / Orifice de veilleuse PL 446-517
Thermocouple / Thermocouple 446-511

Thermopile / Thermopile 060-512
2 Burner NG / Brûleur G N 526-326A
2 Bu r ner LP / Brûle ur PL 526-326A
3 Burner Tube / Tube de brûleur 477-301A
4 Gra te Asse m b ly / Gri lle 526-360
5 Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle 302-320A
6 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT 060-511
7 Piezo Ignitor / Allumage Piézo 291-513

8 & 9 Must order both logs) / Bûches PRE 4-04

SRV481-766
SRV481-755

8 Logs 1 and 2 / Bûches 1 and 2 POST 4-04 SRV481-766
9 Logs 3 and 4 / Bûches 3 and 4 POST 4-04 SRV481-755

10 Log 5 / Bûche 5 SRV526-701

11 Log 6 / Bûche 6 SRV481-705
12 Log 7 / Bûc he 7 SRV446-702
13 Log 8 / Bûc he 8 SRV481-703
14 Log 9 / Bûc he 9 SRV402-701
15 Log 10 / Bûche 10 SRV446-706
16 Burner Orifice NG (1.55mm) / Orifice de brûleur GN (1.55mm) 526-801
16 Burner Orifice LP (2.30mm) / Orifice de brûleur PL (2.30mm) 526-800

Single Wire Assembly (24 inch) / Module de fil 049-555A
Wire Assembly (24 feet) / Module de fil 089-550A
Pilot Tube / Tube de veilleuse 446-301

6

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

Service Parts

CFL-30-B

(NG , LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces

15

13

Beginning Manufacturing Date: 7/98
Ending Manufacturing Date: ______

14

16

11

8

9

10

12

8

9

2

3

4

17

5

1

6

7

Part number list on following page.

*

La liste des numéros de pièce se trouve à la page suivante.

*

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

7

Service Parts List / Liste des pièces de rechange

CFL-30-B

IMPORT AN T: THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering,

supply serial and model numbers to ensure correct service parts. / IMPORT ANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une
commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.

ITEM /

PIÈCE

DESCRIPTION

SERIAL #

/ N° DE SÉRIE

PART NUMBER

/ N° DE PIÈCE

1 Valve NG / Valve GN 060-500
1 Valve LP / Valve PL 060-501

Pilot Assembly NG / Module de veilleuse GN 446-512A
Pilot Assembly PL / Module de veilleuse PL 446-513A
Pilot Orifice NG / Orifice de veilleuse GN 446-505
Pilot Orifice PL / Orifice de veilleuse PL 446-517
Thermocouple / Thermocouple 446-511

Thermopile / Thermopile 060-512
2 Bu r ner N G / Brûleur G N 526-326A
2 Burner LP / Br ûleur PL 526-326A
3 Burner Tube / Tube de brûleur 477-301A
4 Grate As s e m b ly / Gri lle 526-360
5 Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de B alle 302-320A
6 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT 060-511
7 Piezo Ignitor / Allumage Piézo 291-513

8 & 9 Must order both logs / Bûches PRE 4-04

SRV526-766
SRV526-755

8 Logs 1 and 2 / Bûches 1 and 2 POST 4-04 SRV526-766
9 Logs 3 and 4 / Bûche 3 and 4 POST 4-04 SRV526-755

10 Log 5 / Bûche 5 SRV526-701

11 Log 6 / Bûche 6 SRV481-705
12 Log 7 / Bûche 7 SRV446-702
13 Log 8 / Bûche 8 SRV481-704
14 Log 9 / Bûche 9 SRV446-705
15 Log 10 / B ûc he 10 SRV446-706
16 Log 11 / B ûc he 11 SRV530-703
17 Burner Orifice NG (1.55mm) / Orifice de brûleur GN (1.55mm) 526-801
17 Burner Orifice LP (2.30mm) / Orifice de brûleur PL (2.30mm) 526-800

Single Wire Assembly (24 inch) / Module de fil 049-555A
Wire Assembly (24 feet) / Module de fil 089-550A
Pilot Tube / Tube de veilleuse 446-301

8

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

Service Parts

ST-CFL-24

10

(NG , LP) Exploded Parts Diagram
(GN, PL) Vue éclatée des pièces

13

15

16

Beginning Manufacturing Date: 7-98

Ending Manufacturing Date: ______

12

9

17

8

18

14

9

11

10

3

2

19

4

5

1

6

7

4

Part number list on following page.

