Hearth and Home Technologies 6000GLX-IPILP-R, 6000GLX-IPI-S, 6000GLX-IPI-R, 6000GLX-IPILP-S User Manual

Download

Page 1

Models: 6000GLX-IPI-S 6000GLX-IPI-R 6000GLX-IPILP-S 6000GLX-IPILP-R

Owner’ s Manual

Installation and Operation

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

WARNING: If the information in these instructions is not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury, or death.

• DO NOT store or use gasoline or other ﬂ am- mable vapors and liquids in the vicinity of this or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call

the ﬁ re department.

• Installation and service must be performed by a qualiﬁ ed installer, service agency , or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

• Read, understand and follow these instructions for safe installation and operation.

DO NOT

DISCARD

• Leave this manual with party responsible for use and operation.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualiﬁ ed personnel. Hearth & Home Technologies suggests NFI certiﬁ ed or factory trained professionals, or technicians supervised by an NFI certiﬁ ed professional.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 1

Page 2

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas ﬁ replace, an elegant and clean alternative to wood burning ﬁ replaces. The Heat & Glo gas ﬁ replace you have selected is designed to provide the utmost in safety, reliability, and efﬁ ciency.

As the owner of a new ﬁ replace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

Homeowner Reference Information

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas ﬁ replace will give you years of durable use and trouble-free enjoyment. Welcome to the Heat & Glo family of ﬁ replace products!

We recommend that you record the following pertinent information about your ﬁ replace.

Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on ﬁ replace: _____________________ Dealership purchased from: _______________________________ Dealer Phone: __________________________ Notes: _______________________________________________________________________________________ _____________________________________________________________________________________________

Listing Label Information/Location

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510,4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708,5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237,5947112,5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autresbrevetsamericainsetetrangers en attente).



Type of Gas

NotNot for for use use withwith solid solid fuel.fuel. ((NeNe doitdoit pas pas entre entre utilise utilise avecavec un un combustible combustible solide).solide).

Type Type ofof Gas Gas (Sorte(Sorte DeDe Gaz)Gaz)::

NNAATURALTURAL GASGAS

Gas and Electric Information

Minimum Minimum Permissible Permissible Gas Gas SupplySupplyfor for Purpose sPurposes ofof Input Input Adjustment.Adjustment. ApprovedApproved Minimum Minimum (De (De Gaz)Gaz)AcceptableAcceptable 0.00.0inin w.c.w.c. (Po.(Po.Col.Col. d’eau)d’eau) Maximum Maximum PressurePressure(Pression)(Pression) 0.00.0inin w.c.w.c. (Po.(Po.Col.Col. d’eau)d’eau) Maximum Maximum ManifoldManifoldPressurePressure (Pression)(Pression) 0.00.0 inin w.c.w.c. (Po.(Po.Col.Col.d’eau)d’eau) Minimum Minimum ManifoldManifold PressurePressure(Pression)(Pression) 0.00.0 inin w.c.w.c. (Po.(Po.Col.Col. d’eau)d’eau) Total Total ElectricalElectrical Requirements: Requirements: 000Vac, 000Vac, 00Hz.,00Hz.,lesslessthanthan0000 AmperesAmperes

ALTITUDE:ALTITUDE: 0-0000 0-0000 FT.FT. 0000-0000FT.0000-0000FT. MAX.MAX.INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000 MIN.MIN. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000 ORIFICE ORIFICE SIZE:SIZE: #XXXXX#XXXXX #XXXXX#XXXXX

The model information regarding your speciﬁ c ﬁ replace can be found on the rating plate usually located in the control area of the ﬁ replace.

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

ThisThisappliance appliance mustmust bebeinstalled installed inin accordanceaccordance withwith local local codes,codes, ifif any;any; ifif not,not, follow follow ANSIANSIZ223.1Z223.1 ininthe the USA USA ororCAN/CGA CAN/CGA B149 B149 installation installation codes.codes.(Installer (Installer l’appareill’appareilselon selon leslescodes codes ouou reglementsreglements

locauxlocaux ou,ou, enen l’absencel’absence dede telstels reglements, reglements, selon selon les les codescodes d’installationd’installation CAN/CGA-B149.)CAN/CGA-B149.)

ANSIANSIZ21XX-XXXXZ21XX-XXXX · · CSA CSA 2.XX-MXX2.XX-MXX · · UL307BUL307B

ININCANADACANADA

Model:Model:

(Modele):(Modele):

SerialSerial

(Serie):(Serie):

XXXXXXXXXXXXXXXX

MADEMADE ININ USAUSA

Model Number

Serial Number

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/082

Page 3

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certiﬁ cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Glass Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

C. BTU Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7

E. Non-Combustible Materials Speciﬁ cation. . . . . . . . . . . . . . 7

F. Combustible Materials Speciﬁ cation . . . . . . . . . . . . . . . . . 7

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

H. Requirements for the Commonwealth of Massachusetts . . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10

F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

G. Remote Controls, Wall Controls and Wall Switches . . . . . 10

H. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10

I. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11

J. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

K. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks-Qualiﬁ ed Service Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components . . . . . . . . . . . . . . . . . 17

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 18

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 19

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

D. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 20

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 21

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 33

B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 33

C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 34

D. Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 35

E. Installing the Optional Heat-Zone-Gas Kit . . . . . . . . . . . . 35

9 Appliance Preparation

A. Choosing the Top or Rear Vent . . . . . . . . . . . . . . . . . . . . 36

B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

C. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 37

D. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 37

10 Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . . 38

B. Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 39

C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 39

D. Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . 40

E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 40

F. Install Decorative Ceiling Components (SLP only) . . . . . . 41

G. Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . . 42

H. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 42

I. Install RF4-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

J. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 44

K. Install Decorative Wall Components (SLP only) . . . . . . . . 44

L. Heat Shield Requirements for Horizontal Termination . . . 44 M. Install Horizontal Termination Cap (DVP and SLP Pipe) . 45

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 46

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

B. Intelliﬁ re Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 47

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 47

D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 48

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 49

F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 49

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 3

Page 4

13 Finishing

A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 50

B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

C. Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 52

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 52

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

E. Install the Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

F. Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

G. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 54

H. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

I. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

J. Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . . 57

K. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

15 Troubleshooting

A. Intelliﬁ re Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 58

16 Reference Materials

A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 60

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 61

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

 = Contains updated information.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/084

Page 5

B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY

Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.

Warranty Period HHT Manufactured Appliances and Venting Parts Labor Gas Wood Pellet

1 Year XXXXXX

EPA

Wood

Electric Venting

Components Covered

All Parts and Material Except as

covered by Conditions, Exclusion,

and Limitations listed

2 years

3 years X Firepots

5 years 3 years X X Castings & Bafﬂ es

7 years 3 years X X X

10 years 1 year X Burners, Logs & Refractory

Limited

Lifetime

1 year X Firebox & Heat Exchanger

90 Days XXXXXX All Replacement Parts

XXXX Blowers

X Molded Refractory Panels

Igniters, Electronic Components,

and Glass

Firebox, HHT Chimney,

Termination & Heat

Exchanger

See Conditions, Exclusions, and limitations. 9-01-08

CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY

• This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation.

• The maximum amount recoverable under this warranty is limited to the purchase price of the product.

• In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.

• Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home is not covered under this warranty.

Page 1 of 2 4021-645A 09-01-08

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 5

Page 6

B. Limited Lifetime Warranty (continued)

• This limited warranty does not extend to or include surface ﬁ nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, ﬁ rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, bafﬂ es, ﬁ repots, doors, or ﬁ rebox area are not covered by this warranty.

• Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this noise are not covered by this warranty.

• HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identiﬁ cation label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those speciﬁ ed in the operating instructions; (6) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; and/or (7) modiﬁ cation of the appliance not expressly authorized and approved by HHT in writing.

• This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction with the installation of this product.

• This warranty is void if the appliance has been over-ﬁ red or operated in atmospheres contaminated by chlorine, ﬂ uorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

• HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.

• Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you speciﬁ c rights; you may also have other rights, which vary from state to state.

• EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE WARRANTY SPECIFIED ABOVE.

This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all warranties currently in existence.

If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HHT dealer or supplier.

Page 2 of 2 4021-645A 09-01-08

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/086

Page 7

Listing and Code Approvals

A. Appliance Certiﬁ cation

MODELS: 6000GLX-IPI-R, 6000GLX-IPI-S, 6000GLX-IPILP-R, 6000GLX-IPILP-S

LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.88-2000•CSA2.33-M98•UL307B

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Glass Speciﬁ cations

This appliance is equipped with 5 mm ceramic glass. Replace glass only with 5 mm ceramic glass. Please contact your dealer for replacement glass.

C. BTU Speciﬁ cations

U.S. (0-2000 FT) or Canada (2000-4500 FT)

Models

6000GLX-IPI-R (NG) 6000GLX-IPI-S (NG)

6000GLX-IPILP-R 6000GLX-IPILP-S

CANADA

Maximum

Input

BTUH

40,000 18,700

36,000 16,830

36,000 16,500

32,400 14,850

Minimum

Input

BTUH

Oriﬁ ce

Size

(DMS)

53 (2)

54 (2)

68 (2)

69 (2)

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

• In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper oriﬁ ce size.

E. Non-Combustible Materials Speciﬁ cation

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763 shall be

considered non-combustible materials.

F. Combustible Materials Speciﬁ cation

Materials made of or surfaced with wood, compressed paper, plant ﬁ bers, plastics, or other material that can ignite and burn, whether ﬂ ame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA

70-latest edition or the Canadian Electric Code CSA C22.1.

• A 110-120 VAC circuit for this product must be pro-

tected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 7

Page 8

Note: The following requirements reference various Massachuset ts and national codes not contained in this document.

H. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above ﬁ nished grade in the area of the venting, in- cluding but not limited to decks and porches, the following requirements shall be satisﬁ ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas ﬁ tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the ﬂ oor level where the gas equipment is to be installed. In addition, the installing plumber or gas ﬁ tter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualiﬁ ed licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent ﬂ oor level. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the ﬂ ue gases, but identiﬁ es “special venting systems”, the following requirements shall be satisﬁ ed by the manufacturer:

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certiﬁ ed.

Signage

A metal or plastic identiﬁ cation plate shall be permanent- ly mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) in. in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/088

• The referenced “special venting system” instructions

shall be included with the appliance or equipment installation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Page 9

Operating Instructions

User Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

If you expect that small children or vulnerable adults may come into contact with this ﬁ replace, the following precau- tions are recommended:

• Install a physical barrier such as:

- A decorative ﬁ rescreen.

- Adjustable safety gate.

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot ﬁ replace, whether operating or cooling down.

• Teach children to NEVER touch the ﬁ replace.

• Consider not using the ﬁ replace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/staysafe.

T o prevent unintended operation when not using your ﬁ re- place for an extended period of time (summer months, vacations, trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Unplug 3 volt adapter plug and remove batteries on IPI models.

