HDANYWHERE HDA 250850 User guide

MHUB U (4x1+1) 40

CODE: MHUBU41140

Product Guide (English UK)

Revision 1: 11/12/19

Box. Features. Specs.

2

1.

Glossary of termsContents

Glossary of terms, In the box 4-5

Features, Specications 6-7

Panel description & MHUB U (4x1+1) 40 panel diagram 10-11

MHUB U (4x1+1) 40 Display Receiver 12

MHUB U (4x1+1) 40 HDMI IR Dongle 13

IR (Infrared) control 14

Using the Master Remote Control, Testing that IR works 15

Cabling 16

Hiring a HDA Pro 17

MHUB control methods 18

Control drivers & API 19

Example wiring diagram & explanation 22-24

Power up 25

Setup on uControl (WiFi + Ethernet) 28-29

Accessing MHUB-OS & settings 32-33

uControl interface 36-37

Legals: Compliance, conformity, Product Guarantee 40-41

Audio Return Channel

Consumer Electronics
Control (CEC)

Control System

HDBaseT

IR RX & IR TX

MHUB

MHUB-OS

Tipping Point
Compression (TPC)

uControl

ARC enables audio from a display to be extracted
and returned to MHUB.

An optional feature-set within the HDMI

specication allowing a single remote control to

control multiple devices connected via HDMI.
A 3rd party method of control for MHUB systems.

For example, Crestron, Control4, RTI, Savant, Fibaro
etc.

Technology used to convert HDMI in to a format

which can be carried over network cable.

Infrared (IR) Receiver (RX) and Transmitter (TX). The

RX ‘receives’ a signal from another remote control

and the TX ‘transmits’ it.

Video or Audio distribution systems manufactured
by HDANYWHERE.

MHUB’s on-board operating system from which most
settings can be congured.

Video content such as Ultra HD 4K 60 4:4:4 uses
up to 18Gbps of data at any one time which is not

possible over current HDBaseT technology. HDA

makes transmission of 18Gbps content possible

using TPC. Visually lossless, TPC only becomes

active if HDBaseT’s threshold is breached, hence the

term tipping point.

A remote control app made by HDANYWHERE and
available from iOS & Android app stores.

Help is only an email away: [e-mail]. 4

In the box

Name: MHUB U (4x1+1) 40

Product code: MHUBU41140

x1 MHUB U (4x1+1) 40 Chassis/Hub

x1 Display receiver

x1 HDMI IR Dongle

x1 Detachable WiFi aerial

x7 Infrared Transmitter cable (1.5m) (IR TX)

x3 Infrared (20-60Khz) Receiver cable (1.5m) (IR RX)

x1 Three Pin Phoenix Connector

x1 Display receiver mounting bracket

x1 Master remote control

x1 RS232 serial cable (1.5m)

x1 24V 1A Power Supply with IEC lead & adapters (UK,EU,US,AU)

x1 User Guide

5

FeaturesIMPORTANT:

For optimum performance and safety, please read these instructions carefully

before connecting, operating or conguring this product. Please keep this manual

for future reference.

Surge protection is recommended

This MHUB system contains sensitive electrical components that may be damaged
by electrical spikes, surges, electric shock, lightening strikes, etc. The usage of
surge protection systems is recommended in order to protect and extend the life

of your system.

Supports video picture formats up to 4K@60Hz (4:4:4)

Multi-channel digital audio support up to and including Dolby/Atmos and DTS:X

Simultaneous multi-channel and stereo audio (no downmix)

Down-scaling on all outputs

ARC enabled (HDMI only)

Bi-directional IR (Display Receiver)

CEC & EDID management

uControl & Amazon Alexa compatible

Remotely monitorable

Includes HDA API 2.1

Two additional IR control ports

Network connectivity over WiFi and Ethernet

Power over HDBaseT (PoH)

Help is only an email away: [e-mail]. 6

Specication

HDMI version HDMI 2.0b

HDCP compliance HDCP 2.2 & HDCP 1.4

Video bandwidth 18Gbps

Video resolution Up to 4K@60Hz (4:4:4) with HDR

Colour space RGB, YCbCr 4:4:4, YUV 4:4:4, YCbCr 4:2:2/4:2:0

Colour depth

HDR formats HDR10, HDR10+, Dolby Vision, HLG

Video & audio IO

Transmission distance

HDMI audio formats

Coax audio formats PCM 2.0, Dolby Digital, DTS

Stereo audio formats PCM 2.0

Infrared 20Khz - 60Khz

Aerial connector SMA

Aerial frequency

ESD protection

8-bit, 10-bit, 12-bit (1080p@60Hz)
8-bit (4K@60Hz)
12-bit (4K@30Hz) HDMI only

Inputs: x4 HDMI
Outputs: x1 HDBaseT, x1 HDMI (Mirror), x1 HDMI,

x2 3.5mm Stereo Jack, x2 SPDIF

1080p 70m
4K 40m

PCM 2.0 / 5.1 / 7.1, Dolby Atmos / Digital / Plus /
EX, Dolby True HD, DTS, DTS-EX, DTS-96 / 24, DTS
High Res, DTS-HD Master Audio, DSD, DTS:X

2400 - 2500Mhz
5150 - 5850Mhz

±8kV (Air-gap discharge)
±4kV (Contact discharge)

Power consumption 15W (Maximum)

Chassis:

Power supply

Operating temperature 0°C - 40°C / 32°F - 104°F

Storage temperature -20°C - 60°C / -4°F - 140°F

Relative humidity 20 - 90% (Non-condensing)

Housing

Colour Grey (Carbonite)

Dimensions (W/D/H) mm

Weight

24V 1A

Display Receiver:

24V PoH (Power over HDBaseT)

Chassis: Steel
Display Receiver: Aluminium

Chassis: 200 x 200 x 36
Display Receiver: 120 x 65 x 18

Chassis: 1250g
Display Receiver: 125g

7

IO. Control. IR. Cabling.