*

La liste des numéros de pièce se trouve à la page suivante.

*

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

9

Service Parts List / Liste des pièces de rechange

ST-CFL-24

IMPORT AN T: THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering,

supply serial and model numbers to ensure correct service parts. / IMPORT ANT : L'information fournie dans cette brochure n'est
valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une
commande, veuillez fournir les numéros de série et de modèles pour un remplacement adéquat des pièces.

ITEM /
PIÈCE

DESCRIPTION

SERIAL #

/ N° DE SÉRI E

PART NUMBE R

/ N° DE PIÈCE

1 Valve NG / Valve GN 060-500
1 Valve LP / Valve PL 060-501

Pilot Assembly NG / Module de veilleuse GN 446-512A
Pilot Assembly PL / Module de veilleuse PL 446-513A
Pilot Orifice NG / Orifice de veilleuse GN 446-505
Pilot Orifice PL / Orifice de veilleuse PL 446-517
The rmocouple / Thermocouple 446-511

The rmopile / Thermopile 060-512
2 Bur ne r NG / Brûleur GN 569-701A
2 Bur ne r L P / B r ûle ur PL 569-701A
3 Burner Tube / Tube de brûleur 477-301A
4 Gra te Asse m bly / Grille 526-360
5 Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle 302-320A
6 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT060-511

7 Piezo Ignitor / Allumage Piézo 291-513
8 Logs 1 / Bûches 1 SRV569-710

9 & 10 Must order both logs / Bûches PRE 4-04

9 Logs 2 and 3 / Bûches 2 and 3 POST 4-04

SRV481-755
SRV569-711

SRV569-711
10 Logs 4 and 5 / Bûches 4 and 5 POST 4-04 SRV481-755
11 Log 6 / Bûche 6 SRV569-708
12 Log 7 / B ûc he 7 SRV569-709
13 Log 8 / B ûc he 8 SRV569-704
14 Log 9 / B ûc he 9 SRV569-706
15 Log 10 / Bûche 10 SRV569-707
16 Log 11 / Bûche 11 SRV569-702
17 Log 12 / Bûche 12 SRV569-703
18 Log 13 / Bûche 13 SRV569-705

Log Set Assembly / Jeu de bûches LOGS-STCF L
19 Burner Orifice NG (1.55mm) / Orifice de brûleur GN (1.55mm) 526-801
19 Burner Orifice LP (2.30mm) / Orifice de brûleur PL (2.30mm) 526-800

Single Wire Assembly (24 inch) / Module de fil 049-555A

Wire Assembly (24 feet) / Module de fil 089-550A

Pilot Tube / Tube de veilleuse 446-301

10

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

13 1/2

19 1/2

TOP VIEW

Gas Log Positioning

MINIMUM FIREPLACE SIZE
FRONT WIDTH : 23 1/2” (750mm)
REAR WIDTH : 19 1/2” (521mm)
DEPTH : 13 1/2” (331mm)
HEIGHT : 22” (508mm)

23 1/2

FIGURE 1. MODEL CFL-18-B

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

11

15 1/2

22

TOP VIEW

Gas Log Positioning

MINIMUM FIREPLACE SIZE
FRONT WIDTH : 27 1/2” (750mm)
REAR WIDTH : 22” (521mm)
DEPTH : 15 1/2” (331mm)

HEIGHT : 22” (508mm)

27 1/2

FIGURE 2. MODEL CFL-24-B

12

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

15 1/2

24

TOP VIEW

Gas Log Positioning

MINIMUM FIREPLACE SIZE
FRONT WIDTH : 30” (750mm)
REAR WIDTH : 24” (521mm)
DEPTH : 15 1/2” (331mm)
HEIGHT : 22” (508mm)

30

FIGURE 3. MODEL CFL-30-B

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

13

Gas Log Positioning

24

MINIMUM FIREPLACE SIZE
FRONT WIDTH : 24” (521mm)

17

TOP VIEW

REAR WIDTH : 24” (521mm)
DEPTH : 17” (331mm)
HEIGHT : 20” (508mm)

24

FIGURE 4. MODEL ST-CFL-24

14

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

1.0 INTRODUCTION

The information in this manual pertains to Models CFL­18 NG/LP-B, CFL-24 NG/LP-B, CFL-30 NG/LP-B and
ST-CFL-24NG/LP.

