Hearth & Home GFK10 Fan Kit Installation Instructions Manual
Hearth & Home Technologies • GFK10 Fan Kit • 4016-136 • Rev F • 12/17
1
Description Part Number Qty
Fan 1
Electrical Cord 1
Fan Shield 4049-238 1
Air Deector 4058-193 1
Control Module 4021-708 1
Fastener Pack 4016-048 1
Foam Tape 4021-655 2
Magnetic Tape 4021-654 2
Jumper Wire (blue) 1
tm
Models:
GFK10 Fan Kit
Installation
Instructions
Note: You may not need all parts included with this kit.
Table 1 Contents of Carton
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could
result in a safety hazard and will void the warranty.
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA 70-
latest edition or the Canadian Electric Code CSA C22.1
WARNING! Risk of Shock or Explosion! DO NOT wire IPI
controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear
protective gloves and safety glasses during installation.
Sheet metal edges are sharp.
Check Contents of Shipping Carton
Compare contents of carton in Table 1 with the actual parts
received. If any parts are missing or damaged, contact your
dealer before starting installation. Do not install a damaged
fan kit.
The GFK10 Fan Kit has been designed to circulate room air through the appliance to enhance heat output. The fan kit operates on 120VAC, 60 Hz power. This is available through a receptacle in the factory-installed junction box. The junction box
is located in the controls compartment of the appliance.
A control module is provided with the fan kit which automatically turns the fan on and o at preset times and is equipped wth
a variable speed control to provide a quiet forced air ow at the desired speeds.
Check with your local building code agency before you begin installation to ensure compliance with local codes, including
the need for permits and follow-up inspections. If you encounter any problems regarding code approvals, or if you need
clarication of any of the instructions contained here, contact your Hearth & Home Technologies Inc. dealer. For the dealer
nearest you, please visit www.hearthnhome.com.
Installation Precautions
The GFK10 Fan Kit is tested and safe when installed in accordance with this installation manual. It is your responsibility to read all instructions before starting installation and to
follow these instructions carefully during installation to as-
sure maximum benet from, and safe operation of, the fan.
►
Hearth & Home Technologies • GFK10 Fan Kit • 4016-136 • Rev F • 12/17
2
Figure 3
Figure 2
Magnetic
Tape
Foam
Figure 4
Secure with 4 screws
Figure 6
Figure 1
1. Fan Assembly
• Bend hand brakes of fan bracket as shown in Figure 1.
• Attach fan bracket by hooking hand brakes into open end
of fan as shown in Figure 2. Crimp down tight with pliers
so tabs do not interfere with rotor blades.
• Secure bracket to fan with two screws as shown in
Figure 3.
• Cut foam tape into two equal pieces.
• Apply magnetic tape and foam to fan bracket as shown
in Figure 4.
• Secure the air deector with four screws as shown in
Figure 6.
• Attach power supply cord to terminals of fan motor. Attach
ground wire to fan body with screw.
Figure 5
Note: The next two steps apply only if installing in the
Aveo:
• Locate air deector and hand brake ends as shown in
Figure 5.
The following steps apply to all installations:
Loading...