Hearth and Home Technologies 43M-ACC-MBK, 43ST-ACC User Manual

Download

Page 1

DO NOT

DISCARD

Advanced Combustion Control (ACC)

O- T L

Tested and

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

Step Top Uni-Body Model

(Pedestal Model Shown)

•

Important operating and maintenance instructions included.

4300 WOOD STOVE SERIES

Owner’s Manual

Installation and Operation

Models:

43M-ACC-MBK

43ST-ACC

Millennium Model

CAUTION

DO NOT DISCARD THIS MANUAL

•

Read, understand and follow these instructions for safe installation and operation.

Leave this manual with

• party responsible for use and operation.

WARNING

If the information in these instruc-

tions is not followed exactly, a re

may result causing property damage, personal injury, or death.

Do not store or use gasoline or other am-

• mable vapors and liquids in the vicinity of this or any other appliance.

• Do not overre - If heater or chimney con nector glows, you are overring. Overring will void your warranty.

• Comply with all minimum clearances to combustibles as specied. Failure to comply may cause house re.

Installation and service of this appliance should be performed by qualied personnel. Hearth & Home Technologies recommends NFI certied professionals, or technicians supervised by an NFI certied professional.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as replace.

• Al ert children and adults to hazar ds of high temperatures.

High temperatures may ignite clothing or other

ammable materials.

• Keep clothing, furniture, draperies and other ammable materials away.

WARNING

Fire Risk.

For use with solid wood fuel only. Other fuels may overre and generate

poisonous gases (i.e. carbon monoxide).

www.quadrare.com

7037-135E

September 1, 2008

Page 2

4300 Wood Stove Series (ACC)

and Welcome to the Quadra-Fire Family!

INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH

MINIMUM

2 FOOT VERTICAL OFF STOVE TOP

INSTALLATION: ENTIÈREMENT VERTICALE OU HORIZONTALE AVEC 609mm VERTICAL

MINIMUM

DU HAUT DU POÊLE

SINGLE WALL PIPE A B C D E F G H

Flat Top Model 18 (457) 15.5 (394) 26 (660) 17 (432) 10 (255) 18.5 (470) 52.5 (1334) 18 (457)*

Step Top Model 12 (305) 8.5 (216) 23 (584) 13 (330) 2 (51) 13 (330) 50.5 (1283) 18 (457)* DOUBLE WALL PIPE Flat Top Model 13 (330) 10.5 (267) 24.5 (622) 15 (381) 10 (255) 18.5 (470) 52.5 (1334) 10 (254)

Step Top Model 10 (254) 6.5 (165) 23 (584) 13 (330) 2 (51) 13 (330) 50.5 (1283) 5 (127) INSTALLATION: 90o ELBOW OFF TOP OF STOVE THROUGH BACKWALL

INSTALLATION: 90oDU COURBURE AU DESSUS DE HAUT DU POÊLE A TRAVERS LE MUR ARRIÈRE DOUBLE WALL PIPE Flat Top Model 8.5 (216) 6 (152) 24.5 (622) 15 (381) 10 (254) 18.5 (470) 52.5 (1334) 18 (457)* Step Top Model 7.5 (191) 4 (102) 19 (483) 9 (229) 2 (51) 13 (330) 50.5 (1283) 18 (457)*

INSTALLATION: ALCOVE -

Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL103 HT* listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a minimum height of 45.5 inches (1156mm) to top of unit, and the referenced clearances. Please refer to the clearances below for minimum Alcove height requirement to top of unit.

INSTALLATION: ALCÔVE - De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT de Classe "A", ou une cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de l'alcôve ne doit pas être de plus de 48 inches (1220mm) avec une hauteur minimum de 45.5 inches (1156mm) du haut de l'appareil, et des espaces libres alloués. Référez vous s'il vous plaît aux dégagements repirs ci-dessus pour la hauteru minimum requise entre le dessus ole l'appareil et l'alcove (de la chimineé).

DOUBLE WALL PIPE

Flat Top Model 13 (330) 10.5 (267) 24.5 (622) 15 (381) N/A N/A 52.5 (1334) N/A

Step Top Model

10 (254) 6.5 (165) 23 (584) 13 (330) N/A N/A 37 (940) N/A

*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650oC Factory-built chimney. *Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650oC cheminée bâtit en usine.

NFPA 211

MINIMUM

CLEARANCES - NOT TESTED

SPÉCIFICATIONS DE LA VENTILATION:

MUR SIMPLE: De six (6 inches) (152mm) de diamètre le connecteur de conduit de minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides, ou une cheminée de briques, avec espaces libres référés. MUR DOUBLE: De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT* de Classe "A:, ou une cheminée de briques, avec espaces libres alloués. MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk Metalbestos DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les espaces libres pour mur double comme mentionné ci-bas.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: In Inches & (Millimeters)

NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar.

LISTED ROOM HEATER, SOLID FUEL TYPE. ALSO FOR USE IN MOBILE HOMES. (UM) 84 HUD

1445 N. Highway, Colville, WA 99114

www.quadrafire.com

Install and use only in accor dance with

manufacturer 's instal lation an d operati ng instructions. C ontact loca l building or fire officials about res trictions and installa tion inspections in your area. Do not obstruct the space beneath heater. WARNING - For Mobile Homes: Do not install in a sleeping room. An outside combustion air inlet must be provided and unrestricted while unit is in use. The structural integrity of the mobile home floor, ceiling and walls must be maintained. The stove needs to be properly grounded to the frame of the mobile home. Components required for mobile home installation: Outside Air Kit, Part Number OAK-ACC. Refer to manufactur er's instruct ions and local codes for precautions required for passing chimney through a combustible wall or ceiling and maximum offsets. I

nspect and clean chimney freq uently - Under Certain Conditions of Use, Creosote Buildup May Occur Rapidly. Do not connect this unit to a chimney serving another appliance. Optional Components: Op tional Blower, Part BK-ACC. Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz. Route power cord away from unit. Do not route cord under or in front of appliance. DANGER: Risk of electrical shock. Disconnect power supply before servicing. Replace glass only with 5mm ceramic available from your dealer. Do not use grate or elevate fire. Build wood fire directly on hearth. Do not overfi re - if heat er or chimney

connector glows, you are overfiring. Operate o nly with th e fuel load ing door closed. Open only to add fuel to the fire.

CAUTION

U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to

comply with July 1990 particulate emission standards.

2008 2009 2010 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.

PREVENT HOUSE FIRES

FLOOR PROTECTION:

Floor protector must be a 3/8 inch min. thickness, non-combustible material or equivalent, extending beneath heater and to front/sides/rear as indicated on the diagram below. Exception: Non-combustible floor protections must extend beneath the flue pipe when installed with horizontal venting and extend 2 inches (51mm) beyond each side.

O-T L

Tested and Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

Report / Rapport #061-S-67-7

TESTED TO:/ TESTÉ À: UL 1482, ULC S627-00

HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS.

VENT SPECIFICATIONS:

SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney, suitable for use with solid fuels, or a masonry chimney, and the referenced clearances. DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or a masonry chimney and the referenced clearances MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or Security DL double wall connector pipe. Must be equipped with a spark arrestor. Apply double wall clearances below when installing unit.

SERIAL NO. /NUMÉRO DE SÉRIE

4300 ACC Series

7037-136

CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.

ATTENTION:

APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE COMBUSTIBLE SOLIDE, POUR USAGE DANS LES MAISONS MOBILES. ( UM) 84 HUD. "Pour Usage

Avec Bois Solide Seulement"

Installez et utilis ez en acc ord av ec le s ins tructions d'installatio n et d'opér ation du f abricant. Cont actez le bureau de la construction ou le bureau des incendies au sujet des restrictions et des inspections d'installation dans votre voisinage. Ne pas obstruez l'espace en dessous de l'appareil. AVIS - Pour Les Maisons Mobiles: Ne pas installer dans une chambre à coucher. Un tuyau extérieur de combustion d'air doit être installé et ne doit pas être obstrué lorsque l'appareil est en usage. La structure intégrale du plancher, du plafond et des murs de la maison mobi le doit être maintenue intacte. L'appareil de chauffage doit être fixé à la charpente de la maison mobile. Les composants requis pour l'installation des maisons mobiles: Assemblage d'air extérieur, Numéro de Pièce OAK-ACC.. Référez vous aux instructions du fabricant et des codes locaux pour les p récautions requises pour passer une cheminée à travers un mur ou un plafond combustibles, et les compensations maximums. In

spectez et nettoy ez la cheminée fréquemment. Sous certaines conditions, il se peut que la créosote s'accumule rapidement. Ne pas connecter cet appareil à une cheminée servant un autre appareil. Composants Optio nnels: Ventilateur Optionn el, P ièce BK-ACC. Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz. Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil. DANGER: Il y a risque de dé charge électriqu e. Déconnectez le fil électrique de la prise de contact avant le service. Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseur. N'élevez pas le feu. Bâtissez le feu de bois directement sur l'âtre. Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau de cheminée rougissent, vous surchauffez. Opérez l'ap pareil seuleme nt l orsque la port e d e chargement est fermée. Ouvrez la porte seulement lorsque vous devez ajouter des combustibles dans le feu.

PRÉVENTION DES FEUX DE MAISON

PROTECTION DU PLANCHER:

Le protecteur de plancher doit être d'un minimum de 3/8 inch d'épaisseur, de matériel incombustible ou équivalent, s'étendant du dessous de l'app areil de chauffage à l'avant, aux cotés et à l'arrière comm e indiqué sur le diagramme suivant. Exception: Les protections incombustibles du plancher doivent s'étendre en dessous du conduit de cheminée lorsqu'in stallées avec une ventilation à l'horizontale et s'étendre de 2 inches (51mm) de chaque côté.

ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:En Pouces & (millimètres)

NOTE: Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de l'entrée du conduit.

BACKWALL/SIDEWALL

MUR ARRIÈRE/MUR DE CÔTÉ

CORNER INSTALLATION/ INSTALLATION DU COIN

ALCOVE TOP VIEW /

VUE DU HAUT DE L'ALCÔVE

ALCOVE SIDE VIEW /

VUE DE CÔTÉ DE L'ALCÔVE

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE

Made in U.S.A./Fait Aux États-Unis

Manufactured by: Fabriqué par:

90o OFF TOP UP & OUT CEILING CLEARANCE ESPACE LIBRE DU DESSUS DE L'APPAREIL AU PLAFOND AVEC 90 DE COURBURE

STOVE TO CEILING CLEARANCE ESPACE LIBRE DU POÊLE AU

PLAFOND

16" from glass

USA

Fuel loading door

4-1/2"

3-1/2"

31-5/8" minimum

40-7/16" minimum

CANADA

203mm (8")

203mm

(8")

203mm

(8")

457mm (18")

1281mm (50-7/16") minimum

1080mm (42-1/2")

minimum

CONDUIT DU MUR SIMPLE

Modèle au dessus en appartement Modèle au dessus en escalier

CONDUIT DU MUR DOUBLE

Modèle au dessus en appartement Modèle au dessus en escalier

CONDUIT DU MUR DOUBLE

Modèle au dessus en appartement Modèle au dessus en escalier

CONDUIT DU MUR DOUBLE

Modèle au dessus en escalier

Modèle au dessus en appartement

007003

Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality, durability, and performance.

This commitment begins with our research of the market, including ‘Voice of the Customer’ contacts, ensuring we make products that will satisfy your needs. Our Research and Development facility then employs the world’s most advanced technology to achieve the optimum operation of

SAMPLE OF SERIAL NUMBER / SAFETY LABEL

LOCATION: BACK OF APPLIANCE

our stoves, inserts and replaces. And yet we are old-fashioned when it comes to craftsmanship. Each unit is meticulously fabricated and surfaces are hand-nished for lasting beauty and enjoyment. Our pledge to quality is completed as each model undergoes a quality control inspection.

We wish you and your family many years of enjoyment in the warmth and comfort of your hearth appliance. Thank you for choosing Quadra-Fire.

Page 2

SAMPLE

7037-135E

Serial No.

Model Name

Test Lab & Report No.