8

2.

MHUB U (4x1+1) 40 panel description

1. Source (IN): HDMI video input ports indicated by numbers.

2. Video (OUT): HDBaseT (RJ45) & HDMI video output ports. The HDMI output
(B) mirrors HDBaseT output port (B) and is not switchable independently.

18Gbps video will pass through both HDMI (uncompressed) ports whilst the
HDBaseT port will use TPC (compression) simultaneously. The HDBaseT port
has two indicator lights. Left light: solid means connection between MHUB and
display receiver is good. Flashing means that the connection is poor. Off means
that there is no connection detected. Right light: solid means HDCP is detected.
Flashing means there is no HDCP. Off means no HDMI signal is detected.

3. Source IR (OUT): Connect an IR TX to control corresponding HDMI inputs.

4. Display IR (IN): Connect an IR RX to send a remote (IR) control command

through MHUB to the corresponding display “IR” output. (Page 12-13).

5. Global (OUT): Connect an IR TX to enable remote (IR) control of an AVRs,
soundbars etc.

6. HUB IR (IN): Connect an IR RX to enable remote (IR) control of MHUB.

7. WiFi: Connect the detachable WiFi aerial to connect to LAN over WiFi.

8. IP: Enables TCP/IP control of MHUB over Ethernet.

9. RS232: Enables a PC or control system to control MHUB over serial.

10. Audio (OUT): Optical & 3.5mm Stereo Jack audio output mirrored ports.

Coax outputs multi-channel audio and the 3.5mm Stereo Jack outputs 2ch PCM

with no downmix.

A. Power: LED indicator light. If this light is on and solid then MHUB has power

and is on. If this light is flashing, then MHUB is in Discovery Mode (see below) or

there is an error.

B. Source Selector: Selects a HDMI video input for output (A).

C. Source Selector: Selects a HDMI video input for output (B).

D. HDA Logo: IR window for Infra-red (IR) remote control commands.

Discovery Mode:

Press and hold Source Selector buttons marked “A” & “B” for 5 seconds
to put MHUB into Discovery Mode for WiFi setup. This will restore MHUB
back to default network conguration. You can not undo this action. During
Discovery Mode, MHUB’s Power LED indicator light will start to flash. If you
do not complete setup in 10 minutes then MHUB will exit Discovery Mode.

11. Power: Connect the power supply to MHUB.

Help is only an email away: [e-mail]. 10

Source / IR

1 2 3 4

A BB A

B

Global IR (OUT)

WiFi

5 6

Hub IR (IN)

IP

RS232

Digital/Stereo (OUT)

DC24V

Video (18G) / IR

PC: MHUBU41140

SKU: 1.05.904.023.1

MHUB U (4x3+1) 40: front & rear panel

A B CD

1
2

U

MHUB

3 4 5

7 6 11

WiFi

Source / IR

1 2 3 4

A

3
4

Video (18G) / IR

A BB A

1 2 10

Global IR (OUT)

1
2
3
4

5 6

IP

8 9

B

Hub IR (IN)

RS232

SKU: 1.05.904.023.1

PC: MHUBU41140

Digital/Stereo (OUT)

DC24V

B

11

IR

OUTIN

VIDEO

HDMI (OUT)RS232 (OUT)

DC24V

MHUB U (4x1+1) 40 Display Receiver: front & rear panel

1. Power LED: Indicator light. If this light is on and solid then the display receiver has power.

2. Power: DC24V / 1A. Unsupported port from other MHUB U systems.

3. Video: HDBaseT link between MHUB and display receiver. This port has two indicator lights. Left light: solid means connection between MHUB and display receiver is

good. Flashing means that the connection is poor. Off means that there is no connection detected. Right light: solid means HDCP is detected. Flashing means there is no
HDCP. Off means there is no HDMI signal at all.

4. HDMI (OUT): Connect a HDMI cable from the display receiver to your display to provide a picture.

5. IR IN: Connect an IR RX to send a remote (IR) control command from the display receiver to MHUB’s active “Source / IR” port.

6. IR OUT: Connect an IR TX to this port to control displays using remote (IR) control commands.

7. RS232 (OUT): Unsupported port from other MHUB U systems.

1

76542 3

Help is only an email away: [e-mail]. 12

OUT

IN

IR RX

CEC IR

MHUB U (4x1+1) 40 HDMI IR Dongle

MHUB can support the passing of IR or CEC commands over its HDMI output using the HDMI IR Dongle. If the Widget is in “IR” mode then IR commands can pass in either

one of two directions; from MHUB to the display, or from the display back to MHUB. Only one direction of travel is supported at any time. This mode is set inside MHUB-OS.

If the Widget is in “CEC” mode then supported commands travel from MHUB to the display only.

