Healthrider HRTL14508.0 User Manual
www.healthrider.com
Model No. HRTL14508.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer
satisfaction. If you have questions,
or if parts are damaged or missing,
DO NOT CONTACT THE STORE;
please contact Customer Care.
USER'S MANUAL
IMPORTANT: You must note the
product model number and serial
number (see the drawing above)
before contacting us:
CALL TOLL-FREE:
1-888-922-4222
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.healthriderservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
TABLE OF CONTENTS
ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
W
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the
warning decals. If a decal is missing or il-
legible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal
in the location shown. Note: The decals
may not be shown at actual size.
HealthRider is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of
35 or persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by persons weighing 350 lbs. (159 kg) or less.
11. When connecting the power cord (see page
14), plug the power cord into a surge suppressor (not included) and plug the surge suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 14. To purchase a surge suppressor, see
your local HealthRider dealer or call the telephone number on the front cover of this manual and order part number 146148, or see your
local electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppressor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 28 if the treadmill is not working properly.)
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 16).
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
3
8. The treadmill is capable of high speeds.
1
Adjust the speed in small increments to
void sudden jumps in speed.
a
9. The pulse sensors are not medical devices.
1
Various factors, including the user's move-
ent, may affect the accuracy of heart rate
m
readings. The pulse sensors are intended
only as an exercise aid in determining heart
rate trends in general.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the “off” position when the
treadmill is not in use. (See the drawing on
page 6 for the location of the reset/off circuit
breaker.)
ther than the procedures in this manual
o
should be performed by an authorized service
representative only.
27. The treadmill is intended for in-home use
nly. Do not use the treadmill in any commer-
o
cial, rental, or institutional setting.
28. Do not store the television in temperatures
below -40° F (-40° C) or above 140° F (60° C).
Do not operate the television in temperatures
below 23° F (-5° C) or above 90° F (35° C).
29. To protect the treadmill and television during
lightning storms, unplug the power cord from
the wall outlet and disconnect the cable system. This will prevent damage due to lightning and power line surges.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 27.) You
must be able to safely lift 45 lbs. (20 kg) to
raise, lower, or move the treadmill.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
23. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
24. Inspect and properly tighten all parts of the
treadmill regularly.
25. Never insert or drop any object into any
opening on the treadmill.
26. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
30. If an outside antenna or cable system is connected, be sure that the antenna or cable system is grounded to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
31. An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits, as
contact with them might be fatal.
32. To reduce the risk of electric shock, do not remove the cover or the back of the television.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.
4
33. Upon completion of any service or repairs to
the treadmill or the television, ask the service
technician to perform safety checks to confirm that the unit is in proper operating condition.
• Use No. 10 AWG (5.3mm2) copper, No. 8
WG (8.4mm
A
(1.0mm
2
aluminum, No. 17 AWG
)
2
) copper-clad steel or bronze wire,
or larger as a ground wire.
• Secure an antenna lead-in and ground
wires to the house with stand-off insulators
spaced from 4 to 6 feet (1.22 to 1.83 m)
apart.
• Mount an antenna discharge unit as close
as possible to where the lead-in enters the
house.
Power Lines
• Use a jumper wire not smaller than No. 6
AWG (13.3mm2) copper, or the equivalent
when a separate antenna-grounding electrode is used. See NEC Section 810-21 (j).
ote to CATV system installer: This reminder is
N
provided to call the CATV system installerʼs attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building,
as close to the point of cable entry as practical.
Ground
Clamp
Standoff
Insulators
Service
Entrance
Conductors
Service
Entrance
Equipment
Power Service Grounding
Electrode System (e.g.
Interior Metal Water Pipe)
SAVE THESE INSTRUCTIONS
Ground
Clamps
To External 75 Ohm
Terminal of Treadmill
Ground
Wire
Bonding
Jumper
Optional Antenna Grounding Electrode Driven 8
Feet (2.44 m) Into The Earth (If Required By Local
Codes). See NEC Section 810–21 (f).
