Heat & Glo 8000TVC User Manual

Heat-N-Glo

Model:

8000TVC

WARNING IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- What to do if you smell gas

 Do not try to light any appliance.

 Do not touch any electrical switch.

Installers Guide

Underwriters

Laboratories Listed

READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS INSTALLERS GUIDE MUST BE LEFT WITH THE APPLIANCE FOR FUTURE REFERENCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, SERVICE AGENCY, OR THE GAS SUPPLIER.

 Do not use any phone in your building.

 Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's instructions.

 If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322; 4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia) 543790;586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

Please contact your Heat-N-Glo dealer with any questions or concerns. For the number of your nearest Heat-N-Glo dealer, please call 612-985-6000.

258-900C 10/99

SAFETY AND WARNING INFORMATION

READ and UNDERSTAND all instructions carefully before starting the installation.

FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty.

Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the

Owners Guide.

DO NOT USE this appliance if any part has been under water. Immediately CALL a

qualified service technician to inspect the unit and to replace any part of the control system and any gas control which has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a qualified service person. The appliance and venting system should be INSPECTED before initial use and at least

annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is IMPERATIVE that the units control compartment, burners, and circulating air passageways BE KEPT CLEAN to provide for adequate combustion and ventilation air.

Always KEEP the appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the

appliance CLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should be LOCATED out of traffic areas

and away from furniture and draperies. Clothing or flammable material SHOULD NOT BE PLACED on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature

and should STAY AWAY to avoid burns or clothing ignition. Young children should be CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units MUST use one of the vent systems described in the Installing the

Fireplace section of the Installers Guide. NO OTHER vent systems or components MAY BE USED.

This gas fireplace and vent assembly MUST be vented directly to the outside and

MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas appliance MUST USE a separate vent system. Common vent systems are PROHIBITED.

INSPECT the external vent cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly MUST be in place and sealed, and the trim door assembly

MUST be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service person. DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied

by the gas fireplace manufacturer. NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door assembly. DO NOT ATTEMPT to

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

service technician perform an appliance check-up at the beginning of each heating season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

Safety and Warning Information.......................... i

Section 1: Approvals and Codes ...................... 1

Approval Listings and Codes ..................................... 1

Appliance Certification ............................................... 1

Installation Codes ...................................................... 1

High Altitude Installations ........................................... 1

Section 2: Getting Started .................................. 2

Introducing the Heat-N-Glo Gas Fireplaces ............... 2

Pre-installation Preparation ....................................... 2

Section 3: Installing the Fireplace ..................... 4

Step 1 Locating the Fireplace ................................... 4

Step 2 Framing the Fireplace ................................... 5

Step 3 Negative Pressure Make-up Air ..................... 5

Step 4 Installing the Vent System ............................. 7

A. Vent System Approvals ............................. 7

B. System Components................................ 7

C. Bedroom Installation in Canada ................ 9

D. Vent Termination ....................................... 9

Step 5 Positioning, Leveling, and

Securing the Fireplace ................................ 10

Step 6 The Gas Control Systems .......................... 10

Step 7 The Gas Supply Line ................................... 12

Step 8 Gas Pressure Requirements ...................... 13

Step 9 Wiring the Fireplace .................................... 14

Step 10 Finishing ...................................................... 17

Step 11 I

Step 12 Before Lighting the Fireplace ...................... 20

Step 13 Lighting the Fireplace .................................. 20

nstalling Trim, Logs, and Ember Materia

Installing the Trim ........................................ 18

Positioning the Logs .................................... 18

Placing the Ember Material ......................... 18

l ..... 18

Section 4: Maintaining and Servicing

Your Fireplace ................................. 21

Section 5: Replacement Parts

and Accessories ..............................23

Replacement Parts ................................................. 23

Accessories ............................................................ 28

u = Contains updated information.

i i

Approval Listings and Codes

MODEL LABORATORY TYPE STANDARD

Appliance Certification

The Heat-N-Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories.

CERTIFICATION

Approvals and Codes

8000TVC Underwriters Vented ANSI

Laboratories Gas Fireplace

Installation Codes

The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you are in compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGAB149 Installation Codes (in Canada). The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes with the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the CSA C22.1 Canadian Electric Code (in Canada).

These models (natural gas and propane) can be installed in a bedroom (in the United States) which has a total volume of unconfined space appropriate to the particular installation. Refer to the National Fuel Gas Code ANSI Z223.1/NFPA54 (current edition). The Uniform Mechanical Code - (current edition), and local Building Officials for the options allowed in obtaining an effective bedroom volume of unconfined space.