1. CEC/IR : HDMI IR Dongle operating mode. Ensure that this switch matches the type of control method you wish to use.

2. IR RX: Connect an IR RX or TX (you can set mode in MHUB-OS) to this port to control displays or pass remote (IR) control commands back to your source devices.

3. IN: Connect a HDMI cable from MHUB.

4. OUT: Connect directly in to your display to provide a picture.

1

3 4

2

13

IR (Infrared) control

MHUB can manage IR signals and route them to sources, AVRs or displays. Using

this feature will allow you to use a remote control and pass that IR command from
your display location to MHUB or vice-versa.

Sending IR commands from a display ‘back’ to MHUB

This will enable backwards IR control (the most common form of IR control) where

IR signals from a remote in any one of your zones is sent back to MHUB and your

source device.

1. Connect an IR TX to port labelled “Source IR (OUT)” on MHUB. Ensure that
the port number matches the port number of the corresponding video source
input, labelled “Source (IN)”. For example, if you have AppleTV plugged in to port

3, then the IR TX cable should also be connected to Source IR (OUT) port 3.

2. Place the IR TX bud (small tear drop part) in front of the IR window of the

source. Repeat for each source device you wish to control.

3. Connect an IR RX to port labelled “IR IN” on the display receiver.

4. Place IR RX head in line-of-sight of the remote control.

IR Receiver (IR RX)

IR Transmitter (IR TX)

Sending IR commands to a display

1. Connect an IR TX to port labelled “IR OUT” on the display receiver.

2. Place the IR TX bud (small tear drop part) in front of the IR window of the

display. Repeat for each display you wish to control.

3. Connect an IR RX to port labelled “Display IR (IN)” on MHUB. Ensure that the

port letter matches the port letter routed to the display receiver.

4. Place IR RX head in line-of-sight of the remote control.

Help is only an email away: [e-mail]. 14

1.5m

Output A

1 2 3 4

Output B

1 2 3 4

MHUB U (4x1+1) 40 Master remote control

MHUB comes with a master remote control.

The remote control is limited to video switching operations only (see section:
“MHUB control methods”).

The Master Remote control provides video switching control regardless of the

room or zone that the command comes from.This is useful if MHUB is installed

in an environment like a bar where you might want to switch all displays from one

source to another.

Testing that IR control works Using the Master remote

This section aims to verify that your MHUB’s IR control system is setup correctly
and assumes that your MHUB has been wired as per the instructions laid out in this

manual. Please refer to the MHUB wiring diagrams in this document to ensure that
your setup matches that before proceeding with the verication below.

Testing basic operation from a display ‘back’ to MHUB

To verify that IR control is working correctly proceed to any display receiver location

with an IR RX connected to it. Use the MHUB Room Remote to select a source
with an IR TX connected to it at the MHUB end. You should notice that the MHUB
switches to that source on your display. Now pick up your source remote control for

the source you just switched to and attempt to control the source using the native

remote control. If both work then you have setup IR control correctly. Repeat this
step for all display receiver locations.

Testing commands from MHUB to a display

To verify that control commands from MHUB to your display are working you will
need to use uControl, or test using the following method. 1) select a display that
you wish to test 2) connect an IR RX to the corresponding Display IR (IN) input 3)

ensure that the display receiver has an IR TX connected and that it is pointed to

the display IR receiving window 4) take the display remote control to the MHUB
location and point the remote at the IR RX, test the on/off command. The display
should turn on or off. This will conrm that IR can pass from MHUB to your display

successfully.

Working with identical source devices (discrete IR)

MHUB can work with multiple source devices that are identical due to its discrete
IR function. Discrete IR avoids IR clashes that result in unwanted operation of all

identical devices. MHUB manages this by targeting IR commands specically to
the source device being watched on the display. When using two or more identical

source devices, take measures to avoid IR transmission leaks that could cause the
identical source devices to respond in error. This includes simple measures like

placing identical sources on different shelves or attempting to ‘hood’ the IR TX so
that IR signals can not leak.

15

Cabling

Currently you can use Cat6, Cat6e, Cat6a, Cat7 or Cat7a with MHUB. Cat5e may
work, but is not recommended, due to bandwidth requirements required by the
system.

Note:

DO NOT USE ANY COPPER CLAD ALUMINIUM (CCA) Cat 6/7 CABLE.

Optimum performance

Whichever network cable type you choose, ensure that the main wiring architecture
is ‘solid core’ and not stranded ‘patch’ cabling. Patch cabling can be used for the
last few metres of a run (e.g wallplate) but should be avoided over longer runs as
signal transfer over stranded cores is signicantly impacted. The use of pre-made

leads is not recommended unless you can be absolutely sure of their construction

credentials (i.e. solid core 568B). For optimum performance, use a single piece of

Cat cable terminated directly at the transmitter and the receiver ends. Make sure to
use the correct connector types (i.e. RJ45 solid core) crimp connectors.

Shielded cables

Shielded FTP cable is not a stipulation. However, if you are using this type of

cable ensure compatible shielded accessories are used. Failure to terminate cable
screen at all points can induce interference rather than eliminate it.

Patch panels and wall plates

If patch panels are terminated correctly then there is a minimal loss of distance.
The use of wallplates and patch panels has the potential to cause increased

resistance on the cable introducing pinch points for signal transmission and could
reduce transmission lengths. TIP: Instead of using RJ45 wallplates search for
“brush plates” this will yield many results.