B. Your Fireplace

WARNING! DO NOT operate ﬁ replace before read- ing and understanding operating instructions. Failure

to operate ﬁ replace according to operating instructions could cause ﬁ re or injury.

Figure 2.1 General Operating Parts

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 9

FAN KIT

SECTION 2.C

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

CLEAR SPACE

SECTION 2.D.

FIXED GLASS ASSEMBLY

(NOT SHOWN) SECTION 14.H.

HEARTH

MANTEL

Page 10

C. Fan Kit (optional)

If desired, a fan kit may be added. Contact your dealer to order the correct fan kit.

D. Clear Space

WARNING! DO NOT place combustible objects in front of the ﬁ replace or block louvers. High temperatures may start a ﬁ re. See Figure 2.2.

A void placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects.

3 FT. IN FRONT OF FIREPLACE

CLE

AR SPACE

Figure 2.2 Clear Space

F. Fixed Glass Assembly

See Section 14.H.

G. Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed to operate your ﬁ replace:

For safety:

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

H. Before Lighting Fireplace

Before operating this ﬁ replace for the ﬁ rst time, have a qualiﬁ ed service technician:

• Verify all shipping materials have been removed from inside and/or underneath the ﬁ rebox.

• Review proper placement of logs, ember material and/or other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT operate ﬁ replace with ﬁ xed glass assembly removed.

E. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause ﬁ replace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the ﬁ replace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0810

Page 11

I. Lighting Instructions (IPI)

The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an

intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B. BEFORE LIGHTING, smell all around

the appliance area for gas. Be sure to smell next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

WHA T TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any phone in your building.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

C. DO NOT use this appliance if any

part has been under water. Immediately call a qualiﬁ ed service tech- nician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

CAUTION:

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having ﬂ ammable vapors away.

DO NOT operate the appliance with ﬁ xed glass assembly removed, cracked or broken. Replacement of the ﬁ xed glass assembly should be done by a licensed or qualiﬁ ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certiﬁ ed for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualiﬁ ed installer, ser- vice agency or the gas supplier.

LIGHTING

INSTRUCTIONS

(IPI)

1. Turn off all electric power to the appliance.

2. This appliance is equipped with an ignition

device which automatically lights the burner.

DO NOT try to light the burner by hand.

GAS

VALVE

3. Wait ﬁ ve (5) minutes to clear out any gas.

Then smell for gas, including near the ﬂ oor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

4. Turn on all electric power to the appliance.

5. To light the burner, ﬂ ip the ON/OFF switch to

the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6. If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFF

GAS TO APPLIANCE

1. Turn wall control or ON/OFF switch to “OFF”.

2. Turn off all electric power to the appliance if

service is to be performed.

593-913F

Hearth & Home Technologies ﬁ replace, please refer to www.ﬁ replaces.com.

For additional information on operating your

Final inspection by

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 11

Page 12

J. After Fireplace is Lit

Initial Break-in Procedure

• The fireplace should be run three to four hours continuously on high.

• Turn the ﬁ replace off and allow it to completely cool.

• Remove ﬁ xed glass assembly. See Section 14.H.

• Clean ﬁ xed glass assembly. See Section 3.

• Replace the ﬁ xed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the ﬁ re- place.

NOTICE! Open windows for air circulation during ﬁ re- place break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

K. Frequently Asked Questions

ISSUE SOLUTIONS

Condensation on the glass

Blue ﬂ ames

Odor from appliance

Film on the glass

Metallic noise

Is it normal to see the pilot ﬂ ame burn continually?

This is a result of gas combustion and temperature variations. As the appliance warms, this condensation will disappear.

This is a result of normal operation and the ﬂ ames will begin to yellow as the appliance is al- lowed to burn for 20 to 40 minutes.

When ﬁ rst operated, this appliance may release an odor for the ﬁ rst several hours. This is caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may also be released from ﬁ nishing materials and adhesives used around the appliance.

This is a normal result of the curing process of the paint and logs. Glass should be cleaned within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing process. A non-abrasive cleaner such as gas ﬁ replace glass cleaner may be necessary. See your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the appliance.

In an Intelliﬁ re ignition system it is normal to see the pilot ﬂ ame, but it should turn off when ON/OFF is turned off.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0812

Page 13

Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the ﬁ replace.

When properly maintained, your ﬁ replace will give you many years of trouble-free service. We recommend annual service by a qualiﬁ ed service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualiﬁ ed service technician only. The ﬁ replace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the ﬁ replace must be kept clean.

CAUTION! Risk of Burns! The ﬁ replace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally By: Homeowner Tools Needed: Protective gloves, glass cleaner, drop

cloth and a stable work surface.

CAUTION! Handle ﬁ xed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate ﬁ xed glass assembly and door frame by placing a drop cloth on a ﬂ at, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or ﬂ oor surfaces.

• Remove door or decorative front from ﬁ replace and set aside on work surface.

• See Section 14.H for instructions to remove ﬁ xed glass assembly.

• Clean glass with a non-abrasive commercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass

cleaner (consult with your dealer)

• Carefully set ﬁ xed glass assembly in place on ﬁ replace. Hold glass in place with one hand and secure glass latches with the other hand.

• Reinstall door or decorative front.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 13

Doors, Surrounds, Fronts

Frequency: Annually By: Homeowner Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair as necessary.

• Check that louvers are not blocked.

• Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally By: Homeowner Tools needed: Replacement batteries and remote con-

trol instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

• Place batteries as needed in remote transmitters and battery-powered receivers.

• Place remote control out of reach of children.

If not using your ﬁ replace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

• Remove batteries from remote controls.

• Unplug 3 volt adapter plug on IPI models.

Light Bulbs

Frequency: As needed By: Homeowner T ools needed: Protective gloves, replacement light bulbs.

• Remove the door or front from the ﬁ replace.

• There are two square boxes hanging down behind the gas valve. These are separated into two pieces.

• While wearing gloves, grasp the sides of the box and slide the front/side portion towards you.

• The front will slide free of the rest of the box.

• Remove the bulb by pulling straight out.

• Reverse the steps to replace the bulb into the box.

Page 14

Venting

Frequency: Seasonally By: Homeowner Tools needed: Protective gloves and safety glasses.

• Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

• Inspect for corrosion or separation.

• Verify weather stripping, sealing and ﬂ ashing remains intact.

• Inspect draft shield to verify it is not damaged or missing.

B. Maintenance Tasks-Qualiﬁ ed Service

Technician

The following tasks must be performed by a qualiﬁ ed ser- vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually By: Qualiﬁ ed Service Technician T ools needed: Protective gloves, drop cloth and a stable

work surface.

• Inspect gasket seal and its condition.

• Inspect ﬁ xed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

• Conﬁ rm there is no damage to glass or glass frame. Replace as necessary.

• Verify that ﬁ xed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Logs

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves.

• Inspect for damaged or missing logs. Replace as necessary . Refer to Section 14 for log placement instructions.

• Verify correct log placement and no ﬂ ame impingement causing sooting. Correct as necessary.

Firebox

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves, sandpaper, steel wool,

cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

• Replace ﬁ replace if ﬁ rebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves, vacuum cleaner, dust

cloths

• V acuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

• Remove all foreign objects.

• Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually By: Qualiﬁ ed Service Technician T ools needed: Protective gloves, vacuum cleaner, whisk

broom, ﬂ ashlight, voltmeter, indexed drill bit set, and a manometer.

• Verify burner is properly secured and aligned with pilot or igniter.

• Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

• Replace Glowing embers with new dime-size pieces. DO NOT block ports or obstruct lighting paths. Refer to Section 14 for proper ember placement.

• Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or leaking.

• Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

• Inspect for lifting or other ﬂ ame problems.

• Verify air shutter setting is correct. See Section 14 for required air shutter setting. Verify air shutter is clear of dust and debris.

• Inspect oriﬁ ce for soot, dirt and corrosion. Verify oriﬁ ce size is correct. See Service Parts List for proper oriﬁ ce sizing.

• Verify manifold and inlet pressures. Adjust regulator as required.

• Inspect pilot ﬂ ame pattern and strength. See Figure 3.1 for proper pilot ﬂ ame pattern. Clean or replace oriﬁ ce spud as necessary.

• Inspect thermocouple/thermopile or IPI ﬂ ame sensing rod for soot, corrosion and deterioration. Clean with emery cloth or replace as required.

• Verify that there is not a short in ﬂ ame sense circuit by checking continuity between pilot hood and ﬂ ame sensing rod. Replace pilot as necessary.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0814

Page 15

Figure 3.1 IPI Pilot Flame Patterns

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 15

Page 16

HORIZONTAL

TERMINATION CAP

(SECTION 10.M )

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂ ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

Getting Started

Note: Dual venting configurations ARE NOT allowed. Appliance MUST

be vented EITHER vertically OR horizontally.

VERTICAL TERMINATION CAP

(SECTION 10.J)

NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE (SECTION 10.G)

STORM COLLAR (SECTION 10.H)

Installer Guide

VENT PIPE (SECTIONS 7 and 9)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.C)

FRAMING/HEADER (SECTION 5.B)

VENT PIPE PENETRATES ROOF PREFERABLY WITHOUT AFFECTING ROOF RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY FROM VENT PIPE IF ATTIC IS INSULATED (SECTIONS 8.C AND 8.D)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.C)

WALL SWITCH

MANTEL AND MANTEL LEG (SECTION 5.D)

SURROUND

OPTIONAL

GAS LINE (SECTION 11)

Figure 4.1 Typical System

HEARTH EXTENSION

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0816

Page 17

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, ﬁ re ofﬁ cials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

• Where the appliance is to be installed.

• The vent system conﬁ guration to be used.

• Gas supply piping requirements.

• Electrical wiring requirements.

• Framing and ﬁ nishing details.

• Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualiﬁ ed service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure Framing material Pliers High temperature caulking material Hammer Phillips screwdriver Gloves Framing square Voltmeter Electric drill and bits (1/4 in.) Plumb line Safety glasses Level Reciprocating saw Manometer Flat blade screwdriver Non-corrosive leak check solution 1/2 - 3/4 in. length, #6 or #8 Self-drilling screws One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

• Carefully remove the appliance and components from the packaging.

• The vent system components and decorative doors and fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate must be installed.

• Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁ t.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home T echnologies disclaims any responsibility for , and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modiﬁ cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a ﬁ re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under

water. Call a qualiﬁ ed service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 17

Page 18

Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

1/2 IN.

TOP VENT

ONE 90º ELBOW

ALCOVE

INSTALLATION

NOTICE: Illustrations reﬂ ect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

ABCD E F G H

Inches 51 42 72 56-5/8

Millimeters 1295 1067 1829 1438 559 451 203

Figure 5.1 Appliance Locations

REAR VENT,

HORIZONTAL TERMINATION,

TWO ELBOWS

REAR VENT, NO ELBOWS

See Section D.