Gas Log Sets are Decorative Gas Appliances for Inst al­lation in a Solid-fuel Burning Fireplace. Minimum fire­place sizes for these models are shown in Figures 1, 2,
3 and 4.

WARNING: This log set must NOT be installed in

an unvented appliance.
This log set is to be installed only in a solid-fuel burn-

ing fireplace with a working flue and one constructed
of noncombustible material. The minimum permanent
vent opening provided by the fireplace chimney damper
to vent the flue products must not be less than 51
square inches (328cm2). The chimney damper MUST
be fixed in a manner to maintain the minimum perma­nent vent opening. This may be accomplished by fas­tening the damper stop clamp provided to the edge of
the damper to prevent its closing.

WARNING: OPEN THE CHIMNEY DAMPER TO

ITS FULLY OPEN POSITION WHEN BURNING THIS
GAS LOG SET.

WARNING: LOGS MUST NEVER BE BURNED

WITHOUT THE FLUE DAMPER IN THE FULL OPEN
POSITION. FAILURE TO DO SO IS DANGEROUS
TO YOUR HEALTH AND VOIDS ALL WARRANTIES.

WARNING: ALL GAS APPLIANCES PRODUCE

SOME CARBON MONOXIDE WHEN OPERATED.
CARBON MONOXIDE IS A COLORLESS, ODOR­LESS, POISONOUS GAS. ADEQUA TE PROVISIONS
MUST BE MADE TO PROVIDE COMBUSTION AIR
FOR THIS GAS LOG SET. IF OUTSIDE AIR IS NOT
INCLUDED IN THE FIREPLACE, IT MAY BE NEC­ESSARY THA T AN ADDITIONAL COMBUSTION AIR
SOURCE BE PROVIDED.

CAUTION: CHECK THE CONSTRUCTION OF

THE FIREPLACE BEFORE INSTALLING THE GAS
LOG SET. THE AREA OF THE FLUE SHOULD NOT
BE LESS THAN 1/1 1 THE AREA OF THE FIREPLACE
OPENING NON-AIRTIGHT GLASS DOORS SHOULD
BE INSTALLED ON THE FIREPLACE IF THE AREA
OF THE FLUE IS LESS THAN 1/1 1 THE AREA OF THE
FIREPLACE OPENING .

CAUTION: To minimize the possibility of spillage

and to maximize proper draft, position the log set as
close to the back of the fireplace as possible. The ST ­CFL-24 log set should be positioned in the center of
the unit.

The installation, including provisions for combustion and
ventilation air, must conform with the National Fuel Gas
Code ANSI Z223.1 (in the United States), the CAN/
CGA B-149 Installation Code (in Canada) and appli­cable local building codes.

These models can be installed in a bedroom (in the
United States) which has a total volume of unconfined
space appropriate to the particular installation. Refer
to the National Fuel Gas Code ANSI Z223.1/NFP A 54­(current edition). The Uniform Mechanical Code (cur­rent edition), and Local Building Officials for the options
allowed in obtaining an effective bedroom volume of un­confined space.

Always keep the appliance area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.

Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the unit and to replace any part of the control
system and any gas control which has been under water.

WARNING: THIS UNIT IS NOT FOR USE WITH

SOLID FUEL. SOLID FUELS SHALL NOT BE
BURNED IN A FIREPLACE WHERE A DECORA TIVE
APPLIANCE IS INSTALLED.

2.0 ASSEMBLY

CAUTION: WHEN INSTALLING THIS LOG SET IN

A FACTORY BUILT FIREPLACE, BE CERTAIN TO
CONSULT THE FIREPLACE INSTALLATION
MANUAL. ALL KNOCKOUTS IN THE FIREPLACE
THROUGH WHICH THE GAS SUPPL Y LINE IS RUN
MUST BE RESEALED WITH INSULATION AFTER
THE GAS LINE IS IN PLACE.

These models contain complete gas-burner , grate(s),
and log components needed. Use caution when han­dling logs to avoid damage. Position the gas-burner

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

assembly to the rear of the fireplace. The ST -CFL-24 log
set should be positioned in the center of the unit. Once
fully assembled, the front log will extend forward of the
burner assembly .