Mfg. Date

September 1, 2008

Page 3

TABLE OF CONTENTS

4300 Wood Stove Series (ACC)

Section 1: Listing and Code Approvals

A. Appliance Certications ......................4

B. Mobile Home Approved ......................4

C. Glass Specications ............................4

D. BTU & Efciency Specications ..........4

Section 2: Getting Started

A. Design, Installation & Location

Considerations ....................................5

B. Fire Safety ..........................................5

C. Negative Pressure ..............................6

D. Flue Draft Considerations ................... 7

E. Venting Systems .................................7

F. Tools and Supplies Needed................7

G. Inspect Appliance & Components....... 7

H. Typical Stove System .........................8

Section 3: Dimensions & Clearances

A. Appliance Dimensions ........................9-10

B. Clearances to Combustibles ............... 11

Section 4: Installation Consideration

A. Hearth Requirements .........................12-1

B. Outside Air Kit Installation ...................14

C. Blower Installation ...............................15

Section 8: Operating Instructions (Cont’d)

H. Correct Bafe & Blanket Placement .... 29

I. Blower Operating Instructions ............. 29

J. Opacity (Smoke) .................................29

K. Frequently Asked Questions ...............30

Section 9: Maintaining & Servicing Appliance

A. General Maintenance & Cleaning ....... 1-2

B. Glass Replacement .............................33

C. Firebrick Replacement ........................4

D. Bafe Removal ....................................35

E. Snap Disc Replacement .....................35

F. Tube Channel Replacement ...............36

Section 10: Troubleshooting ........................37

Section 11: Reference Material

A. Exploded Drawings ............................. 8-40

B. Service Parts & Accessories...............41-43

C. Service & Maintenance Log ................ 44

D. Homeowner’s Notes ...........................45

E. Warranty Policy ................................... 46-47

F. Contact Information ............................. 48

Section 5: Chimney Requirements

A. Venting Components ..........................16

B. Chimney Systems ...............................16-18

C. Installing Chimney Components .........18

D. Chimney Termination Requirements ..19

E. 2-10-0 Rule ........................................19

Section 6: Mobile Home ...............................20

Section 7: Appliance Set-Up A. Pedestal & Ash Removal System

(ARS) Installation ...............................21-22

B. Leg Kit & Ash Removal System

(ARS) Installation...........................2

C. Door Handle Assembly .......................24

D. Blower Speed Adjustment ..................24

Section 8: Operating Instructions

A. Over-Firing Your Appliance .................25

B. Wood Selection & Storage ..................25

C. Burning Process ..................................25-26

E. Air Controls .........................................26-27

F. Burn Rates & Operating Efciency .....27

G. Building A Fire .....................................28

Automatic Combustion Control (ACC)

....26

September 1, 2008

7037-135E

Page 

Page 4

4300 Wood Stove Series (ACC)

Listing and Code Approvals

A. Appliance Certication

Model:

Laboratory: OMNI Test Laboratories, Inc. Report No & Date: Type: Standard: UL1482 and ULC S627-00 and

The Quadra-Fire 400 Series Wood Stove (ACC) meets the U.S. Environmental Protection Agency’s 1990 particulate emission standards.

400 Millennium & Step Top (ACC) Uni-Body

061-S-67-6

Listed Room Heater, Solid Fuel Type

(UM) 84-HUD, Mobile Home Approved.

B. Mobile Home Approved

This appliance is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided. The structural integrity of the mobile home oor, ceiling, and walls must be maintained. The appliance must be properly grounded to the frame of the mobile home and use only listed double-wall connector pipe. Outside Air Kit, part OAK-ACC must be installed in a mobile home installation

D. BTU & Efciency Specications

EPA Certied:

EPA Certicate Number

and Date:

Efciency:

BTU Output: Heating Capacity:

Vent Size: Firebox Size: Max Wood Length: Fuel: Shipping Weight:

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products, their specications and/or price without notice.

1.1 grams per hour

Number: 656 Issued: 02-05-2007

79.82%

11,800 to 8,00 / hr.

1,500-2,400 sq ft depending on climate zone

6 inches

2.4 cubic feet

20 inches

Cord Wood

55 lbs

C. Glass Specications

This stove is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the UL1482, (UM)

84-HUD and NPFA211 in the U.S.A. and the ULC S627-00 and CAN/CSA-B365 Installation Codes in Canada.

Page 4

7037-135E

September 1, 2008

Page 5

4300 Wood Stove Series (ACC)

. Design, Installation & Location Considerations

Consideration must be given to:

• Safety

• Convenience

• Trafc ow

• Chimney and chimney connector required

It is a good idea to plan your installation on paper, using exact measurements for clearances and oor protection, before actually beginning the installation. If you are not using an existing chimney, place the appliance where there will be a clear passage for a factory-built listed chimney through the ceiling and roof.

We recommend that a qualied building inspector and your insurance company representative review your plans before and after installation

If this appliance is in an area where children may be near it is recommended that you purchase a decorative barrier to go in front of the appliance. away while it is operating and do not let anyone operate this appliance unless they are familiar with these operating instructions.

NOTE: Service Space:

In order to replace the tube channel a clearance of 19 inches (48mm) is required on the right side of stove in order to remove the tubes with the stove in place.

If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement. See page 36.

Getting Started

Remember to always keep children

CAUTION

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and national codes and regulations.

• Consult insurance carrier, local building, re ofcials or authorities having jurisdiction about restrictions, installation inspection, and permits.

B. Fire Safety

To provide reasonable re safety, the following should be given serious consideration:

1. Install at least one smoke detector on each oor of your home to ensure your safety. They should be located away from the heating appliance and close to the sleeping areas. Follow the smoke detector manufacturer’s placement and installation instructions, and be sure to maintain regularly.

2. A conveniently located Class A fire extinguisher to contend with small fires resulting from burning embers.

. A practiced evacuation plan, consisting of at least two

escape routes.

4. A plan to deal with a chimney re as follows:

In the event of a chimney re:

a. Evacuate the house immediately b. Notify re department

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance.

• Modication of the appliance.

• Installation other than as instructed by Hearth & Home Technologies.

• Installation and/or use of any component part not approved by Hearth & Home Technologies.

• Op era ting appli anc e with o ut ful ly ass emb ling al l components.

• Operating appliance without legs attached (if supplied with unit).

• Do NOT Overre - If appliance or chimney connector glows, you are overring.

Any such action that may cause a re hazard.

Asphyxiation Risk.

• Do NOT connect this unit to a chimney ue servicing another appliance.

• Do NOT connect to any air distribution duct or system.

May allow ue gases to enter the house.

September 1, 2008

WARNING

7037-135E

WARNING

Fire Risk.

• Do not operate appliance before reading and understanding operating instructions.

• Failure to operate appliance properly may cause a house re.

Page 5

Page 6

4300 Wood Stove Series (ACC)

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended: Outside Air Intake on windward side

NOT recommended: Outside Air Intake on leeward side

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

C. Negative Pressure

Draft is the pressure difference needed to vent appliances successfully. Considerations for successful draft include:

• Preventing negative pressure

• Location of appliance and chimney

Negative pressure results from the imbalance of air available for the stove to operate properly. Causes for this imbalance include:

• Exhaust fans (kitchen, bath) etc.)

• Range hoods

• Combustion air requirements for furnaces, water heaters and other combustion appliances

• Clothes dryers

• Location of return-air vents to furnace or air conditioning

• Imbalances of HVAC air handling system

• Upper level air leaks

• Recessed lighting

• Attic hatch opening

• Duct leaks

To minimize the affects of negative air pressure the following must be considered:

• Install the outside air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

• Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the appliance,

• Avoid installing the appliance near doors, walkways or small isolated spaces.

• Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted duckwork and air handler joints and seams taped or sealed.

WARNING

Asphyxiation Risk.

• Negative pressure can cause spillage of combustion fumes, soot and carbon monoxide.

• Appliance needs to draft properly for safety.

Figure 6.1

Page 6

7037-135E

September 1, 2008

Page 7

4300 Wood Stove Series (ACC)

D. Flue Draft Considerations

Location of the appliance and chimney will affect performance. As shown in Figure 6.1 on page 6 the chimney should:

• Be installed through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die down of the re.

• Penetrate the highest part of the roof. This minimizes the affects of wind turbulence and down drafts.

• Consider the appliance location in order to avoid oor and ceiling attic joists and rafters.

Exterior conditions such as roof line, surrounding trees, prevailing winds and nearby hills can influence stove performance. Your local dealer is the expert in your geographic area and can usually make suggestions or discover solutions that will easily correct your ue problem.

o be sure that your appliance burns properly, the chimney draft (static pressure) should be approximately -.04 inch water column (W.C.) during a low burn and -.10 inch W.C. during a high burn, measured 6 inches (152mm) above the top of the appliance after one hour of operation at each burn setting.

NOTE: These are guidelines only, and may vary somewhat for individual installations.

E. Venting Systems

The venting system consists of a chimney connector (also known as stove pipe) and a chimney. These get extremely hot during use. Temperatures inside the chimney may exceed 2000°F (1100°C) in the event of a creosote re. To protect against the possibility of a house re, the chimney connector and chimney must be properly installed and maintained. An approved thimble must be used when a connection is made through a combustible wall to a chimney.

A chimney support package must be used when a connection is made through the ceiling to a prefabricated chimney. These accessories are absolutely necessary to provide safe clearances to combustible wall and ceiling material. Follow venting manufacturer’s clearances when installing venting system.

F. Tools And Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw Pliers Hammer Phillips Head Screwdriver Flat Blade Screwdriver Plumb Line Level Tape Measure

Framing Material Hi-Temp Caulking Material Gloves Framing Square Electric Drill & Bits (1/4”) Safety Glasses 1/2 in. - /4 in. length, #6 or #8 self drilling screws (need  per pipe section connection)

G. Inspect Appliance & Components and

Pre-Use Check List

1. Place the appliance in a location near the nal installation area and follow the procedures below:

2. Open the appliance and remove all the parts and articles packed inside the Component Pack. Inspect all the parts and glass for shipping damage. Contact your dealer if any irregularities are noticed.

3. All safety warnings have been read and followed.

4. This Owner’s Manual has been read.

5. Floor protection requirements have been met.

6. Venting is properly installed.

7. The proper clearances from the appliance and chim-

ney to combustible materials have been met.

8. The masonry chimney is inspected by a professional and is clean, or the factory built metal chimney is installed according to the manufacturer’s instructions and clearances.

9. The chimney meets the required minimum height.

10.

11. Plated surfaces have been wiped clean, if appli-

12. A power outlet is available nearby if installing

All labels have been removed from the glass door.

cable.

optional blower assembly.

Asphyxiation Risk.

• Do NOT connect this unit to a chimney ue servicing another appliance.

• Do NOT connect to any air distributon duct or system.

May allow ue gases to enter the house.

September 1, 2008

WARNING

7037-135E

WARNING

Fire Risk.

Inspect appliance and components for damage. Damaged parts may impair safe operation.

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Page 7

Page 8

4300 Wood Stove Series (ACC)

Floor Protector

Chimney Connector

Insulated " T "

Flashing

Listed Termination Cap

Trim Collar on Inside Wall

Listed Chimney

Storm Collar

Wall Support

Roof Brace (if required)

Thimble

Floor Protector

Thimble, 12" (305mm) Of Brick

Ceiling Joist

Combustible Wall

Airtight Cleanout Door

Fireclay Flue Liner With Air Space

Sheathing

Eave

1" (25mm) Clearance With Firestop

Rafter

Flashing

Concrete Cap

Outside Air Termination Cap

Outside Air Rear Vent

Spark Arrestor Cap

Floor Protector

Chimney Connector

Ceiling Support

Listed Chimney

Listed Termination Cap

Storm Collar

Flashing

H. Typical Stove Systems

Stove system with masonry chimney consists of:

• Stove

• Chimney Connector (stove pipe)

• Thimble

• Masonry Chimney

• Hearth Pad Floor Protection

Stove system with prefabricated metal chimney consists of:

• Stove

Chimney Connector

• (stove pipe)

• Thimble (for exterior chimney)

• Firestops

• Insulations Shields

• Storm Collar and Flashing

• Termination Cap

• Hearth Pad Floor Protection

Figure 8.1 Masonry Chimney

Page 8

7037-135E

Figure 8.3 Interior Prefabricated ChimneyFigure 8.2 Exterior Prefabricated Chimney

September 1, 2008

Page 9

Dimensions and Clearances

28-7/16 in.(722mm)

26-5/16 in. (668mm)

15-5/8 in. (397mm)

11-1/2 in. (292mm)

16 in. (406mm)

20-3/4 in. (527mm)

4-1/2 in

(108mm)

Outside Air

Connection

14-15/16 in. (7mm)

25 in. (65mm)

9-15/16 in. (27mm)

12-1/2 in. (18mm)

0 in. (762mm)

15-1/16 in. (8mm)

10-15/16 in. (271mm)

18-15/16 in. (475mm)

A. Appliance Dimensions

NOTE: Flue Collar size is 6 inch (152mm) diameter (ID)

Millennium Model

4300 Wood Stove Series (ACC)

Figure 9.1 Front View

September 1, 2008

Figure 9.2 Side View

7037-135E

Page 9

Page 10

4300 Wood Stove Series (ACC)

2-7/8 in. (606mm)

-7/16 in.

