Hayward MakoShark 2, Tiger Shark 2 Plus, KingShark, KingShark 2 w/Remote, KingShark 2 Owner's Manual
...
ISRC9403RevB
KingShark2
2
Limited Warranty
MakoShark 2
KingShark
KingShark 2
KingShark 2 w/Remote
TigerShark 2
Tiger Shark 2 Plus
Your Hayward Pool Cleaner has been manufactured, tested and inspected in accordance with carefully specified
engineering requirements. It is warranted to be free from defects in materials and workmanship for a period of one year.
Coverage is provided to the original owner only and is not transferrable. This limited warranty includes both parts and labor
for the cleaners listed above. This warranty gives you specific legal rights. You may also have other rights, which vary from
state to state
EXCEPTIONS AND EXCLUSIONS FROM WARRANTY
Damage, malfunctions or other failures of the cleaner arising from improper electrical supply levels are excluded
from this warranty. Malfunctions, failure or damage of the cleaner caused by improper, unreasonable, or negligent use or
abuse by the consumer, are excluded from this warranty.
Any repair that is made on your cleaner during the warranty period by anyone other than an Authorized Hayward
Warranty Service Center (designated to perform such work) will void this warranty and other warranty rights you may have.
Filter cartridges and debris bags are not covered by this warranty
INSTRUCTIONS TO OBTAIN WARRANTY REPAIR
To obtain repair of your Hayward cleaner under this warranty, the following procedure must be followed:
• Locate and deliver the cleaner to the nearest Hayward Factory Authorized Warranty Service Center. Your Authorized
Hayward Warranty Service Center can be located by visiting www.haywardnet.com
locate you nearest authorized service center. Cost of transportation, if required, is at the sole expense of the owner. Proof
of purchase is required.
TERMS
If a warranty claim is made and the product delivered to an Authorized Hayward Warranty Service Center within the
warranty period, your Hayward cleaner will be repaired at no charge (parts & labor) to you. Listed warranty exclusions
apply.
No dealer, distributor, or other similar person has any authority to make any warranties or representations
concerning Hayward Pool Cleaner products or to extend this warranty beyond the express items contained herein.
Accordingly, Hayward Pool Products assumes no responsibility for any such warranties or representations beyond the
express items contained in this limited warranty.
WARRANTY REGISTRATION CARD
You can register your unit on-line by visiting www.Haywardnet.com
card and returning it to:
Hayward Industries
Attn Warranty Department
620 Division Street
Elizabeth, NJ 07207
. You may also call 908-355-7955 to
or by filling out the registration
KingShark2
CONTENTS
Safety Precautions ................................................................2
General Information ...............................................................3
Motor Information ..................................................................4
Trouble Shooting ...................................................................5
Specifications ........................................................................7
Machine Assembly/Parts .......................................................8
Filter Assembly/Parts ...........................................................10
Accessories .........................................................................11
Preventive Maintenance ......................................................13
Parts Ordering Instructions ..................................................14
Rev. 3/10
1
KingShark2
SAFETY PRECAUTIONS
The KingShark2 automatic swimming pool vacuum cleaner has been
manufactured with the highest degree of care and concern
for safety. We suggest the following safety precautions become part of your
pool safety regulations:
ALWAYS PUT THE MACHINE INTO THE WATER BEFORE CON-
1.
NECTING IT TO THE ELECTRICAL OUTLET.
2. IT IS IMPORTANT FOR SWIMMERS’ SAFETY TO REMOVE
THE UNIT IMMEDIATELY FOLLOWING USE. THIS WILL ALSO
IMPROVE THE OPERATING LIFE OF YOUR KINGSHARK2.
3. BE CERTAIN THE MACHINE IS ONLY PLUGGED INTO A
GROUNDED ELECTRICAL OUTLET EQUIPPED WITH A
GROUND FAULT CIRCUIT INTERRUPTER.
4. DO NOT HANDLE MACHINE WHILE IT IS PLUGGED INTO THE
ELECTRICAL OUTLET.
5. DO NOT USE AN EXTENSION CORD. THIS COULD CREATE A
SAFETY HAZARD AND/OR DAMAGE YOUR UNIT.
6. ALWAYS STAY OUT OF THE POOL WHILE CLEANER IS IN
OPERATION.
7. NEVER ALLOW PLUG TO ENTER THE POOL.
8. DO NOT OPERATE THE MACHINE OUT OF WATER. THIS WILL
DAMAGE THE MOTOR SEAL AND VOID THE WARRANTY.
9. DO NOT DRAG THE MACHINE OUT OF THE POOL AGAINST
THE SIDE WALL. THIS COULD DAMAGE UNIT AND/OR YOUR
POOL WALL.
10. SOME POOLS HAVE A CORNER OR A CORNER STEP CONFIGURATION THAT MAY CAUSE THE UNIT TO “HANG-UP;”
THEREFORE, DO NOT LEAVE THE UNIT COMPLETELY
UNATTENDED FOR MORE THAN 1/2 HOUR. OCCASIONAL
OBSERVATION AND ATTENDANCE CAN ALSO REDUCE ANY
TENDENCY FOR THE CORD TO TWIST.
While the KingShark2 has been made to operate as safely as possible,
we suggest you exercise reasonable care in the handling of the vacuum and
inspect the electrical cord frequently for damage or wear, as with any other
electrical appliance. After use, remove the unit and rinse with fresh water and
remove any twists that may be present in the cord.
2
KingShark2
GENERAL INFORMATION
You have purchased the finest piece of equipment in the pool cleaner industry. If you
treat it as such, your KingShark2 automatic swimming pool vacuum cleaner will give you
years of satisfactory service. As a suggestion, the unit should be stored in the original
shipping container for safekeeping during the off season.
ADJUSTMENT
THERE IS ONE ADJUSTMENT THAT MAY BE NECESSARY FOR USE IN YOUR
POOL. PLEASE TAKE THE FEW MINUTES NECESSARY TO UNDERSTAND THIS
SIMPLE PROCEDURE:
The height of the sensor bar #3210 (Page 9, Key 2) is pre-set at the factory for
1.
average pools. It may be necessary to readjust the height of the sensor bar for the
machine to operate satisfactorily in your pool.
In “Free Form” or “Bowl Shaped” pools, the sensor bar may have to be raised to a
2.
higher setting to allow the machine to climb out of the deep end and clean up the
radius or slope as far as possible without the machine turning over.
Adjustment of the sensor bar #3210 (Page 9, Key 2) is made by loosening adjust-
3.
ing arm bolts #2121 B (Page 9, Key D) located just ahead of the intake. With the
machine sitting on a level surface, loosen both adjusting arm bolts, and move sensor
bar to desired position. Make certain the sensor bar is parallel to the level surface
and retighten the adjusting arm.
It may be necessary to reset the sensor bar several times to find the best position
4.
for operation in your pool. Sensor bar should glide freely. This can be checked by
pushing back on the sensor bar which will activate the reversing arms.
OPERATING INSTRUCTIONS
Select nearest grounded outlet supply of 110/115/220/240 voltage.
1.
CAUTION: avoid overloaded circuits as low or high voltage can damage your motor. A connected ground is most important. Plug into outlet. Observe machine as it
travels over bottom of pool.
Allow machine to travel around the pool until it is clean. Average 75' x 150' pool will
2.
required approximately 4 hours. If the pool has a heavy accumulation of debris, it
may be necessary to clean the filter several times during the vacuuming period.
Upon completion of vacuuming the pool, allow the unit to travel to the shallow end
of the pool. Before it reaches the pool wall, turn power off, raise the unit by the white
3.
nylon rope #1312, then remove the unit from the water by use of the handle. Allow
excess water from the filter to drain into the pool with the KingShark2 resting on the
edge or coping. Do not leave machine in water after disconnecting.
3
Loading...