Mast
Antenna
Lead-in Wire
Antenna
Discharge Unit
Ground Wire
Ground
Clamps
5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary HealthRider
H140t treadmill. The H140t treadmill offers an impressive selection of features designed to make your workouts at home more enjoyable and effective. And when
youʼre not exercising, the unique treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the front cover of this man-
Accessory Tray
Handrail
Pulse Sensor
®
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.healthriderservice.com/registration.
Before reading further, please look at the drawing
below and familiarize yourself with the labeled parts.
Personal Television/
Console
Key/Clip
Walking Belt
Foot Rail
Idler Roller
Adjustment Bolts
Reset/Off
Circuit Breaker
Power Cord
Platform Cushion
6
ASSEMBLY
3/8" Star
Washer (8)–8
#8 x 3/4" Screw
(7)–4
3/8" Nut (9)–2
#8 x 1/2" Screw
(17)–8
3/8" x 1 1/4" Patch Bolt (1)–4
3/8" x 3 3/4" Patch Bolt (2)–4
3/8" x 1 3/4" Bolt (5)–1
3/8" x 2" Bolt (6)–1
o hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly re-
T
quires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of
the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated
with high-performance lubricant. During shipping, some lubricant may be transferred to the top of the walking belt
r the shipping carton. This is normal and does not affect treadmill performance. If there is lubricant on top of the
o
walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver and
adjustable wrench .
For help identifying the assembly hardware, see the drawings below. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it has
been preassembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included.
1. Make sure that the power cord is unplugged.
Locate the cardboard stand. With the help of a
second person, raise the front of the treadmill
and insert the crossbar on the Base (115) into
the cutout in the cardboard stand as shown.
Serious injury may occur if the treadmill
moves forward or backward and falls off the
cardboard stand. A second person must
hold the treadmill until assembly step 3 is
completed to prevent the treadmill from
moving, tipping, or falling.
1
7
115
Cardboard
Stand
2. Have a second person hold the Right Upright
(88) near the Right Base Cover (117). See the
inset drawing. Locate the wire tie in the rectan-
ular hole in the bottom of the Right Upright. Tie
g
the wire tie securely around the end of the
pright Wire (86). Then, pull the other end of the
U
wire tie until the Upright Wire is routed completely through the Right Upright.
Gently pull up on the Upright Wire (86) as you
set the Right Upright (88) on the Base (115) inside the Right Base Cover (117). Be careful not
to pinch the Upright Wire.
2
86
88
88
Wire
ie
T
86
Wire
Tie
Attach the Right Upright (88) to the Base (115)
with two 3/8" x 3 3/4" Patch Bolts (2) and two
3/8" Star Washers (8); do not fully tighten the
Patch Bolts yet. Note: It may be necessary to
tip the top of the Right Upright forward slightly
and rotate the bottom as you thread the Patch
Bolts into the Right Upright.
3. Have a seond person hold the Left Upright (85)
near the Left Base Cover (118). See the inset
drawing. Locate the wire tie in the rectangular
hole in the bottom of the Left Upright.Tie the wire
tie in the Left Upright securely around the end of
the 50" TV Cable (81) and the 50" A/V Wire
(80).
Then, pull the other end of the wire tie until the
50" TV Cable (81) and the 50" A/V Wire (80) are
routed completely through the Left Upright (85)
Gently pull up on the wires as you set the Left
Upright on the Base (115) inside the Left Base
Cover (118). Be careful not to pinch the
wires.
115
117
8
2
3
80
Wire
Tie
81
85
85
80
Wire
Tie
115
81
Attach the Left Upright (85) to the Base (115)
with two 3/8" x 3 3/4" Patch Bolts (2) and two
3/8" Star Washers (8); do not fully tighten the
Patch Bolts yet. Note: It may be necessary to
tip the top of the Left Upright forward slightly
and rotate the bottom as you thread the Patch
Bolts into the Left Upright.
With the help of a second person, lower the
treadmill off the cardboard stand. The stand will
be used again in assembly step 8.
118
8
2
Cardboard
Stand
8
4. Set the console assembly face down on a soft
surface to avoid scratching the console assembly.
4
17
17
Identify the Left Accessory Tray (90) and the
Right Accessory Tray (100).
Attach the Left Accessory Tray (90) and the
ight Accessory Tray (100) to the console as-
R
sembly with eight #8 x 1/2" Screws (17).