(849mm)

15-1/16 in.

(8mm)

19-1/16 in.

(484mm)

10-15/16 in.

(278mm)

14-15/16 in.

(79mm)

3-11/16 in. (94mm)

2-1/8 in. (587mm)

10-/8 in. (264mm)

Back of Stove to Glass

25-/8 in. (645mm)

6-11/16 in. (170mm)

-1/2 in. (89mm)

4-/4 in. (88mm)

26 in. (660mm)

1 in.

(0mm)

9-/16 in. (2mm)

18 in.

(457mm)

28-7/16 in.(722mm)

26-5/16 in. (668mm)

15-5/8 in. (97mm)

11-1/2 in.

(292mm)

16 in. (406mm)

20-/4 in. (527mm)

Appliance Dimensions (Cont’d)

4300 Step Top Pedestal Model

4300 Step Top Leg Model

Figure 10.1

Figure 10.3

Figure 10.2

Page 10

7037-135E

Figure 10.4

September 1, 2008

Page 11

B. Clearances to Combustibles (UL and ULC)

BACKWALL / SIDEWALL

CORNER INSTALLATION

90° OFF TOP UP & OUT CEILING CLEARANCE

STOVE TO CEILING CLEARANCE

ALCOVE TOP VIEW

ALCOVE SIDE VIEW

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)

NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.

A B C D E F G H

INSTALLATION: Full Vertical OR Horizontal with Minimum 2 FT Vertical Off Stove Top

SINGLE WALL PIPE

Flat Top Model 15.5 (394) 11.75 (298) 24.5 (622) 14.5 (368) 10 (254) 17.5 (445) 53.5 (1359) 12 (305) Step-Top Model 15.5 (394) 11.75 (298) 24.5 (622) 14.5 (368) 2 (51) 12 (305) 49.5 (1283) 12 (305)

DOUBLE WALL PIPE Flat Top Model 9 (229) 5.25 (133) 24.5 (622) 14.5 (368) 10 (254) 17.5 (445) 53.5 (1359) 12 (305) Step-Top Model 7.5 (191) 3.75 (95) 22 (559) 11.75 (298) 2 (51) 12 (305) 49.5 (1283) 5 (127)

INSTALLATION: 90° Elbow Off Top of Stove Through Backwall

DOUBLE WALL PIPE

Flat Top Model 8.5 (216) 6 (152) 24.5 (622) 15 (381) 10 (254) 17.5 (445) 53.5(1359) N/A Step-Top Model 7.5 (191) 4 (102) 19 (229) 9 (229) 2 (51) 12 (305) 49.5 (1283) N/A

INSTALLATION: ALCOVE

Six inch (6") (152mm) diameter listed Double Wall air insulated connector pipe with UL103 HT* listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor). Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a minimum height of 49.5 inches (1283mm) to top of unit, and the referenced clearances.

*In Canada must comply with CAN/ULC-S269 M87 for the 650oC Factory-built chimney.

DOUBLE WALL PIPE

Flat Top Model 13 (330) 10 (254) 24.5 (622) 14.5 (368) N/A N/A 53.5 (1359) 12 (305) Step-Top Model 7.5 (191) 3.75 (95) 22 (584) 11.75 (298) N/A N/A 49.5 (1257) 5 (127)

NOTE: Clearances may only be reduced by means approved by the regulatory authority having jurisdiction

4300 Wood Stove Series (ACC)

September 1, 2008

Fire Risk.

• Comply with all minimum clearances to

• Failure to comply may cause house re.

WARNING

combustibles as specied.

7037-135E

NOTE: Service Space

In order to replace the tube channel assembly a clearance of 19 inches (48mm) is required on the right side of stove in order to remove the tubes with the stove in place.

If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement. See Figure 36 on page 36.

Page 11

Page 12

4300 Wood Stove Series (ACC)

16" from glass

8 in.

Fuel loading door

4-7/8 in.

3-1/8 in."

31-5/8 in. minimum

41-3/8 in. minimum

1-5/8 in.

27-/8 in.

7 in.

40-15/16 in.

-1/16 in.

135°

51-1/16 in.

Must extend 2 in. (51mm) beyond

each side of pipe (shaded area)

20mm (8 in.)

20mm

(8 in.)

20mm

(8 in.)

457mm (18 in.)

105mm (51-/8 in.) minimum

1041mm (41 in.)

minimum

WARNING

Fire Risk.

• Hearth pads must be installed exactly as specified.

High temperatures or hot embers may ignite concealed combustibles.

Installation

A. Hearth Protection Requirements

FLOOR PROTECTION: Floor protector must be non-com-

bustible material, extending beneath heater and to the front, sides and rear as indicated. The oor must be non-combustible or otherwise adequately protected from radiant heat given off by the unit and from sparks and falling embers. A layer of thin brick or ceramic tile over a combustible oor is not sufcient.

For US installations, i of a minimum of /8 inch (9.5mm) thick metal clad millboard or equivalent a minimum of 16 glass and 8 inches (20mm) to both sides of the fuel loading door. Open the door and measure 8 inches (20mm) from the side edge of the opening in the face of the appliance.

*See exception.

t is necessary to install a oor protector

inches (406mm) in front of

Millennium Model

In Canada, similar oor protection must be provided 18

inches (457mm) in front and 8 inches (20mm) from the sides and rear of the stove. *See exception.

*EXCEPTION: Non-combustible oor protections must extend beneath the ue pipe when installed with horizontal venting and extend 2 inches (51mm) beyond each side.

See Figure 12.4.

Figure 12.1

Page 12

Figure 12.2

USA

CANADA

7037-135E

USA

Figure 12.3

USA required

Canada recommended

Figure 12.4

September 1, 2008

Page 13

Must extend 2 in. (51mm) beyond

each side of pipe (shaded area)

16 in. from glass

8 in.

Fuel loading door

4-3/4 in.

3-1/4 in.

1-5/8 in. minimum

41-/8 in. minimum

20mm (8 in.)

20mm

(8 in.)

20mm

(8 in.)

457mm (18 in.)

105mm (51-/8 in.) minimum

1066mm (42 in.)

minimum

Step-Top Uni-Body Model

48-5/16 in.

1-5/8 in.

40-15/16 in.

27-5/16 in.

 in.

29 in.

135°

4300 Wood Stove Series (ACC)

Figure 13.1

USA

Figure 13.3

USA required

Canada recommended

Figure 13.2

September 1, 2008

NOTE:

• Illustrations and photos reect typical installations and are FOR DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual design preference

• Hearth & Home Technologies reserves the right to alter its products.

CANADA

7037-135E

Figure 13.4

Page 1

Page 14

4300 Wood Stove Series (ACC)

Flex Line

Wire Tie

Flex Adapter

Termination Cap

Remove circular “knock-out” in base of pedestal.

Cover Plate

Rope to Seal Pedestal

B. Outside Air Kit Installation

A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed by the re must be replaced. Air is replaced via air leakage around windows and under doors. In homes that have tightly sealed doors and windows, an outside air source is needed. An optional Outside Air Kit is avail

Included in OAK-ACC: Termination cap, (2) wire ties, flex

adapter, and fasteners

Included in SRV7033-041: Cover plate and sealing rope (see

Floor Installation Alternative below,

Figure 14.2)

Items Needed for Installation (not supplied)

• 4 inch ex aluminum pipe, or if using alternate material, then it shall be made from durable, non-combustible, heat resistant material up to 50oF. Cut the pipe to the required length for your installation.

• Phillips head screw driver

• Silicone sealant

• Drills and saws necessary for cutting holes through the wall or ooring in your home.

able.

WARNING

Fire Risk. Asphyxiation Risk.

Do not draw outside combustion air from:

• Wall, oor or ceiling cavity

• Enclosed space such as an attic or garage

• Close proximity to exhaust vents or chimneys

Fumes or odor may result

WARNING

Asphyxiation Risk.

Outside air inlet must be located to prevent blockage from:

• Leaves

• Snow or ice

• Other debris Block may cause combustion air starvation

Smoke spillage may set off alarms or irritate sensitive individuals.

1. Remove all materials from packing box.

2. Using a #2 Phillips screw driver attach the ex adapter

to the stove using 4 screws. Figure 14.1.

.

Remove circular” knock-out” in the base of the pedestal.

4. Floor & Rear Installation: Cut a 4 inch (102mm)

hole in outside wall or oor to accommodate outside air piping. Use 4 inch (102mm) aluminum metal ex or rigid piping to directly connect outside air to appliance intake. Use the supplied termination cap with a rodent screen. Seal between the wall (or oor) and the pipe with silicone to prevent moisture penetration.

WARNING

Asphyxiation Risk.

Length of outside air supply duct shall NOT exceed the length of the vertical height of the exhaust ue.

•

Fire will not burn properly

• Smoke spillage occurs when door is opened due

to air starvation.

5. Floor Installation Alternative: In some instances you may not be able to install the ex pipe as show in Figure

14.1. If that is the case, you will need to order SRV70041 which includes a cover plate and sealing rope as shown in Figure 14.2. The goal is to seal the pedestal so no room air can leak into the pedestal.

Figure 14.1 - Floor & Rear Installation

Page 14

7037-135E

Figure 14.2 - Floor Installation Alternative

September 1, 2008

Page 15

C. Blower (Optional)

MANUAL: Over-rides the Snap Disc

AUTO: Fan will turn ON/OFF Automatically by the Snap Disc

Controls the Fan Speed

Snap Disc Bracket with Magnet

MANUAL

FAN

AUTO

LOW

HIGH

OFF

Secure wires with wire tie

Do not remove.

4300 Wood Stove Series (ACC)

1. Remove the  bolts (1/4”-20 Phillips head) on the outer skin at the bottom rear of appliance.

2. Align holes in mounting ange of blower with bolt holes in appliance. Blower should be positioned at bottom of rear outer skin as shown in Figure 15.1.

. Re-insert and tighten bolts, securing blower onto outer

wall of appliance.

Place the bracket containing the snap disc and magnet

under the bottom left rear corner as shown in Figure 15.1.

See page 30 for detailed operating instructions for the

blower and snap disc.

CAUTION

Shock Risk.

• Do NOT remove grounding prong from plug.

• Plug directly into properly grounded  prong receptacle.

• Route cord away from appliance.

•

Do NOT route cord under or in front of appliance..

Figure 15.1

September 1, 2008

7037-135E

Page 15

Page 16

4300 Wood Stove Series (ACC)

Floor Protector

Chimney Connector

Insulated " T "

Flashing

Listed Termination Cap

Trim Collar on Inside Wall

Listed Chimney

Storm Collar

Wall Support

Roof Brace (if required)

Thimble

Floor Protector

Chimney Connector

Ceiling Support

Listed Chimney

Listed Termination Cap

Storm Collar

Flashing

Chimney Requirements

A. Venting Components

Chimney Connector:

It is also known as ue pipe or stove pipe. The chimney connector joins the stove to the chimney. It must be a 6 inch (152mm) minimum diameter 24 gauge mild steel black or 26 gauge blued steel, or an approved air-insulated double wall venting pipe.

Thimble:

A manufactured or site-constructed device installed in combustible walls through which the chimney connector passes to the chimney. It is intended to keep the walls from igniting. Site constructed thimbles must meet NFPA 211 Standards. Prefabricated must be suitable for use with selected chimney and meet UL10 Type HT Standards. Follow instructions provided by the manufacturer for manufactured thimbles for masonry chimney and prefabricated chimneys.

Chimney:

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements specied in Section 5B.

B. Chimney Systems

Prefabricated Metal Chimney

• Must be a 6 inch (152mm) diameter (ID) high temperature chimney listed to UL 10 HT (2100oF) or ULC S629M.

• Must use components required by the manufacturer for installation.

• Must maintain clearances required by the manufacturer for installation.

• Refer to manufacturers instructions for installation.