Mantel Projections

REAR VENT, ONE ELBOW

22 17-3/4 8

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0818

Page 19

B. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling ﬁ restops and wall shield ﬁ restops and construction of the chase may vary with the

type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever ﬂ oor of the chase should be insulated. Vapor and air inﬁ ltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air inﬁ ltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling ﬁ re- stops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temperature caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth. DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain speciﬁ ed air space clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent accidental contact.

• The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with ﬁ replace or chimney.

• Failure to maintain airspace may cause overheating and a ﬁ re.

*MINIMUM FRAMING DIMENSIONS

A B C** D E F G H I J

Rough

Opening

(Vent Pipe)

Inches 10 38-1/2 22 42 26-5/8 0 0 1/2 1/2 36

Rough

Opening

(Height)

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Behind

Appliance

Sides of

Appliance

Front of

Appliance

Millimeters 254 978 559 1067 676 0 0 13 13 915

* Adjust framing dimensions for interior sheathing (such as sheetrock)

C** Add 12 inches for rear venting with one 90º elbow.

Figure 5.2 Clearances to Combustibles

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 19

Page 20

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as speciﬁ ed. Framing or ﬁ nishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantel Legs or Wall Projections

INTERIOR WALL

Combustible Mantels

2-1/2

Note: All measurements in inches.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

TO CEILING

TOP VIEW

FIREPLACE OPENING

MANTEL LEG OR WALL PROJECTIONS

If A minimum is ____, then B maximum is_____.

Inches

2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16

Millimeters

Inches

Millimeters

62 87 113 138 164 189

12345

25 51 76 102 127

∞

Figure 5.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.)

Note: Measurement is taken from top of the

opening, NOT the top of the ﬁ replace.

Figure 5.3 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0820

Page 21

Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk. Maintain vent clearance to combustibles as

speciﬁ ed.

• DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and ﬁ re.

HORIZONTAL

OVERHANG

2 FT. MIN.

GAS DIRECT VENT TERMINATION CAP

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

ROOF PITCH

IS X/ 12

VERTICAL

WALL

6in.(minimum)upto20in.

152 mm/508 mm

20 in. and over 0 in. minimum

18 in. minimum

457 mm

Gas, Wood or Fuel Oil

Termination Cap

Gas

Termination

Cap **

If using decorative cap cover(s), this distance may need to be

increased. Refer to the installation instructions supplied with the decorative cap cover.

In a staggered installation with both gas and wood terminations, the

wood termination cap must be higher than the gas termination cap.

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening

Figure 6.2 Staggered Termination Caps



Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 21

Page 22

U.S

(3 FT.)

H or i

(See Note 2)

Measure vertical clearances from this surface.

Electrical

Service

Measure horizontal clearances from this surface.

= VENT TERMINAL

= AIR SUPPLY INLET

A = 12 inches.................clearances above grade, veranda,

(See Note 1)

porch, deck or balcony

B = 12 inches.................clearances to window or door

that may be opened, or to permanently closed window. (Glass)

C = 18 inches.................vertical clearance to unventilated

sofﬁ t or to ventilated sofﬁ t located above the terminal

30 inches .................for vinyl clad sofﬁ ts and below

electrical service

D = 9 inches...................clearance to outside corner

E = 6 inches...................clearance to inside corner

F = 3 ft. (Canada) ..........not to be installed above a gas

meter/regulator assembly within 3

feet (90 cm) horizontally from the

center-line of the regulator

G = 3 ft ...........................clearance to gas service regulator

vent outlet H = 9 inches (U.S.A.)

12 inches (Canada) clearance to non-mechanical

(See Note 2)

air supply inlet to building or the

combustion air inlet to any other

appliance i = 3 ft. (U.S.A.)

6 ft. (Canada) ...........clearance to a mechanical (pow-

(See Note 2)

** a vent shall not terminate directly above a sidewalk or paved driveway

which is located between two single family dwellings and serves both dwellings.

*** only permitted if veranda, porch, deck or balcony is fully open on a

minimum of 2 sides beneath the ﬂ oor, or meets Note 2.

Note 1: On private property where termination is less than 7 feet above a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap shield is suggested. (See vents components page)

Note 2: Termination in a covered alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions speciﬁ ed for vinyl or non-vinyl siding and sofﬁ ts. 1. There must be 3 feet minimum between termination caps. 2. All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below the termination cap. 3. All gravity air intakes within 3 feet of a termination cap must be a minimum of 1 foot below the termination cap.

Figure 6.3 Minimum Clearances for Termination

ered) air supply inlet

= AREA WHERE TERMINAL IS NOT PERMITTED

J** = 7 ft. ......................... clearance above paved

(See Note 1)

sidewalk or a paved driveway located on public property

K = 6 inches................. clearance from sides of electri-

(See Note 5)

cal service

L = 12 inches................ clearance above electrical

(See Note 5)

service

Covered Alcove Applications

M*** = 18 inches .............clearance under veranda, porch,

42 inches ......... vinyl

N = 6 inches ........... non-vinyl sidewalls

12 inches .........vinyl sidewalls

O = 18 inches ......... non-vinyl sofﬁ t and overhang

42 inches .........vinyl sofﬁ t and overhang

P = 8 ft.

1 cap 3 feet 2 x Q 2 caps 6 feet 1 x Q 3 caps 9 feet 2/3 x Q 4 caps 12 feet 1/2 x Q

= # termination caps x 3 R

MIN

Note 3: Local codes or regulations may require different

clearances. Note 4: Termination caps may be hot. Consider their proximity to

doors or other trafﬁ c areas. Note 5: Location of the vent termination must not interfere with

access to the electrical service. In the U.S and Canada: Vent system termination is NOT permitted

in screened porches. Vent system termination is permitted in porch areas with two or more

sides open. You must follow all side walls, overhang and ground clearances as stated in the instructions.

Heat & Glo assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

deck, balcony or overhang

MIN

= (2 / # termination caps) x Q

MAX

ACTUAL

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0822

Page 23

Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home T echnologies DVP or SLP venting systems. Refer to Section 16B for vent component information.

DO NOT mix pipe, ﬁ ttings or joining methods from differ- ent manufacturers.

The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe serving a separate solid fuel burning appliance.

Vertical

12 in.

8-1/2 in.

B. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol Description

First section (closest to appliance) of vertical length

Second section of vertical length

First section (closest to appliance) of horizontal length

Subsequent sections of horizontal length

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1).

Horizontal

Figure 7.1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

• Pipe measurements are shown using the effective length of pipe (see Figure 7.2).

• Horizontal terminations are measured to the outside mounting surface (ﬂ ange of termination cap) (see Figure

6.3).

• Vertical terminations are measured to bottom of termination cap.

• Horizontal pipe installed level with no rise.

Effective Length

Inches Millimeters

Effective

Height/Length

Pipe

DVP4 4 102

DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152

DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610

Figure 7.2 DVP Pipe Effective Length

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 23

Page 24

E. Vent Diagrams Top Vent - Horizontal Termination



Note: The 6000 series ﬁ replaces can adapt to SLP series vent

pipe, if desired.

When venting off the top of the unit, use a DVP-2SL adapter and a minimum 48 inch vertical section of SLP series vent pipe.

A DVP-SLP24 adapter may also be used with a 24 inch vertical section of SLP series vent pipe.

After the 48 inch vertical section, the venting table rules must be followed. The ﬁ rst 48 inch vertical section is NOT counted as part of the vertical components in the table. It is still counted as part of the overall maximum run. All venting table rules for the vent run must still be followed.

Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal

Top Vent - Horizontal Termination

One Elbow

WARNING

Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles

between ceiling ﬁ restops.

• ALW A YS maintain speciﬁ ed clearances around venting and ﬁ restop systems.

• Install wall shield and ceiling ﬁ restops as speci- ﬁ ed.

Failure to keep insulation or other material away from vent pipe may cause ﬁ re.

WARNING

Fire Risk.

• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented ﬁ replaces, a 6 inch minimum vertical vent section is required before installing ﬁ rst elbow.

Minimum H1 Maximum

Elbow only 2 ft 610 mm 1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 6 ft. 1.8 m 3 ft. 914 mm 11 ft. 3.4 m

4 ft. 1.2 m 20 ft. 6.1 m

+ H1 = 40 ft. (12.2 m) Maximum

= 20 ft. (6.1 m) Maximum

Figure 7.3

Two Elbows

Figure 7.4

INSTALLED

HORIZONTALLY

Note: For corner installations: A 6 inch (152 mm) section of straight pipe may need to be attached to the appliance before a 90º elbow, to allow the vent pipe to clear the top standoffs.

V1 Minimum H1 + H2 Maximum

Elbow only 1 ft. 305 mm

6 in. 152 mm 2 ft. 610 mm

1 ft. 305 mm 2 ft. 610 mm 2 ft. 610 mm 4 ft. 1.2 m 3 ft. 914 mm 9 ft. 2.7 m 4 ft. 1.2 m 18 ft. 5.5 m 5 ft. 1.5 m 20 ft. 6.1 m

+ H1 + H2 = 40 ft. (12.2 m) Maximum

H1 + H2 = 20 ft. (6.1 m) Maximum

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0824

Page 25

Top Vent - Horizontal Termination - (continued)

Three Elbows

V1 Min. H1 Max. V2 Min. H2 Max.

Elbow only 2 ft. 610 mm 0 in. 0 mm 1 ft. 305 mm

6 in. 152 mm 3 ft 914 mm 6 in. 152 mm 2 ft. 610 mm

1 ft. 305 mm 6 ft. 1.8 m 1 ft. 305 mm 6 ft. 1.8 m 2 ft. 610 mm 11 ft.* 3.4 m* 2 ft. 610 mm 10 ft.* 3.1 m* 3 ft. 914 mm 16 ft * 4.9 m* 3 ft. 914 mm 14 ft.* 4.3 m*

+ H2 = 20 ft. (6.1 m) Maximum V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum

Figure 7.5

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 25

Page 26

Top Vent - Vertical Termination

Flue Restrictor Instructions

No Elbow

V1 = 40 ft. Max. (12.4 m)

V1 = 3 ft. Min. (914 mm)

Note: If installing a vertical vent/

termination off the top of the appliance, the ﬂ ue restrictor should be used.

1. Remove the top piece of refractory, if already installed. See Figure 7.7.

TOP

REFRACTORY

Figure 7.7

FLUE

RESTRICTOR

Figure 7.6

2. Break the ﬂ ue restrictor into two pieces. Do this by bending the part back and forth until it breaks (see

Figure 7.8).

BREAK

HERE

Figure 7.8 Flue Restrictor

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0826

Page 27

Top Vent - Vertical Termination (continued)

3. Match the amount of vertical you have in the system with the chart to ﬁ nd the appropriate position to set the Flue Restrictor (see Figure 7.9).