A. Run proper size gas line into fireplace. A 1/2 inch
(13mm) gas line, with a 3/8 inch (10mm) reduction for
hook-up, is usually sufficient for the Gas Log set; how­ever, if the run is unusually long, a larger line may be
required. Contact your local gas company or Depart­ment of Building and Safety if there are any questions.

15

B. Minimum inlet gas supply pressure for purposes of
input adjustment, shall be 7.0 inches w.c. (1.75kPa)
for natural gas and 1 1.0 inches w .c. (2.75kPa) for pro­pane (LP gas). Maximum inlet gas supply pressure
shall be 14.0 in. w.c. (3.5kPa) for both natural gas and
propane (LP gas). Manifold (outlet) pressure should
be 3.5 inches w.c. (.87kPa) for natural gas and 10.0
inches w.c. (2.5kPa) for LP gas.

C. The appliance and its individual shut off valve must
be disconnected from the gas supply piping system
during any pressure testing of the system at test pres­sures in excess of 1/2 psig (3.5kPa).

D. This appliance must be isolated from the gas sup­ply piping system by closing its individual manual shut
off valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
1/2 psig (3.5kPa).

E. NOTE: THE GAS SUPPLY LINE SHOULD BE

PURGED OF ANY TRAPPED AIR PRIOR TO THE
FIRST FIRING OF THE UNIT.

F. CAUTION: During the initial purging and sub­sequent lightings, NEVER allow the gas control
valve knob to remain depressed in the "PILOT" po­sition without pushing the red ignitor button at least
once every second.

G. A damper stop clamp with set screw is provided to
prevent full closure of the fireplace damper blade. At­tach the clamp to the edge of the damper blade with
pliers or wrenches. If the damper stop supplied does
not fit the application, use a permanent means that will
keep the damper open to a MINIMUM of 51 square
inches (328cm2). See Figure 5.

WARNING: OPEN THE CHIMNEY DAMPER TO ITS
FULL Y OPEN POSITION WHEN BURNING THIS GAS

LOG SET .
WARNING: LOGS MUST NEVER BE BURNED WITH-

OUT THE FLUE DAMPER IN THE FULL OPEN POSI­TION. FAILURE TO DO SO IS DANGEROUS TO YOUR
HEAL TH AND VOIDS ALL WARRANTIES.

H. NOTE: The Commonwealthof Massachusetts re­quires that the chimney flue damper, when used with
gas logs, shall be welded open or completely removed.

I. Your appliance control system is a millivolt type. It
consists of a pilot burner , a gas control valve/regulator,
a thermopile, a piezo ignitor, and an ON/OFF rocker
switch. See Figure 6 for control system wiring diagram.

J. NOTE: An Optional Remote Control Kit and Wall
Switch Kit , for turning the burner ON/OFF are avail­able. Detailed installation instructions are found in each
kit.

K. Test fire the unit after referring to the SAFETY IN-
FORMATION and LIGHTING INSTRUCTIONS found
in Section 3 in this manual, or on the label plate as­sembly found on the gas-burner.

L. After the gas line installation is complete, all con­nections must be tightened and checked for leaks with
a commercially-available, non-corrosive leak check
solution. Be sure to rinse off all leak check solution
following testing. Refer to Section 3, OPERATING
GUIDELINES and MAINTENANCE INSTRUCTIONS.

M. Once the gas-burner is test fired and gas supply
lines are purged, assemble the grate(s) and logs. Be
certain to follow the Log Placement Instructions shipped
with your unit. Remember to keep the Log Instructions
along with this manual for future use.

Figure 5

16

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

Figure 6

3.0 OPERATING GUIDELINES AND MAINTENANCE INSTRUCTIONS

Upon completing the gas line connection, a small amount
of air will be in the lines. When first lighting the pilot
light, it will take a few minutes for the lines to purge
themselves of this air. Once the purging is complete,
the pilot and burner will light and operate as indicated
in the instruction manual. Subsequent lighting of the
appliance will not require such purging.