NOTE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100oF) CLASS “A” or conforming to CAN/ULC-S629M, STANDARD FOR 650oC

FACTORY-BUILT CHIMNEYS.

Figure 16.1 Prefabricated Exterior Chimney

Page 16

7037-135E

Figure 16.2 - Prefabricated Interior Chimney

September 1, 2008

Page 17

Thimble

Trim Collar

Chimney Section with 2 in. (51mm)

Clearance to

Combustibles

Chimney

Connector

Fire Clay Flue

Liner

with Airspace

Masonry

Chimney

Wall Band to

Secure Chimney

Section

Wood Studs Used for

Framing - Spaced 2 in.

(51mm) clearance from

Masonry Chimney

Wall Spacer

1.5”

1.0”

2.0”

1.5”

14.0” ID

17.0” OD

ceiling

Minimum18.0”

NFPA 211

13.5” below ceiling to top of opening

1.0”

8.0”

1.5 2x2 framing stud

2.0 min air clearance

1.0 min air clearance

4.5

or top of opening is a min.of

4.5” below min.clearance specified by connector mfg.

Center of Hole

Thimble

Wall

Include depth of hearth pad

Site constructed for masonry chimney installation:

Components

• A minimum length of 12 inches [05mm] (longer for

• Wall spacer, trim collar and wall band to t solid pack

• Minimum 8 inch (20mm) diameter clay liner section (if

Air Clearances

• Masonry chimney clearance must meet NFPA 211 mini-

• Minimum of 1 inch (25mm) clearance around the chim-

• Top of wall opening is a minimum of 1-1/2 inches

Instructions:

1. Open inside wall at proper height for the chimney con-

2. Entry hole to masonry chimney must be lined with an 8

. Construct a 17 inch x 17 inch (42mm x 42mm) out-

4. Attach the wall spacer to the chimney side of the

5. Nail the frame into the wall opening. The spacer should

6. Insert the section of the solid insulated chimney into

7. Tightly secure the length of the solid insulated chimney

8. Insert a section of chimney connector into the chimney.

9. Seal the end of the chimney connector to the clay liner

10.

September 1, 2008

thicker walls) of solid insulated factory-built chimney length constructed to UL 10 Type HT 6 inch (152mm) inside diameter. Chimney needs to extend a minimum of 2 inches (51mm) from the interior wall and a minimum of 1 inch (25mm) from the exterior wall.

chimney selected.

not already present in chimney) and refractory mortar.

mum requirement of 2 inches (51mm) to sheet metal supports and combustibles.

ney connector.

(4mm) from ceiling or 4-1/2 inches (114mm) below minimum clearance specied by chimney connector manufacturer. NFPA 211 minimum vertical clearance of 18 inches (457mm) from chimney connector and ceiling or minimum recommended by chimney connector manufacturer. Figure 17.1.

nector to entry the masonry chimney. Figure 17.1.

inch (20mm) minimum diameter clay liner, or equivalent, secured with refractory mortar.

side dimension frame from 2 x 2 framing lumber to t into wall opening. Inside opening of frame should be no less than 14 inch x 14 inch (56mm x 56mm).

Figure 17.1.

frame.

be on the chimney side.

the outer wall of the masonry chimney.

with the wall band to the masonry chimney.

Make sure it does not protrude past the edge of the clay chimney liner inside the chimney.

with refractory mortar.

Install trim collar around the sold pack chimney section

7037-135E

4300 Wood Stove Series (ACC)

Figure 17.1

Solid Pack Chimney with Metal Supports as a Thimble

Figure 17.2

WARNING

Fire Risk.

Do NOT pack insulation or other combustibles between spacers.

• ALWAYS maintain specied clearances around vent ing and spacers.

• Install spacers as specied.

Failure to keep insulation or other material away from

vent pipe may cause re.

Page 17

Page 18

4300 Wood Stove Series (ACC)

Flue Gas

Direction

Crimped

End

Toward

Stove

Secure pipe sections with a

minimum of  screws

Chimney Flue

Liner

Fireclay

Liner or

Equivalent

Masonry Chimney

Constructed to NFPA 211

Wall Spacer

Wall Band

Trim Collar

Chimney

Connector

1 inch (25mm) Air

Space to Chimney

Section

Min. Clearance

2 inch (51mm)

Min. Chimney Clearance to

Wall Spacer and

Combustibles - 2 inch (51mm)

Chimney Section

Solid Pack Chimney with Metal Supports as a Thimble (Cont’d)

Figure 18.1

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or diameter varies from this conguration, the possibility of performance problems exists.

Chimney height may need to be increased by 2 - % per each 1000 feet above sea level. It is not recommended to use offsets or elbows at altitudes above 4000 feet above sea level or when there are other factors that affect ue draft.

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.

This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the appliance and to each other with the crimped (male) end pointing toward the stove. All joints, including the connection at the ue collar, should be secured with  sheet metal screws. Make sure to follow the minimum clearances to combustibles. Where passage through the wall, or partition of combustible construction is desired in Canada, the installation shall conform to CAN/CSA-B65.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this unit in a mobile home. The listed connectors must conform to each other to ensure a proper t and seal.

Figure 18.2 Chimney Connector (Stove Pipe)

Fire Risk.

Inspection of Chimney:

• Chimney must be in good condition.

• Meets minimum standard of NFPA 211

• Factory-built chimney must be 6 inch

Page 18

Asphyxiation Risk.

WARNING

(152mm) UL10 HT.

WARNING

• Do NOT connect this unit to a chimney ue servicing another appliance.

• Do NOT connect to any air distribution duct or system.

May allow ue gases to enter the house.

7037-135E

WARNING

Fire Risk.

Follow Chimney Connector Manufacturer’s Instructions for Proper Installation.

ONLY use connector:

• Within the room, between appliance and ceiling or wall. Connector shall NOT pass through:

• Attic or roof space

• Closet or similar concealed space

• Floor or ceiling

Maintain minimum clearances to combustibles

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualied installer, service agency or your dealer.

September 1, 2008

Page 19

4300 Wood Stove Series (ACC)

 ft. (91cm)

Minimum

Less than 10 ft. (05cm)

2 ft. (61cm)

 ft. (91cm)

Minimum

10 ft. (05cm) To Nearest Roofline

2 ft. (61cm)

Pitched Roof

10 ft. (05cm) or more

 ft. (91cm) Minimum

Less than 10 ft. (05cm)

2 ft. (61cm)Minimum

 ft. (91cm) Minimum

Wall or Parapet

Flat Roof

D. Chimney Termination Requirements

Follow manufacturers instructions for clearance, securing, ashing and terminating the chimney.

• Must have an approved and listed cap

• Must not be located where it will become plugged by

snow or other material

• Must terminate at least  feet (91cm) above the roof

and at least 2 feet (61cm) above any portion of the roof within 10 feet (05cm)

• Must be located away from trees or other structures

E. 2-10-3 Rule

These are safety requirements and are not meant to assure proper ue draft.

NOTE:

• Chimney performance may vary.

• Trees, buildings, roof lines and wind conditions affect performance.

• Chimney height may need adjustment if smoking or overdraft occurs.

Figure 19.1

Figure 19.2

September 1, 2008

7037-135E

Page 19

Page 20

4300 Wood Stove Series (ACC)

SparkArestor Cap

Roof Flashing

Storm Collar

Joist Shield/Firestop

Double wall connector pipe

Floor Protector

Outside Air Floor Vent

OutsideAir Rear Vent

Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit Part

OAK-ACC and (depending on oor installation)

Part SRV7033-041 for installation in a mobile home.

1. An outside air inlet must be provided for combustion See

page 14 for installation information.

2. Appliance must be secured to the mobile home structure by bolting the pedestal through hearth pad and into oor.

. Appliance must be grounded with #8 solid copper

grounding wire or equivalent and terminated at each end with N.E.C. approved grounding device.

4. Appliance must be installed with an approved UL10 HT ventilated chimney connector, UL10 HT chimney, and terminal cap with spark arrestor. Never use a single wall connector (stove pipe) in a mobile home installation. Use only double-wall connector pipe, Dura-Vent DVL, Selkirk metalbestos DS or Security DL double-wall connector or any listed double-wall connector pipe.

In Canada, this appliance must be connected to a 6 inch (152mm) factory-built chimney conforming to CAN/ULC629M, STANDARD FOR FACTORY BUILT CHIMNEYS.

6. Follow the chimney and chimney connector manufacturer’s instructions when installing the ue system for use in a mobile home.

7. Maintain clearance to combustibles.

8. Floor pr otect ion req uire ments mu st be follo wed precisely.

9. Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the exterior of the structure.

NOTE: Offsets from the vertical, not exceeding 45°, are allowed per Section 905(a) of the Uniform Mechanical Code (UMC). Offsets greater than 45° are considered horizontal and are also allowed, providing the horizontal run does not exceed 75% of the vertical height of the vent. Construction, clearance and termination must be in compliance with the UMC Table 9C. This installation must also comply with NFPA

211. NOTE: Top sections of chimney must be removable to allow

maximum clearance of 1.5 feet (411cm) from ground level for transportation purposes.

Figure 20.1

CAUTION

Maintain structural integrity of mobile home:

• Floor, wall, ceiling and/or roof.

Do NOT cut through:

• Floor joist, wall, studs or ceiling trusses.

• Any supporting material that would affect the structural integrity.

10. Burn wood only. Other types of fuels may generate poisonous gases (e.g., carbon monoxide).

11. If unit burns poorly while an exhaust blower is on in home, (i.e., range hood), increase combustion air.

12. Installation shall be in accordance with the Manufacturers Home & Safety Standard (HUD) CFR 280, Part 24.

Page 20

7037-135E

WARNING

Asphyxiation Risk.

• Never install in a sleeping room. Consumes oxygen in the room.

September 1, 2008

Page 21

Appliance Set Up

Door handle must be in open position to tighten set screw

Set Screw

(align with flat

side of rod)

Ash Door Rod shown in installed position

Remove for installation and then re-install

Gasket

Slide rod at an angle into slot

Ash Door Assembly

Magnet

Lay stove flat on protective padding or pallet

Door Handle

A. Pedestal Assembly and Ash Removal

System (ARS) Installation for Step Top Uni-body

NOTE: The Ash Removal System, must be

installed rst before installing the pedestal.

Included in Kit: Door assembly, door handle & magnet, ash drawer, fastener package. A cover plate that is required for a oor outside air installation on a pedestal model is also included, If not needed, discard.

Tools Required: Phillips head screwdriver, 7/16 socket wrench, /2 and 5/6 Allen wrench.

Begin installing the ARS System.

1. Remove 2 front bricks as shown in Figure 21.1.

Lay body of stove on its back on a protective pad or pallet.

. Remove the 2 nuts and 2 bolts holding the channel in

place and set the channel aside. Discard the 2 nuts.

nstall the gasket over the 4 protruding screws.

The glossy side of the gasket needs to go against the rebox bottom.

4300 Wood Stove Series (ACC)

Figure 21.1

4. Install ash door assembly by sliding the rod at an angle

6. Install magnet using a Phillips head screwdriver. This

September 1, 2008

It is important the gasket is not put on upside down as it could compromise its sealing capabilities. Figure 21.2.

into the slot on the left side. As the rod starts passing through the slot, slide the handle over the rod and then nish pushing the rod through the slot.

Slide the ash door over the 4 screws protruding from the bottom of the stove. Secure with nuts provided. Figure

21.2.

Using a /2 Allen wrench tighten the set screw in the door handle. The set screw needs to be snug. Figure 21.3.

magnet will hold the door handle in an open position which in turn holds the ash door open so ashes can be brushed into the ash drawer. Figure 21.2.

Do NOT operate before fully assembling components.

Burning your stove without a pedestal or leg kit attached:

• Will void your warranty.

• May result in property damage or personal injury.

WARNING

7037-135E

Figure 21.2

Figure 21.3

Page 21

Page 22

4300 Wood Stove Series (ACC)

Grate

ARS

Channel

Replace both bricks

back into firebox

Cover Plate

Ash Removel

Drawer

Adapters

Oak

Pedestal

Trim

Pedestal and Ash Removal System (Cont’d)

Installing Pedestal Assembly

1. Remove screws on adapter and slide pedestal over

adapter on bottom of stove. Figure 22.1.

2. Line up holes in sides of pedestal with holes in adapter.

. Securely tighten pedestal into place.

