Hayter Mowers 100D User Manual

(English Version)
CODE FROM SERIAL NO:
100D 260000001 HANDBOOK: 111-0444(REV .A.)
ISSUE: 28.11.05

OWNER'S HANDBOOK

Envoy

CODE

100D

111-0444(A) 19/1/06 8:55 am Page 1.1

1.2

MAIN FEATURES /SPECIFICATIONS

Code 100D
Supply 220-240V~50Hz
Rated Input 1.4 kW
Fuse Rating 13A
Weight 23 Kg
Cutterblade Speed 2800 rpm
Cutting width 360mm
Cutting height 13 - 60mm
Overall dimensions 1,360mm x 450mm x 1,040mm

1 Handlebar Securing Knob.
2 Cable.
3 Switch Control Unit.
4 Bail Arm.
5 Handlebar.
6 Cable Cleat.
7 Grassbag Assembly.
8 Rear Deflector.
9 Serial No. Decal.
10 Height of Cut Lever
11 Motor Housing

Specifications

Main Features

111-0444(A) 19/1/06 8:55 am Page 1.2

4

3

5

1

11

8

1

9

10

6

2

1

7

1.2 Main Features/Specifications

1.3 Contents

1.4 Introduction

1.5 Warranty

1.6 - 1.9 Safety Precautions

1.9 Safety Symbols

1.9 Control Symbols

1.10 Assembling the Mower

1.10 - Delivery Checklist

1.10 - Handlebar

1.10 - Grassbag Attachment

1.10 - Supply Cable

1.11 - 1.15 Operating The Mower

1.11 - Electrical Connections

1.11 - Starting

1.11 - Forward Travel

1.11 - Turning

1.12 - Stopping

1.12 - Height of Cut

1.12 - Before Mowing

1.13 - Grassbag

1.13 - Without Grass Collection

1.13 - Heavy Growth

1.13 - Non-Grassed Areas

1.14 - Safe Mower Practice

1.15 - Overloading Protection

1.16 - 1.17 - Lawn Care Calendar - Guide Only

1.17 - Lawn Stripes

1.18 Maintenance Schedule

1.3

1.19 - 1.22 Mower Maintenance

1.19 - Deck Housing

1.19 - Securing Nuts and Bolts

1.19 - Lubrication

1.19 - Motor

1.19 - Switch Control Unit

1.20 - Cutterblade Removal

1.21 - Cutterblade Sharpening

1.21 - Supply Cable

1.22 - Storage

1.23 - 1.24 Trouble Shooting

1.25 EC Declaration of Conformity

1.26 - 1.27 Parts List

1.28 Parts List Diagram

1.29 - 1.31 Notes

1.32 Customer Info

CONTENTS

111-0444(A) 19/1/06 8:55 am Page 1.3

1.4

INTRODUCTION

Thank you for purchasing a Hayter mower. The following pages are designed to help you gain
safe and efficient service from your mower.

IMPORTANT: This ‘Owners Handbook’ should be regarded as part of the mower as it gives
essential information regarding mower safety, operation, maintenance and specifications. Read
and understand this handbook prior to operating your mower for the first time. Make sure you
are familiar with all the controls and points of regular maintenance. If you have any doubts,
consult your local Hayter authorised dealer who will be pleased to give you assistance.

IMPORTANT: This mower is designed solely for use in a domestic grass cutting
environment. Use in any other way is considered as contrary to the intended use. Compliance
with and strict adherence to the conditions of operation, service and repair as specified in this
handbook also constitute essential elements of the intended use.
This mower should be operated, serviced and repaired only by persons who are familiar with
its particular characteristics and who are acquainted with the relevant safety procedures.

The safety precautions listed in this handbook and all other generally recognised regulations on
safety must be observed at all times.
Any arbitrary modifications carried out to this machine may relieve Hayter Limited of
liability for any resulting damage or injury.

Hayter mowers are robustly constructed and designed for efficient economical
performance under normal mowing conditions. Correct operation and maintenance will ensure
a long and satisfactory service life. Prior to despatch from our factory every effort is made to
ensure that your mower is delivered in perfect condition.

Throughout this handbook all references to left and right are as viewed from behind the han­dlebar, in the direction of forward travel.

