HearthStone 8050 Owner's Manual & Installation Manual
Owner’s Manual &
Ne pas vous
servir des téléphones se trouvant dans le
Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
Stove Model #8050
HearthStone
Quality Home Heating Products, Inc.
Installation Guide for
Tribute DV
(8050) GAS-FIRED
DIRECT-VENT
HEATER
READ THIS OWNER’S MANUAL - Operate and
maintain this gas heater according to this instruction manual.
WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property damage,
personal injury or loss of life.
Do not store or use gasoline or other flammable
vapors and liquids near this or any other gas
appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch electrical switches; do not use
the phone in your building.
• Immediately call your gas supplier from a
neighbors phone. Follow your gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
A qualified installer, service agency or gas supplier
must perform installation and service. In the
Commonwealth of Massachusetts, all installation
of gas lines and gas fitting shall only be done by a
licensed gas fitter or licensed plumber.
AVERTISSEMENT: Assurez-vous de bien suivre
les instructions donné dans cette notice pour
réduire au minimum le risque d’incendie ou pour
éviter tout dommage matéeriel, toute blessure ou
la mort.
Ne pas entresposer ni utiliser d’essence ni d’autre
vaperurs ou liquides inflammables dans le
voisinage de cet apprareil ou de tout autre
appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucun interrupteur.
batiment où vous vous trouvez.
•
du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de
gaz, appelez le service des incendies.
L’installation et service doit être exécuté par un
installateur qualifié, agence de service ou le
fournisseur de gaz.
317 Stafford Ave nue,
Morrisville, Vermont 05661-8695
E-Mail: Info@hearthstonestoves.com
PN 6400-40423 Rev. A 4/26/06
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
2
INFORMATION SHEET
Use this page to record all relevant information concerning the purchase, installation, and maintenance
of your Tribute DV Gas-Fired Direct-Vent heater. This information will facilitate servicing, purchase
of replacement parts, and warranty claims (if necessary). Keep your original receipt in a safe place as
proof of purchase.
Serial Number:
Fuel type (check one) Natural Gas Liquid Propane
Sold by:
Phone: Date of Purchase:
Installed by:
Phone: Date of Installation:
Gas Supplier:
Phone:
Read this Owner’s Manual before installing or operating the Tribute DV. Retain this manual for future
reference.
SERVICE RECORD
Important - Verify proper operation after servicing!
Date Who Performed Work Work Performed Notes:
WHAT WHEN WHAT WHEN
Firebox Cleaning............. annually Door Gasket.................... Replacement as needed
Glass Cleaning................ as needed
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
3
TABLE OF CONTENTS
INTRODUCTION.................................................................3
SPECIFICATIONS: ........................................................ 5
OWNER’S INFORMATION.................................................6
INSTALLER’S INFORMATION...........................................7
ITEMS REQUIRED FOR INSTALLATION...........................7
UNPACKING AND INSPECTION.........................................7
CLEARANCE TO COMBUSTIBLES .....................................8
V ENTING INFORMATION................................................ 10
ELECTRICAL CONNECTIONS ..........................................14
G AS SUPPLY & CONNECTIONS..................................... 17
LOG PLACEMENTERROR! BOOKMARK NOT DEFINED.
INITIAL ADJUSTMENTS...................................................21
ROUTINE MAINTENANCE AND CARE...........................24
PARTS LISTS....................................................................27
LIMITED WARR ANTIES..........................................32
INTRODUCTION
Congratulations on your purchase of
HearthStone’s Tribute DV Gas-Fired Direct
Vent heater. The Tribute DV incorporates
the latest in balanced vent gas technology,
which will provide you with clean, efficient
heat for years to come. Combustion air
comes directly from the outside of your
home to the sealed firebox system,
eliminating the potential for annoying back
drafts or other problems associated with
home depressurization.
The Tribute DV will provide you with years
of practical and convenient service.
However, as with any gas appliance, the unit
must be properly and safely installed and
maintained by qualified service personnel to
ensure safe and trouble-free operation. It
includes the new TEK Firelog technology,
which is an amazing blend of realistic
flames and glowing embers with incredible
heating characteristics.
READ THIS OWNER’S MANUAL
Operate and maintain this gas heater
according to the instructions in this manual.