4. Center the Flue Restrictor on vent and secure in place by using two self-tapping screws (see Figure 7.10).

5. Reinstall the Exhaust Shield.

Vertical

4 ft. 1-1

8 ft. 2-2 1-2 1-1

TOP VENT REAR VENT

NG LP NG LP

RestrictorNoRestrictorNoRestrictor

Restrictor

15 ft. 3-3 3-2 2-2 1-2

20 ft. 3-4 3-3 3-3 2-3

25 ft. 3-4 3-3 3-3 2-3

30 ft. 4-4 3-4 3-4 3-3

35 ft. 4-4 3-4 3-4 3-3

40 ft. 5-4 4-4 4-4 3-4

Figure 7.9

Note: If the DVP-2SL or DVP-SLP24 adapter is used with



SLP pipe, you MUST subtract one number from the table above.

Example: Top vent 40 ft vertical with DVP pipe = 5-4

Top vent 40 ft vertical with SLP pipe = 4-3

1 2 3 4 5

SETTING

1 2 3 4 5

Figure 7.10

Two Elbows

Maximum V2V1 + V2 Min.

Elbow only 2 ft. 610 mm * * * 6 in. 152 mm 6 ft. 1.8 m * * * 2 ft. 610 mm 11 ft. 3.4 m * * * 3 ft. 914 mm 16 ft. 4.9 m * * * 4 ft. 1.2 m 20 ft 6.1 m * * *

+ V2 + H1 = 50 ft (15.2 m) Maximum

*No speciﬁ c restrictions on this value EXCEPT

V1 + V2 + H1 cannot exceed 50 ft (15.2 m)

Figure 7.11

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 27

Page 28

Top Vent - Vertical Termination - (continued)

Three Elbows

H1 + H

V2V1 + V2 Minimum H1 + H2 Maximum

Elbow only 1 ft. 305 mm * * * 1 ft. 305 mm

6 in. 152 mm 2 ft. 610 mm * * * 2 ft. 610 mm

1 ft. 305 mm 2 ft. 610 mm * * * 2 ft. 610 mm 2 ft. 610 mm 4 ft. 1.2 m * * * 4 ft. 1.2 m 3 ft. 914 mm 9 ft. 2.7 m * * * 9 ft. 2.7 m 4 ft. 1.2 m 18 ft. 5.5 m * * * 18 ft. 5.5 m

+ H2 = 20 ft (6.1 m) Maximum V1 + V2 + H1 + H2 = 40 ft (12.2 m) Maximum

Figure 7.12

INSTALLED

HORIZONTALLY

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0828

Page 29

Rear Vent - Horizontal Termination

No Elbow

Figure 7.13

H1 = 16 in. (406 mm) Maximum

One 45º Elbow

Do not use a 45º elbow in corner installations. Use two 90º elbows instead.

Figure 7.14

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 29

Page 30

Rear Vent - Horizontal Termination - (continued)

Two Elbows

H1 Maximum V1 Minimum H

1 ft. 305 mm

Back to Back

90º Elbows

1 ft. 305 mm 2 ft. 610 mm

H1 + H2 Maximum

2 ft. 610 mm 6 in. 152 mm 2 ft. 610 mm 4 ft. 1.2 m 3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m 3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m 3 ft. 914 mm 4 ft 1.2 m 18 ft. 5.5 m 20 ft.* 6.1 m*

+ H1 + H2 = 40 ft (12.2 m) Maximum H1 = 3 ft (914 mm) Maximum

*H1 + H2 = 20 ft (6.1 m) Maximum

Figure 7.15

Three Elbows

INSTALLED

HORIZONTALLY

Maximum V1 Minimum H2+ H

1 ft. 305 mm

Back to Back

90º Elbows

1 ft. 305 mm 2 ft. 610 mm

H1+ H2+ H3 Max.

2 ft. 610 mm 6 in. 152 mm 1.5 ft. 457 mm 3.5 ft. 1.1 m 3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m 3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m 3 ft. 914 mm 4 ft. 1.2 m 12 ft. 3.7 m 15 ft. 4.6 m V

+ H1+ H2+ H3= 40 ft (12.2 m) Maximum H1= 3 ft (914 mm) Maximum

H1+ H2+ H3= 20 ft (6.1 m) Maximum

Figure 7.16

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0830

Page 31

Rear Vent - Vertical Termination

One Elbow

Figure 7.17

V1 Minimum H1 Maximum

6 in. 152 mm 2 ft. 610 mm

1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 7 ft. 2.1 m 4 ft. 1.2 m 8 ft 2.4 m 5 ft. 1.5 m 8 ft 2.4 m

+ H1 = 40 ft (12.2 m) Maximum

= 8 ft (2.4 m) Maximum

Two Elbows

+ H2 Maximum V1 Minimum

Back to Back 90º Elbows 3 ft. 914 mm

2 ft 610 mm 6 ft. 1.8 m 4 ft 1.2 m

9 ft. 2.7 m 6 ft. 1.8 m 12 ft. 3.7 m 8 ft. 2.4 m 15 ft. 4.6 m

V1 + H1 = 40 ft (12.2 m) Maximum

+ H2 = 8 ft (2.4 m) Maximum

INSTALLED

HORIZONTALLY

Figure 7.18

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 31

Page 32

Rear Vent - Vertical Termination - (continued)

Three Elbows

H1 Maximum V1 Minimum H

2 ft. 610 mm 6 in. 152 mm 2 ft.

610 mm

H1 + H2 Maximum

4 ft. 1.2 m

3 ft. 914 mm 1 ft. 305 mm 4 ft. 1.2 m 7 ft. 2.1 m 5 ft. 1.5 m 2 ft. 610 mm 6 ft. 1.8 m 11 ft. 3.4 m

7 ft. 2.1 m 3 ft. 914 mm 8 ft. 2.4 m 15 ft. 4.6 m

8 ft 2.4 m 4 ft. 1.2 m 10 ft. 3.1 m 18 ft. 5.5 m

= 8 ft (2.4 m) Max. V1 + V2 + H1 + H2= 40 ft (12.2 m) Max.

H1 + H2 = 20 ft (6.1 m) Max.

Figure 7.19

Three Elbows

H1H2H

V1 Minimum H1 + H2 + H3 Maximum

*** 8 ft. 2.4 m 6 ft. 1.8 m *** 9 ft. 2.7 m 7 ft. 2.1 m ***10 ft. 3.1 m 8 ft. 2.4 m ***10 ft. 3.1 m 8 ft. 2.4 m

+ H1 + H2 + H3 = 40 ft. (12.2 m) Maximum

*No speciﬁ c restrictions on this value EXCEPT

V1 + H1 + H2 + H3 cannot exceed 40 ft. (12.2 m) Maximum

H1 + H2 + H3 = 8 ft. (2.4 m) Maximum

Figure 7.20

INSTALLED

HORIZONTALLY

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0832

Page 33

Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles:

• Between ceiling ﬁ restops

• Between wall shield ﬁ restops

• Around vent system Failure to keep insulation or other material away from

vent pipe may cause over heating and ﬁ re.

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).

• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick.

• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.

• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to 194 mm thick).

• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed. If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.

(DVP-SLP Pipe Shown)

3 in. (76 mm) top clearance

1 in. (25 mm) clearance around vertical sections

Heat Shield

Wall

Shield

Firestop

3 in. (76 mm) top clearance *

Heat Shield

1 in. (25 mm) clearance bottom & sides

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield ﬁ restop(s). The wall shield ﬁ restop maintains minimum clearances and prevents cold air inﬁ ltration.

• The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.

• SLP pipe - A wall shield ﬁ restop must be placed on each side of an interior wall. A minimum 1-1/2 in. (38 mm) overlap of attached heat shields must be maintained.

• DVP pipe - A wall shield ﬁ restop is required on one side only on interior walls. If your local inspector requires a wall shield ﬁ restop on both sides, then both wall shield ﬁ restops must have a heat shield (refer to Section 16.B.) attached to them.

• See Section 10.M. for information for regarding the installation of a horizontal termination cap.

Non-Combustible Wall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable.

Whenever a non-combustible wall is penetrated, the wall shield ﬁ restop is only required on one side and no heat shield is necessary.

WALL

Heat Shield

Wall

Shield

Firestop

WALL

* When using SLP or SL-D pipe, minimum clearances from the vent pipe to combus-

tible materials at inside wall firestops are: T op: 2-1/2 in. (64 mm) Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm)

Figure 8.1 Horizontal Venting Clearances To Combustible Materials

3 in. (76 mm) top clearance *

Heat Shield

1 in. (25 mm) clearance bottom & sides

10 in.

Inches 42-3/4 27-7/8 41-3/4 26-7/8

* Shows center of vent framing hole for top or rear venting. The center of the

hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.

Figure 8.2 Wall Penetration

10 in.

12 in.

A* B* C D

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 33

Page 34

C. Install the Ceiling Firestop

A ceiling ﬁ restop MUST be used between ﬂ oors and attics.

• DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ﬂ oor (see Figure 8.3).

• SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/ﬂ oor (see Figure 8.3).

• Frame the area with the same sized lumber as used in ceiling/ﬂ oor joist.

• The ceiling ﬁ restop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between ﬂ oors that are not insulated. Refer to Figure 8.4.

• Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu-

lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

ATTIC ABOVE

Figure 8.3 Installing Ceiling Firestop

INSTALL ATTIC INSULATION SHIELDS

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

PIPE DVP SLP

10 in. (254 mm)

9 in. (229 mm)

3 FASTENERS

PER SIDE

CEILING FIRESTOP

INSTALLED BELOW CEILING

Figure 8.4 Installing the Attic Shield

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0834

CEILING FIRESTOP

INSTALLED ABOVE CEILING

Page 35

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet speciﬁ ed clearance and be se- cured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

• Wrap shield around pipe if pipe is already installed in area to be insulated.

• Match the three holes in each side and fasten with three screws to form a tube.

• Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling ﬁ restop.

• Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling ﬁ restop and attach to the ﬁ restop.

• Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Vaulted Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

• Cut the attic insulation shield (if application is for vaulted ceiling) to ﬁ t your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

• Wrap shield around pipe if pipe is already installed in area to be insulated.

• Match the three holes in each side and fasten with three screws to form a tube.

• Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling ﬁ restop.

• Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling ﬁ restop and attach to the ﬁ restop.

• Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90° TO MAINTAIN CLEARANCE AND PREVENT INSULATION FROM FALLING INSIDE

BEND 3 TABS OUTWARD TO FASTEN TO CEILING FIRESTOP-BEND REMAINING TABS INWARD 90 DEGREES TO MAINTAIN

INSERT 3 SCREWS

Figure 8.5 Attic Insulation Shield

CLEARANCE

E. Installing the Optional Heat-Zone-Gas Kit

• Remove the knockout from the ﬁ replace and discard it (see Figure 8.6).

• Center the duct collar around the exposed hole and attach it to the ﬁ replace with 3 screws. Note: Do this BEFORE ﬁ nal positioning of ﬁ replace.

• Determine the location for the air register/fan housing assembly.

Reference the Heat-Zone-Gas kit instructions for the remaining installation steps.

HEAT-ZONE-GAS ATTACHES HERE

Figure 8.6 Heat Zone Cover Plate

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 35

Page 36

A. Choosing the Top or Rear Vent

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.