This handbook is based on information available at the time of publication.

HAYTER LIMITED reserve the right to amend product specifications without prior notification.

111-0444(A) 19/1/06 8:55 am Page 1.4

1.5

WARRANTY

LIMITED WARRANTY

Hayter Limited warrants to the original user/purchaser that this unit shall be free from
defects in material or workmanship under normal use for a period of two years from the
date of purchase. To qualify for the full benefit of the warranty, the warranty registration
card must be returned to Hayter Limited within 14 days of purchase. If the selling dealer
has not returned the Warranty Registration Card which is attached to the rear of the Owners
Handbook please complete and return. Subject to the conditions and exclusions noted in
this limited warranty, we shall at our option, repair or replace any warranted part during the
applicable period. If you are in any doubt or experience any difficulty, please consult a
Hayter Authorised Service Dealer for clarification.

A 90 day warranty period applies to those items which are subject to normal wear and tear
e.g. wheels, cutterblades, cables, grassbags and other consumable wearing parts.

This warranty does not apply to any unit that has been tampered with, altered, misused,
abused or used for hire, and will become invalid if non genuine Hayter parts are fitted. This
warranty does not cover minor mechanical adjustments unless they are due to defective
material or workmanship. Consult the Owner's Handbook or a Hayter Authorised Service
Dealer for assistance when making these adjustments.

The machines are not warranted for commercial use.

To make a warranty claim, return the unit to a Hayter authorised service dealer along with
proof of purchase stating the machine serial number and date of purchase. Subject to the
conditions and exclusions in this limited warranty, the authorised dealer will, at our option,
repair or replace any warranted part within the duration of the warranty period.

This limited warranty gives specific legal rights and is in addition to any statutory rights to
which you may be entitled and your statutory rights are not affected by this warranty. If
you need additional information concerning this written warranty, or assistance in obtain­ing services, please write to: Hayter Limited, Service Department, Spellbrook, Bishop's
Stortford, Hertfordshire, CM23 4BU

UK ONLY: Details of your local Hayter authorised dealer are contained in The Yellow
Pages or contact:- Freephone 0800 616298: or visit the Hayter website at
www.hayter.co.uk

111-0444(A) 19/1/06 8:55 am Page 1.5

1.6

SAFETY PRECAUTIONS

This safety alert symbol indicates important safety messages. When
you see this symbol be alert to the possibility of injury. Carefully read
the following and inform others.

Your mower is perfectly safe if used correctly. Failure to observe the
following precautions may result in serious injury.

Read the instructions carefully. Ensure that you are familiar with the
controls and the proper use of the equipment. Learn how to stop the
mower quickly in an emergency.

Never allow children or people unfamiliar with these instructions to
use the mower.

Never mow while people, especially children, or pets are nearby.

Keep in mind that the user is responsible for accidents or hazards
occurring to other people or their property.

It is recommended that a high sensitivity Residual Current - Operated
Circuit - Breaker (RCCB) with a trip current of not more than 30mA
is installed at the mains power socket. This will provide the user with
additional protection against electric shock. The fuse installed in the
plug only provides protection for the electrical equipment and will not
safeguard against electrocution. Always check the RCCB before using
the mower.

WARNING: Regularly inspect the supply cable for signs of damage
or ageing. Replace immediately if defective.

Always wear substantial footwear and long trousers while mowing. Do
not operate the equipment when barefoot or wearing sandals.

Thoroughly inspect the area where the mower is to be used and remove
all stones, sticks, wires, bones and other foreign objects.

Safety Alert Symbol

Preparation

Training

111-0444(A) 19/1/06 8:55 am Page 1.6

1.7

PRECAUTIONSSAFETY

Always ensure that the mower is in a safe operating condition.
Frequently check all nuts, bolts and screws for tightness. Use only gen­uine Hayter parts.

A damaged cutterblade and loose fixing bolt are major hazards. Before
use, visually inspect the cutting mechanism to ensure that it is in good
condition. A damaged cutterblade must be replaced immediately with
a genuine Hayter replacement part. Cutterblades which are slightly
worn can be resharpened. Ensure that both cutting edges are resharp­ened equally to maintain balance.
An unbalanced cutterblade may cause serious damage to your
machine.
Refer to "Maintenance."