For your safety, and years of trouble free
operation, read this manual in its entirety.
By following a few simple safety
precautions and by performing minimal
maintenance, the unit will remain appealing
while providing years of quality
performance.
WARNING!
A qualified service technician should do
the installation, and repair. A qualified
service technician must inspect the
appliance before use, and at least
annually. More frequent cleaning may be
required due to excessive lint from
carpeting, bedding material, pets, etc. It is
imperative that the control
compartments, burners, and circulating
air passages of the appliance are kept
clean and free of obstructions. (S’assurer
que le brûleur et le compartiment des
commandes sont propres. Voir les
instructions d’installation et d’utilisation
qui accompagnent l’appareil.)
WARNING: Do not operate this appliance
with the glass, or any panel removed,
cracked, or broken. Do not subject the door
to abuse, such as striking or slamming shut.
Replacement of the glass panel should be
done by a licensed or qualified service
person.
NEVER BURN PAPER, WOOD OR OTHER
MATERIALS
This gas heater is designed to burn natural
gas or liquid propane (LP). Never burn any
fuel not intended for use with this unit.
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
4
HOT SURFACES
Certain exposed surfaces of the Tribute DV
will reach high temperatures during normal
operation. Clearances to combustibles must
be maintained, as specified in the
“Clearances To Combustibles” section of
this manual.
Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the heater and to
replace any part of the control system and gas
control that has been under water. (Ne se
servir de cet appareil s’il a été plongé dans
l’eau, complètement ou en partie. Appeler un
technicien qualifié pour inspecter l’appareil et
remplacer toute partie du système de contrôle
et toute commande qui ont été plongés dans
l’eau.)
WARNING
This gas appliance must not be connected to
a chimney flue serving a separate solid-fuel
burning appliance. NEVER VENT THE GAS
HEATER TO OTHER ROOMS OR BUILDINGS.
Masonry Conversions Kits are an acceptable
venting option.
Due to high temperatures the appliance
should be located out of traffic and away
from furniture, draperies, clothing and
flammable materials. Children and
adults should be alerted to the hazards of
high surface temperatures and should
stay away to avoid burns to skin or
clothing ignition. Young children should
be carefully supervised when in the same
room as the appliance. Clothing or other
flammable material should not be placed
on or near the appliance. (Surveiller les
enfants. Garder les vêtements, les meubles,
l’essence ou autres liquides à vapeur
inflammables loin de l’appareil.)
FIRE HAZARD
Do not store or use gasoline or other
flammable vapors or liquids in the vicinity
of this appliance. The Tribute DV should be
located out of traffic and away from
furniture, draperies, clothing, and flammable
material.
Any shield, door, or safety screen
component removed for servicing will be
replaced prior to operating the unit.
Certified for use by:
Board of State Examiners of Plumbers and
Gasfitters
100 Cambridge Street, Room 1511
Boston, Massachusetts 02202
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
5
SPECIFICATIONS:
LISTED AS: Gas-Fired Direct-Vent Fireplace Heater
Model: Tribute DV Direct-Vent Gas Fireplace Heater (8050)
Testing Agency: Intertek Testing Services, Inc.
Tested to: ANSI Z21.88-B 2003, CSA 2.33-M02, CAN/CSA 2.17-M91
Certified for Canada, CSA P.4.1
Approved for Mobile Home Installation
Figure 1 Tribute DV Dimensions
FUEL TYPE:
INPUT RATING (Btu/hr) 0-2000 ft
ORIFICE SIZE (DMS) 0-2000 ft
MANIFOLD PRESSURE - LO SETTING (in. W.c./kpa)
MANIFOLD PRESSURE - HI SETTING (in. W.c./kpa)
INLET PRESSURE - LO (in.w.c./kpa)
MINIMUMINPUT RATING (btu/hr)
MAXIMUMOUTPUT (btu/hr) 0-2000 ft
NG LP
18,000 17,500
48 56
1.2/0.30 3.3/0.82
3.5/1.15 10.0/2.48
5.0/1.24 10.0/2.48
10,600 10,400
13,300 13,200
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
6
OWNER’S INFORMATION
The installation must conform with local
codes or, in the absences of local codes, the
current National Fuel Gas Code, ANSI Z223.1
(NFPA 54) or CAN/CSA B149 Installation
Code. (Installer l’appareil selon les codes ou
règlements locaux, ou, en l’absence de tels
règlements, selon les Codes d’installation
CAN/CSA-B149.)