Figure 9.1 For top vent, remove the two screws holding the elbow heat shield in place. Use this heat shield over the ﬁ rst elbow if applicable. For rear vent skip this step.

Appliance Preparation

Figure 9.4 Remove the seal cap.

NOTICE: Once the seal cap has been removed it CANNOT be reattached.

Figure 9.2 Cut the seal cap strap across the rectangles next to the disk.

Figure 9.3 Remove the white gasket material covering the seal cap.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0836

Figure 9.5 Remove the insulation basket and white insulation from the center vent pipe.

Proceed to Section 7. C.

Page 37

B. Rear Vent

HEADER

NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.

Figure 9.6 Remove the insulation from the outer vent pipe. For rear venting there is no insulation in the outer vent pipe.

D. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

• Sagging or loose insulation

• Insulation backing or plastic

• Framing and other combustible materials Block openings into the chase to prevent entry of blown-

in insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs.

Failure to maintain air space clearance may cause overheating and ﬁ re.

The diagram shows how to properly position and secure the appliance (see Figure 9.9). Nailing tabs are provided to secure the appliance to the framing members.

• Bend out nailing tabs on each side.

• Place the appliance into position.

• Keep nailing tabs ﬂ ush with the framing.

• Level the appliance from side to side and front to back.

• Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

• Secure the appliance to the framing by using nails or screws through the nailing tabs.

• Secure the appliance to the ﬂ oor by inserting two screws through the pilot holes at the bottom of the appliance.

Figure 9.7 To attach the ﬁ rst section of vent pipe, make sure to use the ﬁ berglass gasket in the manual bag to seal between the ﬁ rst vent component and the outer ﬁ replace wrap. Use 2 self tapping screws to secure the gasket to the outer wrap.

Secure the ﬁ rst section of venting to the ﬁ replace by screw- ing through the two straps left over from cutting the seal cap strap in step 2.

C. Installing the Non-combustible Board

The factory supplied non-combustible board spans the distance from the top of the ﬁ replace to the center of the framing header. This board must be used. See Figure 9.8.

HEADER

NAILING TABS (BOTH SIDES)

PILOT HOLES

Figure 9.9 Proper Positioning and Securing of an Appliance

Figure 9.8 Non-combustible Board

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 37

Page 38

Lances

Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only)

Attach Vent to the Firebox Assembly

Note: The end of the pipe sections with the lanced tabs will face

toward the appliance.

Attach the ﬁ rst pipe section to the starting collar:

• Lanced pipe end to the starting collar

• Inner pipe over inner collar

• Push the pipe section until all lanced tabs snap in place

• Lightly tug on pipe to conﬁ rm it has locked.

Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications

All outer pipe joints must be sealed with high temperature silicone, including the slip section that connects directly to the horizontal termination cap.

• Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 10.1

• Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer ﬂ ues shall be sealed in this manner, unless otherwise stated.

Figure 10.1 High Temperature Silicone Sealant

Lances

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Assemble Pipe Sections

Per Figure 10.2:

• Start the inner pipe on the lanced end of section A into the ﬂ ared end of section B.

• Start the outer pipe of section A over the outer pipe of section B.

• Once both vents sections are started, push ﬁ rmly until all lanced tabs lock into place.

• Lightly tug on the pipe to conﬁ rm the tabs have locked.

It is acceptable to use screws no longer than 1/2 in. (13 mm) to hold outer pipe sections together. If predrilling holes, DO NOT penetrate inner pipe.

For 90º and 45º elbows that are changing the vent direction from horizontal to vertical, one screw minimum should be put in the outer ﬂ ue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1/2 in. (13 mm). If predrilling screw holes, DO NOT penetrate inner pipe.

Figure 10.2

Note: Make sure that the seams are not aligned to prevent

unintentional disconnection.

CORRECT

Figure 10.3

Figure 10.4 Seams

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0838

INCORRECT

Page 39

B. Assemble Vent Sections (SLP Pipe Only)

Pilot hole

To attach the ﬁ rst vent component to the starting collars of the appliance:

• Attach a DVP-2SL or DVP-SLP24 adapter to the starting



collar of the appliance.

• Lock the vent components into place by sliding the pipe section onto the collar.

• Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 10.5.

• Slide the gasket over the ﬁ rst vent section and place it ﬂ ush to the appliance. This will prevent cold air inﬁ ltration. High temperature caulk may be used to hold the part in place.

• Continue adding vent components, locking each succeeding component into place.

• Ensure that each succeeding vent component is securely ﬁ tted and locked into the preceding component.

Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications

For Installation into a commercial, multi-family (multi-level exceeding two stories) or high-rise applications: All outer pipe joints must be sealed with high temperature silicone, including the slip section that connects directly to the horizontal termination cap.

• Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 10.1.

• Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer ﬂ ues shall be sealed in this manner, unless otherwise stated.

C. Assemble Slip Sections

• Slide the inner ﬂ ue of the slip section into the inner ﬂ ue of the pipe section and the outer ﬂ ue of the slip section over the outer ﬂ ue of the pipe section. See Figure 10.6.

• Slide together to the desired length.

Pilot hole

Figure 10.6 Slip Section Pilot Holes

• Maintain a 1-1/2 in. (38 mm) overlap between the slip section and the pipe section.

• Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 10.7.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 10.5 Adding Venting Components

Figure 10.7 Screws into Slip Section

• Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE: If slip section is too long, the inner and outer ﬂ ues of the slip section can be cut to the desired length.

NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a high temperature silicone sealant.

• Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

• Only outer pipes are sealed, sealing the inner ﬂ ue is not required.

• All unit collar, pipe, slip section, elbow and cap outer ﬂ ues shall be sealed.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 39

Page 40

D. Secure the Vent Sections

• Vertical runs of DVP pipe must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise.

• Vertical runs of SLP pipe must be supported every 8 ft. (2.44 m).

• Horizontal sections must be supported every 5 feet (1.52 m).

• Vent supports or plumbers strap (spaced 120º apart) may be used to support vent sections. See Figures 10.8 and 10.9.

• Wall shield ﬁ restops may be used to provide horizontal support vent sections.

• SLP ceiling ﬁ restops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

E. Disassemble Vent Sections

• Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure

10.11.

• Pull carefully to separate the pieces of pipe.

Figure 10.10 Rotate Seams for Disassembly

120º

Figure 10.8 Securing Vertical Pipe Sections

120º

Figure 10.11 Align and Disassemble Vent Sections

Figure 10.9 Securing Horizontal Pipe Sections

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0840

Page 41

F. Install Decorative Ceiling Components

(SLP only)

A decorative ceiling thimble can be installed on a ﬂ at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the ﬁ restop.

• Seal the gap between the vent pipe and ﬁ restop using high temperature silicone to prevent cold air inﬁ ltration.

• Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.

A decorative cathedral ceiling support box can be installed on a cathedral ceiling through which the vent passes.

• Use a plumb-bob to mark the center line of the venting system on the ceiling and drill a small hole through the ceiling and roof at this point. Locate the hole and mark the outline of the cathedral ceiling support box on the outside roof.

• Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

• Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure

10.12).

• Level the support box both vertically and horizontally and temporarily tack it in place through the inside walls into the roof sheathing.

• Use tin snips to cut the support box from the top corners down to the roof line and fold the resulting ﬂ aps to the roof. See Figure 10.13.

• Nail the ﬂ aps to the roof AFTER running a bead of non hardening sealant between the ﬂ aps and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

LEVEL

CATHEDRAL CEILING SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm) GREATER IN SIZE THAN PATTERN OF SUPPORT BOX AS IT IS PROJECTED ONTO ROOF LINE

Figure 10.12

Figure 10.13

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 41

Page 42

G. Install Metal Roof Flashing

Figure 10.16 Assembling the Storm Collar

Figure 10.17 Assembling the Storm Collar Around the Pipe

Figure 10.15

Note: Skip this section if using the RF4-8.

• See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof.

• Slide the roof ﬂ ashing over the pipe sections extending through the roof as shown in Figure 10.15.

HORIZONTAL

OVERHANG

CAULK

2 FT. MIN.

GAS DIRECT VENT TERMINATION CAP

Roof Pitch H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12 ............................1.25*

Over 7/12 to 8/12 ..............................1.5*

Over 8/12 to 9/12 ..............................2.0*

Over 9/12 to 10/12 ............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12 ........................... 5.0

Over 14/12 to 16/12 ........................... 6.0

Over 16/12 to 18/12 ........................... 7.0

Over 18/12 to 20/12 ........................... 7.5

Over 20/12 to 21/12 ........................... 8.0

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

ROOF PITCH

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

* 3 foot minimum in snow regions

VERTICAL

WALL

IS X/ 12

Figure 10.15

H. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

• Connect both halves of the storm collar with two screws (see Figure 10.16).

• Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly . Make sure the collar is tight against the pipe section.

• Slide the assembled storm collar down the pipe section until it rests on the roof ﬂ ashing (see Figure 10.17).

• Caulk around the top of the storm collar (see Figure 10.23).

Figure 10.14 Minimum Height From Roof To Lowest Discharge

Opening

NOTICE: Failure to properly caulk the roof ﬂ ashing could cause water entry.

• Caulk the gap between the roof ﬂ ashing and the outside diameter of the pipe.

• Caulk the perimeter of the ﬂ ashing where it contacts the roof surface. See Figure 10.15.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0842

Figure 10.16 Assembling the Storm Collar

Figure 10.17 Assembling the Storm Collar Around the Pipe

Page 43

I. Install RF4-8

The RF4-8 may be used in place of the roof ﬂ ashing and storm collar (Sections 10.G. and 10.H.)

Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flashing. Refer to Section 10.D. Secure Vent Sections.

SECURE WITH 4 SCREWS NO LONGER THAN 1 IN. (25 MM)

SLP-FS

Figure 10.18 Secure Pipe with SLP-FS

Figure 10.20 Apply Sealant

• Trim the rubber boot (using scissors or a utility knife), cutting along the marked measurement lines. See Figure

10.19. Use the 150 mm line for SLP, 210 mm for DVP.

• Lubricate pipe or ﬂ ue with water and slide the ﬂ ashing down. It may be necessary to trim the top shingles around the base of the rubber boot to ensure a good ﬁ t.

• Draw a line around ﬂ ashing. Remove ﬂ ashing.

• Apply silicone sealant to roof inside the lines (Figure 10.20).

• Lubricate pipe or ﬂ ue with water and slide ﬂ ashing down. Seat ﬁ rmly in sealant. Nail roof ﬂ ashing to the roof.

• Apply silicone sealant on the top and sides edges of the ﬂ ashing. See Figure 10.21. Install shingles. Apply sealant at the top edge of the rubber boot. See Figure 10.22.

• We recommend that you top coat with conventional acrylic house paint to improve the appearance of your galvanized base ﬂ ashing.

