HBC HD-uDTA Setup Instruction

HD-uDTA Setup Guide

What’s included in your install kit?

[phone] • www.hbci.com

1 2

3

4

5

6

7 8

9

0

GUIDE

INFO

MENU

EXIT

PAGE

MUTE

TV CABLE

POWER

LAST

L

A

N

G

Remote

In order to operate the HD-

uDTA you must use the
remote control included

with this kit. Programming

instructions for the remote are

included in this guide.

Coaxial Cable

A 5-foot cable is provided in

your installation kit.

Note: For high-denition

viewing an HDTV and HDMI

cable are required. Please

contact your local ofce to

purchase an HDMI cable.

Power Cord

The power cord will need to be

plugged into a non-switched

outlet to operate your HD-

uDTA.

Velcro Squares

For out of site placement, use
the Velcro squares to stick the

HD-uDTA to your TV.

Note: HBC is not responsible

for any damage as a result

of use.

2 AA Batteries

2 AA batteries are included in

your installation kit.

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

Connect a coaxial cable to the

TO TV connector on the HD-

uDTA and the Cable/Antenna

IN on the TV.

Note: Each TV will need to be connected to an HBC

HD-uDTA or a HBC set-top box, but not both.

For high-denition viewing,

connect an HDMI cord to

the HDMI input on both your

HDTV and HD-uDTA

HD-uDTA

(High-Denition Digital Transport Adapter)

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

051717

Using your Remote Control:Programming your HD-uDTA Remote:

Your remote control is simple to program, easy-to-use, and
can operate two (2) electronic devices, which include:

• HD-uDTA - Motorola HD (High-Denition) Universal
Digital Transport Adapter

• TV - Television

1. Turn on the TV by pressing the POWER button on
your television set.

2. On your remote, press SETUP until LED blinks twice.

3. Pressing the TV POWER , the LED should remain on.

4. Press the numbered button listed for your TV brand
(example: press the 6 button for all Samsung TVs).

- 1 = Insignia/Dynex

- 2 = LG/Zenith

- 3 = Mitsubishi

- 4 = Panasonic

- 5 = Philips/Magnavox

- 6 = Samsung

- 7 = Sharp

- 8 = Sony

- 9 = Toshiba

- 0 = Vizio

5. Let go of the numbered key when your TV turns off and
setup is complete.

- Before you can use your remote control, it must be
programmed (setup) to operate your TV. Two (2) blinks
from the LED light means setup was a success, one (1)
long blink means setup was not successful. If the “Remote
Control User’s Guide” code book was not provided in your
installation kit or you no longer have it, please visit

www.hbci.com/support to download the “HBC Remote

Control Handbook.” If your TV screen is blank or you have

no sound, you may have not completed all of the installation
and activation steps. Please ensure each step of the
installation and activation has been completed. If problem(s)
still persist, please contact Wizards Technical Support at

[phone] and press 2 on your phone’s keypad when

prompted.

Important Handling and Installation Instructions:

• Install the HD-uDTA away from heat sources such as radiators, heat registers, and stoves.

• Do not operate the HD-uDTA in extreme weather conditions.

• Do not place the HD-uDTA in an enclosed area where the cooling vents are blocked or

impede the ow of air through the ventilation openings.

• Position the HD-uDTA with at least 3 inches of space on all sides.

• Place the HD-uDTA on a at surface that is not prone to vibration or impact.

• Do not install the HD-uDTA in an area where condensation occurs.

1 2

3

4

5

6

7 8

9

0

GUIDE

INFO

MENU

EXIT

PAGE

MUTE

TV CABLE

POWER

LAST

L

A

N

G

Turns TV ON/OFF

Displays main MENU

Displays program GUIDE

Controls TV VOLUME

Used in the program guide
for PAGE navigation

Turns set-top box ON/OFF

Displays INFO for currently

selected program

EXITs current menu and
returns to current program

Returns to LAST channel

you were watching

HOLD for 3 seconds to enter SETUP

Channel UP/DOWN

Change or setup primary
audio language (SAP)

Used to navigate
on-screen guide

MUTEs TV VOLUME

Used to make a selection on

the on-screen guide

Connect the HD­uDTA to your cable
service.

A) Locate the coaxial
cable that currently
runs from the cable
wall outlet to the back
of your TV. Leave
one end of the cable
connected to the wall,
but disconnect the other
end from the back of
your TV.

B) Connect the coaxial
cable from your wall
outlet to the input on the
back of the HD-uDTA
labeled CABLE IN.

Connect the HD­uDTA to your TV.

A) Locate the supplied
coaxial cable provided
in your installation kit.
Connect one end of
the coaxial cable to the
input labeled TO TV on
the back of the HD­uDTA.

B) Connect the other
end of the cable to the
input labeled ANT/

CABLE on the back of

your TV.

Turn on the HD­uDTA.

A) Plug the round end
of the power cord into
the +5V DC IN input on
the back of the HD­uDTA.

B) Plug the other end
into a non-switched
wall outlet. The HD­uDTA will turn on
automatically.

Set the channel.

A) Turn on your TV and
tune it to channel 3 or 4.

B) Set the switch on the
back of the HD-uDTA to

CH 3 or CH 4.

Activate the HD­uDTA.

A) If you received more
than one HD-uDTA from
HBC, you must connect
all of them before
calling to activate.

B) Ensure your HD­uDTA remote control
has been programmed
for your TV.

Note: For more
information on
programming your
remote, please refer
to the section titled

“Programming Your
HD-uDTA Remote,”

located on the back of
this guide.

C) To complete your
activation please call
Wizards Technical
Support at

[phone] and

press 2 on your phone’s
keypad when prompted.

Conrm your

service.

A) After activating wait a
few minutes.

B) Make sure your TV is
turned on.

C) Conrm that the

HD-uDTA is connected
to the power outlet and
that the green light on
the front is solid (not
blinking).

D) Using the remote

control to operate
your HD-uDTA, scroll
through your channels
and make sure they are
all working.

Note: If the light
is blinking, or
your channels are
not showing up,
please refer to the

“Troubleshooting”

section of this guide.

Installation and Activation: TV

1 2 3 4 5 6

TV

A

CABLE/ANTENNA IN

Cable Wall Outlet

Disconnect

TV TV

B

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

Cable Wall Outlet

DTA

B

Reconnect

CABLE IN

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

Cable Wall Outlet

A

CABLE IN

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

A

CABLE IN

DTA D TA

Cable Wall Outlet/Power Outlet

+5V DC IN

B

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

DTA

CH 3/4

B

A

Channel 3

TV

1 2

3

4

5

6

7 8

9

0

GUIDE

INFO

MENU

EXIT

PAGE

MUTE

TV CABLE

POWER

LAST

L

A

N

G

D

B

C

Connect the HD­uDTA to your cable
service.

A) Locate the coaxial
cable that currently
runs from the cable
wall outlet to the back
of your HDTV. Leave
one end of the cable
connected to the wall,
but disconnect the other
end from the back of
your HDTV.

B) Connect the coaxial
cable from your wall
outlet to the input on the
back of the HD-uDTA
labeled CABLE IN.

Connect the HD­uDTA to your TV.

A) Connect the HDMI
cable to the HDMI input
on the back of the HD­uDTA.

B) Connect the other
end of the cable to the

HDMI input on the back

of your HDTV.

Turn on the HD­uDTA.

A) Plug the round end
of the power cord into
the +5V DC IN input on
the back of the HD­uDTA.

B) Plug the other end
into a non-switched
wall outlet. The HD­uDTA will turn on
automatically.

Set the channel.

A) Tune to the HDMI
input that the HD-uDTA
is plugged in to.

Activate the HD­uDTA.

A) If you received more
than one HD-uDTA from
HBC, you must connect
all of them before
calling to activate.

B) Ensure your HD­uDTA remote control
has been programmed
for your HDTV.

Note: For more
information on
programming your
remote, please refer
to the section titled

“Programming Your
HD-uDTA Remote,”

located on the back of
this guide.

C) To complete your
activation please call
Wizards Technical
Support at

[phone] and

press 2 on your phone’s
keypad when prompted.

Conrm your

service.

A) After activating wait a
few minutes.

B) Make sure your
HDTV is turned on.

C) Conrm that the

HD-uDTA is connected
to the power outlet and
that the green light on
the front is solid (not
blinking).

D) Using the remote

control to operate
your HD-uDTA, scroll
through your channels
and make sure they are
all working.

Note: If the light
is blinking, or
your channels are
not showing up,
please refer to the

“Troubleshooting”

section of this guide.

Installation and Activation: HDTV

1 2 3 4 5 6

TV

A

CABLE/ANTENNA IN

Cable Wall Outlet

Disconnect

TV TV

B

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

Cable Wall Outlet

DTA

B

Reconnect

CABLE IN

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

A

CABLE IN

DTA

Cable Wall Outlet/Power Outlet

+5V DC IN

B

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

DTA

HDMI

B

A

HDMI

TV

1 2

3

4

5

6

7 8

9

0

GUIDE

INFO

MENU

EXIT

PAGE

MUTE

TV CABLE

POWER

LAST

L

A

N

G

CABLE IN TO TV

CH 3/4

HDMI

+5V DC In

Power

Cable Wall Outlet

A

CABLE IN

DTA

D

B

C