4. Carefully stand stove up and place in desired location.

5. Slip wooden decorative strips onto pedestal edges.

Finishing the ARS Installation

1. Re-install the ARS channel that was removed in Step  on page one

et the grate into the ARS channel Replace the 2

front cut bricks.

2. Install the ash drawer.

.

Check to make sure bafe boards and ceramic blanket are in their proper locations. (see page 29).

NOTE: If installing a oor installation of an outside air kit on a

Step Top model with a pedestal assembly you must attach the enclosed cover plate to the back of the stove. Other wise you may discard this piece. Figure 22.3.

and secure with 2 bolts previously removed.

Figure 22.2.

Figure 22.2

Figure 22.1

Page 22

7037-135E

Figure 22.3

September 1, 2008

Page 23

B. Leg Kit and Ash Removal Installation

Lay stove flat on its back on protective padding or pallet

Insert 2 bottom screws loosely

Ash Drawer

Leg Brackets

Leg Mounting Brackets are packaged inside firebox.

Leveling Legs at opposite corners

(ARS) for Step Top Uni-Body

NOTE: The Ash Removal System, must be

installed rst before installing the legs.

Installing Leg Kit

Remove leg mounting brackets packaged inside rebox.

2. Attach

. Loosely assemble bolts into the corner of the mounting

4. Slide legs onto mounting brackets and tighten. Make sure

5. Carefully stand stove up and place in desired location.

6. Use leveling bolts on legs to stabilize and level stove.

the 2 bottom screws of the mounting brackets to the bottom of the stove with 1/4”-20 Phillips head screws. These screws are located in the component pack .

Leave the bottom 2 screws loose so you can slide the ash pan assembly bottom slots over the screw heads. This allows the weight of the ash pan to rest on the screws while you are attaching the top 2 screws. Once the ash pan is attached, tighten all screws. Figure 23.2.

brackets for leg attachment. Figure 23.1.

the legs are up against the bracket. There are leveling bolts in 2 legs. These leveling legs should be in opposite corners.

Figure 23.1.

Do NOT tilt up on the cast iron legs, it could damage the legs.

4300 Wood Stove Series (ACC)

Figure 23.2

CAUTION

Do NOT tilt the unit on the cast iron legs.

• Tilting could lead to property damage.

• Lift the unit upright and place it into position on the oor protector.

Finishing the ARS Installation

Follow steps 1 through  on page 22. See also Figure

22.2.

Figure 23.1

September 1, 2008

7037-135E

Page 2

Page 24

4300 Wood Stove Series (ACC)

Locknut

Door Cross Section (example)

Latch Cam

Spacing Washers

Square Key

Door Handle

Spring

Handle

C. Door Handle Assembly

1. Install washer on door handle shaft.

2. Slide door handle through door.

. Install second washer(s) as shown.

4. Install key in groove.

5. Align groove in latch cam with key; slide latch cam over shaft

6. Install locknut but do not overtighten, it must move smoothly.

7. Install spring handle turning in a counter-clockwise motion to desired location on door handle rod.

CAUTION

• Do NOT overtighten lock nut.

• Door handle needs to move smoothly.

D. Adjusting The Blower Speed Control

The blower speed control for this unit is adjusted at the factory, and normally does not require further adjustment.

OTE: When the speed control is turned clockwise,

it will click on to high speed. Continue to turn the speed control clockwise to decrease the speed. At full clockwise, the blower should blow gently, but should not stop.

1. With the appliance plugged in, turn the speed control knob to slow (full clockwise).

2. With a small screwdriver, adjust the blower speed by turning the adjustment mechanism through the hole on the side of the speed control.

. Adjust the speed so the blower runs slowly, but

does not stop. Turn clockwise to slow the blower and counterclockwise to increase the speed.

Figure 24.1

Page 24

7037-135E

September 1, 2008

Page 25

Operating Instructions

A. Over-Firing Your Appliance

WARNING

Fire Risk

Do not over-re.

Over-ring may ignite creosote or will damage the stove and chimney.

To prevent over-ring your stove, DO NOT:

• Use ammable liquids

• Overload with wood

• Burn trash or large amounts of scrap lumber

• Permit too much air to the re

1. Symptoms of Over-Firing

Symptoms of over-ring may include one or more of the following:

• Chimney connector or appliance glowing

• Roaring, rumbling noises

• Loud cracking or banging sounds

• Metal warping

• Chimney re

2. What To Do if Your Stove is Over-Firing

• Immediately close the door and air controls to reduce air supply to the re.

• If you suspect a chimney re, call the re department and evacuate your house.

• Contact your local chimney professional and have your stove and stove pipe inspected for any damage.

• Do not use your stove until the chimney professional informs you it is safe to do so.

Hearth & Home Technologies WILL NOT warranty stoves that exhibit evidence of over-ring. Evidence of over-ring includes, but is not limited to:

• Warped air tube

• Deteriorated refractory brick retainers

• Deteriorated bafe and other interior components

B. Wood Selection & Storage

Burn only dry seasoned wood. Store wood under cover, out of the rain and snow. Dry and well-seasoned wood will not only minimize the chance of creosote formation, but will give you the most efcient re. Even dry wood contains at least 15% moisture by weight, and should be burned hot enough to keep the chimney hot for as long as it takes to dry the

4300 Wood Stove Series (ACC)

B. Wood Selection & Storage (Cont’d)

wood out - about one hour. It is a waste of energy to burn unseasoned wood of any kind.

Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing dead wood can be considered to be about 2/ seasoned. To tell if wood is dry enough to burn, check the ends of the logs. If there are cracks radiating in all directions from the center, it is dry. If your wood sizzles in the re, even though the surface is dry, it may not be fully cured.

Splitting wood before it is stored reduces drying time. Wood should be stacked so that both ends of each piece are exposed to air, since more drying occurs through the cut ends than the sides. This is true even with wood that has been split. Store wood under cover, such as in a shed, or covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc., as uncovered wood can absorb water from rain or snow, delaying the seasoning process.

C. Burning Process

In recent years there has been an increasing concern about air quality. Much of the blame for poor air quality has been placed on the burning of wood for home heating. In order to improve the situation, we at Quadra-Fire have developed cleaner-burning woodstoves that surpass the requirements for emissions established by our governing agencies. These woodstoves, like any other appliances, must be properly operated in order to insure that they perform the way they are designed to perform. Improper operation can turn most any wood stove into a smoldering environmental hazard.

1. Kindling or First Stage

It helps to know a little about the actual process of burning in order to understand what goes on inside a stove. The rst stage of burning is called the kindling stage. In this stage, the wood is heated to a temperature high enough to evaporate the moisture which is present in all wood. The wood will reach the boiling point of water (212°F) and will not get any hotter until the water is evaporated. This process takes heat from the coals and tends to cool the appliance.

Fire requires three things to burn - fuel, air and heat. So, if heat is robbed from the appliance during the drying stage, the new load of wood has reduced the chances for a good clean burn. For this reason, it is always best to burn dry, seasoned rewood. When the wood isn’t dry, you must open the air controls and burn at a high burn setting for a longer time to start it burning. The heat generated from the re should be warming your home and establishing the ue draft, not evaporating the moisture out of wet, unseasoned wood, resulting in wasted heat.

September 1, 2008

7037-135E

Page 25

Page 26

4300 Wood Stove Series (ACC)

HIGH

MED

LOW

Burn Rate Air Control

Start-Up Air Control

Manual

Timer (ACC)

Shut Down

Pull Forward to Shut Down

2. Second Stage

The next stage of burning, the secondary stage, is the period when the wood gives off ammable gases which burn above the fuel with bright ames. During this stage of burning it is very important that the ames be maintained and not allowed to go out. This will ensure the cleanest possible re. If the ames tend to go out, it is set too low for your burning conditions. The air control located at the upper right hand corner is used to adjust for burn rates. This is called the Burn Rate Air Control. Figure 26.1.

3. Final Stage

The nal stage of burning is the charcoal stage. This occurs

when the ammable gases have been mostly burned and only charcoal remains. This is a naturally clean portion of the burn. The coals burn with hot blue ames.

It is very important to reload your appliance while enough lively hot coals remain in order to provide the amount of heat needed to dry and rekindle the next load of wood. It is best to open the Burn Rate Air and Start-Up Air Controls before reloading. This livens up the coalbed and reduces excessive emissions (opacity/smoke). Open door slowly so that ash or smoke does not exit appliance through opening. You should also break up any large chunks and distribute the coals so that the new wood is laid on hot coals.

Air quality is important to all of us, and if we choose to use wood to heat our homes we should do so responsibly. To do this we need to learn to burn our stoves in the cleanest way possible. Doing this will allow us to continue using our wood stoves for many years to come.

The second function of the Start-Up Air Control is operation of the rear air system. The rear air is used primarily during a High Burn Rate. However, in some instances rear air is desired during normal operation to help with combustion of fuel towards the back of the rebox particularly when burning hardwoods. The rear air is controlled independently from the ACC system. Slide the Start-Up Air Control between the rst and third marker as indicated on the label to allow rear air to enter the rebox. Figure 26.1.

2. Manual Timer Over-Ride

If you need to shut the ACC system off before it shuts itself off after 25 minutes (i.e. overre situation), reach down to the bottom right rear corner and pull the lever toward you.

Figure 26.2.

D. Automatic Combustion Control (ACC)

Typically, when you build a re, you open the air controls fully and monitor the re to prevent it from going into an overre situation and/or burning your wood up too quickly before you shut down the air controls to the desired burn rate. With the Automatic Combustion Control (ACC) system, you do not have to continually monitor the re. Once you set the ACC system it will control the re for you. Follow the instructions below to learn how to operate your stove with ease.

E. Air Controls

1. Start-Up Air Control

The Start-Up Air Control has two primary functions. The rst function is to activate the Automatic Combustion Control system (ACC). This function is performed by sliding the control all the way back until it stops at the “HI” indicator on the label and then pulling forward to the front of the stove until it stops. This activates the ACC system and opens the front air channel and allows air to enter the front of the stove for approximately 25 minutes. The front air channel gradually shuts down until it is completely closed at the end of the 25 minutes. The re is now controlled by the air supplied by the Burn Rate Air Control. This function should be performed each time you reload the stove. Figure 26.1.

Page 26

7037-135E

Figure 26.1

Figure 26.2

September 1, 2008

Page 27

4300 Wood Stove Series (ACC)

START-UP

REARAIR

Closed

Wide Open

“HI” setting

over-rides

Timer

High (Open)

Low (Closed)

Start-Up Air Control

Burn Rate Air Control

Front Air Channel

Operated by Timer

Rear Air Channel

Operates independently

from Timer

HIGH

LOW

Timer

Timer Manual

Shut-off

Shown with Side Shield Removed

2. Burn Rate Air Control

This air supply enters at the upper front of the rebox, near the top of the glass door. This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping to create second, third and fourth combustions. This air is regulated by the Burn Rate Air Control. There are four settings High, Medium-High, Medium-Low and Low. When the control is raised all the way up it is on the High setting and when pushed all the down it is on the Low setting. Figure 27.1.

F. Burn Rates and Operating Efciency

For maximum operating efciency

1. This appliance has a timer system (ACC) that operates the stove at its maximum efciency removing any guess work for the homeowner. Follow the instructions below for each burn rate for the Start-Up Air Control and Burn Rate Air Control. Figure 27.1.

2. Burn dry, well-seasoned wood.

Burn Rates

1. Starting a Fire and Reloading

Open both controls fully by raising the Burn Rate Air Control all the way up until it stops and slide the Start-up Air Control back until it stops. After loading the stove with wood and starting the re, set both controls to the desired setting by following the burn rate instructions below.

Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr

Raise the Burn Rate Air Control up to the bottom of the middle marker and stop. Slide the Start-Up Air Control all the way back until it stops (HI marker) and then pull forward until it stops. This activates the timer system (ACC).

5. Low Burn Rate - Below 10,000 BTU/hr

Leave the Burn Rate Air Control at the bottom marker. Slide the Start-Up Air Control all the way back until it stops (HI marker) and then pull forward until it stops. This activates the timer system (ACC).

September 1, 2008

NOTE:

These are approximate settings, and will vary with type of wood or chimney draft. Due to altitude and other environmental circumstances, this operational information is a guideline only.

2. High Burn Rate - Maximum Heat

Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position. Slide the Start-Up Air Control all the way back until it stops (HI marker) and leave it there. This setting over-rides the timer system (ACC) so you must monitor the re closely while in this setting.

