HDMI IMB-1222, IMB-1222-WV, IMB-1223, IMB-1223-WV, IMB-X1222-WV User Manual

*15G06M090000AK*

P/ N: 15G06M090000AK V1.0

Jumpers and Headers Setting Guide

IMB-1222

IMB-1222-WV

IMB-1223

IMB-1223-WV

IMB-X1222-WV

The terms HDMI® and HDMI High-Definition

Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

			Vbus
1	: USB3.2 Gen1 Header	Vbus	IntA_PB_SSRX-
		IntA_PA_SSRX-	IntA_PB_SSRX+
	(USB3_3_4)	IntA_PA_SSRX+	GND
		IntA_PA_SSTX-	IntA_PB_SSTX+
		GND	IntA_PB_SSTX-
		IntA_PA_SSTX+	GND
2	: Battery Connector	GND	IntA_PB_D-
		IntA_PA_D+	Dummy
4	: MCU Connector	IntA_PA_D-	IntA_PB_D+
		1
5	: LPC Header (For IMB-1222 / IMB-1222-WV
	/ IMB-X1222-WV Only)	<![if ! IE]> <![endif]>GND SMB CLK MAIN	<![if ! IE]> <![endif]>SMB DATA MAIN			<![if ! IE]> <![endif]>GND S PWRDWN#
6	: SATA3 Connectors			<![if ! IE]> <![endif]>LAD2	<![if ! IE]> <![endif]>LAD1		<![if ! IE]> <![endif]>SERIRQ# GND
	(SATA3_1, SATA3_2)	1
		<![if ! IE]> <![endif]>PCICLK FRAME	<![if ! IE]> <![endif]>PCIRST#	<![if ! IE]> <![endif]>LAD3	<![if ! IE]> <![endif]>+3V	<![if ! IE]> <![endif]>LAD0	<![if ! IE]> <![endif]>+3VSB	<![if ! IE]> <![endif]>GND

7 : Digital Input / Output Default Value

Setting (JGPIO_SET1)

1-2: Pull-High

2-3: Pull-Low

8 : Digital Input / Output Power Select

(JGPIO_PWR1)

1-2: +12V

2-3: +5V

9 : Digital Input/Output Pin

Header (JGPIO1)

	PIN	Signal	PIN	Signal	PIN	Signal	PIN	Signal	PIN	Signal
		Name		Name		Name		Name		Name
	2	SIO_	4	SIO_	6	SIO_	8	SIO_	10	GND
		GP71		GP72		GP73		GP74
	1	SIO_	3	SIO_	5	SIO_	7	SIO_	9	JGPIO_
		GP75		GP76		GP77		GP80		PWR

10 : COM Port Headers							1
	(COM1, 2, 3, 4)
							2
PIN	Signal	PIN	Signal	PIN	Signal	PIN		Signal	PIN	Signal
	Name		Name		Name			Name		Name
1	DDCD#	3	TTXD	5	GND	7		RRTS#	9	PWR
2	RRXD	4	DDTR#	6	DDSR#	8		CCTS#

* This motherboard supports RS232/422/485 on COM1, 2 ports.

Please refer to below table for the pin definition. In addition, COM1, 2 ports (RS232/422/485) can be adjusted in BIOS setup utility >

Advanced Screen > Super IO Configuration. You may refer to our user manual for details.

COM1, 2 Port Pin Definition

PIN	RS232	RS422	RS485
1	DCD	TX-	RTX-
2	RXD	RX+	N/A
3	TXD	TX+	RTX+
4	DTR	RX-	N/A
5	GND	GND	GND
6	DSR	N/A	N/A
7	RTS	N/A	N/A
8	CTS	N/A	N/A
9	PWR	PWR	PWR

11 : COM Port PWR Setting Jumpers PWR_COM1 (For COM Port1)

PWR_COM2 (For COM Port2)

PWR_COM3 (For COM Port3) PWR_COM4 (For COM Port4) 1-2: +5V

2-3: +12V

																					PIN	Signal Name
																					1	NA
																					2	GND
																					3	eDP_TX#3_CON
																					4	eDP_TX3_CON
																					5	GND
																					6	eDP_TX#2_CON
																					7	eDP_TX2_CON
																					8	GND
																					9	eDP_TX#1_CON
																					10	eDP_TX1_CON
																					11	GND
																					12	eDP_TX#0_CON
																					13	eDP_TX0_CON
																					14	GND
																					15	eDP_AUX_CON
																					16	eDP_AUX#_CON
																					17	GND
																					18	LCD_VCC
																					19	LCD_VCC
																					20	LCD_VCC
																					21	LCD_VCC
																					22	NA
																					23	GND
																					24	GND
																					25	GND
																					26	GND
																					27	eDP_HPD_CON
																					28	GND
																					29	GND
40																					30	GND
																					31	GND
																		<![if ! IE]> <![endif]>EDP1			32	CON_LBKLT_EN
																					33	CON_LBKLT_CTL
* eDP Connector (on the																					34	SMB_DATA
																					36	LCD_BLT_VCC
																					35	SMB_CLK
Backside of PCB)
																					37	LCD_BLT_VCC
1																					38	LCD_BLT_VCC
15 : Backlight Control Level																					39	LCD_BLT_VCC
																					40	NA

(CON_LBKLT_CTL) (BLT_PWM1)

1-2: From eDP PWM to

CON_LBKLT_CTL

2-3: From LVDS PWM to

CON_LBKLT_CTL

16 : Panel Power Select (LCD_VCC) (PNL_PWR1)

1-2: LCD_VCC: +3V 2-3: LCD_VCC: +5V

4-5: LCD_VCC: +12V

12 : Backlight Power Select

17 : Backlight Volume Control (BLT_VOL1)

(LCD_BLT_VCC) (BKT_PWR1)

1-2: LCD_BLT_VCC: +5V

1

2-3: LCD_BLT_VCC: +12V

PIN

Signal

PIN

Signal

PIN

Signal

PIN

Signal

PIN

Signal

PIN

Signal

PIN

Signal

4-5: LCD_BLT_VCC: DC_IN

Name

Name

Name

Name

Name

GPIO_

GPIO_

Name

Name

7

GND

6

GND

5

BLT_DW

4

BLT_UP

3

PWRDN

2

VOL_DW

1

VOL_UP

13 : Inverter Power Control Wafer

	(BLT_PWR1)				PIN			Signal Name
					6			LCD_BLT_VCC
14* : LVDS Panel					5			LCD_BLT_VCC
					4		CON_LBKLT_EN
	Connector
					3		CON_LBKLT_CTL
					2			GND
PIN	Signal Name	PIN	Signal Name		1			GND
39	LCD_BLT_VCC	40	LCD_BLT_VCC							1
37	CON_LBKLT_CTL	38	LCD_BLT_VCC
35	GND	36	CON_LBKLT_EN
33	LVDS_B_CLK#	34	LVDS_B_CLK			39		40
31	LVDS_B_DATA3	32	GND
29	DPLVDD_EN	30	LVDS_B_DATA3#
27	LVDS_B_DATA2#	28	LVDS_B_DATA2
25	LVDS_B_DATA1	26	GND
23	GND	24	LVDS_B_DATA1#
21	LVDS_B_DATA0#	22	LVDS_B_DATA0
19	LVDS_A_CLK	20	GND
17	GND	18	LVDS_A_CLK#
15	LVDS_A_DATA3#	16	LVDS_A_DATA3
13	LVDS_A_DATA2	14	GND			1		2
11	GND	12	LVDS_A_DATA2#		* PD (Panel Detection): Connect this
9	LVDS_A_DATA1#	10	LVDS_A_DATA1
7	LVDS_A_DATA0	8	PD (Panel Detection)			pin to LVDS Panel’s Ground pin to
5	LDDC_DATA	6	LVDS_A_DATA0#			detect Panel detection.
3	+3.3V	4	LDDC_CLK
1	LCD_VCC	2	LCD_VCC

18 : SATA Power Output Connector	<![if ! IE]> <![endif]>1
	<![if ! IE]> <![endif]>+5V
19 : USB2.0 Headers	<![if ! IE]> <![endif]>GND
(USB2_11_12, USB2_8_9)

(USB2_11_12 is for IMB-1222 / IMB-1222-WV / IMB-X1222-WV Only)

20 : CPU FAN Connector (+12V)

FAN_SPEED_CONTROL	4
FAN_SPEED	3
+12V	2
GND	1

<![if ! IE]>

<![endif]>+12V GND

21 : System Panel Header

34 : SPDIF Header

PLED-

+5V

PLED+

PWRBTN#

GND

22 : SMBUS_TEST1

1

35 : DC Jack (DC_JACK1)

RESET#

GND

36 : Audio Jack: Pink - Mic In

HDLED+

GND

HDLED-

38 : Audio Jack: Green - Line Out

37 : Front Panel Audio Header

23 : Chassis Intrusion Header (CI1) 1

Close: Active Case Open

OUT_RET

OUT2_L

GND

Open: Normal

Signal

MIC_RET

J_SENSE

OUT2_R

24 : Clear CMOS Header (CLRMOS1)

PRESENCE#

MIC2_R

GND

MIC2_L

1-2: Normal

1

2-3: Clear CMOS

39 : 3W Audio AMP Output Wafer

PIN

Signal Name

25 : SIO_AT1

4

OUTRN

Open: ATX Mode

3

OUTRP

2

OUTLP

Short: AT Mode

1

1

OUTLN

26 : Chassis FAN Connector FAN_SPEED_CONTROL

(+12V)

CHA_FAN_SPEED

40 : RJ45 LAN Port (LAN2)

+12V

27 : EDP_LVDS_SWITCH1

GND

42 : RJ45 LAN Port (LAN1)

41 : VGA Header

Open: LVDS

Short: EDP

(For IMB-1223 / IMB-1223-WV Only)

28 : AC PWR LOSS Header

PIN

Signal Name

PIN

Signal Name

9

DDC_CLK

10

DDC_DATA

(AC_PWR_LOSS1)

7

HSYNC

8

VSYNC

Short: AC Power Loss

5

BLUE

6

GND

3

GREEN

4

GND

Open: no AC Power Loss

1

1

RED

2

GND

Installation of ROM Socket

*Do not apply force to the actuator cover after ic inserted.

*Do not apply force to actuator cover when it is opening over 120 degree, Otherwise, the actuator cover may be broken.

*The yellow dot (Pin1) on the ROM must be installed at pin1 position of the socket (white arrow area).

*Make sure the white dot on the ROM is installed outwards of the socket.

*For further details of how to install ROM, please refer to ASRI website.

Warning: If the installation does not follow as the picture, then it may cause severe damage to chipset & MB.

M.2 Socket Pin Definition

3 : M.2 Key-B Socket (M2_KEYB1)

29 : M.2 Key-M Socket (M2_KEYM1)

30 : M.2 Key-E Socket (M2_KEYE1)

31 : Power Adapter

1

43 : DisplayPort (DISPLAY3) (For IMB-1222 /

PIN

Signal Name

(For IMB-1222-WV /

IMB-1222-WV / IMB-X1222-WV Only)

1

GND

IMB-X1222-WV Only)

2

5VA_CONTROL

3

5VA

44 : ThunderBolt Header

4

GND

PIN

Signal Name

5

GND

32 : 4-pin ATX PWR Connector

3

4

TBT_SLP_S5_S4#

4

3

SLP_S3#

1-2: GND

2

TBCIO_PLUG_EVENT

3-4: DC Input

1

2

1

1

TB_FRC_PWR

45 : Top: DisplayPort (DP2)

33 : 2-pin UPS Module Power Input

Connector

Bottom: HDMI Port (HDMI1)

Pin1: GND

1

46 : USB3.2 Gen1 Ports (USB_5_6) (IMB-1222

Pin2: DC Input

/ IMB-1222-WV / IMB-X1222-WV)

USB2.0 Ports (USB_5_6) (IMB-1223 /

IMB-1223-WV)

47 : USB3.2 Gen1 Ports (USB3_1_2)

Back Side :

SIM Card Socket (SIM1) (For IMB-1222-

WV / IMB-X1222-WV / IMB-1223-WV

Only)

eDP Connector (EDP1, refer to No. 14)