DAILY OPERATION
The Tribute DV is easily operated by the
homeowner once installed and adjusted by
qualified service personnel. The unit can be
controlled via the wall-mounted thermostat
during the heating season. Set the thermostat
to the desired room temperature and the unit
will cycle on and off as required. By
adjusting the variable output control located
on the gas control valve, the rate of heat
output can be varied to meet the heating
requirements of the season. Choosing a low
flame setting will result in longer burn
cycles at a reduced output, while choosing a
high flame setting will result in a shorter,
hotter burn cycle. Through trial and error,
the homeowner can select the optimum
flame size for their setting and application.
During the summer non-heating season,
switch the wall thermostat to “OFF”, and
turn off the pilot. This will improve the
overall efficiency of the unit as the heat
from the pilot is wasted. When putting the
unit back into service, follow the lighting
instructions described on page 21.
When the unit is first lit, especially when
cool, it is normal to experience some
condensation on the inside of the window
glass. This condensation will burn off within
the first few minutes of operation. If
continuous condensation on the window
glass or dripping water from any part of the
unit or venting system (chimney) is noted,
immediately discontinue operation of the
unit and contact qualified service personnel.
Clean the area around, under, and behind the
unit on a regular basis to prevent the
accumulation of dust and lint.
The Tribute DV requires minimal routine
maintenance and care. It should always be
cool and off when being cleaned, or
serviced. Once a year, the unit, and venting
system should be inspected by qualified
service personnel to insure that they are
clean, free of obstruction, safe, and in good
working order. If service or maintenance is
required, qualified service personnel should
perform it.
SERVICE CAUTION
If you believe your Tribute DV is not, in any
way, performing properly, immediately
discontinue operation until the unit has been
inspected and approved by qualified service
personnel. Prior to servicing the unit, turn
the valve control knob clockwise to “OFF”.
The unit should be cool prior to servicing
and cleaning. Use of any components not
supplied by HearthStone on the stove voids
all warranties. Do not substitute
components.
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
7
INSTALLER’S INFORMATION
CODES
Adhere to all local codes or, in their
absence, the latest edition of THE
NATIONAL FUEL GAS CODE ANSI
Z223.1 (NFPA 54) or CAN/CSA B149
Installation Code that can be obtained from:
AMERICAN NATIONAL STANDARDS
INSTITUTE, INC.
1430 BROADWAY
NEW YORK, NY 10018
OR
NATIONAL FIRE PROTECTION
ASSOCIATION, INC.
BATTERY MARCH PARK
QUINCY, MA 02269
A manufactured home (mobile) OEM
installation must conform with the
Manufactured Home Construction and
Safety Standard, Title 24 CFR, Part 3280
(U.S.) or Standard for Manufactured Home
Installation, ANSI/NCBCS A225.1 or
Standard for Gas Equipped Recreational
Vehicles and mobile Housing, CSA
Z240.4.CAN/SCA Z240 MH (Canada).
(Installer l’appareil selon les codes ou
règlements locaux, ou, en l’absence de tels
règlements, selon les Codes d’installation
CAN/CSA-B149.)
ITEMS REQUIRED FOR INSTALLATION
* External regulator (for propane/L.P.G. only)
* Piping which complies with local codes
* Pipe sealant approved for use with
propane/L.P.G. (resistant to sulfur compounds)
* Manual shutoff valve
* Sediment trap (see page 17)
* Tee joint
* Pipe wrench
* Phillips head screwdriver
* 7/16-inch wrench
* Other parts as required by local code
*Safety Glasses
*Gloves
PACKING LIST
1-Tribute DV Gas-Fired Heater
1-TEK Burner
5-Decorative TEK Firelogs
1-Owner’s Manual
1-Thermostat
1-40’ Thermostat wire
1-Warranty Validation Form
Note: Vent kits and components are supplied
separately. Failure to use the venting
components specified by HearthStone
QHHP, Inc. will void your warranty and
could risk a fire.