HDMI cabling

HDANYWHERE recommends using suitably robust and good quality HDMI cables.
It is not advised to use passive HDMI cables over 5 metres in length either on

the inputs or the outputs of MHUB or its display receivers. Where HDMI cables

longer than 5 metres are required, HDA recommends utilising it own brand of long

distance HDMI cables or a suitable alternative.

W

a

?

t

e

c

h

m

i

o

t

e

v

a

h

t

n

o

D

n

l

i

n

e

!

1 2 3 4 5 6 7 8

https://youtu.be/EbWAEndiCuU

1

2

3

4

5

6

7

8

Terminate using RJ45 connectors to 568B wiring standard.

Help is only an email away: [e-mail]. 16

Hire a HDA Pro

If cabling infrastructure, installation and control seem like too much to absorb and learn then why not hire a HDA Pro to do the work instead for you?

Having your MHUB system professionally installed should help to guarantee the system’s long-term performance and ensure that it blends neatly with your decor.

All HDA Pros have the added ability to manage your system remotely for you - meaning that routine maintenance and even advanced troubleshooting can be done
without the need to visit your home. Ask our HDA Pros for home control, cinema, heating/AC, lighting and security services. Download a guide to picking a HDA Pro
here: https://content2.hdanywhere.com/en/downloads/documents/hdanywhere_doc-picking-an-installer.pdf

Find a HDA Pro anywhere in the world today

Visit: https://hdanywhere.com/dealers-and-installers/

17

MHUB control methods

MHUB has been designed to be operated and controlled in numerous ways depending on your requirements. There are limited control options from the front panel and from

the Master remote, so attention needs to be paid to the method by which MHUB will be controlled. The methods to control and considerations for each are listed below.

Remote Controls (IR)

MHUB supports the passing of IR commands from any display location back to MHUB and vice versa, this is described on pages 14-15. This is the recommended method
to gain instant control of all source devices located near MHUB. Note: switching to audio sources such as ARC is not supported. In scenarios such as this, HDANYWHERE
recommends using MHUB-OS’ dashboard or uControl.

uControl

Available for free on iOS and Android, uControl is MHUB’s native method of control. All of MHUB’s built-in features are available; offering comprehensive control over
switching, source/display control, ARC access and executing Sequences in all zones. uControl communicates over the same Local Area Network (LAN) as your MHUB which
allows for global control over the entire system regardless of what zone you are in. In the absence of a third-party control system, HDANYWHERE recommends uControl as

the method to control your MHUB on a daily basis.

Voice

All MHUB systems support voice control as standard via an Amazon Echo (Alexa) device. Voice control is not designed to act as a primary control method but to assist the
other methods listed on this page. Using voice it is possible to change channels, execute sequences, turn MHUB on/off and basic transport commands such as play/pause/
forwards/backwards from any zone. Please note that Amazon Alexa is not available in all countries.

Third-party control system

Control via a third-party control system is supported using our latest and most advanced API to date. For an up-to-date list of systems that MHUB supports please visit
the “Control Drivers” section of our support site: http://support.hdanywhere.com. Control varies depending on the control system being used but typically, switching is
supported with other drivers able to offer more. Please consult a HDA Pro (page 17) to nd out more.

MHUB-OS

Any device with a web browser can control MHUB directly from MHUB-OS’ dashboard. From here it is possible to control switching and ARC. MHUB-OS is also where all
conguration for MHUB is done.

Help is only an email away: [e-mail]. 18

Control system drivers & HDA API

MHUB works with many control system providers. Find the latest drivers to download from http://support.hdanywhere.com.

Building your own control solution

Use MHUB’s open API to create a customisable control solution. Replicate almost any function within MHUB in to your own control application.
Download the API here: https://cloud.hdanywhere.com/docs/api/hda_api.pdf

19

20

Wiring. Power Up. First Boot.

3.

Example wiring diagram

Living Room

ROUTER

TV APP

OUT

CEC IR

IR RX

IN

ARC

AVR

Bedroom

4K or 1080p

Display

Receiver

uControl

VOICE
CONTROL

HDMI Cable
Ethernet Cable

3.5mm Stereo
CableHDBaseT
IR RX/TX Cable
Speaker Cable

Help is only an email away: [e-mail]. 22

Diagram explanation

In the diagram (“Example wiring diagram”) we have detailed a setup to show how
the majority of MHUB’s feature-set could be connected and demonstrated together.

MHUB, sources, displays and the AVR are controlled by uControl and Amazon Alexa.

Decentralised or centralised installation

This MHUB is working decentralised: meaning that it is not installed in a central
location from which everything is connected. In this example, MHUB is situated
in the same zone as one of its outputs (Living Room) using a standard HDMI

cable. Connected to the MHUB are three video sources and an AVR. The AVR is

providing amplication for the multi-channel speaker setup in the Living Room and

is controlled by IR via one of MHUB’s Global IR (OUT) ports.

Video outputs A & B terminate in zones; Living Room and Bedroom respectively.
The Living room is fed from a standard HDMI cable and the Bedroom is connected

via Cat 6 cable to a display receiver.

Network connectivity is fed to MHUB via WiFi provided by a router. Connecting
MHUB to LAN will ensure that uControl can congure MHUB and control the entire

system.

Living Room

The Living Room has an IR RX (see page 14) connected to its HDMI IR Dongle (see
page 13). IR signals can be passed back to the source devices located next to the
MHUB meaning that those source devices can be hidden away in a cupboard or
out-of-sight for a neat and tidy nish. Control over the TV and the sources is done
using each devices native remote control which are kept in the Living Room. The
display in the Living Room is 4K and MHUB will send uncompressed 4K content

directly to it. Audio is provided directly from the video sources or can be extracted
from the display via ARC and routed to the AVR for multi-channel audio output on
demand.

Bedroom

MHUB can downscale 4K to 1080p so the option for mixed resolution displays are

possible. The Bedroom is connected by HDBaseT using Tipping Point Compression
(TPC) to display a theoretical maximum 18Gbps bandwidth picture. This room has
no remote controls. Control of the TV and source devices are done using voice

commands or uControl.

Note:

MHUB has been designed so that it can be installed in several different
ways. The purpose of the diagram is to illustrate a typical/example setup
and assumes that you are already familiar with the basics of wiring and
infrastructure. If you are unsure how you might install MHUB in to your
property then contact [e-mail] for further assistance.

23

Using XTND HDMI Extenders on the HDMI output

It is possible to extend the range and function of the HDMI output on MHUB by using a XTND HDMI Extender and a MHUB + XTND IR Integration Kit (“1” in diagram below).
XTND and the Integration Kit are sold separately as an optional extra. For more information, please visit HDANYWHERE.com

HDMI Cable
Ethernet Cable

3.5mm Stereo
CableHDBaseT
IR RX/TX Cable
Speaker Cable

IN

IR RX

Ensure mode: “IR”

CEC IR

OUT

Kitchen

4K or 1080p

1

HDMI Male to Female Adapter

XTND (TX) XTND (RX)

Help is only an email away: [e-mail]. 24

Power up

This section describes the power up process for MHUB U (4x1+1) 40, operating in standalone mode (by itself). If you are creating a V&A/stack system then please consult

the MHUB AUDIO manual for detailed instructions.

Power up sequence for MHUB U (4x1+1) 40

1 Ensure that all devices are turned off.

2 Connect HDMI sources to the input ports on MHUB. If any sources require IR control, ensure that IR is connected at this stage as well.

3 Connect the display receiver to MHUB using Cat 6/7 cable in to MHUB’s video output port.

4 Connect any HDMI video outputs such as displays, AVRs or mirrored displays using HDMI cables from MHUB’s video output ports.

5 Connect MHUB’s audio output ports to speakers, AMP/AVRs or distribution hardware such as MHUB AUDIO.

6 Ensure that HDMI cables are fed from display receivers or HDMI IR Dongles in to their respective displays and that any IR hardware is connected as well.

If you are connecting to LAN via Ethernet then connect a cable between your router and the IP control port on your MHUB.

7

If you are using WiFi then you must activate Discovery Mode after step #11. (See pages 10 & 28).
Important: If you are connecting over WiFi then do not connect an Ethernet cable to MHUB.

Plug in the supplied power lead, MHUB will automatically power on and power will be fed to all display receivers. MHUB and any connected display receivers LED

8

indicators should be lit and solid.

9 Turn on each source device one after another followed by each display.

10 Ensure that displays are set to the correct HDMI input. Picture and sound from source devices will now be displayed on screen.

11 MHUB will start its power up sequence (this can take up to 120 seconds after step #8). Ensure this period has passed before proceeding to the next step.

12 Install uControl on your iOS or Android device and run the application.

13 Complete setup on uControl (see “Setup on uControl”).

25

26

Setup with uControl.

4.

Setup on uControl

Before starting setup on uControl, ensure that your MHUB is wired correctly and has been on for over 120 seconds to ensure that it is fully initialised. If you are connecting

to MHUB via Ethernet cable then make sure your phone or tablet is also connected to the same network and proceed with setup detailed below.

Setting up for WiFi and putting MHUB in to Discovery Mode

To congure MHUB’s WiFi you will need to put it into Discovery Mode rst (see page 10). Ensure that MHUB is in this mode prior to completing the uControl setup process.

uControl is required for setup but optional to use

uControl is available on iOS and Android Play stores and can be found by searching “uControl” - look for a black icon with “HDA” written inside it. You do not need to use

uControl with your MHUB but it is required to setup your MHUB system.

Start setup with uControl (Part 1)

1 . Load uControl. You will be presented with an intro screen which will automatically disappear or can be swiped away.

2. You will be at the home screen. This screen is only visible when no MHUB system is paired with uControl. Your following choice is dependent on the way you wish to

connect it to your network.

A. If your MHUB is connected to your network via Ethernet cable then select “Connect to MHUB System”.
B. If your MHUB is being setup to operate on WiFi then select “Connect Manually” then “Congure WiFi Device” .

3. If you selected option #2A then MHUB will scan your network and connect to your system for further conguration or normal use. If you selected option #2B then
uControl will walk you through steps to join MHUB to your WiFi network rst. You will need your router SSID and Password to complete this.

Both options will proceed to step #4.

4. uControl will scan for devices in your network over Ethernet or Wi.

