Hayward HLWALLMOUNT Owner's Manual
Hayward Pool Products
620 Division Street, Elizabeth NJ 07207
www.hayward.com
Wired Wall Mount Terminal
Touchscreen Terminal for OmniLogic
Owner's Manual
HLWALLMOUNT
Contents
Description............................2
Installation............................3
Conguration.........................6
Operation..............................6
092523 RevA
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Hayward could void the user’s authority to
operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio / TV technician for help.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The term “IC” before the certification / registration number only signifies that the Industry Canada
technical specifications were met.
1
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Description
The HLWALLMOUNT is a remote touchscreen terminal that wires directly to the OmniLogic pool
automation controller. It is designed to fasten to a wall giving the user convenient access for
monitoring and controlling their pool. Up to two HLWALLMOUNTs can be installed and connected
to the OmniLogic. After installation, the OmniLogic will detect the new HLWALLMOUNT(s) and
automatically configure itself to utilize the new terminal(s).
Compatibility
The HLWALLMOUNT is compatible with all OmniLogic pool controls.
Before You Begin
Included:
• HLWALLMOUNT Remote Terminal
What you'll need:
• mounting screws/anchors
• an appropriate length of 4 conductor, 20 - 24AWG twisted pair wire (CAT3 or better pre-
ferred but not mandatory) for connecting the HLWALLMOUNT to the OmniLogic
• wirecutter/wirestripper
• tools for mounting, small flathead screwdriver for screw terminals
The HLWALLMOUNT must be mounted indoors or in a weather protected area (rain should never
be in contact with the touchscreen).
When considering a potential mounting location, survey the wiring route from the OmniLogic to
the HLWALLMOUNT. Ensure that you can successfully run an uninterrupted length of 4 conductor wire. Although various types of wire can be used, 4 conductor, solid 22AWG phone cable
is recommended. Refer to the table below for limitations on wire run lengths. When selecting
a location, note that the connecting the OmniLogic to the HLWALLMOUNT must not exceed the
recommended lengths shown in the chart below.
Up to two HLWALLMOUNTs can be wired to the OmniLogic. If wired in parallel, both units can
be wired up to the maximum distance shown below. If daisy chained, the furthest unit can not
exceed the maximum distance shown below.
20 AWG 22AWG 24AWG
Maximum Distance 450ft / 140m 285ft / 85m 180ft / 55m
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
Loading...