APPLY SEALANT

TOP & PARTIAL SIDES

Figure 10.21 Slide Flashing Down, Secure & Apply Sealant

SILICONE SEALANT (TOP OF BOOT)

SHINGLES TRIMMED

Figure 10.19 Trim Rubber Boot

FLASHING OVER SHINGLES

Figure 10.22 Installation Complete

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 43

SHINGLES OVER FLASHING

Page 44

Figure 10.23

J. Install Vertical Termination Cap

• Attach the vertical termination cap by sliding the inner collar of the cap into the inner ﬂ ue of the pipe section while placing the outer collar of the cap over the outer ﬂ ue of the pipe section.

• Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer ﬂ ue of the pipe (see Figure 10.23).

TERMINATION CAP

(1 of 3)

STORM COLLAR

SCREWS

CAULK

Figure 10.23

K. Install Decorative Wall Components (SLP

only)

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the wall shield ﬁ restop.

• Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

• Once the pipe section and the termination cap have been

connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure

10.24.

L. Heat Shield Requirements for Horizontal

Termination

WARNING! Risk of Fire! To prevent overheating and ﬁ re, heat shields must extend through the entire wall thickness.

• DO NOT remove the heat shields attached to the wall shield ﬁ restop and the horizontal termination cap (shown in Figure 10.25).

• Heat shields must overlap 1-1/2 in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attached to the wall shield ﬁ restop. The other section is factory-attached to the cap. See Figure 10.25.

If the wall thickness does not allow the required 1-1/2 in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

• If the wall thickness is less than 4 in./102 mm (DVP) or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap and wall shield ﬁ restop must be trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST be maintained.

• Use an extended heat shield if the ﬁ nished wall thickness is greater than 7-1/4 in. (184 mm).

• The extended heat shield may need to be cut to length maintaining sufﬁ cient length for a 1-1/2 in. (38 mm) overlap between heat shields.

• Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

• Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields may not be ﬁ eld constructed.

Figure 10.24 Wall Thimble

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0844

Page 45

M. Install Horizontal Termination Cap (DVP

and SLP Pipe)

WARNING! Risk of Fire! The telescoping ﬂ ue section of the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of ﬂ ue telescoping section is required.

Failure to maintain overlap may cause overheating and ﬁ re.

• Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at outside edges of cap.

• When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 and CAN/CGA-B149 installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

NOTICE: For certain exposures which require superior resistance to wind-driven rain penetration, a ﬂ ashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps with factory-supplied heat shield attached, no additional wall shield ﬁ restop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

EXTENDED

WALL SHIELD

FIRESTOP

INNER VENT

OUTER VENT

VENT DEPTH FROM BACK OF APPLIANCE TO

OUTSIDE SURFACE OF EXTERIOR WALL

Figure 10.25 Venting through the wall

HEAT SHIELD

SLIP SECTION

CAN BE EXTENDED

(SEE CHART BELOW)

INTERIOR

Cap Speciﬁ cation Chart

(depth without using additional pipe sections)

DVP-TRAPK1

Top Vent

Depth

2-3/4 in. to

6000

Series

DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.) DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8) DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8) DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)

4-5/8 in.

DVP-HPC1

Top Vent

Depth

2-3/4 in. to

4-7/8 in.

DVP-TRAP1

Rear Vent

Depth

3-1/8 in. to

5 in.

DVP-HPC1

Rear Vent

Depth

3-1/8 in. to

5-1/4 in.

DVP-TRAPK2

Top Vent

Depth

5-1/8 in. to

9-1/8 in.

DVP-HPC2

Top Vent

Depth

4-7/8 in. to

9 in.

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

DVP-TRAP2

Rear Vent

Depth

5-1/2 in. to

9-1/2 in.

DVP-HPC2

Rear Vent

Depth

5-1/4 in. to

9-3/8 in.

EXTERIOR

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 45

Page 46

Gas Information

A. Fuel Conversion

• Make sure the appliance is compatible with available gas types.

• Conversions must be made by a qualified service technician using Hearth & Home T echnologies speciﬁ ed and approved parts.

B. Gas Pressure

• Optimum appliance performance requires proper input pressures.

• Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

• Pressure requirements are:

Gas Pressure Natural Gas Propane

Minimum inlet pressure 5.0 in. w.c. 11.0 in. w.c. Maximum inlet pressure 14.0 in. w.c. 14.0 in. w.c. Manifold pressure 3.5 in. w.c. 10.0 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

• Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard. High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

• Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualiﬁ ed installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve and ﬂ exible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.

• If substituting for these components, please consult local codes for compliance.

C. Gas Connection

• Refer to Reference Section 16 for location of gas line access in appliance.

• Gas line may be run through knockout(s) provided.

• The gap between supply piping and gas ac cess hole may be caulked with high temperature caulk or stuf fe d with non-combustible, unfaced insulation to prev ent cold air inﬁ ltration.

• Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

• Pipe incoming gas line into valve compartment.

• Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up dur ing line purge could ignite.

• Purge should be performed by qualified service

technician.

• Ensure adequate ventilation.

• Ensure there are no ignition sources such as sparks

or open ﬂ ames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all ﬁ ttings and connections with a non-corrosive commercially available leak-check solution. DO NOT use open ﬂ ame. Fittings and connections could have loos- ened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce burner oriﬁ ce 4% for each 1000 feet above 2000 feet.

• In CANADA: Reduce burner oriﬁ ce 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0846

Page 47

Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.

• Wire the appliance junction box to 110-120 VAC. This is required for proper operation of the appliance.

• A 1 10-120 V AC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

• Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 1 10V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

B. Intelliﬁ re Ignition System Wiring

• Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

• Refer to Figure 12.1, Intelliﬁ re Pilot Ignition (IPI) Wiring Diagram.

• This appliance is equipped with an Intelliﬁ re control valve which operates on a 3 volt system.

• Plug the 3-volt AC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

C. Optional Accessories Requirements

• This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home T echnologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 47

Page 48

NOT

USED

BATTERY

PACK

WALL

SWITCH

BACK VIEW

T O GROUND CLIP

WHT

BLK

ORG

NOT

CONNECTED

CONNECT TO ORIFICE SOLENOID

RED WIRE TO RED WIRE

BLACK WIRE TO BLACK WIRE

F.O.L. CAPACITOR

PART IS ENCLOSED

IN SHRINK TUBING

CORD

ASSEMBLY

Figure 12.1 Intelliﬁ re Pilot Ignition (IPI) Wiring Diagram

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0848

Note: Appliance will not operate unless properly grounded.

WARNING! Risk of Shock! Replace damaged wire with type 105º C rated wire. Wire must have high temperature insulation.

Page 49

E. Junction Box Installation

If the box is being wired from the INSIDE of the appliance:

• Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 12.2).

• Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.2.

• Make all necessary wire connections to the junction box/ receptacle and reattach the junction box/receptacle to the outer shell.

WHT

BLK

WHT

BLK

Figure 12.2 Junction Box Detail

Romex Connector

Cover Plate outside firebox

Copper

GRN wire inside box

ground attached to GRN screw with GRN wire

NOTICE: DO NOT wire 110 VAC to wall switch.

14/2WG

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.3):

• The power supply for the appliance must be brought into a switch box.

• The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire.

• At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

• At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

• Add a 1/4 in. insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 in. male) as shown.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 49

Minimum 14-3 AWG with Ground

Junction Box

Red

Figure 12.3 Junction Box Wired to Wall Switch or BC10

Red

Black

White

Red

Green

Black

White

Green

Knockout

Switch Box

Black

White

Switch

Green

Power Supply

Wires

Page 50

Finishing

A. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as speciﬁ ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause ﬁ re.

Combustible Mantels

TO CEILING

Note: All measurements in inches.

2-1/2

B. Facing Material

• Metal front faces may be covered with non-combustible materials only.

• Facing and/or ﬁ nishing materials must not interfere with air ﬂ ow through louvers, operation of louvers or doors, or access for service.

• Facing and/or ﬁ nishing materials must never overhang into the glass opening.

• Observe all clearances when applying combustible materials.

• Seal joints between the ﬁ nished wall and appliance top and sides using a 300 ºF minimum sealant. Refer to Figure 13.3.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speciﬁ ed in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

NON-COMBUSTIBLE ZONE (Shaded areas)

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Note: Measurement is taken from top of the opening, NOT the top of the ﬁ replace.

Figure 13.1 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

Combustible Mantel Legs or Wall Projections

INTERIOR WALL

TOP VIEW

FIREPLACE OPENING

MANTEL LEG OR WALL PROJECTIONS

If A minimum is ____, then B maximum is_____.

Inches

2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16

Millimeters

Inches

Millimeters

62 87 113 138 164 189

12345

25 51 76 102 127

41 in.

39-3/8 in.

Figure 13.3 Noncombustible Facing Diagram

∞

Figure 13.2 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0850

Page 51

C. Doors

Only doors certiﬁ ed for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. Once you have determined what kind of door and ﬁ nishing material is going to be used on the ﬁ replace, you may use the table below which shows the door models and the ﬁ nishing material thickness allowed. For an inside ﬁ t there is an available template to assist with siz- ing the ﬁ nishing material.

FINISH

DOOR FIT

MATERIAL

MAXIMUM

THICKNESS

Folio Inside Any 13.4

Arcadia

Halston

Chateau

Valencia

Galleria

Overlap 1 inch 13.5

Inside Any 13.6

Overlap 1 inch 13.5

Inside 1 inch - 3 inch 13.7

Overlap 1 inch 13.5

Inside Any 13.6

Overlap 1 inch 13.5

Inside Any 13.6

Overlap 1 inch 13.5

Inside 1 inch - 3 inch 13.7

SEE

FIGURE

FINISHING

MATERIAL

DOOR

37-1/4 in.

(Includes 1/8 in. opening each side of door)

(Outside door width)

(Includes 1/8 in. opening each side of door)

Finishing materials over 1 inch thick.

Figure 13.6 Inside ﬁ t door

ELBOW

HEAT

SHIELD

37 in.

(Outside door width)

33-3/4 in.

37 in.

37-1/4 in.

FINISHING MATERIAL

34 in.

Stop ﬁ nishing material ﬂ ush with opening.

Figure 13.4 Folio Door

ELBOW

HEAT

SHIELD

1-2 IN. THICK

FINISHING MATERIAL

*IF FINISHING MATERIAL IS THICKER THAN

2 IN., DOORS WILL ONLY OPEN

AS FAR AS PICTURED

DOORS

33 3/4 IN.

37 1/4 IN.

Finishing material between 1 and 3 inches thick.

Figure 13.7 Operable hinge door

1-2 IN. THICK

FINISHING MATERIAL

34 IN.

Finishing materials 1 inch maximum thick. Stop ﬁ nishing material ﬂ ush with opening.

Figure 13.5 Overlap Fit Door

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 51

Page 52

Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14.H.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁ rebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁ rebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Install the Refractory

Note: The red refractory will naturally darken when the

ﬁ rebox heats up. The red color will return when the ﬁ rebox cools.

STEP 1.

Place the back piece of refractory in back of the ﬁ rebox. The small indentation on one side goes down. Lean the refractory slightly so it doesn’t tip over.

STEP 2.