5. With the help of a second person, hold the console assembly near the Uprights (85, 88).
Connect the 50" A/V Wire (80) and the 50" TV
Cable (81) to the A/V wire and the 40" TV Cable
(141) extending from the console assembly.
Connect the Upright Wire (86) to the console
wire extending from the console assembly. See
the inset drawing. The connectors should
slide together easily and snap into place. If
they do not, turn one connector and try again. IF
THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.
Remove the wire tie from the Upright Wire (86).
Remove the wire tie from the 50" TV Cable (81)
and the 50" A/V Wire (80).
5
141
A/V
Wire
Wire
Tie
Console Wire
80
81
90
86
100
Console
Assembly
85
Console
Assembly
Console
Wire
86
88
Wire
Tie
9
. Insert the wires from step 5 into the Uprights
6
(85, 88) as you set the console assembly on the
Uprights. Be careful not to pinch any wires.
ttach the console assembly with four 3/8" x
A
1 1/4" Patch Bolts (1) and four 3/8" Star
Washers (8). Start all four Bolts before tight-
ening any of them.
6
Console
Assembly
7. Attach the Right Bottom Handrail Cover (104)
and the Left Bottom Handrail Cover (106) to the
console assembly with four #8 x 3/4" Screws
(7).
85
106
8
1
8
1
Console
Assembly
8
1
88
8
1
7
7
8. Locate the cardboard stand used for step 1.
With the help of a second person, raise the
front of the treadmill and insert the crossbar on
the Base (115) into the cutout in the cardboard
stand as shown. Have the second person
hold the treadmill to prevent it from moving
forward or backward.
Firmly tighten the four 3/8" x 3 3/4" Patch Bolts
(2).
With the help of a second person, lower the
treadmill off the cardboard stand.
10
104
7
8
2
115
2
Cardboard
Stand
9. Orient the Storage Latch (78) so that the large
barrel and the Latch Knob (77) are in the positions shown.
Remove the tie from the upper end of the
Storage Latch (78). Attach the upper end of the
Storage Latch to the bracket on the Frame (61)
ith a 3/8" x 1 3/4" Bolt (5) and a 3/8" Nut (9).
w
9
1
6
Remove the tie from the lower end of the
Storage Latch (78). Keep the holes in the Latch
Cap (79) aligned with the holes in the Storage
Latch. Make sure to keep the Latch Cap in-
side the Storage Latch. Attach the Storage
Latch to the bracket on the Base (115) with a
3/8" x 2" Bolt (6) and a 3/8" Nut (9). Note: It may
be necessary to move the Frame back and forth
to align the Storage Latch with the bracket.
Lower the Frame (61) (see HOW TO LOWER
THE TREADMILL FOR USE on page 27).
10. Note the location of the 75 ohm terminal and the
audio/video input jack on the treadmill. For the
television to operate, an antenna or a CATV
cable must be connected to the 75 ohm terminal
or the 96" A/V Wire (101) must be connected to
the audio/video input jack (see page 13).
10
77
9
115
5
78
Large
Barrel
9
79
6
Audio/
Video
Input
Jack
75 Ohm
Terminal
101
11. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex keys
in a secure place; one of the hex keys is used to adjust the walking belt (see pages 29 and 30). To protect
the floor or carpet from damage, place a mat under the treadmill.
11
If you purchase the optional chest pulse sensor (see page 26), follow the steps below to install the receiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged.
Remove the indicated #8 x 1/2" Screw (17) from
the Pulse Receiver Cover (95) on the back of the
console assembly.
2. Next, hold the receiver so that the antenna is
oriented as shown. Peel the paper backing off
the pad on the bottom of the receiver. Press the
receiver onto the Pulse Receiver Cover (95) in
the location shown.
1
95
17
2
Receiver
Console
Assembly
Antenna
95
3. Connect the wire on the receiver to the wire extending from the console assembly. Make sure
that no wires are pinched. Reattach the Pulse
Receiver Cover (95) to the console assembly
with the #8 x 1/2" Screw (17). Discard the other
wires included with the receiver.
3
Wires
Console
95
17
Assembly
12
Loading...