5. If there are no errors in the scan then uControl will present you with the following options:

A. If a standalone MHUB is found then uControl will proceed to congure that system directly. Jump to step #7.

B. If multiple MHUB’s are found then uControl will ask if you want to stack those systems (if supported) or connect to one of them individually.

6. If MHUB is being setup in Stack mode then you will be asked to nominate a Master and Slave device(s).

7. uControl will then connect to your system to start the conguration process.

8. You will now be redirected to MHUB-OS, the operating system on board MHUB, to complete the rst boot process (see next page).

Help is only an email away: [e-mail]. 28

... From uControl, proceed to congure MHUB-OS’ rst boot process (Part 2)

1 . EULA & Privacy Policy

2 . Name your MHUB

3A. Dene connections (Stack only)

3B. Split inputs (Stack only)

4. Name your source devices

5 . Create zones

6 . Assign outputs to zones

7 . Conrm zones An opportunity to review your changes.

8 . Connect MHUB to HDA Cloud

9. Complete setup A nal step before returning back to the main uControl interface.

End User License Agreements and Privacy Policy statements. You can not proceed with setup if these are not agreed
to rst.

Provide a unique name for your MHUB so that you can identify it easily. In stack mode all detected MHUB devices will

appear here.

If your MHUB(s) are being setup in stacked mode then this is where you will dene what outputs from your Master
MHUB system are being routed to inputs on your Slave MHUB system(s).

If you are using an audio splitter to split one or more audio sources to multiple MHUB systems then this is where this
relationship is dened.

Give each one of your source devices a unique name (eg “Sonos”, “CD Player”) so that you can identify and switch to
easily. If you are setting your MHUB up in stack mode then any inputs assigned in steps 3a & 3b will become locked
and unavailable to edit as their input is dynamic depending on the output of the master device.

A zone is a room or location in your property where outputs from MHUB terminate in (eg “Kitchen”, “Living Room”,
“Bar”).

A zone can contain up to 1 output in total. However, zones are limited to supporting only one video enabled MHUB

output.

Register MHUB on HDA Cloud to access online services, to extend your warranty and to grant permission for remote
monitoring and management to take place if your MHUB has been installed by a HDA Pro. The email address must
belong to the owner of the MHUB device.

29

30

6.

MHUB-OS.

Accessing MHUB-OS

MHUB-OS is the operating system on board all MHUB systems and must be congured rst before you can use it (see page 28-29). MHUB-OS manages the operation of
your MHUB, the connection between MHUB and your control method (see page 18) and the connection to online services like HDA Cloud and Amazon Alexa. MHUB-OS is
not typically a feature that you would access daily but something where conguration and user settings are applied so that MHUB operates in the manner you like.

Accessing MHUB-OS

1. Ensure that you have completed the rst boot process and that MHUB is on and connected to your network.

2. Load uControl: it will connect with MHUB and you will be taken to the main control interface.

3. Tap on the Menu icon represented by three horizontal lines. A menu will appear from the left side of your screen.

4. Tap on the Cog icon in the bottom left corner to be navigated to the main Settings menu.

5. Select option: “Access MHUB”.

3

5

4

Help is only an email away: [e-mail]. 32

MHUB-OS pages described

Conguration options for MHUB within MHUB-OS are detailed below.

Homepage / Dashboard The homepage for MHUB-OS. Control input switching, power and toggling ARC mode from this page.

Create a HDA Cloud account and register MHUB to extend warranty by 1 year. Registering MHUB on HDA Cloud
will allow MHUB to connect to other online services such as Amazon Alexa and will grant permissions to have
MHUB remotely managed by your installer (HDA Pro) if you have one. Having this account in place will also allow

HDANYWHERE to access technical data from your system to provide better support should you experience any

Account Management

MHUB Setup

Network Settings Manage the network settings for MHUB such as DHCP and WiFi settings.

uControl

Sequences & Scheduling

Voice Control Options to congure voice control for supported devices can be found here.

difculties.

HDA Pro pairing:
If you are a professional installer and have an approved HDA Pro account then add your details to the HDA Pro
area in addition to the HDA Cloud account details to setup MHUB for remote management. Ensure that you
have permission from the MHUB owner and that their HDA Cloud account is in place otherwise pairing/remote
monitoring will not be possible.

This page describes basic conguration settings needed to operate MHUB on a daily basis. It contains a list
of MHUB-OS software, rmware and identifying information. From here it is possible to name source devices,
create and manage zones, manage output assignment, set time zone, set security PIN and apply a custom LCD
message (if applicable).

Download or delete uControl Packs from HDA Cloud and assign them to input or display receiver IR ports to
enable remote control of sources, displays and AVRs. Set the operating mode for the HDMI IR Dongle and test

CEC commands to see if your display is supported.

A Sequence is a string of individual commands such as (switch to input 1, change channel to 101, mute output
A & D) which can be triggered by a single button press or Alexa voice command. Create and test Sequences
from this page. Additionally, it is possible to schedule a Sequence so that it executes automatically at a set time

or date.

AV Settings Manage EDID and video scaling from this page.

Control Drivers Links to HDANYWHERE Support (http://support.hdanywhere.com).

33

34

7.

uControl it.

uControl interface

uControl is MHUB’s native method of control which can be used to control all
sources, AVRs, displays and other MHUB devices from anywhere in your property.

The following pages describe the main interface areas, their function and how to

use them.

3

1 2

Tapping this button reveals the zone selector and allows access to the

1

settings menu (see #10-12).

This label indicates the zone that you are controlling. All control commands

2

are targeted in this area.

Zone power control: this button reveals a sub menu containing all devices
available which can be turned on or off. Power buttons can be displayed in
two colours describing how you interact with the button: Red) indicating the

3

device power control can be toggled, a tap to turn on and a tap to turn off.
Blue) meaning that the power control requires an explicit interaction to turn

on or off. Tap to turn off and press and hold for 2 seconds to turn on.
Control selector bar. This bar includes all sources that can be controlled

in your system. All devices are listed in this bar and navigating between

4

devices can be done by swiping left or right horizontally. Devices can be
removed or added back by accessing uControl settings.

Control group icon: on smaller devices controls are grouped together for
quicker access. If your device has its controls grouped then the icons will

5

appear here, examples are numeric keypads, or playhead controls which are

typically grouped together.

Control interface. This area is where your control interface is displayed. The

6

control interface will change dynamically depending on the device that you

have selected from the control selector bar.

Gesture control area will appear in the control interface as a large square or
rectangle. This area supports nine control types familiar to all mobile device
users. Swipe up, down, left or right to replicate the same command on your

7

device. Tapping acts as an Enter command. Additionally, if supported, then
two ngers down will pause and two ngers up will resume. Drawing a
chevron to the right will skip forward and a chevron to the left will take you

back.

Help is only an email away: [e-mail]. 36

4

5

6

7

8

9

Audio selector icon. Tapping this icon will cycle through the different audio

devices that are available in that zone.

1. Display audio (TV & speaker icon):

Provides volume/mute control for the display. Pressing and holding the TV

icon will reveal ARC options if supported and any audio inputs connected
to the MHUB.

2. AVR audio (AVR icon):

If the zone contains an AVR then volume/mute controls will be presented.

8

When selected, all volume commands will be directed to the AVR instead
of the display.

3. MHUB AUDIO (MHUB AUDIO icon):
A third tap will enable MHUB AUDIO volume control of speakers in that

zone if MHUB PRO 2.0 has been congured as a V&A/stack. In this mode,

volume buttons are replaced with an audio slider and an additional label is

displayed to inform the user what audio is being routed to the speakers.
Pressing and holding this icon will reveal a source selector menu allowing

you to switch to audio inputs directly connected to MHUB AUDIO.

Volume control: increase or decrease volume by using a slider (MHUB
AUDIO only) or tapping the “+” or “-” buttons. Tapping the mute icon will

9

reduce the volume to 0 or put the device in a mute state. Volume commands

are targeted depending on what audio device is active as per point #8.

Tap to access uControl and MHUB-OS settings for app and MHUB

10

conguration options.

Change zones by selecting the zone you wish to control here. If a blue

display icon appears then this means that there is display control in that

11

zone. Zones can be reordered or removed by pressing and holding on the
zone label and then clicking “Done” which appears near location #10.

Execute Sequence. If you have created a Sequence in MHUB-OS then you

12

can make it visible from uControl’s setting page. Tapping the Sequence

button will execute that Sequence anywhere in the property.

10

11

12

e

m

i

?

t

W

e

v

a

h

t

’

n

o

D

https://youtu.be/4qGYH4q0XEM

a

t

c

h

o

n

l

i

n

e

!

37

38

The Legal Bit.

8.

Important information

Terms & Policies, including General Data Protection Regulation (GDPR) and other Data Protection Laws.

During the setup of MHUB, the HDA Pro (Installer) and End-User are required to agree to a set of terms, conditions, rules, policies and license agreements, including the
HDANYWHERE Privacy Policy. These terms, notices and policies are, collectively, the “Agreements”. By installing or using MHUB, you agree to be bound by the Agreements.

EU Conformity

Hereby, HDANYWHERE declares that this HDMI connectivity device is in compliance with the essential requirements and other relevant provisions of the following Directives:
2006/95/EC (LVD Directive); 2004/108/EC (EMC Directive); 1999/5/EC (R&TTE Directive). The full text of the EU declaration of conformity is available in the compliance
section at HDANYWHERE.com/legals

Recycling your device properly

In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of or recycle your device in accordance with your local laws and regulations.

Help is only an email away: [e-mail]. 40

HDANYWHERE Limited Product (2 or 3 Year) Guarantee

WHO WE ARE

1. We are HD CONNECTIVITY LTD trading as HDANYWHERE (“HDA”), a limited company registered under number
06046737 in England and Wales with its registered ofces at The Hayseld, Malvern, WR14 1GF, United Kingdom.

OUR GUARANTEE TO YOU

2. We, HDANYWHERE warrant to you, the end user [MG1] of the HDA hardware (the “Products”) that on the date of
delivery of the Products to you, and for a period of 2 years from that date of delivery, the Products shall:

(a) match any description that has been provided to you;

(b) be free from any signicant defects in their design, the materials used to make them, and the way they are

made;

(c) be of satisfactory quality (within the meaning of the Consumer Rights Act 2015); and
(d) be t for any purpose held out by us.
This 2 year period, or, if the period has been extended to 3 years in accordance with paragraph 3, will be the
“Guarantee Period”. We offer this guarantee to all our customers who are resident and have an address in Great

Britain and Northern Ireland. [MG2]

EXTENDING YOUR GUARANTEE

3. On registering your Products with the HDA Cloud, the guarantee offered in paragraph 2 by us will automatically
extend for a period of one year, provided that your registration takes place within 30 days from the date of delivery.
The one year guarantee extension starts automatically from the date that the original 2 year guarantee ends.

HOW TO CLAIM ON YOUR GUARANTEE AND YOUR REMEDIES

4. Subject to paragraphs 5 and 6 of this guarantee, Your sole remedies under Our guarantee to You are as follows:
(i)Up to 30 days: we will repair or replace your Products or provide you with a full refund of the price of the defective
Products at your option.
(ii) Up to 6 Months: we will repair or replace your Products. If we are unable to repair or replace your Products we
will provide you with a full refund of the price of the defective Products.
(iii) Up to 2 (3) Years: we will repair or replace your Products. If we are unable to repair or replace your Products
we will provide you with a partial refund of the price of the defective Products based upon the devaluation of the
Products since the time of purchase.

5. In order to claim under the guarantee given to you in paragraph 2 you will need to:
(a) give us notice in writing of your intention to claim under the guarantee during the Guarantee Period, and do
so within a reasonable time after nding that some or all of the Products do not comply with the guarantee set out
in paragraph 2;
(b) show that the Products that you claim are defective, have been examined by a HDA Pro or other authorised or
suitably qualied installer, and that they have[MG3] conrmed in writing that the suspected defect in the Products

stems solely from a fault in the HDA hardware;

(c) give us a reasonable opportunity to examine the Products in question;
(d) provide us with an order number and a dated sales or delivery receipt from an HDA Distributor, HDA Pro or other
authorised dealer, reseller or installer of the Products.
(e) obtain from us in advance of returning the Products a return merchandise authorisation and/or case

number[MG4] ; and

(f) (if asked to do so by us) return such Products to our place of business at our cost.

CIRCUMSTANCES WHERE YOUR GUARANTEE DOESN’T APPLY

6. We shall not be liable for the Products’ failure to comply with the guarantee set out in paragraph 2 in any of the
following events:

(a) If you make any further use of the Products after giving us notice of an issue in accordance with paragraph 5;
(b) the defect arises because you failed to follow our oral or written instructions as to the storage, installation[MG5]
, use and maintenance of the Products;

(c) the defect arises as a result of your use of the Products with any other software or hardware that is not
compatible with the Products;
(d) the products are used by you for any commercial purpose, including rental or demonstrative purposes;
(e) you alter or repair the Products without the written consent of HDA;
(f) the defect arises as a result of an act of god, fair wear and tear, or your misuse, abuse, unreasonable use, wilful
damage, negligence, or abnormal storage of the Products or by any other causes unrelated to defective hardware
or manufacturing;
(g) where the serial number has been altered, defaced or removed;

(h) where the warranty seal on the system has been altered, defaced or removed; or

(i) where the Products differ from their description as a result of changes made to ensure they comply with
applicable statutory or regulatory requirements.

TRANSFERRING YOUR GUARANTEE TO SOMEONE ELSE

7. HDA will not accept any liability under such guarantee unless you are the original customer or can produce a
letter or chain of letters from the original customer and subsequent customers (where appropriate) transferring the
benet of the guarantee to you.

PRODUCTS THAT ARE NOT COVERED BY THIS GUARANTEE

8. This guarantee does not cover products sold and clearly marked “as is”, “B-grade”, or with faults. This guarantee

does not apply to any system software that is preinstalled in the HDA hardware, or is subsequently provided via

update or upgrade releases. Any and all HDA software is licensed to you under the terms of a separate end user
licence agreement found here: https://hdanywhere.com/legals

HOW THIS GUARANTEE WORKS WITH OUR EULA

9. We may void this guarantee if we reasonably believe that the HDA system has been used in a manner that
violates terms of our separate End User Licence Agreement (EULA) for the HDA software. You assume all-risk and
liabilities associated with the use of third party products in conjunction with the Products.

YOUR STATUTORY RIGHTS

10. This guarantees is in addition to your statutory rights (including under the Consumer Rights Act) which are not
affected by this guarantee

GENERAL TERMS OF THIS GUARANTEE

11. Except as provided in this guarantee, we shall have no liability to you in respect of the Products’ failure to
comply with the guarantee set out in paragraph 2.

12. We reserve the right to amend or withdraw this guarantee at any time although for the avoidance of doubt any
guarantees that are in existence at such a time will be honoured.

13. These Conditions shall apply to any repaired or replacement Product supplied by us.

GUARANTEE CONTACT INFORMATION

To contact ([e-mail]) or call HDANYWHERE Technical Support (call charges will depend on your
telephone provider. Please check with your operator for exact charges).

The team is available 9am - 5pm weekdays.
To help us handle your query promptly, please have your invoice number and model SKU and serial ready.

41

Let us know what you think.

We would love to hear how we could further improve our products and services.

If we can make something better, please let us know!

[e-mail]

Copyright © HDANYWHERE.

HDANYWHERE

Registered in England & Wales 06046737 VAT 913222367

HDANYWHERE assumes no responsibility for any inaccuracies that may be contained in this document. In no event

will HDANYWHERE be liable for direct, indirect, special, incidental, or consequential damages resulting from any
defect or omission in this document, even if advised of the possibility of such damages.

TM

is a trading name of HD Connectivity Ltd.