WARNING

Risk of Fire.

When set on High Burn Rate and over-riding the Automatic Combustion Control system an overre situation can occur and may result in a chimney re.

Overring will void the stove warranty.

Medium-High Burn Rate - 15,000 to 30,000 BTU/hr

Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position. Slide the Start-Up Air Control all the way back until it stops (HI marker) and then pull forward until it stops. This activates the timer system (ACC).

Figure 27.1

NOTE: Operate appliance on High Burn 15 minutes a

day to help keep ue/chimney clean.

7037-135E

After activating the timer (ACC), if the control is placed within the rear air section on the label it will allow rear air to enter the rebox. This will not interfere with the timer gradually closing the front air channel in 25 minutes. If control is set on “HI” it over-rides the timer (ACC).

Page 27

Page 28

4300 Wood Stove Series (ACC)

2 pc Baffle Board

Ceramic Blanket on Top

Tube Channels

Baffle Board even with front tube & resting on all tubes

Burn Rate Air Control

Start-Up

Air

Control

G. Building A Fire

Before lighting your rst re in the stove:

1. Conrm the bafe is correctly positioned. It should be

even with the front tube and resting on all tubes. Figure

28.1.

2. Follow instructions on page 32 for cleaning plated sur-

faces, if applicable.

. Remove all labels from glass.

There are many ways to build a re. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning kindling, which in turn ignites the slow-burning rewood. Here is one method that works well:

Open the Burn Rate Air and Start-Up Air Controls fully.

2. Place several wads of crushed paper on the rebox oor. Heating the ue with slightly crumpled newspaper before adding kindling keeps smoke to a minimum.

. Lay small dry sticks of kindling on top of the paper.

4. Make sure that no matches or other combustibles are in the immediate area of the appliance. Be sure the room is adequately ventilated and the ue unobstructed.

5. Light the paper in the appliance. NEVER light or rekindle re with kerosene, gasoline, or charcoal lighter uid; the results can be fatal.

6. Once the kindling is burning quickly, add several fulllength logs  inches (76mm) or 4 inches (102mm) in diameter. Be careful not to smother the re. Stack the pieces of wood carefully; near enough to keep each other hot, but far enough away from each other to allow adequate air ow between them.

7. Set the Burn Rate Air Control and activate the timer system (ACC).

8. When ready to reload, It is best to fully open both the Burn Rate Air and Start-up Air Controls before reload- ing. This livens up the coalbed and reduces excessive emissions (opacity/smoke). Open door slowly so that ash or smoke does not exit appliance through opening. Large logs burn slowly, holding a re longer. Small logs burn fast and hot, giving quick heat.

As long as there are hot coals, repeating steps 6 through 8 will maintain a continuous re throughout the season.

NOTE:

• Build re on brick rebox oor.

• Do NOT use grates, andirons or other methods to support fuel.

It will adversely affect emissions.

Figure 28.1

WARNING

Fire Risk

Do NOT store wood:

• Closer than required clearances to combustibles to appliance

• Within space required for loading or ash removal.

Do NOT operate appliance:

• With appliance door open.

• With ash removal system door open.

WARNING

Fire Risk.

• Do NOT burn wet or green wood.

• Store wood in dry location.

• Stack wood so both ends are exposed to air.

Wet, unseasoned wood can cause accumulation of creosote.

Page 28

7037-135E

September 1, 2008

Page 29

4300 Wood Stove Series (ACC)

Ceramic Blanket

Back of Firebox

Baffle Board

Ceramic Blanket

Back of Firebox

Baffle Board

H. Correct Bafe & Ceramic Blanket Placement

WARNING

Fire Risk

Firebox damage due to improper bafe placement is not covered by warranty. Operate the

wood burning appliance with the bafe in the correct position only.

Not doing so could result in:

• Overheating the chimney

• Overheating the rear of the rebox

Ensure correct bafe placement and replace bafe components if damaged or missing.

CORRECT POSITION

• Reduced efciency

• Poor performance

INCORRECT POSITIONS

Ceramic Blanket and Bafe Board are NOT in

contact with the back of the rebox.

Ceramic Blanket and Bafe Board MUST be in contact with the back of the rebox and even with each other in the front.

Figure 29.1

Ceramic Blanket is NOT in contact with the

back of the rebox and NOT even with the Baf-

e Board in the front.

Ceramic Blanket is bunched up at the back of

the rebox and NOT even with the Bafe Board

in the front.

September 1, 2008

Figure 29.2

7037-135E

Page 29

Page 30

4300 Wood Stove Series (ACC)

I. Blower Operating Instructions

NOTE: If your Quadra-Fire wood stove is equipped with an

optional blower, you should follow these guidelines:

1. Initial (cold) start-up and all Burn Settings

The blower can be plugged in and turned on right away. The blower fan is turned on and off by a snap disc. When your stove has reached a certain temperature the blower will turn on and when your stove has cooled down to a certain temperature it will turn off.

NOTE: The blower can still be left on at all burn rates even if you have deactivated the snap disc with the manual over-ride knob. See page 15.

2. The blower is equipped with a speed control. Adjust the fan speed by turning the speed control clockwise to “Low” or counterclockwise to “High”.

. Snap Disc Location

If you nd the blower coming on and off at undesirable temperatures, relocate the snap disc to another location in the designated zone on the back of the appliance. Figure 29.1. There is a manual over-ride switch to deactivate the snap disc, if necessary. See page 15.

J. Opacity (Smoke)

This is the measure of how cleanly your appliance is burning. Opacity is measured in percent; 100% opacity is when an object is totally obscured by the smoke column from a chimney, and 0% opacity means that no smoke column can be seen. As you become familiar with your appliance, you should periodically check the opacity. This will allow you to know how to burn as nearly smoke-free as possible (goal of 0% opacity).

WARNING

Fire Risk.

• Do NOT burn garbage or ammable uids

such as gasoline, naptha or engine oil.

• Do NOT burn treated wood or wood with salt (driftwood).

• May generate carbon monooxide if burn material other

than wood.

May result in illness or possible death.

WARNING

Fire Risk.

Keep combustible materials, gasoline and other ammable vapors and liquids clear of appliance.

• Do NOT store ammable materials in the appliance’s vicinity.

• Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter uid or similar liquids to start or “freshen up” a re in this heater.

• Keep all such liquids well away from the heater while it is in use.

• Combustible materials may ignite.

Figure 30.1

Odors and vapors released during initial operation.

• Curing of high temperature paint.

• Open windows for air circulation.

Odors may be irritating to sensitive individuals.

CAUTION

K. Frequently Asked Questions

ISSUES SOLUTIONS

Odor from appliance When rst operated, this appliance may release an odor for the rst several hours. This is

caused by the curing of the paint and the burning off of any oils remaining from manufacturing.

Metallic noise Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the appliance.

Whirring sound If the optional blower has been installed, the blower produces a whirring sound which

increases in volume as the speed is increased.

Page 0

7037-135E

September 1, 2008

Page 31

Maintaining & Servicing Your Appliance

A. General Maintenance

1. Creosote (Chimney) Cleaning

• Frequency: Every 2 months during heating season or

as recommended by a certied chimney sweep; more frequently if chimney exceeds or is under 14-16 ft. (measured from bottom of appliance)

• By: Certified Chimney Sweep

Remove all ash from the rebox and extinguish all hot embers before disposal. Allow the appliance to cool completely. Disconnect ue pipe or remove bafe and ceramic blanket from appliance before cleaning chimney. Otherwise residue can pile up on top of the bafe and ceramic blanket and the appliance will not work properly. (See Bafe Removal on page 34). Close the door tightly. The creosote or soot should be removed with a brush specically designed for the type of chimney in use. Clean out fallen ashes from the rebox.

It is also recommended that before each heating season the entire system be professionally inspected, cleaned and repaired if necessary.

Inspection: Inspect the system at the appliance connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the bottom.

Formation and Need For Removal: When wood is burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney ue of a newly-started or a slow-burning re. As a result, creosote residue accumulates on the ue lining. When ignited, this creosote creates an extremely hot re which may damage the chimney or even destroy the house. The chimney connector and chimney should be inspected once every 2 months during the heating season to determine if a creosote or soot buildup has occurred. If creosote or soot has accumulated, it should be removed to reduce the risk of a chimney re.

4300 Wood Stove Series (ACC)

3. Ash Removal System (ARS) Operating and Cleaning

• Frequency:

• By: Homeowner

As necessary

CAUTION

Injury Risk.

• Gloves recommended

• May have sharp edges

a. The stove and ashes must be completely cooled down

before using the Ash Removal System. Reach down and locate the ash removal door handle under the left side of the stove in the center. Squeeze the handle and push all the way back. A magnet will hold the handle in place which in turn holds the ash door open.

b. Clean ash down through the ash removal system grate into

the drawer below. If there are large pieces in the ashes, you can remove the grate before brushing the ash into the drawer.

Make sure all ash is removed from the top of ARS door. Lift up the grate and inspect the top of the door to ensure all ash has been removed. You can rapidly move the ARS latch handle up and down to help remove any ash from the door. Use a small brush to clean off the top of the door if any ash remains.

Be sure to replace the grate before operating the stove. Remember to leave 1/4 to 1/2 inch (6-1mm) of ash on the rebox oor to act as a natural grate, allowing air to ow freely underneath wood.

c. Close the door handle, you will hear a “click” when it closes.

The ash drawer will not pull out if the door handle is left in the open position. Wear gloves to remove the drawer. Dispose of the ashes following the directions below.

WARNING

Fire Risk.

Prevent creosote buildup.

• Inspect chimney connector and chimney once every two months during heating season.

• Remove creosote to reduce risk of chimney re.

• Ignited creosote is extremely HOT.

Fire Risk.

• Do not use chimney cleaners or ame colo

rants in your appliance.

Will corrode pipe.

September 1, 2008

WARNING

7037-135E

Fire Risk Injury Risk

Make sure Ash Removal System door is sealed tight against the gasket.

Air leakage may cause:

• Over-re condition.

• Flame and/or smoke spillage.

• Wood to burn too fast.

Page 1

Page 32

4300 Wood Stove Series (ACC)

Glass

Assembly

3. Disposal of Ashes

• Frequency:

When ash is within 1-/4 in. (44mm) of firebox

lip

• By: Homeowner

Ashes should be placed in a metal container with a tight tting lid. The closed container of ashes should be placed on a non-combustible oor or on the ground, well away from all combustible materials, pending nal disposal.

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled.

WARNING

Fire Risk.

Disposal of Ashes

• Ashes should be placed in metal container with tight tting lid.

• Do n ot pla ce metal contain er on combusti bl e surface.

• Ashes should be retained in closed container until all cinders have thoroughly cooled.

5. Glass Cleaning

• Frequency:

As desired

• By: Homeowner

Clean glass with a non-abrasive glass cleaner. Abrasive cleaners may scratch and cause glass to crack. If the deposits on the glass are not very heavy, normal glass cleaners work well. Heavier deposits may be removed by using a damp cloth dipped in wood ashes or by using a commercially available oven cleaner.

After using an oven cleaner, it is advisable to remove any residue with a glass cleaner or soap and water. Oven cleaner left on during the next ring can permanently stain the glass and damage the nish on plated metal surfaces.

A portion of the combustion air entering the rebox is deected down over the inside of the door glass. This air ow “washes” the glass, helping to keep smoke from adhering to its surface.

When operated at a low burn rate, less air will be owing over the glass and the smokey, relatively cool condition of a low re will cause the glass to become coated.

Operating the appliance with the Burn Rate Air Control and Start-Up Air Control all the way open for 15-20 minutes should remove the built up coating.

4. Cleaning Plated Surfaces

• Frequency: Prior to first burn and then as desired

• By: Homeowner

Clean all the ngerprints and oils from plated surfaces BEFORE ring the appliance for the rst time. If not cleaned properly before lighting your rst re, the oils can cause permanent markings on the plating.

After the plating is cured, the oils will not affect the nish and little maintenance is required. Wipe clean as needed.

CAUTION

• Do not use polishes with abrasives.

It will scratch plated surfaces.

CAUTION

Handle glass assembly with care.

When cleaning glass:

• Avoid striking, scratching or slamming glass.

• Do NOT clean glass when hot.

• Do NOT use abrasive cleaners.

• Use a hard water deposit glass cleaner on white lm.

• Use commerical oven cleaner on heavier deposits.