UNPACKING AND INSPECTION
Unpack and Inspect for Damage
The Tribute DV is packaged by the
manufacturer to withstand shipment without
damage. However, damage can still occur
during transit; so take care to inspect for
damage when unpacking and installing the
unit. If any damage, or missing parts are
detected, immediately contact your dealer.
Do not install, or put into service, a
damaged or incomplete heater.
Inspect the Tribute DV for visible or
concealed damage. The unit should appear
to be square and true. The sheet metal parts
should be smooth and free of bends and
dents. The enameled cast iron should be free
of chips or cracks. If visible or concealed
damage is found or suspected, contact your
dealer for instructions.
With the accessory box removed and set
aside, take care not to mar or chip the
enameled legs, if applicable. Have someone
help lift the stove out of the shipping box
and set it into place.
The TEK Burner and TEK Firelogs supplied
with the Tribute DV are contained in the
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
8
accessory box. Always use great care when
handling the decorative fire logs, as they are
fragile and subject to damage and breakage
if handled roughly. If a broken log is
encountered, contact your dealer for
replacement logs. Otherwise, set the logs
aside until called for during the installation.
INSTALLING THE TRIBUTE DV
HEARTH REQUIREMENT/FLOOR
PROTECTION
The Tribute DV may be placed on a
noncombustible surface or wood floor.
Installations must meet local codes.
CLEARANCE TO COMBUSTIBLES
Due to high surface temperatures, the unit
should be located out of traffic and away
from furniture and draperies. Clothing and
other flammable material should not be
placed on or near the heater. When
positioning the unit always maintain
adequate clearances around air openings into
the combustion chamber and allow for
adequate ventilation. Minimum clearances
to combustibles must be maintained as
shown in the illustrations of the Clearances
To Combustibles section.
Caution: These clearances represent
minimum distances in all cases, which,
through testing in an independent
laboratory to ANSI and CSA standards,
will prevent fire or spontaneous
combustion. We do not control the
combustible materials exposed to heat by
this product; therefore, an assessment
must be made by the installer to prevent
consequential damage of walls and
flooring.
Minimum Alcove clearances
Clearances to Combustibles
Unit top to side wall 2"
Unit top to rear wall 2"
Unit top to corner wall 2"
Unit top to corner wall 2"
Unit top to ceiling 9"
Figure 2 Clearance to combustibles
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
9
Acceptable Direct-Vent TERMINATION Cap locations.
Figure 3 Termination clearances
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
10
VENTING INFORMATION
VENT CONNECTION
1. The Tribute DV Direct Vent is
approved for installation only with
the vent connecting components
listed; Simpson Dura-Vent Direct
Vent GS, AmeriVent Direct, Selkirk
Direct Temp™ or Secure Vent
systems.
2. Install the vent system according to
the manufacturer’s instructions.
RESTRICTION PLATE
There is a vent restriction plate that adjusts
the flow rate of exhaust gases. This insures
proper flames and efficiency for the wide
variety of vent configurations. Controlling
the draft also changes the aesthetics of the
flame. The restriction plate consists of a
rotating shutter behind the starter section of
pipe and an adjustment plate with an index
hole used to hold the shutter in a fixed
position. The restriction plate has unlimited
settings. Depending on the vent
configuration, you may be required to adjust
the restriction plate position. For straight
out the back installations no adjustment
to the restrictor is necessary.
ADJUSTMENT TO RESTRICTION
PLATE
Make sure the unit is cool before touching
any part of the firebox. To adjust your
restrictor for maximum flame appearance,
loosen the Phillips head screw, found on the
upper rear right side of the stove. Spin the
indicator tab into the desired position.
Rotating counterclockwise closes the
exhaust gasses, while rotating clockwise
opens the exhaust gases. Once the desired
restriction is reached, tighten the
screw.(Refer to figure 4) There are
unlimited positions for the restriction plate,
one (1) being the lowest and three (3) being
the highest. (Refer to Venting
Configuration – Figure 5 for recommended
restriction plate positions)
NOTE: These positions are based on lab
results and can have some variance.
HearthStone Quality Home Heating Products Inc Tribute DV Model #8050
11
Figure 4 RestrVenting configuration
Loading...