Heat & Glo CDM Doors Installation Instructions
CDM Doors Installation Instructions
CAUTION: GLASS IS HOT DURING OPERA TION
!
AND COOL DOWN. These doors are supplied
from the factory locked shut for child safety . T o avoid
burns or clothing ignition, the doors must remain
closed if children will be present during the operation and cool down of the fireplace.
These instructions are to be left
with a person responsible for the
ARCHED
DOORS
use and operation of the fireplace.
Box should contain the following:
1 - Arched frame
1 - Left side arched door
1 - Right side arched door
1 - Bag with instructions and 2 handles with
mounting screws
2 - Black mounting bolts (Infinity model only)
WARNING: ALWAYS BE SURE
!
FIREPLACE IS OFF AND COOL
BEFORE HANDLING DOORS.
Figure 1
The latches may be inverted to make the doors
operable per the following instructions. This
may be done only upon request of a person
responsible for the use and operation of the
fireplace. The doors can be returned to the
locked position following the same procedures.
DOOR
FRAME
HINGE
BLOCKS
HANDLES
1. Remove any existing door from fireplace.
2. Remove packaging from cabinet style doors and frame.
3. Hang arched door frame on fireplace. Proceed to Step 4.
Infinity Model Only: Hang arched door frame on fire-
place by inserting top tabs into the top of the fireplace
front just above the glass frame. Push the door in at the
bottom and attach with the two black bolts into the receivers on the glass frame. The glass frame can be adjusted side to side slightly if the door isn’t centered.
4. Hang arched cabinet style doors on door frame by setting top and bottom door hinge blocks over pins in frame
hinge blocks (see Figure 1).
NOTE: The latch height and the gap between the doors
may be adjusted, if necessary .
5. The door gap should be approximately 1/16” – 1/8” and
consistent from the door top to bottom. If not, remove
the cabinet doors from the door frame and the door frame
from the fireplace.
PINS
SLOTS
Figure 2. Door gap adjustment (back side of frame)
6. Loosen the screw on the backside of the door
frame and slide the hinge block pin(s) within the
slot(s) to adjust gap (see Figure 2).
Printed in U.S.A. Copyright 2004
Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
2003-901E 3/04
7. Reinstall door frame and doors. Adjust height
of latches by loosening two nuts on either
side of latch and raising or lowering latch as
needed (see Figure 3).
NOTE: DO NOT use abrasive polish to clean the brass
doors. This may damage the clear lacquer finish and
cause the brass to discolor.
8. Install handles with screws and washers pro-
vided. Screws must be inserted from back
side of door and screwed into threaded holes
in handles.
9. If top of door does not contact frame when
latched, the set of the door can be adjusted
by holding top of door against frame and pulling bottom of door out approximately one
inch. NOTE: For 8000 Series, see DF8TRC/BT A-8TRC instructions (included) to
install lower louver .
10. To make doors operable, remove ball latch
brackets using a 3/8” socket wrench and reattach (see Figure 3). Doors may need to
NUTS
LATCH
be adjusted by either sliding the bracket up
or down and/or adjusting the hinges on the
back of the doors.
Figure 3 Latch height adjustment (back side of door)
Service Parts List
UNIT
CDM-6-BK 289-320 289-330 289-445 N/A N/A CDM-LATCH
CDM-6-PB 289-131A 289-130A 289-444 289-250A 289-251A 345-800A
CDM-6-PT 2003-017 2003-018 289-876 289-447A 289-449A 345-800A
CDM-8-BK 289-323 289-333 289-445 N/A N/A CDM-LATCH
CDM-8-PB 289-324 289-334 289-444 N/A N/A CDM-LATCH
CDM-8-PT 289-145A 289-146A 289-876 289-879 289-880 345-800A
CDM-G50-PB 289-327 289-337 289-444 N/A N/A CDM-LATCH
CDM-G50-PT 289-328 289-338 289-445 N/A N/A CDM-LATCH
CDM-INFINITY-BK 289-320 289-330 289-445 N/A N/A CDM-LATCH
CDM-INFINITY-PB 289-321 289-331 289-444 N/A N/A CDM-LATCH
CDM-INFINITY-PT 2003-017 2003-018 289-445 289-447A 289-449A 345-800A
CDM-OLY-BK 780-204A 780-205A 289-445 289-447A 289-449A 345-800A
CDM-OLY-PT 780-214A 780-215A 289-445 289-447A 289-449A 345-800A
CDM-OLY-PB 780-200A 780-201A 289-875 289-881 289-882 CDM-LATCH
LEFT DOOR
ASSEMBLY
RIGHT DOOR
ASSEMBLY
DOOR HINGE
LEFT HINGE
RECEIVER
ASSEMBLY
RIGHT HINGE
RECEIVER
ASSEMBLY
BALL LATCH
ASSEMBLY
UNIT HANDLE BAG ASSEMBLY TOP LOUVER BOTTOM LOUVER
CDM-6-BK 289-500 289-900A 289-244A 459-244A
CDM-6-PB 060-024A 289-906A 459-244A 459-244A
CDM-6-PT 289-500 289-905A 289-244A 459-244A
CDM-8-BK 289-500 289-902A 582-139A 582-148A
CDM-8-PB 289-501 289-903A 582-139A 582-148A
CDM-8-PT 289-500 289-905A N/A 582-148A
CDM-G50-PB 289-501 289-901A 570-244A 570-242A
CDM-G50-PT 289-500 289-900A 570-244A 570-242A
CDM-INFINITY-BK 289-500 289-900A N/A N/A
CDM-INFINITY-PB 289-501 289-901A N/A N/A
CDM-INFINITY-PT 289-500 203-901A N/A N/A
CDM-OLY-BK 289-500 780-902A 582-239A 570-242A
CDM-OLY-PT 289-500 780-902A 582-239A 570-242A
CDM-OLY-PB 289-501 289-901A 582-239A 570-242A
Loading...