HEALTHCARE CR 10-X User Manual

HEALTHCARE

Imaging Services

Document No: DD+DIS205.12E

This number is needed for production line only: A604725.1

Enclosure

CR 10-X

Type 5151 / 100

Replacement Instructions for the

"PMT with Light Collector"

► Purpose of this Document

This enclosure is part of the spare part kit "PMT with Light Collector", spare part number*: CM+6040420

It describes all necessary steps for the replacement.

* The last digit in the spare part number indicates the spare part revision at release of this document. When ordering, the actual revision of the spare part is delivered.

► Referenced Documents

Document Title

None

NOTE:

Revision 0 09-2012 printed in Germany

Agfa Company Confidential

Dispose the enclosure document after finishing your task (observe the confidentiality note below).

Use, dissemination, distribution or reproduction of this document by unauthorized personnel is not permitted and may be unlawful.

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled.

CONFIDENTIALITY NOTE:

DOCUMENT CONTROL NOTE:

Document Node ID: 33997185

Enclosure_e_template_v07

DD+DIS205

.12E

► Manufacturer

Agfa HealthCare N.V.

Publisher

Agfa-Gevaert HealthCare GmbH Tegernseer Landstraße 161 D - 81539 München Germany

Agfa and the Agfa rhombus are trademarks of Agfa-Gevaert N.V., Belgium, or its affiliates.

Enclosure

WARNING:

Improper operation or service activities may cause damage or injuries.

INSTRUCTION:

(1) Read the "Generic Safety Directions" document

(see Agfa HealthCare Library => General Info => Agfa HealthCare => Publications => Service Manual) prior to attempting any operation, repair or maintenance task on the equipment.

(2) Strictly observe all safety directions within the "Generic Safety Directions" and on

the product.

CAUTION:

Static discharge! Electrical components may be destroyed:

For the repair on electrical components, wear a grounding strap (Order number: CM+9 9999 0830 0) around the wrist and connect the other end of this strap on a grounded conducting metal piece.

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled.

Revision 0 CR 10-X Page 2 of 16 09-2012 Type 5151 / 100 Agfa Company Confidential

DOCUMENT CONTROL NOTE:

DD+DIS205

.12E

Enclosure

LIST OF CONTENTS

REPLACING THE PMT WITH LIGHT COLLECTOR ...............................................................6

2 PERFORMING A SOFTWARE UPDATE IF CURRENT SOFTWARE < ARC_1302 .............10

3 PERFORMING A SHADING CALIBRATION..........................................................................11

3.1 Checking and Erasing the Image Plate ..................................................................................11

3.2 Exposing the Cassette ............................................................................................................12

3.3 Scanning the Image Plate.......................................................................................................13

3.4 Verifying a successful Shading Calibration.............................................................................15

3.5 Appendix: Possible Reasons for a failed Shading Calibration................................................16

4 VERIFYING THE REPLACEMENT ........................................................................................16

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled.

Revision 0 CR 10-X Page 3 of 16 09-2012 Type 5151 / 100 Agfa Company Confidential

DOCUMENT CONTROL NOTE:

DD+DIS205

Subject

.12E

Replacement Instructions "PMT with Light Collector"

SCOPE OF DELIVERY:

REQUIRED TOOLS:

Enclosure

Figure 1

TX20

1,5 mm Copper Filter** Spare part number*: CM+9 5155 1015 2

Polynit wipes***

Spare Part Number*:

10+9 9999 1273 0

CR Phosphor Plate Cleaner***

Spare part number*:

10+9 9999 1197 0

Lint free cloth**

* The last digit in the spare part number indicates the spare part revision at release of this document. When ordering, the actual revision of the spare part is delivered.

** The Cu filter is part of digitizer delivery.

*** For cleaning of an image plate either use Polynit wipes or CR Phosphor plate cleaner and a lint free cloth.

REQUIRED SOFTWARE:

The PMT with Light Collector which is part of delivery requires software ≥ ARC_1302.

REQUIRED TIME:

Approximately 55 minutes

 20 minutes exchange

 15 minutes software update (if required)

 20 minutes shading calibration including verification

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled.

Revision 0 CR 10-X Page 4 of 16 09-2012 Type 5151 / 100 Agfa Company Confidential

DOCUMENT CONTROL NOTE:

DD+DIS205

.12E

Enclosure

CAUTION:

The PMT light sensitivity decreases for a certain time (hours to days) if exposed to bright light.

Expose the light sensitive side of the PMT as little as possible to daylight.

CAUTION:

The Light Collector can break when mechanically stressed.

Handle the Light Collector with great care.

CAUTION:

Finger prints on the mirror before the Light Collector may cause reduced image quality.

Be careful not to touch the mirror.

Mirror before Light Collector

515131ak.cdr

Figure 2

The controlled version of this document is available from the Agfa HealthCare Library. Any printed copy of this document is uncontrolled.

Revision 0 CR 10-X Page 5 of 16 09-2012 Type 5151 / 100 Agfa Company Confidential

DOCUMENT CONTROL NOTE:

+ 11 hidden pages