SWITCH OFF AND REMOVE PLUG FROM MAINS.

- Before clearing blockages or unclogging the discharge chute.

- Before cleaning, checking or working on the mower.

- Whenever you leave the mower.

- After striking a foreign object. Inspect the mower for damage
and make repairs before re-starting and operating the mower.

- If the mower starts to vibrate abnormally (check immediately).

- If the supply cable is entangled.

THE CUTTERBLADE CAN CONTINUE TO ROTATE AFTER
THE MACHINE IS SWITCHED OFF.

Keep the supply cable clear of the cutterblade at all times.

Do not mow across the supply cable. Immediately disconnect the cable
from the mains supply if this occurs and check for damage. Do not use
a defective supply cable.

Mow only in the daylight or in good artificial light.

Avoid using the mower on wet grass, where feasible.

Always be sure of your footing on slopes.

Walk, never run.

Mow across the face of slopes, never up and down.

Exercise extreme caution when changing direction on slopes.

Do not mow excessively steep slopes.

Operation

Preparation

111-0444(A) 19/1/06 8:55 am Page 1.7

1.8

Use extreme caution when reversing or pulling the mower towards you.

Switch off if the mower has to be tilted for transportation when cross­ing surfaces other than grass and when transporting the mower to and
from the area to be mowed.

Never operate the mower unless the guards are securely in position and
in good condition.

Start the mower carefully, with feet well away from the cutterblade.

Do not tilt the front of the mower more than is absolutely necessary
when starting.
Never lift the rear of the mower.

Do not put hands or feet near or under rotating parts.

Never pick up or carry a mower while it is running or connected to the
mains supply.

Do not lift the rear deflector plate whilst the mower is in operation,
particularly when using without a grassbag.

Keep all nuts, bolts and screws tight to ensure that the mower is in a
safe working condition. (For torque settings refer to mower mainte­nance).

Carefully examine the supply cable for signs of damage or ageing.
Replace immediately if defective.

Check the grassbag frequently for wear or deterioration and replace if
necessary.

Wear strong work gloves when removing and reassembling the cut­terblade.

Replace worn or damaged parts for safety.

SAFETY PRECAUTIONS

Operation

Maintenance & Storage

111-0444(A) 19/1/06 8:55 am Page 1.8

1.9

SAFETY PRECAUTIONS

Safety Symbols

Safety Alert - Be aware to the
possibility of injury.

Danger of severing toes or fin­gers in cutting mechanism.

Carefully read the Owners
Handbook before using the
machine.

Danger of being hit by thrown
objects.

Switch off and remove plug
from mains before performing
maintenance or repair work.

Keep bystanders at a safe dis­tance from the mower.

Switch ON / OFF

(Symbol)

Height of Cut Adjustment

(Symbol)

Control Symbols

305113

Do not use in rain or in wet
conditions.

Wait until all machine compo­nents have stopped before
touching them.

STOP

CAUTION - PREVENT ENVIRONMENTAL DAMAGE: This mower has a
separate collection mark. This indicates at the end of its life the mower
must be taken to an authorised disposal site. It must not be disposed of with
general waste. See page 1.22 for more detail.

Danger of Electrical shock,
electrocution.

111-0444(A) 19/1/06 8:55 am Page 1.9

1.10

ASSEMBLING THE MOWER

Remove the mower from the packaging and check that the following
items have been supplied correctly. If any items are missing contact,
your local Hayter dealer.

1. Instruction Sheet 2. Grassbag Frame 3. Grassbag Top Cover

4. Grassbag Fabric 5. Supply Cable

To prevent accidents cut off the long ribbon attached to the grass­bag and discard.

Unscrew the handlebar securing knobs sufficiently to allow the handle­bar to pivot. Unfold the handlebar to the operating position. Tighten all
handlebar knobs to secure the handlebar in position.

Take care to ensure that the power cable does not become snagged at
the pivot points.

Once the grassbag is assembled. Raise the rear deflector, pass the
grassbag under the handlebar and hook in position. Lower the deflec­tor to rest on the grassbag.

Route the supply cable loosely across to the cable cleat on the left side
of the handlebar. Make a loop in the supply cable and secure to the
cable cleat.

Handlebar

Delivery Checklist

Grassbag Attachment

Supply Cable

111-0444(A) 19/1/06 8:55 am Page 1.10

1.11

Forward Travel

Position the mower on the grass area to be cut. Carefully uncoil the
supply cable clear of the mower. Ensure that the mains socket is
switched 'OFF' before connecting. Switch 'ON'.

Note: We recomend the use of a RCCB unit- Refer to "Safety
Precautions" - Preparation.

Locate the bail arm lever mounted on the handlebar and ensure that
your feet are clear of the mower deck. Depress the safety button with
the right hand and pull the bail arm towards the handlebar with the left
hand. The motor will now start.

Hold and push against the handlebar with both hands to move the
mower forwards.

To make a wide turn steer the mower with the handlebar whilst travel­ling forward.

To make a tight turn apply downward pressure on the handlebar to
raise the front wheels of the mower just above ground level and steer
the mower using the handlebar in the required direction.

To prevent accidents do not raise the front of the mower exces­sively when making a turn. Never raise the rear of the mower
when the motor is running.

MOWERTHEOPERATING

Turning

Starting

Electrical Connection

111-0444(A) 19/1/06 8:55 am Page 1.11

Stopping

Release the bail arm to stop the motor.

WARNING: AVOID ACCIDENTS - The cutterblade may contin­ue to rotate after the mower is switched off

Move the height of cut lever sideways to disengage it from the locking
notch, then push forwards to lower or pull backwards to raise the height
of cut. Release the lever in the required position and ensure that it locks
firmly into one of the seven notch settings.

Always select a height of cut to suit operating conditions. Prevent
motor overloading and blockages by avoiding low cuts in long grass
conditions. Be prepared to make two cuts when the grass is long.

To prevent accidents thoroughly inspect the area and remove all
objects which when contacted by the mower cutterblade could
become dangerous projectiles. Inspect the area for hidden obstruc­tions which when contacted by the cutterblade could risk health
and safety. Remember the location of these obstructions and
ensure that you mow around them.

1.12

Height of Cut

Before Mowing

305113

OPERATING THE MOWER

111-0444(A) 19/1/06 8:55 am Page 1.12

1.13

To empty the grassbag raise the rear deflector and pass the grassbag
under the handlebar and lower the rear deflector to rest against the rear
of the mower.

Pour out the grass clippings and shake the grassbag vigorously to clean
the airways. Good grass collection depends on good air flow through
the grassbag. When collecting grass clippings it is important that the
grassbag is emptied regularly to prevent blockages and motor over­loading.

Remove the grassbag and operate the mower with the rear deflector in
the closed position.

Areas of heavy growth should be mown without collecting the clip­pings. If collection is required, first mow the area without the grass­bag at the maximum height of cut setting. Allow the grass clippings to
dry out and then mow the area at the maximum height of cut setting
with the grassbag fitted. Reduce the height of cut and mow the area
again as necessary until the required finish is obtained.

To prevent grass damage do not remove more than one third of grass
height in one cut.

When moving the mower across non-grassed areas, stop the motor and
set the mower to the maximum height of cut to protect the cutting
mechanism.

Heavy Growth

305113

Non-Grassed Areas

MOWERTHEOPERATING

Without Grass Collection

Grassbag

111-0444(A) 19/1/06 8:55 am Page 1.13

1.14

WARNING: PREVENT ACCIDENTS -Take extreme care do not
mow across the supply cable. If this should occur, switch off immedi­ately and disconnect the plug from the power supply. Carefully exam­ine the cable for cuts and damage. A defective cable must be replaced
before the mower is used again. Always be aware of the location of the
supply cable in relationship to the mower and the grass area. Do not

allow the cable to become hidden in uncut grass. Keep the cable over
the cut area at all times. A cable which is out of sight is out of mind
and this could lead to a hazardous situation. Plan a 'cutting scheme'
which works away from the power supply point and ensures that the
cable is trailed out over the cut area. Work up and down the lawn in
rows. Turn the machine round at the end of the row and step across the
cable so that the cable is trailed along in the cut area on the return run.