• Remove all residue of oven cleaner or will permanently stain glass on next ring.

•

Refer to maintenance instructions.

Page 2

7037-135E

September 1, 2008

Page 33

B. Glass Replacement

Glass

Assembly

1. Ensure that the re is out and the appliance is cool to the touch.

2. Protect a table or counter top with padding or towels. Protect your hands and wear gloves to prevent injury.

. Remove the door with the broken glass by lifting the

door up and off of the hinges.

Lay door face down on a table or counter making sure the handle hangs over the edge so the door lays at, on a soft surface.

5. Remove the screws from each glass retainer and remove the glass. (If screws are difcult to remove, soak with penetrating oil rst).

6. Center the glass with edges evenly overlapping the opening in the door, (i.e. same space top and bottom, left and right sides).

7. Replace the glass retainers. Be careful not to cross thread the screws.

8. Tighten each retainer just a few turns until each is secured. Check again for centering of glass in door frame. Continue to tighten each retainer alternately, a few turns at a time, until the glass is secure. DO NOT OVERTIGHTEN.

9. Replace the door on the appliance.

4300 Wood Stove Series (ACC)

WARNING

Handle glass with care.

• Inspect the gasket to ensure it is undamaged.

• Do NOT strike, slam or scratch glass.

• Do NOT operate appliance with glass & door assembly removed.

• Do NOT operate with glass cracked, broken or scratched.

WARNING

Fire Risk. Injury Risk.

• Use only glass specied in manual.

• DO NOT REPLACE with any other material.

Glass breakage will occur.

Quadra-Fire stoves are equipped with ceramic super heat-resistant glass, which can only be broken by impact or misuse.

Do not slam stove door or impact the glass. When closing door, make sure that logs do not protrude against the glass. Inspect glass regularly.

If you nd a crack or break, immediately put the re out and return the door to your dealer for replacement of glass before further use.

September 1, 2008

7037-135E

Page 

Page 34

4300 Wood Stove Series (ACC)

9 in.

2-1/2 in.

2 in.

6-/8 in.

7-1/4 in.

 in.

9 in.

No Brick, ARS Grate Location

9 in.

2-1/2 in.

2 in.

6-/8 in.

7-1/4 in.

 in.

9 in.

C. Firebrick Replacement

Replace the rebrick if they become crumbly and/or if there is a 1/4 inch (6.5mm) gap between the bricks.

Inspect the rebrick after each ash removal.

The rebox is lined with high quality rebrick, which has exceptional insulating properties. There is no need to use a grate; simply build a re on the rebox oor. Do not operate appliance without rebrick.

1. After the coals have completely cooled, remove all old brick and ash from unit and vacuum rebox.

2. Remove new brick set from box and lay out to diagram shown.

. Lay bottom bricks in unit.

4. Install rear bricks on the top of the bottom bricks. Slide top of bricks under clip on back of rebox wall and push bottom of brick back.

5. Install side bricks. Slide top of brick under clips on side of rebox and push the bottom of the brick until it is ush with the side of the appliance.

Figure 34.1 - 4300 Millennium Top Brick Assembly

Figure 34.2 - 4300 Step Top Brick Assembly

No. Brick Size Qty

1 9 x 4-1/2 x 1-1/4 10

2 6 x 4-1/2 4

3 4-1/2 x 4-1/2 x 1-1/4 2

4 9 x 4-1/2 with angles 1

5 9 x  with angle 1

6 9 x 2 x 1-1/4 2

Use Part 82-0550 when ordering individual brick. Provide brick dimension or copy this page, mark the desired brick and take it to your authorized dealer.

NOTE: The Ash Removal System is only available for the Step Top Model and not for the Millennium Model.

No. Brick Size Qty

1 9 x 4-1/2 x 1-1/4 12

2 6 x 4-1/2 4

Page 4

3 9 x 4-1/2 with angles 1

4 9 x  with angle 1

5 9 x 2 x 1-1/4 2

7037-135E

September 1, 2008

Page 35

4300 Wood Stove Series (ACC)

Magnet

Spade

Connectors

Snap Disc

Snap Disc Location

D. Bafe Removal

1. Remove all ash from the rebox, and extinguish all hot embers before disposal into a metal container.

2. The bafe board has 2 pieces. With the ceramic blanket still in place, slide one bafe piece over the top of other one and pull out top piece through the door opening and then remove bottom bafe piece. Figure 35.1.

. Remove the ceramic blanket.

4. Re-install the bafe pieces one piece at a time. Be sure the bafe boards are even with the front manifold tube and is resting on all tubes. Figure 29.1 on page 29.

5. To re-install the ceramic blanket, it is easier to fold it in half rst. Place on top of bafe board, open up and atten and smooth out the blanket. Re-check the bafe board for correct positioning. Figure 35.2.

E. Snap Disc Replacement

1. Locate the snap disc bracket assembly at the bottom left

rear corner of the stove. Figure 35. 3.

2. A magnet holds the bracket to the stove. Pull the bracket down away from the stove to expose the snap disc.

. Pull the snap disc and spade connectors up and out of

bracket as shown in Figure 35.4.

4. Using a Phillips head screw driver, remove the 2 screws from the snap disc and then remove the snap disc from the spade connectors. Replace with new snap disc and re-connect to spade connectors.

5. Push the snap disc and spade connectors back inside bracket and re-attach the bracket to the stove.

Figure 35.1 - Bafe

Figure 35.2 - Ceramic Blanket

Figure 35.3

Figure 35.4

September 1, 2008

7037-135E

Page 5

Page 36

4300 Wood Stove Series (ACC)

Channel Access Cover

Channel Nuts (2)

Side Panel

Tube Channel Assembly

Channel Cover Screws (4)

Tube Channel Rack

Remove 2 Screws

Slide one gasket over each tube

F. Tube Channel Assembly Replacement

Removing Tube Channel Assembly

1. Remove the right side shield by removing 2 screws in the back using a Phillips head screw driver.

2. Remove 4 screws from channel access cover and remove cover.

. Locate 2 channel nuts inside of chamber and remove

using a 7/16 socket wrench. Slide out tube channel assembly.

NOTE: Soak the bolts with penetrating oil for at least 15 min-

utes before trying to remove them.

Replacing Tube Channel Assembly

1. Silde one gasket on each tube rst.

2. Slide the tube channel assembly into side of rebox and insert each tube into the corresponding hole in the tube channel rack starting with the back hole rst.

. Make sure tube channel assembly is ush against the

side of the stove and secure with channel nuts.

4. Re-install channel cover and side shield.

NOTE: Service Space

In order to replace the tube channel assembly a clearance of 19 inches (48mm) is required on the right side of stove in order to remove the tubes with the stove in place.

If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.

Figure 36.1

Page 6

7037-135E

September 1, 2008

Page 37

4300 Wood Stove Series (ACC)

With proper installation, operation, and maintenance your woodstove will provide years of trouble-free service. If you do experience a prob-

Troubleshooting

Start Fire Problems Possible Cause Solution

lem, this troubleshooting guide will assist a qualied service person in the diagnosis of a problem and the corrective action to be taken.

Can’t get re started Excessive smoke or spillage Burns too slowly Smolders, sizzles

Fire burns too fast Extremely dry or soft wood Mix in hardwood.

Not enough kindling/paper or no kindling/paper

Not enough air for re to ignite Check for restricted cap/shroud

Wood condition is too wet, too large

Bed of coals not established before adding wood

Flue blockage such as birds’ nests or leaves in termination cap

Down draft or negative pressure Competition with exhaust devices

Overdrafting Check for correct vent height; too much vertical

ARS door may not be closed completely

Ash left on ARS door No seal is created. Clean off top of ARS door for

Use dry kindling, more paper. Arrange kindling & wood for air movement.

Open outside air kit (if installed).

Check for ue blockage.

Pre-warm ue before starting re (refer to starting re section).

Check for adequate vent height (refer to chimney assembly section).

Open window below the appliance towards the wind.

Use dry, seasoned wood (refer to wood fuel section).

Start with paper & kindling to establish bed of coals (refer to starting re section).

Have chimney inspected for creosote and cleaned by a certied chimney sweep.

Do not use exhaust fans during start-up (refer to negative pressure section).

Open window below the appliance towards the wind.

Mix in less seasoned wood after re is established (refer to wood fuel section).

height creates overdrafting.

Check location of vent termination (refer to chimney requirements section).

Handle set screw rotated on ash door rod - Follow installation instructions

complete seal.

September 1, 2008

7037-135E

Page 7

Page 38

4300 Wood Stove Series (ACC)

Reference Materials

A. Exploded view

Glass Size: 15-1/2” wide x 1-/8” high

Figure 38.1 - Door, Glass And Door Handle Assembly

Item Description Part No.

30 Hinge Pins Gold: 832-0250

Nickel: 430-5320 31 Door, Cast not sold sep. 32 Spring Handle, 1/2 inch Gold: 832-0620

Nickel: 250-8330 40 Door Handle, Rod Only 430-1131 41 Washer, Spacing (1) 222-0010

(3) 832-0990 42 Trim Ring for Door (Trim Door

Assembly only) 43 Glass Replacement 7000-012 44 Cam Latch 430-1141 45 Nut, Locking (24) 226-0100/24 46 Key, Cam Latch 430-1151 47 Screws, Glass Frame (10) (1) 220-0490

48 Glass Frame Assembly (set) 832-0350

Gold: 430-2682 Nickel: 430-5340

(10) 832-0860

Figure 38.2 - Burn Rate Air & Start-Up Air Controls

Page 8

7037-135E

Item Description Part No.

4 Knob, Start-Up Air Control 7000-343 5 Magnet for Air Control 229-0631 6 Air Control Rod Guide, Start-Up 7033-210 7 Control Arm Assembly, Rear Air 7033-035

9 Timer Replacement SRV480-1940 10 Timer Arm Assembly 7033-034 12 Gasket, Front & Rear Air Timer

Doors 13 Burn Rate Air Control Assembly 7037-004 14 Spring Handle, 1/4 inch Gold: 832-0630

Snap Disc, F125 F-20 230-0470 49 Timer Air Control Assembly SRV7037-018

7033-282

Nickel: 250-8340

September 1, 2008

Page 39

4300 Wood Stove Series (ACC)

SIZES

(#) Bafe Board: 9-1/2” w x 15-/4” h, each (#29) Ceramic Blanket: 19” w x 1-/4” h, 1/2” thick

Figure 39.1

Item Description Item Description

1 Trim, Oak Strip for Pedestal 20 Tube Channel Assembly

2 Pedestal Base 21 Air Channel, Convection

3 Pedestal Riser 22 Bracket, Convection Mount

4 Knob, Start-Up Air Control 2 Air Supply, Back

5 Magnet for Air Control 24 Flue Collar

6 Air Control Rod Guide, Start-Up 25 Panel Assembly, Side, Left

7 Control Arm Assembly, Rear Air 26 Rear Air Channel Assembly

9 Timer, Mechanical 27 Brick, Set

10 Timer Arm Assembly 28 Tube Support Rack

12 Gasket, Front & Rear Air Doors 29 Blanket, Ceramic

13 Burn Rate Air Control Assembly 30 Hinge Pin

14 Spring Handle, 1/4 inch 31 Door, Cast (not sold separately)

16 Label for Burn Rate Air Control 2 Spring Handle, 1/2 inch

17 Label for Start-Up Air Control 33 Bafe Fiberboard, (2 pc)

18 Panel Assembly, Side, Right 34 Brick Retainer

19 Tube Channel Access Cover (Top) 49 Timer Air Control Assembly

Millennium Model

September 1, 2008

7037-135E

Page 9

Page 40

4300 Wood Stove Series (ACC)

2

2

SIZES

(#) Bafe Board: 9-1/2” w x 15-/4” h, each (#29) Ceramic Blanket: 19” w x 1-/4” h, 1/2” thick

Figure 40.1

Item Description Item Description

1 Trim, Oak Strip for Pedestal 26 Rear, Air Channel Assembly

4 Knob, Start-Up Air Control 28 Tube Support Rack

5 Magnet for Air Control 29 Blanket, Ceramic

6 Air Control Rod Guide, Start-Up 30 Hinge Pin

7 Control Arm Assembly, Rear Air 31 Door, Cast (not sold separately)

9 Timer, Mechanical 2 Spring Handle, 1/2 inch

10 Timer Arm Assembly 33 Bafe Fiberboard, (2 pc)

12 Gasket, Front & Rear Air Doors 34 Brick Retainer

13 Burn Rate Air Control Assembly 35 Legs, Queen Anne

14 Spring Handle, 1/4 inch 36

16 Label for Burn Rate Air Control 37 Ash Pan, Ash Removal System

17 Label for Start-Up Air Control 39 Flue Collar (can’t replace in eld)

18 Panel Assembly, Side, Right 49 Timer Air Control Assembly

19 Tube Channel Access Cover (Top) 50 Brick, Set

20 Tube Channel Assembly 51 Grate, Ash Removal x

21 Air Channel, Convection 52 Leg Mount Kit, Left & Right (set)

22 Bracket, Convection Mount

2

Air Supply, Back

25 Panel Assembly, Side, Left

Step-Top Uni-Body Model

Pedestal, Ash Removal (not sold separately)

Page 40

7037-135E

September 1, 2008

Page 41

4300 Wood Stove Series (ACC)

B. Service Parts & Accessories IMPORTANT: THIS IS DATED INFORMATION. When requesting a part for your appliance, please

supply serial number and model name/number to ensure correct service parts. All parts may be order from an authorized dealer.