WARNING:

Be sure fireplace screen or glass doors are in place
when burning fireplace logs. Unless other provisions

for combustion air are provided, the screen or
doors shall have an opening for introduction of
combustion air. THIS GAS LOG SET IS NOT DE-

SIGNED TO OPERATE WITH AIR TIGHT GLASS
DOORS. If gas odor is noticeable, turn control knob to
"OFF" position and check all connections for leaks. DO
NOT USE OPEN FLAME. Adequate combustion and

cooling air must be provided or the unit will not
function properly .

To obtain proper operation, it is imperative that the pi­lot and main burner flame characteristics are steady,
not lifting or floating.

Typically, the top 3/8 inch (10mm) of the thermopile
should be engulfed in the pilot flame (Figure 7).

Periodically remove the logs and examine the burner. If
dirty, clean with a soft brush. Also examine the area
around the burner air shutter and the pilot. Any dirt or
lint in this area should be removed. This will ensure
long life and trouble-free operation. When the appliance
is put back in service, check the burner flame patterns
with Figure 8.

The appliance and venting system should be inspected
before initial use and inspected and cleaned at least
annually by a qualified field service person.

CFL-18-B
CFL-24-B
CFL-30-B

ST-CFL24

Figure 8
LPG (PROPANE) INFORMATION

THE FOLLOWING WARNING APPLIES TO IN­STALLATIONS USING L.P. (PROPANE) GAS:

WARNING: To avoid possible injury , fire and explo-

sion, please read and follow these precautions and all
instructions on this appliance before lighting the pilot.
This appliance uses L.P. (Propane) gas which is

heavier than air and will remain at floor level if
there is a leak. Before lighting, smell at floor level
and/or use other means (such as using a commer-

cially-available, non-corrosive leak check solution on all
piping and connections, using a gas detector, etc.) to

check for gas leaks. NOTE: L.P . (Propane) gas can
become odorless and CANNOT always be detected
by smell. If you smell gas, detect a gas leak, or sus-

pect that a gas leak exists, follow these rules.

1. Get all people out of building.

2. DO NOT light matches. DO NOT turn electric
lights or switches on or off in area. DO NOT use an
electric fan to remove gas from area. DO NOT
use a telephone inside the building.

3. Shut off gas at L.P. tank outside of building.

4. T elephone gas company and fire dep artment and
ask for instructions.

Figure 7

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

Before hanging up, give your name, address and phone
number. DO NOT go back into building.

If your L.P. tank runs out of fuel, turn off gas at the
appliance. Af ter L.P . t ank is refilled, appliance must be
re-lit according to manufacturer’s instructions. If the gas
control has been exposed to WATER in any way, DO
NOT try to use it. It must be replaced. DO NOT attempt
repair on gas control or appliance.

Tampering is DANGEROUS and voids all warranties.
Any component that is found to be faulty must be re­placed with an approved component.

17

SAFETY INFORMATION

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING:

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

A. This appliance has a pilot which must be

lighted by hand. When lighting the pilot, fol­low these instructions exactly .

B. BEFORE LIGHTING smell all around the ap-

pliance area for gas. Be sure to smell next to
the floor because some gas is heavier than
air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use
any phone in your building.

• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the
fire department.

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will
not push in or turn by hand, don’t try to repair
it, call a qualified service technician. Force or
attempted repair may result in a fire or explo­sion.

D. Do not use this appliance if any part has been

under water. Immediately call a qualified ser­vice technician to inspect the appliance and to
replace any part of the control system and any
gas control which has been under water.

18

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

LIGHTING INSTRUCTIONS

LIGHTING INSTRUCTIONS

1. "STOP!" Read the safety information on previous
page.

2. Open the control access cover (logs #3 and 4 in
CFL models) or (logs #4 and 5 in ST-CFL
model), refer to your Log Placement Instructions.

3. Turn the valve control knob to the "OFF"
position. To do this, you must turn the knob
clockwise to the "Pilot" position, and
then press in and continue turning
clockwise to the "OFF" position.

GAS CONTROL VALVE

NOTE: Knob cannot be turned from "PILOT" to

"OFF" unless knob is pushed in slightly. Do not
force.

4. WAIT FIVE (5) MINUTES TO CLEAR OUT
ANY GAS. Then smell for gas, including near
the floor. If you then smell gas, STOP! Follow
"B" in the safety information previous page. If
you don't smell gas, go to the next step.