When working around flower beds, prevent the cable from trailing
across the cultivated area by positioning a stake at the corner of the
bed. Do not allow the cable to be pulled around sharp obstructions.
Stop mowing immediately if cable resistance is felt and remove the
obstruction. Do not allow the cable to become entangled.

WARNING: PREVENT ACCIDENTS - Switch off at the mains,
remove the plug before adjusting, cleaning or if the cable is entan­gled.

Safe Mower Practice

OPERATING THE MOWER

111-0444(A) 19/1/06 8:55 am Page 1.14

Overloading Protection

1.15

Do not let the motor labour or slow down through being overloaded in
work. When this situation occurs, raise the front of the mower slightly
by bearing down on the handlebar, allow the motor to reach maximum
speed and proceed to mow at a slower pace. Alternatively readjust to a
higher cut position. If the motor continues to labour, switch off and
remove the plug from the mains supply. Remove and empty the grass­bag. Examine the discharge chute and remove any blockage. Turn the
machine on its side and clear any obstruction from the cutterblade and
the underside of the mower deck. Place the machine upright and
replace the grassbag. Readjust to a higher cut position if necessary.
Restart the mower and proceed to mow at a pace which does not over­load the mower.

IMPORTANT: PREVENT DAMAGE - DO NOT continue to
operate the motor in an overloaded condition. If this does occur,
stop mowing and allow the motor to run at maximum speed for
one minute. This will allow the motor to cool down to its normal
working temperature.

MOWERTHEOPERATING

111-0444(A) 19/1/06 8:55 am Page 1.15

1.16

There is very little work to do this month apart from brushing away
leaves. Keep off the grass if frozen or waterlogged.

Rake the grass thoroughly. Spike the lawn to aerate and stimulate soil
organisms and root growth and apply lawn sand if necessary.

The yearly lawn work programme really starts this month. As soon as
the ground conditions are suitable, the first cut can be made. The first
cut should merely “top” the grass as close cutting at this stage could
result in severe yellowing or browning. Two cuts are generally suffi­cient this month.

Mow often enough to stop grass growing away. Dig out patches of
coarse grass or resistant weed. Re-seed bare patches.

Keep mowing increasing the frequency as required. Treat with selec­tive weed killers or combined weed/feed preparations if you did not
feed the lawn in April.

Summer mowing should now be under way. It should be necessary to
mow the lawn twice a week. Raking before mowing is important this
month as the combined action keeps runners of clover under control.
Water the grass if necessary, and remember to soak thoroughly.

Treat the grass with the second application of fertiliser or weed
killer/fertiliser. Water when necessary and rake occasionally. As a gen­eral rule the grass clippings should be removed each time you mow. If
weather conditions are dry and hot and the grass is weed free, leave the
clippings on the lawn to help maintain ground moisture.

January

LAWN CARE CALENDAR

February

March

April

May

June

July

To be used as a guide only.

111-0444(A) 19/1/06 8:55 am Page 1.16

1.17

Keep mowing regularly and watering as necessary. Fill any cracks
caused by drought with a mixture of sharp sand and soil. In dry weath­er conditions leave the grass longer to help retain ground moisture.

Raise the height of cut to allow the grass to thicken and protect the
roots from the winter frost and snow.

Rake out the thatch from the turf and spike the lawn to assist in
drainage. Brush in peat and sharp sand.

Use a stiff broom to disperse worm casts before mowing. Keep turf
free from leaves.

Apart from brushing away leaves, December is a slack end of a busy
year. Keep off the lawn if it is very wet or frozen.

The way to achieve a neat striped effect is for the lawn being cut in
parallel stripes, alternate stripes being mown in opposite directions. A
much more important routine is to cut at right angles to the line of the
previous mowing. If the work has been carried in a north-south line,
then the next cutting should be in an east-west direction. The cross­cutting keeps down the coarse weed grasses.

To prevent grass damage do not remove more than one third of the
grass height in one cut.