Place the left side refractory onto the left side of the burner. Push the back refractory against the back wall. Place the bumps on the bottom of the left refractory into the grooves on the burner surface. Push to top gently against the side of the ﬁ replace. Once in place push it back so the bevel cuts sit against each other and the seam is minimized.

Figure 14.2

STEP 3.

Repeat step 2 for the right side.

Figure 14.1

Figure 14.3

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0852

Page 53

STEP 4.

Refer to the details in Figure 14.5 to position Optional Refractory Standoff Bracket.

Note: If ﬁ replace is rear vented and has no elbows in the vent run, adjusting the refractory standoff bracket is allowed. If any elbows are used in the vent run, DO NOT adjust the refractory standoff bracket.

• Remove screw shown in Detail A.

• Bend down back ﬂ ap along the two (2) perforations to break back ﬂ ap from refractory standoff bracket. See Detail B.

• Rotate the separated piece and bend the back ﬂ ap as shown in Detail C to enable the tabs to ﬁ t into the two (2) holes on the left and right of the refractory standoffs indicated in Detail D.

• Verify that the back ﬂ ap rests on top of left and right refractory standoff tabs noted in Detail E.

Refractory Standoff Bracket

DETAIL A.

Back Flap

Screw

Figure 14.5

F. Ember Placement

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually . Improperly placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. T o place the ember material:

• Embers CANNOT be placed directly over ports. Care should be taken not to cover the lighting trail of ports (from back to front).

• Place dime-size pieces of Glowing Embers® just in front of the port trail, but not on or in between the ports (see Figure 14.6). Care should be taken so that the ports are not covered. Failure to follow this procedure will likely cause lighting and sooting problems.

BEND

DETAIL B. DETAIL C.

Left

DETAIL D.

Figure 14.4

Right

Left

DETAIL E.

Right

STEP 5.

Hold the top refractory with the brick pattern facing down. Bring the back edge into the ﬁ rebox slightly higher than the front edge. Bring the back edge all the way to the metal back wall of the ﬁ replace. Raise the front edge up until it clears the side refractory pieces. Drop the back edge down and nest the sides and back into the groove around the edges of the top piece of refractory.

EMBER MATERIAL

Figure 14.6 Placement of Embers

• Place Mystic Embers on areas of base refractory away from port holes. Use this material to give the appliance a realistic ash bed.

• Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 53

Page 54

G. Install the Log Assembly

Figure 14.8

Figure 14.10 Top View

Figure 14.7

Figure 14.9 Front View

HUMP

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

STEP 1. CAUTION: Logs are fragile! Carefully

remove the logs, grate and supporting cardboard from the inside of the fireplace See Figure

14.7.

Figure 14.7

Log Assembly: LOGS-6000GLX

LOGS-6000GLXLP

STEP 2. Place the metal grate on top of the

burner. Position the legs of the grate into the forward set of indentations in the burner top, sliding the grate forward. See Figure 14.8.



Figure 14.8

HUMP

Figure 14.10 Top View

Figure 14.9 Front View

STEP 3. Log #1 NG (SRV2101-085): Log #1 LP (SRV2101-087): Log #1 is the left burning log. The air shut-

ter in the end of the burner tube goes over the left brass oriﬁ ce located behind the main burner. The left end of the log goes tight against the left refractory wall. See Figures 14.9 and 14.10.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0854

2101-910

Page 55

Figure 14.12 Top View

Figure 14.14 Top View

Figure 14. 16 Top View

Figure 14.13 Front View

Figure 14.11 Front View

Figure 14.15 Front View

Figure 14.12 Top View

Figure 14.11 Front View

STEP 4. Log #2 NG (SRV2101-086): Log #2 LP (SRV2101-088): Log #2 is the right burning log. The air

shutter in the end of the burner tube goes over the right brass oriﬁ ce located behind the main burner. The right end of the log goes tight against the right refractory wall.

Figure 14.13 Front View

Figure 14.14 Top View

STEP 5. Log #3 (SRV2101-197): Place log #3 on top of the burner surface in front of the hump. Slide it back against

the hump and the “V” notch in the bottom of the log rests into the second grate tine from the left.

Figure 14.15 Front View

Figure 14. 16 Top View

STEP 6. Log #4 (SRV386-716): Place log #4 on top of the left side of log #2. The bottom of this log has a slot in it

that goes over the tab molded into the top of log #2. The other end of the log rests in the ﬂ at area on top of log #3.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 55

Page 56

Figure 14.18 Top View

Figure 14.20 Top View

Figure 14.22 Top View

Figure 14.19 Front View

Figure 14.21 Front View

Figure 14.17 Front View

Figure 14.18 Top View

Figure 14.17 Front View

STEP 7. Log #5 (SRV2101-195): Place log #5 on top of log #1 and log #4. The bottom of this log has two slots in it

that both go over the two tabs molded in the top of log #1.

Figure 14.19 Front View

Figure 14.20 Top View

STEP 8. Log #6 (SRV2101-196): Place log #6 on top of log #2 and the grate. There is a slot in the bottom of this

log. Place the slot over the tab on top of the right end of log #2. The end of this log has a square notch in it that rests into the second tine from the right on the grate. Note: May be necessary to tilt grate forward to interlock bottom notch in log.

Figure 14.21 Front View

Figure 14.22 Top View

STEP 9. Log #7 (SRV530-703): Place log #7 on top of log #1 and the grate. The lower right end of the log rests

against the second tine from the left on the grate.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0856

Page 57

H. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle ﬁ xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

• DO NOT strike, slam or scratch glass.

• DO NOT operate ﬁ replace with glass removed, cracked,

broken or scratched.

• Replace as a complete assembly.

Removing Fixed Glass Assembly

• Pull the four glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance

(see Figure 14.23).

Replacing Fixed Glass Assembly

• Replace the glass door on the appliance. Pull out and latch the four glass assembly latches into the groove on the glass frame.

K. Air Shutter Setting

Air shutter settings should be adjusted by a qualiﬁ ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.24.

• Loosen the wing nut.

• Push the air handle in to close the air shutter.

• Pull the air handle out to open the air shutter.

• Tighten the wing nut.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

LATCHES

(BOTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

Figure 14.23 Fixed Glass Assembly

I. Install the Mesh

Screen mesh is supplied with the optional doors.

J. Install Trim and/or Surround

• Install optional trim kits and/or surrounds using the instructions included with the accessory.

• Use non-combustible materials to cover the gap between the sheet rock and the appliance (when applicable to the model).

AIR SHUTTER

Figure 14.24 Air Shutter

WING NUT

Air Shutter Settings

NG LP

Burner 3/8 in. Open Left Log 1/2 in. N/A Right Log 1/2 in. N/A

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 57

Page 58

Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualiﬁ ed service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualiﬁ ed service technician. Contact your dealer to arrange a service call by a qualiﬁ ed service technician.

A. Intelliﬁ re Ignition System

Symptom Possible Cause Corrective Action

1. Pilot won’t light. The ignitor/module makes noise, but no spark.

2. Pilot won’t light, there is no noise or spark.

A. Incorrect wiring. Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

connected to correct terminals on module and pilot assembly.

B. Loose connections or electrical

shorts in the wiring.

C. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be

D. Module. Turn ON/OFF rocker switch or wall switch to OFF position. Remove

A. No power or transformer installed

incorrectly.

B. A shorted or loose connection in

wiring conﬁ guration or wiring har- ness.

Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly are tight; also verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure, mesh screen if present, or any other metal object.

approximately .17 in. or 1/8 in. (3 mm).

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5 mm) away from “I” terminal on module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is ﬁ ne. Inspect pilot assembly for shorted sparker wire or cracked insulator around electrode. Replace pilot if necessary .

Verify that transformer is installed and plugged into module. Check voltage of transformer under load at spade connection on module with ON/OFF switch in ON position. Acceptable readings of a good transformer are between 3.2 and 2.8 volts AC.

Remove and reinstall the wiring harness that plugs into module. Verify there is a tight ﬁ t. Verify pilot assembly wiring to module. Re- move and verify continuity of each wire in wiring harness. Replace any damaged components.

3. Pilot sparks, but Pilot will not light.

C. Improper wall switch wiring. Verify that 110/VAC power is “ON” to junction box. D. Module not grounded. Verify black ground wire from module wire harness is grounded to

metal chassis of appliance.

E. Module. Turn ON/OFF rocker switch or wall switch to OFF position. Remove

ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is ﬁ ne. Inspect pilot assembly for shorted sparker wire or cracked insulator around electrode.

A. Gas supply. Verify that incoming gas line ball valve is “open”. Verify that inlet

pressure reading is within acceptable limits, inlet pressure must not exceed 14 in. W.C.

B. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be

approximately .17 in. or 1/8 in. (3 mm). C. Module is not grounded. Verify module is securely grounded to metal chassis of appliance. D. Module voltage output / Valve/Pilot

solenoid ohms readings.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0858

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

age is below 2.7.

Page 59

Intelliﬁ re Ignition System - (continued)

Symptom Possible Cause Corrective Action

4. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot ﬂ ame has been lit, ﬂ ame rectiﬁ cation has not occurred.)

A. A shorted or loose connection in ﬂ ame

sensing rod.

B. Poor ﬂ ame rectiﬁ cation or contaminated

ﬂ ame sensing rod.

C. Module is not grounded. Verify module is securely grounded to metal chassis of ap-

D. Damaged pilot assembly or contami-

nated ﬂ ame sensing rod.

E. Module. Turn ON/OFF rocker switch or wall switch to OFF position.

Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal object.

With ﬁ xed glass assembly in place, verify that ﬂ ame is en- gulﬁ ng ﬂ ame sensing rod on left side of pilot hood. Flame sensing rod rect pilot oriﬁ ce is installed and gas inlet is set to pressure speciﬁ cations. Clean ﬂ ame sensing rod with emery cloth to remove any contaminants that may have accumulated on ﬂ ame sensing rod.

pliance. Verify that wire harness is ﬁ rmly connected to the module.

Verify that ceramic insulator around the ﬂ ame sensing rod is not cracked, damaged, or loose. Verify connection from ﬂ ame sensing rod to white sensor wire. Clean ﬂ ame sensing rod with emery cloth to remove any contaminants that may have accumulated on ﬂ ame sensing rod. Verify continuity with a multimeter with ohms set at lowest range. Replace pilot if any damage is detected.

Remove ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is ﬁ ne.

should glow shortly after ignition. Verify cor-

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 59

Page 60

Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only . For framing dimensions and clearances refer to Section 5.

GAS LINE

ACCESS

Location Inches Millimeters

A 41 1041 B 36-1/8 918 C 33-1/2 851 D 34-5/8 879 E 2-3/8 60 F 5 127

G 26-7/8 683

H 8 dia 203

I 21-1/2 546

TOP VIEW

ELECTRICAL

ACCESS

B A

RIGHT SIDELEFT SIDE FRONT VIEW

Location Inches Millimeters

J 11-5/8 295 K 28-1/2 724 L 14-1/4 362

M 8 dia 203

N 2-1/8 54

O 6-7/8 175

P 38 965

Q1 25

R 39-3/8 1000

Figure 16.1 Appliance Dimensions

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0860

Page 61

B. Vent Components Diagrams

DVP Pipe (see chart)

10 in.

