Hayward Ultra-Pro LX, Ultra-Pro LX SP2290, Ultra-Pro LX SP2290T, Ultra-Pro LX SP-2295, Ultra-Pro LX SP-2295T Installation And Operating Instructions Manual

IS-2290-02-HC

HAYWARD Hi-Performance SELF-PRIMING PUMPS

INSTALLATION AND OPERATING INSTRUCTIONS

GENERAL TIPS ON PUMP INSTALLATION

For best pump performance, locate the system below
the pool water line and as close to the pool as possible.

If you own an above ground pool please see Note: NSPI­4 Article V, for safe and proper installation of the
equipment package. Make sure suction joints are tight.

Suction pipe should be as large or larger than discharge
pipe.

Damp, non-ventilated locations should be avoided.
Motors require free circulation of air to aid in cooling.

Insure that the electrical supply available agrees with the
motor's voltage, phase and cycle, and that wire size is
adequate for the HP/KW rating and distance from the
power source. Motor must always be properly grounded.
If cord connected, use only a properly grounded outlet.
Electrical circuits should be protected by proper size
ground fault circuit interrupter (GFCI). All electrical wiring
should be performed by qualified personnel and must
conform to local codes and regulations.

STARTING AND PRIMING INSTRUCTIONS

Fill strainer/housing completely with water. Never
operate the pump without water. Water acts as a coolant
and lubricant for the mechanical shaft seal.

Open all suction and discharge lines and valves, as well
as air bleed (if available) on filter. (The air that is to be
displaced from the suction line must have some place to
go).

Turn on power and allow a reasonable time for priming.
Priming time depends on suction lift and length of
suction piping. If pump will not start, or will not prime, see
TROUBLE SHOOTING GUIDE on back page.

Note: NSPI-4 Article V, standard for above ground and
on ground pools, advises that components such as the
filtration system, pumps and heater be positioned so as
to prevent their being used as a means of access to the
pool by young children.

Your Hayward Ultra-Pro LX pump has been quality-built
and engineered to give you many years of efficient,
dependable service. The non-conductive, corrosion-proof
motor housing provides protection from the elements and
insulates the electrical motor parts from outside contact.

The advanced design reduces operation and maintenance
to simple, common-sense procedures.

MAINTENANCE

1. Clean strainer basket regularly. Do not strike basket
to clean. Inspect strainer cover gasket regularly and
replace as necessary.

2. Hayward pumps have self-lubricating motor bearings
and shaft seals. No lubrication is necessary.

3. Keep motor housing clean. Insure air vents are free
from obstructions, debris, etc.

4. Occasionally, shaft seals must be replaced, due to
wear or damage. See instructions

STORAGE/WINTERIZING

Pump and motor must be protected from freezing. Shut
off all electric power. Disconnect cord/electrical
connections and plumbing connections. Drain
thoroughly and clean out any debris. Store pump and
motor in a dry, well ventilated room.

HAYWARD POOL PRODUCTS CANADA, INC.

2880 PLYMOUTH DRIVE, OAKVILLE, ONTARIO L6H 5R4 • [phone]

® Hayward Pool Products Canada, Inc. – Licensee

PART NUMBER

Ref. DESCRIPTION No. MODEL MODEL

No. Req'd SP2290 (T) SP-2295 (T) (ET)

1 Strainer Cover 1 SP1500D2A SP1500D2A
2 Strainer Cover w/O-ring 1 SP1500P SP1500P
3 Basket 1 SP1500LX SP1500LX
4 Strainer Housing 1 SP1500CP SP1500CP
5 Drain Plug (optional) – SP1700FG SP1700FG
6 Drain Plug w/Gasket 1 SP1700FG SP1700FG
7 O-ring 1 SP1500W SP1500W
8 Bolt, No.10-24 Hex. Head 8 SP1500N2 SP1500N2

9 Housing Cover 1 SP1580BP SP1580BP
10 Housing O-ring 1 SP1580Z1 SP1580Z1
11 Impeller 1 SP1500E SP1500F
12 Seal Assembly 1 SP1500KA SP1500KA
13 Pump Housing 1 SP1580AAP SP1580AAP
14 Nut, No. 10-24 Hex. 8 SP1500Y2 SP1500Y2
15 Shaft Sleeve 1 SP1500Q2 SP1500Q2
16 Motor 1 SP1509ZIUF SP1514ZIUF
17 Shroud 1 SP2090B SP2090B
18 Motor Housing 1 SP2090A SP2090A

19a Timer End Cover (Mechanical) (T) 1 SP1500TI SP1500TI
19b Timer End Cover (Electronic) (ET) Optional – SP2090CET

20 Motor-To-Housing Bolt 4 To order, specify manufacturer, HP and Model No.
21 Elevated Mounting Base Optional SP2601C SP2601C
22 Motor End Cover Optional SP2090C SP2090C
23 Switch Assembly Optional EC1325 EC1325
24 Power Cord 1 SP1550WA7C SP1550WA7C