HAYWARD C2000, C3000, C4000, C5000 User Manual
SUPER STAR-CLEAR SPECIFICATIONS
MODEL
NO.
C2000
C3000
C4000
C5000
EFFECTIVE
FILTRATION
AREA
FT
2
200
300
400
500
M
2
19
28
37
47
DESIGN FLOW RATE
GPM
75
112
150
150
LPM
284
424
568
568
GPM
75
112
150
150
LPM
284
424
568
568
RESIDENTIAL PUBLIC
PRESSURE LOSS AT
DESIGN FLOW RATE
RESIDENTIAL PUBLIC
PSI
2.1
5.1
6.8
6.8
BAR
0.15
0.36
0.47
0.47
PSI
2.1
5.1
6.8
6.8
BAR
0.15
0.36
0.47
0.47
MAXIMUM
WORKING
PRESSURE
BAR
3.45
3.45
3.45
3.45
PSI
50
50
50
50
REQUIRED CLEARANCE
SIDE ABOVE
IN
18
18
18
18
CM
46
46
46
46
IN
18
18
18
22
CM
46
46
46
56
PARTS
Super Star-Clear
Models C2000, C3000, C4000, C5000
REF.
NO.
1
2
--3
4a
4b
4c
4d
5
6a
6b
6c
6d
7
8a
8b
8c
9
10
11
12a
12b
12c
12d
13
14a
14b
14c
14d
15
16
17
18
19
20
21
22
NO.
REQ’D.
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
4
4
4
4
1
1
1
2
2
2
2
2
MODEL
NUMBER
ECX270861
DEX2400S
DEX2400Z3A
SX200Z5
DEX2400BT
DEX3600BT
DEX4800BT
DEX6000BT
DEX2400J
DEX2400J4
DEX2400JS
DEX2400J3
DEX2400JN
DEX2400K
CX2000DA
CX3000DA
CX5000DA
CX3000F1B
CX3000FB
DEX360M
CX800Z4
CX3000Z3
CX4000Z3
CX5000Z3
CX3000J
CX470XRE
CX570XRE
CX870XRE
CX1260RE
CX3000C
DEX2400A1T
SPX1022C
SX360Z1
DEX360FB
SX200Z4
SX240F
SX200R
DESCRIPTION
Pressure Gauge
Relief Valve/Gauge Adapter Assy.
O-Ring for Relief Valve Stem (Set 3)
Relief Valve Assembly O-Ring
Filter Head (C2000)
Filter Head (C3000)
Filter head (C4000)
Filter Head (C5000)
Clamp Assembly
Washer w/Small Hole
Spring
Washer w/Large Hole
Brass Sleeve Nut
Filter Tank O-Ring
Top Closure Plate (C2000)
Top Closure Plate (C3000, C4000)
Top Closure Plate (C5000)
Inlet Elbow
Outlet Elbow
O-Ring
Air Relief Tube
Air Relief Tube
Air Relief Tube
Air Relief Tube
Air Tube Screen
Cartridge Element (C2000)
Cartridge Element (C3000)
Cartridge Element (C4000)
Cartridge Element (C5000)
Bottom Collector Manifold
Filter Body
1-1/2” Drain Plug w/O-Ring
O-Ring
Bulkhead Fitting
O-Ring
1-1/2” SKT. x 2” SLIP Connector
Locknut
PUMP SELECTION AND LOCA TION
To power your filter, select a continuous duty pump designed
for swimming pool or spa service.
It is important to first determine where your pump and filter will
be located. If above the water line, a self-priming pump must
be used. Self-priming pumps (
such as Hayward Super Pump®,
Super II™ or Max-Flo™
) have the ability to lift water from a
lower level and prime automatically.
Select a pump with an average output range suitable for the filter's
capacity. Other considerations are operation of hydrotherapy
fittings, automatic cleaners, etc. Your dealer will help you
select the proper size pump for your system.
FILTER LOCATION
Since plumbing fittings offer a resistance to water flow,
position the filter as close to the swimming pool as practical.
Keep the number of fittings to a minimum. Select a
well-drained area, one that will not flood when it rains.
The filter should be placed on a
level
concrete slab, very
firm ground, or equivalent, as recommended by your pool
dealer. Allow a top clearance for cartridge removal of 18”
(457 mm) for C2000, C3000 and C4000, 22” (559 mm) for
C5000. Be sure filter, pump, drain and pressure gauge are
accessible for convenient operation.
Position filter so the tank can drain by gravity.
If practical, place pump and filter in the shade to shield it
from continuous, direct heat from the sun.
PLUMBING
Use 1-1/2” or 2” piping. Connections are 1-1/2” socket
(solvent weld) or 2” male slip. We suggest unions be
provided for easy servicing.
Refer to the diagram for typical installation. Ball valves are
recommended where needed. While all systems vary, the
main consideration is to provide the desired control of
water flow from the pool to the pump and filter and back to
the pool. When the filter is located below the water level,
provide valves to prevent back flow of water to the filter
during cleaning and routine servicing.
Connect the pool suction plumbing between the skimmer,
pool outlet, etc., and the pump.
Install the pool return plumbing.
If pressure gauge is not installed, apply Teflon tape to the
gauge threads, and
carefully
screw the gauge into the
gauge adapter assembly.
A filter drain plug is furnished with each filter and is all that
is needed for complete filter draining. A manual air vent
valve is furnished to aid in bleeding off unwanted air when
starting the filter. The auto air relief provides air removal
during operation.
All electrical connections should be made in accordance
with local codes.
Check for joint leaks before operating.
Refer to pump instruction booklet for pump information.
NOTE: ANSI/NSPI-4 Article V, standard for above-ground and
on-ground pools, advises that components such as the
filtration system, pumps and heater be positioned so as to
prevent their being used as a means of access to the pool by
young children.
BEFORE STARTING THE FILTER
Superchlorinate the pool water by adding unstabilized granular
or liquid chlorine. Stabilized forms of chlorine are recommended
for normal daily use after the initial clean up of the water.
Follow chemical manufacturer’s recommendations for
superchlorination and daily use.
ISC2000-98
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
8.
9.
OWNER’S GUIDE
MODELS C2000, C3000, C4000, C5000
Hayward Super Star-Clear filters are high performance swimming pool filters with filtration ratings to 9000
gallons (34 KL) per hour. Manufactured from durable, corrosion-proof materials, they are designed for
continuous or intermittent operation, for installation above or below the pool water line, for fresh or salt water
swimming pools or spas. Star-Clear filters utilize multiple reusable, reinforced polyester filter cartridge
elements to provide a high degree of water clarity and long filter cycles with absolute minimum care.
31-3/4”
(807 mm)
36-1/2”
(927 mm)
42-1/2”
(1080 mm)
48-1/2”
(1232 mm)
C2000
C3000
C4000
C5000
Loading...