Hayward Pools ISCC100 User Manual

ISCC100

Rev. D

____________________________________________________________________________________

OWNER’S MANUAL

INSTALLATION, OPERATION, & PARTS

XStream™ Filtration Series

The Hayward® XStream™ Filtration Series is specifically designed for the demanding requirements of today’s above-ground
swimming pools. The advanced design reduces maintenance requirements while providing superior performance.

To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.

CAUTION – We highly recommend a qualified professional install and service this product.

WARNING – This manual contains important safety information that must be furnished to the end

user of this product. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY.

SAVE THIS INSTRUCTION MANUAL

HAYWARD POOL PRODUCTS, INC.

Corporate Headquarters: U.S.A:
620 Division Street 1 Hayward Industrial Drive 2935 Sidco Drive 2875 Pomona Blvd.
Elizabeth, NJ 07207 Clemmons, NC 27012 Nashville, TN 37204 Pomona, CA 91768

Canada: Europe:
2880 Plymouth Drive Parc Industriel de la plaine de l'Ain

01150 Saint Vulbas
France

Oakville, Ontario L6H 5R4 Allêe des Chênes

XStream™ Filtration Series__________ _______________

(

)

PRODUCT REGISTRATION

DATE OF INSTALLATION ____________________

INITIAL PRESSURE GAUGE READING (CLEAN FILTER) _______________________

PUMP MODEL ________________ HORSEPOWER _______________________

FILTER MODEL ________________ SERIAL NUMBER _______________________

Retain For Your Records

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety precautions should always be

followed, including the following: Failure to follow instructions may result in injury.

READ AND FOLLOW ALL INSTRUCTIONS

IN THIS OWNER’S MANUAL AND ON

EQUIPMENT.

KEEP SAFETY LABELS IN GOOD CONDITION AND

REPLACE IF MISSING OR DAMAGED.

WARNING – To reduce risk of injury, do not permit children to use or climb on this

product. The ANSI/NSPI 4 Standard (above-ground and on-ground pools) advises that
components such as the filtration system, pumps, and heaters be positioned to prevent their being
used as a means of access to the pool by young children. Closely supervise children at all times.

CAUTION – The XStream™ Filtration Series is intended for use on permanently installed

above-ground swimming pools and may also be used with hot tubs and spas if so marked. Do
NOT use with storable pools. A permanently installed pool is constructed in or on the ground or
in a building such that it cannot be readily disassembled for storage. A storable pool is
constructed so that it is capable of being readily disassembled for storage and reassembled to its
original integrity.

Though this product is designed for outdoor use, it is strongly advised to protect the electrical
components from the weather. Select a well-drained area, one that will not flood when it rains. It
requires free circulation of air for cooling. Do not install in a damp or non-ventilated location.

Bond motor to pool structure. Use a solid copper conductor, size or larger. Run wire from
external bonding lug to reinforcing rod or mesh. Connect a No. 8 AWG (8.4 mm²) solid copper
bonding wire to the pressure wire connector provided on the motor housing and to all metal parts
of swimming pool, spa, or hot tub, and to all electrical equipment, metal piping or conduit within
5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub. (In Canada use No. 6 AWG
bonding wire.)

XStream™ Filtration Series __________ _____________________________________

NOTE: The National Electrical Code (NEC) permits use of a cord with a maximum 3 ft.
(1 m) length. If your pump is equipped with a cord complying with the NEC, the following three
(3) items apply.

WARNING – Risk of Electric Shock. Connect only to a grounding

type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). Contact a
qualified electrician if you cannot verify that the receptacle is protected by a
GFCI.

WARNING – To reduce the risk of electric shock replace damaged cord

immediately. Do NOT bury cord. Locate cord to minimize abuse from lawn

mowers, hedge trimmers and other equipment.

WARNING – To reduce the risk of electric shock, do NOT use an extension cord to

connect unit to electric supply. Provide a properly located outlet. Qualified personnel MUST do
all electrical wiring.

CAUTION – All suction and discharge valves MUST be OPEN when

starting the filter system. Failure to do so could result in severe personal injury
and/or property damage. All drains and suction covers MUST have properly
installed covers securely attached with the screws supplied with the covers. If
screws are lost, order replacement parts from your supplier.

DANGER – Suction Entrapment Hazard. Never use the pool or

spa if a drain cover is damaged, cracked, missing, or not securely attached. Suction in drains and
suction outlets can cause drowning, disembowelment, hair or body entrapment, severe injury, and
death. Disembowelment, entrapment, or drowning is possible when body parts or hair come in
contact with damaged, broken, cracked, missing, or unsecured drain covers and suction outlets.
Suction from pumps with only one drain or suction outlet can cause disembowelment,
entrapment, or drowning. Pumps for pools and spas require two (2) functioning suction outlets at
least three (3) feet apart, on two (2) walls or on the floor and one (1) wall of the pool or spa.
Installation of pump and suction outlets must be in compliance with all applicable local building
codes. Replace damaged, broken, cracked, missing, or unsecured drain covers and suction outlets
immediately.

WARNING – Hazardous Pressure. Pumps, filters, and other

equipment/components of a swimming pool filtration system operate under pressure. Incorrectly
installed and/or improperly tested filtration equipment and/or components may fail resulting in
injury and/or property damage. A qualified pool professional MUST conduct all pressure tests.
This product is intended for above-ground/on-ground swimming pool applications only. Do NOT
connect to a high-pressure system such as a municipal water main. To prevent explosion caused
by entrapped air in the filtration system use provided air relief valve to bleed air from the system.
Confirm that ALL filtration system component clamps, bolts, and covers have been tightened to
the manufacturer’s recommendations.

WARNING – Never operate or test the filtration system at more than 30 PSI.

SAVE THESE INSTRUCTIONS