These models (natural gas and propane) can be installed in a bedroom (in Canada) if a thermostat (Model WH-STAT) is installed with the unit. Consult local code authorities. Detailed installation instructions for Model WH-STAT are included with the kit.

Z21.50CGA2.2

High Altitude Installations

U.L. Listed fireplaces are tested and approved for elevations from 0 to 2,000 feet in the U.S.A. and are tested and approved for elevations from 0 to 4,500 feet in Canada.

When installing this fireplace at an elevation above 2,000 feet (in the United States), it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input should be reduced four percent (4%) for each 1,000 feet above sea level, unless the heating value of the gas has been reduced, in which case this general rule will not apply. To identify the proper orifice size, check with the local gas utility.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for your location.

Introducing the Heat-N-Glo Gas Fireplaces

Pre-installation Preparation

Heat-N-Glo B-type vent gas fireplaces are designed to operate with all exhaust gases expelled to the outside of the building.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems.

Gas fireplace diagrams, including the dimensions, are shown in this section.

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do

not install any unit with damaged, incomplete, or substitute parts.

The vent system components and trim doors are shipped in separate packages. Log installation instructions are provided in the manual bag assembly shipped with unit. Read all of the instructions

before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owners warranty and may present a fire hazard.

Getting Started

The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo disclaims any responsibility for, the following actions:

 Installation of any damaged fireplace or vent system

component.

 Modification of the fireplace or vent system.

 Installation other than as instructed by Heat-N-Glo.

 Improper positioning of the gas logs or the glass

door.

 Installation and/or use of any component part not

manufactured and approved by Heat-N-Glo, not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, its necessary to determine:

 Where the unit is to be installed.

 The vent system configuration to be used.

 Gas supply piping.

 Electrical wiring.

 Framing and finishing details.

 Whether optional accessoriesdevices such as a fan, wall switch, or remote

controlare desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

Figure 1. Diagram of 8000TVC

Step 1 Locating the Fireplace

The diagram below shows space and clearance requirements for locating a fireplace within a room.

Installing the Fireplace

MODELS A B C D E

8000TVC 49 22 39 1/2 56 79

Figure 2. Fireplace Dimensions, Locations, and

Space Requirements

Clearance Requirements

The top, back, and sides of the fireplace are defined by stand-offs.

Minimum Clearances from the Fireplace to

Combustible Materials

Glass Back of Sides of Top of

Front Floor Fireplace Fireplace Fireplace Ceiling

36 inches 0 1/2 inch 1/2 inch 31/2 inches (89mm) 31 inches

(914 mm) (13 mm) (13 mm) (787 mm)

The minimum clearance to a perpendicular wall extending past the face of the fireplace is one inch (25mm).

The minimum clearance from the top face of the fireplace to combustible finishing materials such as drywall, is one inch (25mm).

The back of the fireplace may be recessed 21 1/2 inches (546mm) into combustible construction.

Minimum Clearances from the B-Type Vent Pipe to Combustible Materials is 1 inch (25mm) all around the pipe.

Step 2 Framing the Fireplace

Fireplace framing can be built before or after the fireplace is set in place. Framing should be positioned to accommodate wall coverings and fireplace facing material. The diagram below shows framing reference dimensions.

CAUTION

MEASURE FIREPLACE DIMENSIONS, AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING CONSTRUCTION BEGINS.

WARNING:

To ensure proper clearances the front framing header must be installed on its narrow edge and to the front of the frame.

Framing should be constructed of 2 X 4 lumber or heavier.

Models A B C

8000TVC 49 40

1/2 22

NOTE: DIMENSIONS SHOWN IN INCHES

Figure 3. Framing Dimensions

Step 3 Negative Pressure Make-up Air

Negative Pressure warning: When negative pressure is present, an atmospherically vented fireplace (with a draft hood) may not function properly and it may down draft. In the case of a gas appliance, spillage of the combustion gases may occur. This may create a dangerous carbon monoxide situation in the house.

The causes of negative pressure to a house can include the following:

 Stack effect in the building.

 Exhaust only appliances (mechanically and

atmospherically vented).

 Inadequate make-up air (which is increasingly

more prevalent in new construction).

It is recommended that all natural venting non-air tight gas fireplaces have outside air connected to them. It is also recommended that the building be mechanically or passively balanced to allow

atmospherically vented appliances, such as top

+ 17 hidden pages

Heat & Glo 8000TVC User Manual

Installers Guide

Table of Contents