HCS KWR1018M0 Users Manual

Philips Home Control

Manual of KWR101830/01B, KWR101830/01BS &

KWR101830BU

Confidential

©Philips Home Control,

2013

Page 1 of 14

Philips Home Control

FCC Statement

FCC Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

No special accessory is required to enable the equipment to comply with the emission
limits.

Confidential

©Philips Home Control,

2013

Page 2 of 14

KWR101830/01B

Manual (Draft Version)

1. Product Description

1.1 Product Features

• Dual button entry RC and KWR.

• Number of keys: 38 for KEYBOARD, 18 for RC. Total 56 keys.

• 4 main functions: Remote Control, Mouse Cursor Control, Qwerty KEYBOARD for text entry and

downstream data transfer.

• 128k Flash for handling RF functions.

• 6 axis motion pointing.

• IR Learn using Data Flash.

• IR Database.

• IR uses Flash chip.

• Low voltage alert through LED blinks.

• Works with USB Receiver dongle OVU810006.

Status :Draft, For Review

Philips Home Control Company Restricted

Page 3 of 14

Philips Proprietary &Confidential

KWR101830/01B

y

1.2 Product

Manual (Draft Version)

Picture for illustration onl

Status :Draft, For Review

Philips Home Control Company Restricted

Page 4 of 14

Philips Proprietary &Confidential

KWR101830/01B

Manual (Draft Version)

2. RF Functions

2.1 RF Pairing

1) Make sure RC is within 1m distance from the STB and no other RF RCs are present.

2) Make sure the Qwerty keyboard faces upwards.

3) Press and hold Keyboard W and Keyboard O keys together for at least 5 seconds.

4) The KEYBOARD LED will start blinking, and RC is now in pairing mode.

5) Activate pairing mode on STB (STB sends activate command or reset dongle power).

6) Once the pairing is successful, the KEYBOARD LED will be turned off; otherwise, the KEYBOARD
LED will stay lit till timeout.

There will be a 30 seconds timeout for RC to be in pairing mode. Previously paired receiver shall be
retained as long as the STB did not initiate the pairing. See Note below on different pairing scenarios.
User can start from Step 1 again if pairing failed.

Note:

When a previously paired RC starts pairing with

1. Different receiver
o Only upon successful pairing, the RC shall replace the previously paired receiver with the new
receiver.
o If the pairing process fails or pairing timeout occurs, the previously paired receiver will be retained.

2. Same receiver
o Previously paired information of the same receiver shall first be erased from the RC before pairing
process starts.
o If the pairing process fails or pairing timeout occurs, the previously paired receiver will not be
retained.

At any one time,
 Only one RC is allowed to be in pairing mode, i.e. no concurrent pairing is allowed.

 Each RC can only work with one receiver, i.e. 1-to-1 pairing.

2.2 RF Un-Pairing

The following steps for un-pairing:

1) Make sure the Qwerty keyboard faces upwards.

2) Press and hold Keyboard X and Keyboard UP keys together for at least 5 seconds.

3) The KEYBOARD LED will start blinking slowly after 5 seconds.

4) Reset the power or battery and the RC is ready to pair again.

2.3 Remote Idling, RF Link Timeout with connection

When detected no activity, the RC will enter SLEEP mode. During SLEEP mode, RF link will be
disconnected to preserve power. Pressing any key or any gesture action will resume the RC to
ACTIVE mode almost immediately. The key-press that resumes the RC from SLEEP mode will be
remembered and transmitted.
When the RC wakes up from SLEEP mode, there may be reconnection latency depending on the RF
link condition with the receivers.

Once the RF (2.4G) link has been established, the RC will execute upon ANY key-press. Key presses

prior to successful RF link connection will not be transmitted.

Status :Draft, For Review

Page 5 of 14

Philips Home Control Company Restricted

Philips Proprietary &Confidential