ITEM # ACCESSORIES PART NO.

Blower Assembly BK-ACC

31 Door Assembly, Black 82-1092

31 Door Assembly, Gold Trim 82-1912

31 Door Assembly, Nickel Trim DR-1/4NL

Leg Kit & Ash Removal System, Cast Legs LEG-14-BK

Leg Kit & Ash Removal System, Gold Legs LEG-3143-GD

Leg Kit & Ash Removal System, Nickel Legs LEG-14-NL

35 Legs, Queen Anne, Matte Black 81-1240

35 Legs, Queen Anne, Nickel LEGS-QANL

35 Legs, Queen Anne, Gold 81-1250

Outside Air Kit, Floor & Rear (Termination Cap, Wire Ties, Flex Adapter, Fasteners) OAK-ACC

see pg 14 Outside Air Back Cover Plate & Sealing Rope, (1 inch x 4 ft) Floor Only SRV70-041

Pedestal Assembly & Ash Removal System PED-14

Upgrade to Nickel Door (includes Nickel Spring Handles, Hinge Pins And Logo) UK-DRNL

ITEM # SERVICE PARTS PART NO.

21 Air Channel, Convection 7033-144

6 Air Control Rod Guide, Start-Up Air 70-210

37 Ash Removal Assembly, Leg, Step Top Model 70-008

Ash Pan, Pedestal, Step Top Model 7033-010

Ash Pan, Leg, Step-Top Model 7033-050

2

33 Bafe, Fiberboard (2 pieces) SRV707-112

29 Blanket, Ceramic 1/2” thick, eld cut to size, 19” wide x 15-/4” high 82-90

22 Bracket, Convection Mount SRV70-112

34 Brick Retainer 7033-149

27 Brick, Set, Millennium SRV707-00

50 Brick, Set, Step-Top Model SRV707-012

13 Burn Rate Air Control Assembly 7037-004

44 Cam Latch (Door Handle) 430-1141

Air Supply Back SRV70-14

Blower Control Box with Switch 7000-194

Blower (Motor Only) Replacement 812-4900

Bracket, Snap Disc 7033-036

Brick, Individual 82-0550

Brick, Uncut, (Set of 6) 82-040

Channel, Ash Removal System, Step Top Model 70-172

Component Pack, Millennium Model, Black and Gold, (includes Touch-up Paint, Gold Spring Handles (1) 1/2 inch and (2) 1/4 inch, Trimount Plug, Owner’s Manual, Warranty Card)

7037-014

September 1, 2008

7037-135E

Page 41

Page 42

4300 Wood Stove Series (ACC)

ITEM # SERVICE PARTS PART NO.

Component Pack, Millennium Model, Nickel (includes Touch-up Paint, Nickel Spring Handles (1) 1/2 inch and (2) 1/4 inch, Trimount Plug, Owner’s Manual, Warranty Card)

Component Pack, Step-Top Model (includes Touch-up Paint, Owner’s Manual, Warranty Card). Spring Handles are included with Door Packaging

Component Pack, Door, Black & Gold, (includes Gold Spring Handles (1) 1/2 inch & (2) 1/4 inch, 2 Gold Hinge Pins, Quadra-Fire Logo)

Component Pack, Door, Nickel, (includes Nickel Spring Handles (1) 1/2 inch and (2) 1/4 inch, 2 Nickel Hinge Pins, Quadra-Fire Logo

Component Pack, Leg Step-Top (includes Gasket for Ash Removal, Magnet & Fasteners)

Component Pack, Pedestal Step-Top (includes Gasket for Ash Removal, Magnet & Fasteners

7 Control Arm Assembly, Rear Air 7037-005

Door Assembly, Ash Removal, Step-Top Model 7033-015

Door Handle Assembly 82-0540

Door Handle, Rod Only 430-1131

24 Flue Collar, Millennium Model SRV7000-02

Gasket, Ash Removal, Step-Top Model 70-185

Gasket, (Tape) Glass, 5 ft 82-0460

12 Gasket, Front & Rear Air Timer Doors 70-282

43 Glass Assembly, 15-1/2” W x 1-/8” H 7000-012

48 Glass Frame, Set (4 pc) 82-050

51 Grate, Ash Removal, Step-Top Model 7033-173

Handle Assembly, Ash Pan, Step-Top Model 70-274

30 Hinge Pins, Gold (2) 82-0250

30 Hinge Pins, Nickel (2) 40-520

46 Key, Cam Latch, (Door Handle) 430-1151

4 Knob, Start-Up Air Control 7000-343

16 Label for Burn Rate Air Control 7033-160

17 Label for Start-Up Air Control 7033-166

Latch, Handle Assembly, Ash Removal 7033-047

52 Leg Mount Kit, Left & Right (set) SRV707-12

Logo, Quadra-Fire, Gold 200-180

Logo, Quadra-Fire, Nickel 200-240

5 Magnet for Air Control 229-061

Magnet, Round SRV7000-140

45 Nut, Locking (Door Handle), Package of 24 226-0100/24

Outside Air Collar Assembly 7033-039

Outside Air Shield 271

Paint, Touch-Up, Matte Black 7000-304

25 Panel Assembly, Side, Left, Millennium Model 7037-007

18 Panel Assembly, Side, Right, Millennium Model 7037-006

25 Panel Assembly Side, Left, Step-Top Model 7037-011

18 Panel Assembly, Side, Right, Step Top-Model 7037-010

7037-015

7037-017

436-5350

436-5360

70-048

7033-045

Page 42

7037-135E

September 1, 2008

Page 43

4300 Wood Stove Series (ACC)

ITEM # SERVICE PARTS PART NO.

Pedestal (only) Assembly, Step-Top Model 7033-013

2 Pedestal Base, Millennium Model 7033-163

3 Pedestal Riser, Millennium Model 70-207

26 Rear Air Channel Assembly 70-002

Rope, Door, /4 in. x 84 in., eld cut to size 82-1680

47 Screws, Glass Frame, tabs are not required Qty 1: 220-0490

Qty 10: 82-0860

Snap Disc, F125 F-20, Convection Blower 20-0470

14 Spring Handle, Burn Rate Control, 1/4 inch, Gold 82-060

14 Spring Handle, Burn Rate Control,1/4 inch, Nickel 250-840

2

49 Timer Air Control Assembly SRV707-018

10 Timer Arm Assembly 7033-034

9 Timer, Mechanical SRV480-1940

42 Trim Ring, Door, Gold 40-2682

42 Trim Ring, Door, Nickel 430-5340

1 Trim, Oak Strips for Pedestal (2) 82-0560

19 Tube Channel Access Cover (Top) SRV70-27

20 Tube Channel Assembly (Manifold Tubes) SRV70-02

28 Tube Support Rack 70-148

41 Washer, Spacing (Door Handle) Qty 1: 222-0010

Spring Handle, Door, 1/2 inch, Gold 82-0620

Spring Handle, Door, 1/2 inch, Nickel 250-80

Qty 10: 82-0990

Wire Harness for Blower & Snap Disc 70-262

September 1, 2008

7037-135E

Page 4

Page 44

4300 Wood Stove Series (ACC)

C. Service And Maintenance Log

Date of Service Performed By Description of Service

Page 44

7037-135E

September 1, 2008

Page 45

D. Homeowner’s Notes

4300 Wood Stove Series (ACC)

September 1, 2008

7037-135E

Page 45

Page 46

4300 Wood Stove Series (ACC)

E. Warranty Policy

Hearth & Home Technologies LIMITED WARRANTY

Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.

Warranty Period Parts Labor Gas Wood Pellet

HHT Manufactured Appliances and Venting

EPA

Wood

Electric Venting

Components Covered

All Parts and Material Except

1 Year X X X X X X

as covered by Conditions, Exclusion, and Limitations

listed

Igniters, Electronic Compo-

nents, and Glass

2 years

X X

X X X X Blowers

X Molded Refractory Panels

 years X Firepots

5 years  years X X Castings & Bafes

7 years  years X X X

years

1 year X

Firebox, HHT Chimney, Ter-

mination & Heat Exchanger

Burners, Logs & Refractory

Limited Lifetime

1 year X

Firebox & Heat Exchanger

90 Days X X X X X X All Replacement Parts

See Conditions, Exclusions, and limitations. 9-01-08

CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY

 This warranty applies to the original owner and is transferable up to two years from date of purchase to the new

homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation.

 The maximum amount recoverable under this warranty is limited to the purchase price of the product.

 In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.

 Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home

is not covered under this warranty.

 This limited warranty does not extend to or include surface nish on the appliance or terminations, door gasketing,

glass gasketing, glass discoloration, rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, bafes, repots, doors, or rebox area are not covered by this warranty.

 Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to

this noise are not covered by this warranty.

4021-645A 09-01-08

Page 46

7037-135E

September 1, 2008

Page 47

4300 Wood Stove Series (ACC)

Hearth & Home Technologies LIMITED WARRANTY (Cont’d)

 HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or main-

tenance of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identication label furnished with the appliance; (2) installation which does not comply with local building codes; () shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those specied in the operating instructions; (6) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; and/or (7) modication of the appliance not expressly authorized and approved by HHT in writing.

 This warranty does not apply to non-HHT venting components, hearth components or other accessories used in con-

junction with the installation of this product.

 This warranty is void if the appliance has been over-red or operated in atmospheres contaminated by chlorine,

uorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

 HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship

during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.

 Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not

apply to you. This warranty gives you specic rights; you may also have other rights, which vary from state to state.

 EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE

WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE WARRANTY SPECIFIED ABOVE.

This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all warranties currently in existence.

If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HHT dealer or supplier.

4021-645A 09-01-08

September 1, 2008

7037-135E

Page 47

Page 48

CONTACT INFORMATION:

Hearth & Home Technologies

1445 North Highway

Colville, WA 99114

Division of HNI INDUSTRIES

Please contact your Quadra-Fire dealer with any questions or concerns.

For the number of your nearest Quadra-Fire dealer,

log onto www.quadrare.com

CAUTION

Do NOT discard this manual.

• Important operating and maintenance instructions included.

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

We recommend that you record the following pertinent information for your 3100 WOOD STOVE (ACC)

Date purchased/installed:

Serial Number: Location on appliance:

Dealership purchased from: Dealer phone:

Notes:

This product may be covered by one or more of the following patents: (United States) 459510, 4686807, 4766876, 47922, 481154, 5000162, 5016609, 5076254, 51184, 5191877, 521895, 526471, 52856, 541794, 54798, 5429495, 5452708, 5542407, 560107, 561487, 564740, 5688568, 5762062, 5775408, 5890485, 591661, 594127, 5947112, 5996575, 600674, 6019099, 6048195, 605165, 6145502, 6170481, 627588, 6296474, 674822, 641079, 649226, 6484712, 654698, 6550687, 6601579, 6672860, 668802B2, 6715724B2, 6729551, 6761, 6748940, 6748942, 6769426, 6774802, 679602, 6840261, 6848441, 686064, 6866205, 6869278, 6875012, 6880275, 690809, 6919884, D20652, D445174, D46246; (Canada) 1297749, 2195264, 2225408, 21972; (Australia) 780250, 78040, 1418504 or other U.S. and foreign patents pending.

Page 48

7037-135E

September 1, 2008

Hearth and Home Technologies 43M-ACC-MBK, 43ST-ACC User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual