Page 1
Operating Instructions
HDMI Extender over CAT5 with Bi-Directional IR
HDMI Extender over single Cat5e/6 cable
With Loop HDMI Output
i
Page 2
Operating Instructions
HDMI Extender over single Cat5e/6 cable
With Loop HDMI Output
Operating instruction
HDMI Extender over single Cat5e/6 cable
with Loop HDMI Output
Dear Cust omer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
connecting,
otice
N
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Features
operating or adjusting this product. Please keep this manual for future reference.
The information in this document is subject to change without notice. Every effort has been made in the
Each set includes one transmitter and one receiver.
Transmit Over 50m single CAT5e/6 without signal loss.
Support 1xLoop HDMI output on the transmitter.
Support high definition resolution up to Full HD 1080p.
Support Dolby True-HD, DTS-HD Master audio.
EDID reading and saving from display.
With Bi-Direction wideband IR (38~56 kHz).
Support 3D.
1
Page 3
S pe c i f i c a ti o ns
Operating Instructions
Operating Temperature Range -5 to +35℃(+23 to +95 )
Operating Humidity Range 5 to 90%RH (No Condensation)
Data transfer speed 6.75Gbps
HDMI Receptacle x 2 (1xHDMI input, 1xHDMI loop output)
Connectors on Transmitter
Connectors on Receiver
Resolution outputs 1080p/1080i/720p/576p/480p
Audio format supported DTS-HD Master Audio, Dolby True HD, multi-channel 5.1, stereo etc
Output Video Signal
RJ45 Receptacle x 1
Power DC Receptacle x 1
IR Receptacle x 2(for IR TX and RX cable)
HDMI Receptacle x 1
RJ45 Receptacle x 1
Power DC Receptacle x 1
IR Receptacle x 2(for IR TX and RX cable)
HDMI
℉
Dimension (L×W×H)
Power supply DC 5V Power supply
Power consumption 3.5W(MAX)
Transmission Distance 1080p up to 50m
Net Weight 480g (1 Pair)
IR wavelength & frequency Wavelength: 940nm IR Frequency: 38KHz - 56KHz
1.Under perfect transmission conditions including straight cable runs with no electrical interference, bends,
Note:
kinks, patch panels or wall outlets.
TX: L127.1xW70.6xH28.2mm
RX: L85xW65xH24mm
(1)
Package Contents
1xHDMI Transmitter
1xHDMI Receiver
2 x IR TX Emitter
2x IR RX Receiver
2x5V/1A DC Adapter
1xUser Manual
2
Page 4
Panel Description
Operating Instructions
Transmitter Panel
1 .
HDMI Output.
2 . EDID copy button.
3 . Status of power input. When power input on, the LED lights.
4 . Status of signal connection. When this works well, the LED lights.
5 . CAT-5E/6 output.
6 . IR TX.
7 . IR RX.
8 . HDMI Input.
9 . Power input, 5VDC.
Note1:
When the sink can’t display the signal, try to connect HDMI output port of the transmitter to the display
device. Plug the power supply into Transmitter, press the “EDID copy button” and the light flashes, the
EDID data has been copied from the display device successfully, at least press ”EDID copy button” for
3 seconds, The EDID will be reset to the default setting.
HDMI Output
RXTX
(1)
Note2:
The distance is 40m under 5.1CH or 7.1CH.
Receiver Panel
RXTX
HDMI Extender over single Cat5e/6 cable
1 . Status of signal connection. When this works well, the LED lights
2 . Status of power input. When power input on, the LED lights
3 . CAT-5E/6 input
4 . IR TX
5 . IR RX
6 . HDMI output
7 .
Power input, 5VDC.
3
Page 5
Connection Diagram
HDMI Cable
Cat5e/6 Cable
Operating Instructions
Transmitter
HDMI Source
PS3,Blu-ray DVD player, etc.
HDMI In
Cat5e/6 x1
HDMI Extender over single Cat5e/6 cable
with Loop HDMI Output
IR-TX
IR-RX
TV remote
Receiver
Loop HDMI Out
3D TV
HDMI Out
3D TV
IR-TX
IR-RX
DVD or STB remote
Connections and Operations :
1.Connect 1 source such as a Blu-Ray Player, game console, STB, etc. to the HDMI input on the transmitter
2.Connect 1 display such as an HDTV or HD Projrctor to the Loop HDMI output on the transmitter.
3.Con
nect 1 display such as an HDTV or HD Projector to the HDMI output on the receiver
4.Connect a single Category 5e/6/7 up to (50m) to both transmitter and receiver.
5.Plug in the IR-RX cable and IR-TX cable to the IR jack port located on the Receiver and transmitter balun.
6. Power on the transmitter and receiver firstly, then power on the source and sink.
.
4
Page 6
Operating Instructions
Safety information
safeguards
To reduce the risk of electric shock, do not expose this product to rain or moisture
PRODUCT SERVICE
1) Damage requiring service: The unit should be serviced by qualified service personnel if:
(a)The DC power supply cord or AC adaptor has been damaged;
(b)Objects or liquids have gotten into the unit;
(c)The unit has been exposed to rain;
(d)The unit does not operate normally or exhibits a marked change in performance;
(e)The unit has been dropped or the cabinet damaged.
2) S
ervicing Personnel: Do not attempt to service the unit beyond that described in these operating instructions.
Refer all other servicing to authorized servicing personnel.
3) R
eplacement parts: When parts need replacing ensure the servicer uses parts specified by the manufacturer or
parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric
shock, or other hazards.
4) S
afety check: After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in
proper working condition.
WARRANTY
If your product does not work properly because of a defect in materials or workmanship, our Company (referred to
as "the warrantor" ) will , for the length of the period indicated as below, (
starts with the date of original purchase ("Limited Warranty period"), at its option either(a) repair your product with
new or refurbished parts, or (b) replace it with a new of a refurbished product. The decision to repair or replace will
be made by the warrantor.
During the "Labor" Limited Warranty period there will be no charge for labor.
During the "Parts" warranty period, there will be no charge for parts. You must mail-in your product during the
warranty period. This Limited Warranty is extended only to the original purchaser and only covers product
purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty
service.
Parts(2)Year ,Labor(90) Days) which
1
M
ail-In Service
When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original carton.
Include a letter detailing the complaint and provide a day time phone and/or email address where you can be
reached.
5
Page 7
Operating Instructions
LIMITED WARRANTY LIMITS AND EXCLUSIONS
1) This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages
which occurred in shipment, or failures which are caused by products not supplied by warrantor,or failures which
result from accidents,misuse,abuse,neglect, mishandling, misapplication, alteration, faulty installation, set-up
adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage,
modification, or service by anyone other than a Factory Service center or other Authorized Servicer, or damage
that is attributable to acts of God.
2) THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER "LIMITED WARRANTY
COVERAGE".THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRNTY.
(As examples, this excludes damages for lost time, cost
applicable, travel to and from the service, loss of or damage to media or images, data or other recorded content.
The items listed are not exclusive, but are for illustration only.)
3) PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR
RESPONSIBILITY.
of having someone remove or re-install an installed unit if
6
Loading...