(254 mm)

24 in.

(610 mm)

Effective

Height/Length

10 in.

(254 mm)

Pipe

DVP4 4 102 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610

Effective Length

Inches Millimeters

10 in.

(254 mm)

1 in.

(25 mm)

10-1/2 in. (267 mm)

4-7/8 in.

( 276 mm)

9-1/4 in.

(235 mm)

13-1/4 in. (337 mm)

10-7/8 in. (276 mm)

DVP45 (45º Elbow)

11-3/8 in. (289 mm)

7-3/8 in.

(187 mm)

1-1/4 in. (32 mm)

1/2 in.

TYP

(13 mm)

DVP-AS (Attic Shield)

10 in.

(254 mm)

5 in.

(127 mm)

DVP-HVS (Vent Support)

Figure 16.2 DVP vent components

DVP-FS (Ceiling Firestop)

1- 1/2 in.

(38 mm)

12 in.

(305 mm)

14 in.

(356 mm)

DVP90ST (90° Elbow)

12 in.

(305 mm)

6 in.

(152 mm)

DVP-WS (Wall Shield Firestop)

1 in. (25 mm)

8 in.

(203 mm)

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 61

Page 62

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the

existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required.

15-1/8 in. (384 mm)

12 in.

(305 mm)

DVP-TRAP

Horizontal Termination Cap

8 in.

(203 mm)

Max

Effective

Length

Heat

Shield

Term Cap

Trap1

Trap2

Minimum

Effective Length

3-1/8 in. 4-5/8 in.

79 mm 117 mm 5-3/8 in. 9-3/8 in. 137 mm 238 mm

Effective Length

Maximum

DVP-TRAP1

DVP-TRAPK1

DVP-HPC1

DVP-TRAP2

DVP-TRAPK2

DVP-HPC2

Figure 16.3 DVP vent components

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0862

Page 63

B. Vent Components Diagrams (continued)

13-1/4 in.

(367 mm)

31 in.

(787 mm)

24-5/8 in.

(625 mm)

24-5/8 in.

(625 mm)

13-3/4 in. (349 mm)

RF6M

Roof Flashing Multi-pak

13-3/4 in. (349 mm)

BEK

Trap Cap Brick Extension

27-1/2 in.

(127 mm)

5 in.

(127 mm)

13-7/8 in.

(352 mm)

13-1/4 in.

(367 mm)

RF12M

Roof Flashing Multi-pak

11-7/8 in.

(302 mm)

DVP-BEK2

DVP-HPC Cap Brick Extension

5 in.

(127 mm)

DVP-TRAPFL

Flashing

26 in.

660 mm

DVP-HSM-B Extended Heat Shield

Figure 16.4 DVP vent components

7-1/8 in.

(181 mm)

11-5/8 in. (295 mm)

5-3/4 in.

(146 mm)

14 in.

(356 mm)

12-1/8 in. (308 mm)

COOL-ADD

Cap Shield

13-7/8 in. (352 mm)

DRC-RADIUS

9-1/2 in.

(241 mm)

Cap Shield

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 63

Page 64

B. Vent Components Diagrams (continued)

7-3/8 in.

(187 mm)

1-1/2 in.

(38 mm)

14 in.

(356 mm)

12 in.

(305 mm)

DVP-TB1

BasementVent Cap

PVK-80

(For use with IPI and DSI appliances only.)

17-3/4 in.

(451 mm)

12 in.

305 mm

7-1/4 in.

(184 mm)

12-1/2 in.

(318 mm)

5-1/4 in.

(133 mm)

DVP-TVHW

VerticalTermination Cap (Highwind)

16-7/8 in. (429 mm)

12 in.

(305 mm)

12-1/8 in. (314 mm)

1-5/8 in. (41 mm)

High Performance Cap

Figure 16.5 DVP vent components

7-1/8 in.

(181 mm)

DVP-HPC

8-3/4 in.

(222 mm)

14 in.

(356 mm)

1 in.

(25 mm)

14 in.

(356 mm)

7-1/4 in.

(184 mm)

3/8 in. (10 mm)

1 in. (25 mm)

7-3/4 to 10-3/8 in.

(197 to 264 mm)

DVP-FBHT

FireBrickTermination Cap

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0864

Page 65

B. Vent Components Diagrams (continued)

15 in.

(381 mm)

8-1/8 in.

(206 mm)

13 in.

(330 mm)

Effective Length 5-3/4 to 8-3/8 in.

146 to 213 mm

5-1/2 in. 140 mm

87°

WARNING

Fire Risk.

• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented ﬁ replaces, a 6 inch minimum vertical vent section is required before installing ﬁ rst elbow.

DVP-HRC-SS

DVP-HRC-ZC-SS

HORIZONTAL TERMINATION CAP

8-3/8 in. 213 mm

3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

Figure 16.6 DVP vent components

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 65

Page 66

B. Vent Components Diagrams (continued)

6-1/2 in. 165 mm

8-3/4 in. 222 mm

6-5/8 in. 168 mm

SLP45

45° Elbow

6 in.

152 mm

6-1/2 in. 165 mm

9-1/4 in. 235 mm

6-5/8 in. 168 mm

9-7/8 in. 251 mm

SLP-90ST 90° Elbow

Effective

Height/ Length

SLP PIPE

Effective Height/Length Pipe

SLP4 4 102

SLP6 6 152 SLP12 12 305 SLP24 24 610 SLP36 36 914 SLP48 48 1219 SLP6A 2 - 6 51 - 152

SLP12A 2 - 12 51 - 305

inches mm

DVP-SLP24

Adapter

SLP-HVS

Horizontal Pipe

Support

Figure 16.7 SLP Series Vent Components



Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0866

RF4-8

Roof Flashing

SLP-FS

Ceiling Firestop

SLP-WS

Wall Shield Firestop

Page 67

B. Vent Components Diagrams (continued)

SLP-SNKD

Snorkel

Termination Cap

SLP-TRAP1

Termination Cap

Horizontal

SLP-CCS-BK

Cathedral Ceiling

Support Box-Black

Termination Cap

SLP-TVHW

Vertical

Termination Cap

SLP-TRAP2

Horizontal

26 in.

660 mm

DVP-2SL

SLP-DCF-BK

Ceiling Firestop

Black

Figure 16.8 SLP Series Vent Components

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 67

DVP-HSM-B

Extended Heat Shield

SLP-WT-BK

Wall Thimble-Black

Page 68

C. Service Parts

6000GLX-IPI

Service Parts Diagram

Beginning Manufacturing Date: May 2006

Ending Manufacturing Date: ______

Log Set Assembly

Part number list on following page.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0868

Page 69

Service Parts List

IMPORT ANT: THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Assembly, NG LOGS-6000GLX Y Log Assembly , LP LOGS-6000GLXLP Y Log #1 Flame Out of Log Left, NG SRV2101-085

Log #1 Flame Out of Log Left, LP SRV2101-087 Log #2 Flame Out of Log Right, NG SRV2101-086

Log #2 Flame Out of Log Right, LP SRV2101-088 3 Log #3 SRV2101-197 4 Log #4 SRV386-716 5 Log #5 SRV2101-195 6 Log #6 SRV2101-196 7 Log #7 SRV530-703

Refractory Red (-R) 4 pieces Red BRICK-6GLX-R

Refractory Stratford Tan (-S) 4 pieces Stratford BRICK-6GLX-S

Right Refractory (-R) SRV2101-572 8

Right Refractory (-S) SRV2101-472

Back Refractory (-R) SRV2101-570 9

Back Refractory (-S) SRV2101-470

12 Grate Assembly 2101-043 13 Non-combustible board 2101-312 14 Surround 2101-260 15 Glass Assembly GLA-6GLX Y

16 17 Junction box 4021-013 Y

Additional service part numbers on following page.

Top Refractory (-R) SRV2101-573

Top Refractory (-S) SRV2101-473

Left Refractory (-R) SRV2101-571

Left Refractory (-S) SRV2101-471

Burner Assembly Red (-R) SRV2101-008 Y

Burner Assembly Stratford Tan (-S) SRV2101-007 Y

Blower GFK-160A

Flue Restrictor 385-128

Gasket Assembly

Contains: Vent, Seal Cap, Burner Neck, Shutter

Bracket, Manifold, and Valve Plate Gaskets Glass Latch Assembly 386-122A Y Mineral Wool 050-721 Touch Up Paint TUP-GBK-12 Vermiculite Embers MYSTIC-EMBERS Wall Switch Kit WSK300-HNG

2103-081

6000GLX-IPI

Stocked

at Depot

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 69

Page 70

Service Parts

6000GLX-IPI-R,-S

Valve Assembly Diagram/ Parts List

Intermittent Pilot Ignition

Valve Assembly

Beginning Manufacturing Date: May 2006

Ending Manufacturing Date: ______

Part number list on following page.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0870

Page 71

Service Parts List 6000GLX-IPI-R,S

IMPORTANT: THIS IS DATED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Pilot Assembly , NG 2090-012

Pilot Assembly , LP 2090-013

2 Shutter Sleeve 2026-130 3 Shutter Bracket Assembly 2026-017 4 Valve Bracket 2118-104 5 Flex Ball Valve Assembly 302-320A 6 Ember Bulb 20W 2088-136 7 Bulb/ Socket Assembly 2101-041

Valve, NG 750-500

Valve, LP 750-501 Oriﬁ ce, NG #39C 582-839

Oriﬁ ce, LP #54C 582-854

10 Control Module 593-592

11 Flex 12 2101-293 12 Wire Assembly 593-590A 13 Manifold Assembly , Solenoid 2101-071

14 15 Solenoid Capacitor Assembly 2101-072

16 12V Transformer 2101-290 17 Wall Switch Wire 2095-550 18 Bracket, Bulb box 2101-120 19 Bulb Bracket Glass 2101-164 20 Kapton Lens 2101-252 21 Glass Bracket 2101-132

Oriﬁ ce, NG #53C Qty 2 req 582-853 Oriﬁ ce, LP #68C Qty 2 req 582-868

Stocked

at Depot

Y Y Y Y

Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y



Battery Pack 593-594A Cord Assembly 2101-084

Conversion Kit NG NGK-6GLX-IPI Conversion KIT LP LPK-6GLX-IPI

Pilot Oriﬁ ce, NG 593-528 Pilot Oriﬁ ce, LP 593-527 Regulator, NG NGK-DXV Regulator, LP LPK-DXV

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08 71

Y Y

Y Y Y Y Y Y

Page 72

D. Contact Information



Heat & Glo, a brand of Hearth & Home Technologies Inc.

7571 215th Street West, Lakeville, MN 55044

www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns.

For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/0872

Hearth and Home Technologies 6000GLX-IPILP-R, 6000GLX-IPI-S, 6000GLX-IPI-R, 6000GLX-IPILP-S User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual