HD Communications HD28650 User Manual

HD COM

IN WALL BOX ACCESS POINT

Model :

HD28650

Copyright Notice

Copyright © 2005-2015 HD COM Technologies Inc. All rights reserved. No part of this document may
be copied, reproduced, or transmitted by any means, for any purpose without prior written permission.
Protected by TW patent 223184, JPN patent 3099924 and China patent ZL 03 2 04640.5.

Disclaimer

We shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from furnishing this material, or the performance or use of this
product. We reserve the right to change the product specification without notice. Information in this
document may change without notice.

Trademarks

Microsoft Win98, Windows 2000 and WinXP are registered trademarks of Microsoft Corporation.

General: All other brand and product names mentioned herein may be registered trademarks of their
respective owners. Customers should ensure that their use of this product does not infringe upon any
patent rights. Trademarks mentioned in this publication are used for identification purposes only and
are properties of their respective companies.

2

In Wall Access Point

Table of Contents

1 Introduction------------------------------------------------------------------------------------------------------------5

1-1 Package Contents ---------------------------------------------------------------------------------------------------5
1-2 Features----------------------------------------------------------------------------------------------------------------6
1-3 Precautions------------------------------------------------------------------------------------------------------------6
1-4 Outlook------------------------------------------------------------------------------------------------------------------6

1-4-1 Top Panel ----------------------------------------------------------------------------------------------------6
1-4-2 Rear Panel---------------------------------------------------------------------------------------------------7

1-5 Technical Specifications -------------------------------------------------------------------------------------------7

1-5-1 Hardware Specifications ---------------------------------------------------------------------------------7
1-5-2 Software Specifications ----------------------------------------------------------------------------------8

2 Installation -------------------------------------------------------------------------------------------------------------9

2-1 Installation Requirements----------------------------------------------------------------------------------------10
2-2 Getting Start---------------------------------------------------------------------------------------------------------12

3 Configuring the In Wall Access Point -----------------------------------------------------------------------------16
3-1 Internet Setting -----------------------------------------------------------------------------------------------------18

3-1-1 TCP/IP Setting--------------------------------------------------------------------------------------------18

3-2 Wireless --------------------------------------------------------------------------------------------------------------20

3-2-1 Wireless Basic Setting----------------------------------------------------------------------------------20
3-2-2 Wireless Advanced Setting----------------------------------------------------------------------------21
3-2-3 Wireless Security Setting ------------------------------------------------------------------------------22

3-3 Advanced ------------------------------------------------------------------------------------------------------------25

3-3-1 Management----------------------------------------------------------------------------------------------25
3-3-2 Firmware ---------------------------------------------------------------------------------------------------27
3-3-3 Configuration----------------------------------------------------------------------------------------------29
3-3-4 SNMP-------------------------------------------------------------------------------------------------------31
3-3-5 System------------------------------------------------------------------------------------------------------32
3-3-6 Ping Command-------------------------------------------------------------------------------------------32

In Wall Access Point

3

3-4

Advanced ------------------------------------------------------------------------------------------------------------32

3-4-1 Restart------------------------------------------------------------------------------------------------------32
3-4-2 Logout ------------------------------------------------------------------------------------------------------34

Appendix A Signal Connection Arrangements--------------------------------------------------------------------34
Appendix B Regulations/EMI Compliance -------------------------------------------------------------------------35
LIMITED WARRANTY---------------------------------------------------------------------------------------------------36

4

In Wall Access Point

1 Introduction

The HD28650 Access Device revolutionizes the way wireless and wired IP-based services are
delivered to hospitality and residential properties. The HD28650 integrates wired and wireless
connectivity into a small unit that can be quickly and discretely installed in a standard wall box. The
HD28650 provides One Ethernet ports, a 2.4GHz 802.11b/g/n wireless access point. The HD28650
requires a single powered cable drop to unlock its utility and, through the reduction in cabling, switch
ports, and power-sourcing equipment, the HD28650 represents the best value for the delivery of next
generation entertainment services.

1-1 Package Contents

Please inspect your package. The following items should be included:

◎ HD28650

 One In Wall Access Pointt
 One Telephone Cable (10cm)
 One UTP Ethernet/Fast Ethernet cable (Cat.5 Twisted-pair)
 One Wall Faceplate(Top and Bottom )
 Bracket (EU STD*2/Set JPN STD*1/Set)
 One Quick Installation Guide

If any of the above items are damaged or missing, please contact your dealer immediately.

In Wall Access Point

5

1-2 Features

 Wireless data rates up to 150Mbps
 Comprehensive security

64/128-bit WEP encryption
WPA encryption
WPA2 encryption

 Intelligent Management

1-3 Precautions

 Never remove or open the cover. You may suffer serious injury if you touch these parts.
 Never install the system in the wet locations.

Outlook

1-4

Figure 1 In Wall Box Access PointOutlook

1-4-1 Top Panel

The top panel of the In Wall Box Access Pointis shown below.

Figure 2 In Wall Box Access PointTop Panel

LEDs Indication

LED State Description

Off The In Wall Box Access Pointis not receiving electrical power. PWR
Green The In Wall Box Access Pointis receiving electrical power.

SYS

LINK / WAN

LAN

WLAN

Off The In Wall Box Access Pointstatus is defective.
Green The In Wall Box Access Pointstatus is complete.
Green (Blinking) During firmware upgrades, this system LED will blink.
Off Port has not established any network connection.
Yellow A port has established a valid 10/100Mbps network connection.
Yellow (Blinking) 10/100Mbps traffic is traversing the port.
Off Port has not established any network connection.
Green A port has established a valid 10/100Mbps network connection.
Green (Blinking) 10/100Mbps traffic is traversing the port.
Off The Wireless is not ready.
Green The In Wall Box Access Pointhas established a valid wireless connection.
Green (Blinking) The Wireless connection is active.

6

In Wall Access Point

1-4-2 Rear Panel

The rear panel of the In Wall Access Pointt

Figure 3 In Wall Box Access PointRear Panel

1-5 Technical Specifications

1. RJ-11 Telephone Connector

2. RJ-45 Ethernet Connector

3. WPS Button

4. Reset Button

5. WLAN

6. SYSTEM

7. POWER

8. LAN Port

9. LINK Port

1-5-1 Hardware Specifications
Network Specification

IEEE802.3 10 Base TX Ethernet
IEEE802.3u 100 Base TX Fast Ethernet
IEEE802.3af Power over Ethernet
IEEE802.11b Wireless LAN
IEEE802.11g Wireless LAN
IEEE802.11n Wireless LAN
ANSI/IEEE 802.3 NWay auto-negotiation
Static IP Client
DHCP Client
Wi-Fi Compatible

Connectors

One LAN Ports (10BaseT/100BaseTX Auto cross-over)

In Wall Access Point

7

One LINK Port (10BaseT/100BaseTX Auto cross-over)
Two Tel Port (Telephone Line transparent used)

Encryption

WEP (Wired Equivalent Privacy) 64/128-bit RC4
WPA (Wi-Fi Protected Access)
WPA2 (Wi-Fi Protected Access)
WPS (Wi-Fi Protected Setup)

LED Indicators

One POWER LED
One Link 10/100M Link/Activity LED
One LAN 10M/100M Link/Activity LEDs
One Wireless Link/Activity LED
One System LED

Environment Conditions

Operating Temperature: 0 to 50°C
Storage Temperature: -10 to 60°C
Operating Humidity: 10~80% non-condensing
Storage Humidity: 10% to 90% non-condensing

Certifications

FCC part 15 Class B, CE, NCC

Dimension

Size: 39.3(W) x 71.6(L)x 55(H)/ mm
Weight: About 85g (Net)

1-5-2 Software Specifications

Networking

• IEEE802.3 10BaseT Ethernet

• IEEE802.3u 100BaseTX Fast Ethernet

• IEEE802.3af Power over Ethernet

• IEEE802.11b Wireless LAN

8

In Wall Access Point

• IEEE802.11g Wireless LAN

• IEEE802.11n Wireless LAN

• Static IP WAN Client

• DHCP WAN Client

Security and Firewall

• WEP

• WPA

• WPA2

• WPS

Management

• Web-based Management Tool

• Firmware Upgrade via HTTP/TFTP

• Backup/Restore/Factory Default Setting

• Remote Authorized Management

• SNMP v1/v2 (MIB II, Private MIB)

• System Information Table

2 Installation

The followings are instructions for setting up the In Wall Access Point. Refer to the illustration and
follow the simple steps below to quickly install your In Wall Access Point.

Step 1：Slide the Bracket to align with screw holes on the HD28650, and fasten the Bracket tightly with

screws on the HD28650.

In Wall Access Point

9

Step 2：Slide the HD28650 into the Bottom Faceplate and fasten tightly into the Bottom Faceplate until

it’s flushed into the wall.

Step 3：Line-up and push the Top faceplate onto Bottom faceplate until snaps securely into place.

2-1 Installation Requirements

Before installing the In Wall Access Point, make sure your network meets the following
requirements.

System Requirements

10

In Wall Access Point

The In Wall Box Access Pointrequires one of the following types of software:

 Windows 98 Second Edition/NT/2000/XP
 Red Hat Linux 7.3 or later version
 MAC OS X 10.2.4 or later version
 Any TCP/IP-enabled systems like Mac OS and UNIX (TCP/IP protocol installed)
 Standard phone line for xDSL modem

Or
Coaxial cable for Cable modem
 Web Browser Software (Microsoft I.E 5.0 or later version or Netscape Navigator 5.0 or later

version)

 One computer with an installed 10Mbps, 100Mbps or 10/100Mbps Ethernet card
 UTP network Cable with a RJ-45 connection (Package contents)

Note: Prepare twisted-pair cables with RJ-45 plugs. Use Cat.5 cable for all connections. Make sure

each cable not exceed 328 feet (Approximately 100 meters).

In Wall Access Point

11

2-2 Getting Start

HD28650 support web-based configuration. Upon the completion of hardware installation, can be
configured through PC/NB by web browser such as Internet Explorer, Firefox, and Opera.

 Default IP Address:10.59.1.254
 Default Subnet Mask:255.255.255.0
 Default Username and Password: admin/admin

：

Set the IP segment of the administrator’s computer to be in the same range as HD28650 for

Note

accessing the system. Do not duplicate the IP address used here with IP address of HD28650 or
any other device within the network

Step1：Click StartSettingControl Panel, and then “Control Panel” window appears, Click on
“Network connection” window appears.

.

Step2：In “Local Area Connection properties” window, select “Internet Protocol (TCP/IPv4)” and
click on “properties” button.

12

In Wall Access Point

Step 3：Launch your browser, and then enter the factory default IP address 10.59.1.254 in your
browser’s location box. Press Enter.

Example:
IP Address:10.59.1.109

Subnet Mask:255.255.255.0

Step 4：.The HD28650 login screen will appear. In the Username and Password field, type the factory

default user name admin and password admin and click Setup. The HD28650 setup screen will
appear.

In Wall Access Point

13

HD28650

It is important to remember your password. If for any reason you lose or forget your password, press the reset

Note:

button located on the top of the device. Reset action will re-initialize the settings. All configurations, including
username, password and IP address(s), will be reset, and requires re-entering.

POE (Power over Ethernet) Application

14

In Wall Access Point

Note: To use the HD28650’s POE feature, follow the instructions for your specific POE device.

In Wall Access Point

15

3 Configuring the In Wall Access Point

Step 1: Start your browser, and then enter the factory default IP address 10.59.1.254 in your browser’s

location box. Press Enter.

Figure 4 Web Browser Location Field (Factory Default)

Step 2: The In Wall Box Access Pointconfiguration tools menu will appear. In the Username and

Password field, type the factory default user name admin and password admin and click
Login. If you are first time setting the system, the wizard setup screen will appear. You will be
guided, step-by-step, through a basic setup procedure.

Username: admin
Password: admin

Figure 5 Configuration Tools Menu

Note:



This Web agent is best viewed with IE 5.0 or Netscape 6.0 and above browsers.



Username and Password can consist of up to 20 alphanumeric characters and are case sensitive.



If for some reason your password is lost or you cannot gain access to the In Wall Box Access

PointConfiguration Program, please press the reset button to load the device to manufacturer
defaults.



If the In Wall Box Access Pointdoesn’t send packet in 5 minutes (default), the In Wall Box Access
Pointwills logout automatically.

 Proxy needs to set disable first when administrator accesses admin UI

16

In Wall Access Point

The Setting enables you to configure advanced settings related to accessing the Internet；display In
Wall Box Access Pointbasic status and process Firmware upgrade, change password and backup or
restore configuration. Including,

 Internet Setting

 Link

 Wireless

 Basic
 Advanced
 Security
 WPS

 Administration

 Management
 Firmware
 Configuration
 SNMP
 System Status
 Ping Command

 System Tool

 Restart
 Logout

Figure 6 Configuration Tools Menu

In Wall Access Point

17

Internet Setting

3-1

3-1-1 TCP/IP Setting

The IP address can be manually set or automatically assigned by a DHCP server on the LAN. If you are
manually setting the IP address, Subnet mask, and Gateway IP address settings, set them
appropriately, so that they comply with your LAN environment.

Figure 7 the TCP/IP Setting

DHCP Client

The device can work as a DHCP client. This allows the device to obtain the IP address and other
TCP/IP settings from your switch or IP router. If your device comes with this feature, please enabl e
Use DHCP Client.

MTU Setting 1492 MTU (Maximum Transfer Unit) specifies maximum

18

Figure 8 DHCP Client Setting Screen

Item Default Description

In Wall Access Point

transmission unit size.

Static IP

Figure 9 Static IP Setting Screen

Item Description

IP Address 10.59.1.254 Enter the IP address for the xDSL/Cable connection (provided

by your ISP).
Subnet Mask 255.255.255.0 Enter the subnet mask for the IP address.
Gateway IP
Gateway
Primary DNS
Server
Secondary
DNS Server

MTU Setting 1492 MTU (Maximum Transfer Unit) specifies maximum

Enter the Gateway IP address for the xDSL/Cable connection

A primary DNS server IP address for the xDSL/Cable

connection

A secondary DNS server IP address for the xDSL/Cable

connection. If the primary DNS Server IP were not available,

meanwhile, Secondary DNS Server IP would start in the same

time.

transmission unit size.

In Wall Access Point

19

Wireless

3-2

3-2-1 Wireless Basic Setting

Figure 10 Wireless Basic Setting Screen

Item Default Description
General Settings

The ESSID is the unique name that is shared among all

ESSID Wireless

Channel 6 Select the channel ID for wireless connection.

802.11 Mode 802.11g+802.11b

Channel Width Auto 20/40MHz Select of channel width of Auto 20/40 MHz or 20MHz

Transmit Power 10%

points in a wireless network. It is case sensitive and must not
exceed 32 characters.

Select the 802.11 mode of following:：

-802.11n+802.11g+802.11b

-802.11n+802.11g

-802.11g+802.11n

-802.11n only

-802.11g only

-802.11b only

To Adjust the output power of the system to get the
appropriate coverage of your wireless network. Select the
10% to 100% that you needed for your environment.

20

In Wall Access Point

3-2-2 Wireless Advanced Setting

Figure 11 Wireless Advanced Setting Screen

Item Default Description

Beacon Interval 200

RTS Threshold 2347

Fragmentation

2432

Threshold

Preamble Type Long Preamble

This value valid range is 1 to 1000 indicates the frequency
interval of the beacon.
This value valid range is 256-2342. This setting determines
the packet size at which the Wireless Subscriber Gateway
issues a request to send (RTS) before sending the packet. A
low RTS Threshold setting can be useful in areas where
many client devices are associating with the Wireless
Subscriber Gateway, or in areas where the clients are far
apart and can detect only the Wireless Subscriber Gateway
and not each other.
This setting determines the size at which packets are
fragmented. Enter a setting ranging from 256 to 2432 bytes.
Use a low setting in areas where communication is poor or
where there is a great deal of radio interference.
The preamble type is a section of data at the head of a
packet that contains information the Wireless Subscriber
Gateway and client devices need when sending and
receiving packets. The setting menu allows you to select a
long, short or dynamic preamble type.

In Wall Access Point

21

Click Apply button to save the new settings.

3-2-3 Wireless Security Setting

Figure 12 Wireless Security Setting Screen

Item Default Description

Select disable to allow wireless station to communicate with

Security Disable

WPA2 Encryption Wi-Fi Protected Access Encryption
Pre-shared Key Empty Enter a pre-shared key from 8 to 63 case sensitive ASCII

Group Key
Re-Keying
WPA Encryption Wi-Fi Protected Access Encryption

22

86400 Seconds Enter a number in the field to set the force re-keying interval.

the device without any data encryption. Select enable to
enable WPA or WEP data encryption.

characters.

In Wall Access Point

Pre-shared Key Empty Enter a pre-shared key from 8 to 63 case sensitive ASCII

characters.
Group Key
Re-Keying

86400 Seconds Enter a number in the field to set the force re-keying interval.

In Wall Access Point

23

Item Default Description

This selects which of the Keys the In Wall Box Access Pointuses
when it transmits. You can change the selected encryption key
every now and then to increase the security of your network.
Note: You have to configure all WEP keys (1~4), and select one

WEP Key 1

Click Apply button to save the new settings.

Click Apply button, the restart dialog box appears. Click on App ly to restart the system.

of the four WEP key.
Enter 5 characters (case sensitive) for ASCII 64-bit WEP Key.
Enter 10 characters (case sensitive) for Hex 64-bit WEP Key.
Enter 13 characters (case sensitive) for ASCII 128-bit WEP Key.
Enter 26 characters (case sensitive) for Hex 128-bit WEP Key.

Figure 13 Restart Dialog Box

24

In Wall Access Point

Advanced

3-3

3-3-1 Management

Define the In Wall Box Access PointManagement configuration

In Wall Access Point

Figure 14 Management Setting Screen

25

Item Default Description

Username The username can consist of up to 20 alphanumeric

Administrator Setting

Date/Time

Date (Year/Month/Day) System Date

Time (Hour:Minute:Second) System Time The system time of the In Wall Access Point.

Password The password can consist of up to 20 alphanumeric

characters and is sensitive.

characters and is sensitive.

The system date of the In Wall Access Point. The valid
setting of year is from 2002 to 2035.

NTP Setting Disable

Server IP/Domain Name Empty

Time Zone GMT-12:00 Select the appropriate time zone for your location.
Update Time 0 hours Enter the number of hours for update time.

Daylight Saving Time

LED Setting Disable Enable or Disable Device LED lighting.

Secure administrator IP
Addresses

Allow remote user to ping
the device

-

-

Disable Enables or disables Daylight Saving Time (DST).

Month/Day

Any

Enable

Click “Get from my Computer” button to correct the
system date and time.

Click “Get from NTP server” button to correct the
system date and time.

Enables or disables NTP (Network Time Protocol)
Time Server. Network Time Protocol can be utilized to
synchronize the time on devices across a network. A
NTP Time Server is utilized to obtain the correct time
from a time source and adjust the local time.
Enter the IP address/domain name of NTP server. The
maximum allowed characters length is 100.

Set the Daylight Saving Time (DST) on the In Wall
Access Point. Adjust the begin time and end time.

Options: Any and Specify. Administrator can specify 5
IP addresses or a range to allow remote control access
from network.
This function allows remote user to ping the In Wall
Box Access Pointthrough Internet. Ping is normally
used to test the physical connection between two

26

In Wall Access Point

devices, to ensure that everything is working correctly.

3-3-2 Firmware

The Firmware Upgrade menu loads updated firmware to be permanent in flash ROM. The download file
should be a binary file from factory; otherwise the agent will not accept it. After downloading the new
firmware, the agent will automatically restart it.

 Manual Firmware Upgrade

Figure 15 Manual Firmware Upgrade Setting Screen

Item Default Description

This allow administrator to upgrade the firmware via HTTP.

Local PC File Path Empty Enter the file name and location in the Local PC File Path

field.

This allows administrator use TFTP server to upgrade firmware.

Remote TFTP Server IP
Address
File Name Empty Enter the file name in the File Name field.

Empty Enter the IP address of TFTP Server.

Note:

1. Before downloading the new firmware, users must save the configuration file for restore

configuration parameters of the device.

2. Do not turn the power off during the upgrade process. This will damage the unit.

In Wall Access Point

27

 Scheduled Firmware Upgrade

Scheduled Firmware Upgrade is a program that enables an automatic upgrade to the latest firmware
version through the TFTP server.

Figure 16 Scheduled Firmware Upgrade Setting Screen

Item Default Description

Disable/Enable Disables or enables the scheduled firmware upgrade function.
TFTP Server IP Empty Enter the IP address of TFTP Server.
File Synchronization Empty Enter the file name and location in the File

Synchronization field.

Click the button to display synchronization file example.
Frequency Weekly Set the firmware upgrade time. The default value is

“Weekly”.

Figure 17 Synchronization File Sample Code

Note: Do not turn the power off during the upgrade process. This will damage the unit.

28

In Wall Access Point

3-3-3 Configuration

This feature can backup the system configuration from this device to your PC or restore your stored
system configuration to this device.

Figure 18 Configuration Setting Screen

Item Default Description

Backup Click it to save the system configuration to your computer. (export.cfg)
Remote TFTP Server IP

Address
File Name Empty Enter the file name in the File Name field.

Restore Click it to restore your system configuration.
Local PC File Path Empty Enter the file pathname of the system configuration file in the

Remote TFTP Server IP
Address

File Name Empty Enter the file name in the File Name field.
Reset the system back

to factory defaults
Keep subscriber profile Disable Click the keep subscriber profile to change all the parameters

In Wall Access Point

Empty Enter the IP address of TFTP Server.

Local PC File Path field.

Empty Enter the IP address of TFTP Server.

Erase all setting and back to factory setting.

29

into factory setting but still reserve the subscriber profiles.

30

In Wall Access Point

3-3-4 SNMP

The SNMP Agent Configuration screen enables you to access to your device via Simple Network
Management Protocol. If you are not familiar with SNMP, please consult your Network Administrator or
consult SNMP reference material. You must first enable SNMP on the SNMP Agent Configuration
screen.

Figure 19 SNMP Setting Screen

Item Default Description

SNMP Disable Disables or enables the SNMP management.
SNMP Port
Trap Port 162

Configuration
Community

Name

NMS
Address
Privileges Read/Write Choose “Read”, “Write”, “Trap Recipients” and “All” for different

Status Valid/Invalid Chosen “Valid” or “Invalid”. The default setting of entry 1, 2 are valid

In Wall Access Point

161

public/private

ANY

If the SNMP enables, also allowed to specific the SNMP port number
via NAT. The allowed SNMP port numbers are 161 (default),
16100-16199 and Trap port numbers are 162 (default), 16200-16299.
This Port setting is useful for remote control via NAT network.

Every unit with SNMP enable must be configured to recognize one or
more community names up to 20 characters. The default setting for
the community of entry 1 is “public” and for the entry 2 is “private” and
others are empty.
The address of the NMS. The default settings for the NMS Networking
are “ANY”.

privileges. The default setting of the entry 2 is “write” and others are
“read”.

31

and others are invalid.

3-3-5 System
3-3-6 Ping Command

The Ping function can check the Wireless Subscriber Gateway networking connective or not.

Figure 20 Ping Command Screen

Item Description

IP or URL Enter the IP address or the URL link.

Advanced

3-4

3-4-1 Restart

If your In Wall Box Access Pointis not operating correctly, you can choose this option to display the
restart Wireless Subscriber Gateway screen. Clicking the apply button restart the In Wall Access Point,
with all of your settings remaining intact.

Figure 21 Restart Screen

32

In Wall Access Point

In Wall Access Point

33

3-4-2 Logout

If you would like to leave the configuration page, please click apply to exit.

Figure 22 Restart Screen

Appendix A Signal Connection Arrangements

RJ-45 Ethernet Port

The In Wall Box Access PointRJ-45 Ethernet port can connect to any networking devices that use a
standard LAN interface, such as a Hub/Switch Hub or Router. Use unshielded twisted-pair (UTP) or
shield twisted-pair (STP) cable to connect the networking device to the RJ-45 Ethernet port.
Depending on the type of connection, 10Mbps or 100Mbps, use the following Ethernet cable, as
prescribed.

10Mbps: Use EIA/TIA-568-100-Category 3, 4 or 5 cable.
100Mbps: Use EIA/TIA-568-100-Category 5 cable.

Figure 23 RJ-45 Connector and Cable Pins

Note: To prevent loss of signal, make sure that the length of any twisted-pair connection does not

exceed 100 meters.

34

In Wall Access Point

Appendix B Regulations/EMI Compliance

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.

NCC警語:

(1)「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功
率或變更原設計之特性及功能」警語以及(2)「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；
經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定
作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」
警語。

In Wall Access Point

35

LIMITED WARRANTY

In Wall Access Point

What the warranty covers:

We warrant its products to be free from defects in material and workmanship during the warranty period.
If a product proves to be defective in material or workmanship during the warranty period, we will at its
sole option repair or replace the product with a like product with a like product. Replacement product or
parts may include remanufactured or refurbished parts or components.

How long the warranty is effective:

The Easy Hotspot Kit is warranted for one year for all parts and one year for all labor from the date of
the first consumer purchase.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser.

What the warranty does not cover:

1. Any product, on which the serial number has been defaced, modified or removed.

2. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product

modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by us.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meeting our specifications.
g. Normal wears and tear.
h. Any other cause that does not relate to a product defect.

3. Removal, installation, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact our Customer Support.

2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address (d) a description of the problem and (e) the serial number of the product.

3. Take or ship the product prepaid in the original container to your dealer, and our service center.

4. For additional information, contact your dealer or our Customer Service Center.

Limitation of implied warranties:

THERE ARE NOWARRANTIED, EXPRESSED OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Exclusion of damages:

Our LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. We
SHALL NOT BE LIABLE FOR:

1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES
BASED UPON INCONVENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF
PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH
BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THE
POSSIBLITY OF SUCH DAMAGES.

2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

36

In Wall Access Point

3. ANY CLAIM AGAINST THE CUSOMER BY ANY OTHER PARTY.

In Wall Access Point

37