Hayward Pools S244SV, S210SV User Manual
Your Hayward Pro Series high-rate sand filter is a high
performance, totally corrosion-proof filter that blends
superior flow characteristics and features with ease of
operation. It represents the very latest in high-rate sand
filter technology. It is virtually foolproof in design and
operation and when installed, operated and maintained
according to instructions, your filter will produce clear,
sparkling water with only the least attention and care.
HOW IT WORKS
Your filter uses special filter sand to remove dirt particles
from pool water. The filter sand is loaded into the filter tank
and functions as the permanent dirt removing media. The
pool water, which contains suspended dirt particles, is
pumped through your piping system and is automatically
directed by the patented filter control valve to the top of the
filter tank. As the pool water is pumped through the filter
sand, dirt particles are trapped by the sand bed, and filtered
out. The cleaned pool water is returned from the bottom of
the filter tank, through the control valve and back to the pool
through the piping system. This entire sequence is
continuous and automatic and provides for total recirculation
of pool water through your filter and piping system.
After a period of time, the accumulated dirt in the filter
causes a resistance to flow, and the flow diminishes. This
means it is time to clean (backwash) your filter. With the
control valve in the backwash position, the water flow is
automatically reversed through the filter so that it is directed
to the bottom of the tank, up through the sand, flushing the
previously trapped dirt and debris out the waste line. Once
the filter is backwashed (cleaned) of dirt, the control valve is
manually resequenced to Rinse, and then Filter, to resume
normal filtering.
INSTALLATION
Only simple tools (screwdriver and wrenches), plus pipe
sealant for plastic adapters, are required to install and/or
service the filter.
The filter system should be installed, not more than 6
feet above pool water level, on a
level
concrete slab,
very firm ground, or equivalent, as recommended by
your pool dealer. Position the filter so that the piping
connections, control valve and winter drain are
convenient and accessible for operation, service and
winterizing.
Assemble filter control valve to filter. Align the two (2)
valve pipe connections, with O-rings in place, with the
two openings in the side of the filter tank and press in
firmly . Secure the assembly to the tank connections with
the two bulkhead locknuts.
Do not overtighten.
1.
2.
IS210SV-99
MODELS S210SV, S244SV
23-1/2”
(60 cm)
35-3/4” (91 cm) S210SV
40” (102 cm) S244SV
SPECIFICATIONS
MODEL
NUMBER
S210SV
S244SV
EFFECTIVE
FILTRATION AREA
FT
2
2.2
3.14
M
2
0.21
0.3
GPM
44
62
LPM
167
235
PSI
2
3
PSI
50
50
BAR
0.14
0.21
BAR
3.45
3.45
INCH
18
18
INCH
18
18
MM
457
457
MM
457
457
LBS
200
300
KGS
91
136
FILTER SAND**
0.45-0.55
0.45-0.55
DESIGN
FLOW RATE*
PRESSURE LOSS AT
DESIGN FLOW RATE
MAXIMUM WORKING
PRESSURE
REQUIRED CLEARANCE
SIDE ABOVE
MEDIA REQUIRED
TYPE AMOUNT
PARTS
Models S210SV, S244SV
*Based on 20 GPM/ft.2or 814 LPM/m2(maximum allowable NSF rating).
**Also known as No. 20 or No. 1/2 Silica Sand.
NOTE: ANSI/NSPI-4 Article V, standard for
above-ground and on-ground pools, advises that
components such as the filtration system, pumps
and heater be positioned so as to prevent their
being used as a means of access to the pool by
young children.
REF.
NO.
1
2
3
4
5
6
7a
7b
8
9a
9b
10a
10b
11a
11b
12
13a
13b
14
15
16
17
18
19
20
21
NO.
REQ’D.
1
1
1
1
1
1
1
1
1
1
1
1
10
1
1
1
1
1
1
2
2
1
2
PART NO.
ECX270861
DEX2400S
SX200Z5
SX244K
GMX600F
GMX600NM
SX210AA2
SX244AA2
SX244G
SX210CD
SX244CD1
SX210CD2
SX244CD2
SX200Q
SX240D
SX240MA
CX3000Z2
CX1100Z4
SX200Z2
SX180G
SX180H
SX200J
SX220Z3
SX244P
SPX410X602S
SX200Z4
DESCRIPTION
Pressure Gauge
Manual Air Relief Cap
O-Ring, 13/16” O.D.
Top Closure Dome
Valve/Tank O-Ring
Flange Clamp (Valve-Tank)
Filter Tank (S210S)
Filter Tank (S244S)
Top Diffuser
Top Elbow Assembly (S210S)
Top Elbow Assembly (S244S)
Bottom Elbow Assembly (S210S)
Bottom Elbow Assembly (S244S)
Lateral (S210S)
Lateral (S220S, S244S)
Lateral Holder Assembly
Plastic Air Tube (S210S)
Plastic Air Tube (S244S)
Air Tube Lock Screw
Gasket
Drain Cap
Filter Support Stand
O-Ring
Bulkhead Fitting
Slide Control Valve
O-Ring
a
b
Loading...