5. The pilot should not require accessing for
lighting purposes. The pilot is located at the
end of the burner.

THERMOPILE PILOT BURNER

6. To put the control in the "Pilot" position, turn the
control knob counter-clockwise
"Pilot" position.

7. To light the pilot depress the control knob and then
depress the red piezo button until it makes a
clicking sound. It may be necessary to repeat this
step. If the pilot does not light after 10 seconds, go
back to step 3. The control knob should be held
down for a MINUTE after pilot ignition.

• If the control knob does not pop out when
released, STOP-shut off the gas supply to
the fireplace control valve, and IMMEDI-
ATELY call your service technician or gas
supplier.

• If the pilot will not stay lit after two tries, turn
the control knob to the "OFF" position and
call your service technician or gas supplier.

8. After the pilot has been lit, the burner can be turned
on by turning the knob counter-clockwise

to the "ON" position. Flip the ON/OFF
switch to the "ON" position. (This is located to the
right on the burner leg and behind the control
access cover.)

9. Close control access cover.

to the

TO TURN OFF GAS APPLIANCE

1. Turn ON/OFF switch to "OFF".

2. Open the control access cover.

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

3. Turn the valve control knob clockwise
to the "Pilot" position, then depress knob and
continue turning to "OFF" position.

4. Close control access cover.

19

4.0 HIGH ELEVATION INSTALLATION

U.L. Listed gas appliances are tested and approved
without requiring changes for elevations from 0 to 2,000
feet in the U. S. A. and in Canada.

When installing this appliance at an elevation above
2,000 feet, it may be necessary to decrease the input
rating by changing the existing burner orifice to a smaller
size. Input rate should be reduced by 4% for each 1000
feet above a 2000 foot elevation in the U.S.A. or 10%

for elevations between 2000 and 4500 feet in Canada.
If the heating value of the gas has been reduced, these
rules do not apply. To identify the proper orifice size,
check with the local gas utility.

If installing this appliance at an elevation above 4,500
feet (in Canada), check with local authorities.

20

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

!

LIMITED LIFETIME WARRANTY

HEAT & GLO GAS APPLIANCE PRODUCTS

BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington
Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEA T & GLO Gas Appliance (the “Product”)
will be free from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEA T & GLO
will replace or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs
incurred in replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.

EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in
material or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and
limitations described below.

CONDITIONS, EXCLUSIONS AND LIMIT ATIONS:

1. This warranty applies to the original owner only and is nontransferable.

2. This warranty applies only to Products installed in the United States of America or Canada.

3. This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all
obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable
under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an
expedient and cost-effective manner, HEA T & GLO may discharge all obligations under this warranty by refunding the purchase price of
the Product. IN NO EVENT SHALL HEA T & GLO BE LIABLE FOR ANY INCIDENT AL OR CONSEQUENTIAL DAMAGES CAUSED BY
DEFECTS IN THE PRODUCT.

4. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited
Lifetime Warranty are not covered by this warranty , except as provided for under the Basic One-Y ear W arranty .

5. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this
warranty unless expressly authorized and approved by HEAT & GLO in writing.

6. Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure,
air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.

7. This warranty will be void if:
a) The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s

Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.

b) Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and

approved by HEAT & GLO in writing.
c) Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.
d) The Product is damaged due to shipping, improper handling, accident, abuse or misuse.
e) Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.
f)

Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.

EXCEPT TO THE EXTENT PROVIDED BY LA W , HEA T & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE W ARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED T O THE DURATION OF THE WARRANTY SPEC­IFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential
damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from State to State.

If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or
components, contact the nearest authorized HEAT & GLO dealer or supplier.

NOTES TO CUSTOMER:

1. In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual
servicing by an authorized HEA T & GLO dealer .

2. Please complete this information and retain this warranty in a safe place for future reference: Installation Date:______
Model #:_________________ Serial #:______________ Installing Contractor:_________________________

3. HEA T & GLO reserves the right to make changes at any time, without notice, in design, material, specifications
and prices of the Product. HEA T & GLO also reserves the right to discontinue styles and products.

© 2005 Hearth & Home Technologies Inc.

Heat & Glo • CFL-18/24/30-B, ST-CFL-24 • 526-900 Rev. F • 7/05

060-981D 3/05

21