CALENDAR

August

LAWN CARE

September

October

November

December

1

2

1CG480V05A

Lawn Stripes

111-0444(A) 19/1/06 8:55 am Page 1.17

1.18

Follow the hourly or calendar intervals, whichever occurs first. More
frequent service will be required if working for prolonged periods
under dusty, dry conditions, or when airborne debris is present or after
extensive operation cutting tall, dry grass.

Remove grass debris from around the height of cut ratchet, air filter in the
cowl and the underside of the deck housing.

Remove grass debris from the grassbag and check for signs of damage.

Check the condition of guards and safety devices.

Check condition of cutterblade.

Lubricate wheels, pivot points and linkages.

Sharpen the cutterblade.

Flash test (Dealer) to ensure complete safety.

Check cables/switch and connection

Replace air filter

MAINTENANCE SCHEDULE

25-50Hrs or Every Season

Daily

111-0444(A) 19/1/06 8:55 am Page 1.18

1.19

Remove grass debris from the top and underside of the deck housing
immediately after use.

Regularly check that all securing nuts and bolts are tight. Replace
missing or damaged items immediately.

Bolt - Cutterblade fixing Torque 20Nm
Plastic Screws - Bottom of Handlebar Torque 3.5Nm
General Screws - Used on plastic parts 1.5Nm (Note: Use manual
handtools only).

Lubricate the wheels, pivot points and linkages with engine oil every
25 operating hours.

The motor is maintenance free.

The switch control unit is maintenance free.

1CG480V36B

Securing Fasteners

Deck Housing

MOWER MAINTENANCE

Lubrication

Motor

Switch Control Unit

111-0444(A) 19/1/06 8:55 am Page 1.19

1.20

1

2

Turn the mower on its side.

Firmly grip the end of the cutterblade (2) with a gloved hand and
remove bolt (1). When replacing ensure that the new cutterblade is the
correct way up with the turned edges facing towards the motor before
locating onto the two carrier pins. Secure the cutterblade fixing nylon
bolt and tighten to the specified torque of 20Nm.

The cutterblade has sharp edges. ALWAYS wear strong gloves to
protect your hands when working on the cutterblade. DO NOT
rotate tools towards the cutting edges to avoid the risk of injury
should the tool slip. ALWAYS use genuine Hayter replacement
parts.

The condition of the cutterblade and its mounting arrangement should
be checked regularly for signs of wear or damage. Ensure that the cut­terblade is not bent or cracked.

A damaged cutterblade that is out of balance will vibrate excessively
and may break. DO NOT use an unbalanced cutterblade.

Regularly check that the bolt securing the cutterblade is tightened
to the specified torque of 20Nm.

Replace the cutterblade every 2 years or sooner if excessively worn or
damaged.

To prevent injury it is wise to seek assistance when turning the mower
on its side.

Cutterblade Removal

MOWER

MAINTENANCE

111-0444(A) 19/1/06 8:55 am Page 1.20

30°-45°

Cutterblade Sharpening

A slightly worn cutterblade may be re-sharpened. Both blade edges
must be sharpened equally to ensure balance. Sharpen the cutterblade
every 25 mowing hours or more frequently if conditions require.
Remove the cutterblade from the mower and clean using a brush and
water. Inspect the cutterblade for signs of damage. Sharpen both cut­ting edges with a flat file to restore performance.

Ensure that the cutterblade is balanced. Use a screw driver with a
round shaft to support the cutterblade through its centre hole. Hold the
cutterblade horizontal and then release. A balanced cutterblade will
remain horizontal.

If the cutterblade is not balanced the heavy end will rotate downwards.
Sharpen the heavy end until the cutterblade is correctly balanced.

Check the condition of the supply cable for damage or ageing. Replace
immediately if defective.

1.21

MOWER MAINTENANCE

Supply Cable

111-0444(A) 19/1/06 8:55 am Page 1.21

1.22

Handlebar storage: To collapse the handlebar first unscrew the two
top securing knobs to allow the top section of the handlebar to pivot
forward to rest against the middle section then unscrew the bottom two
securing knobs sufficiently to allow both top and middle sections to be
folded forwards.

Storage for long periods: To ensure your mower is maintained in
good working order it is important that the following procedure is
adopted when the mower is stored for periods in excess of one month.
Refer to the Maintenance section as necessary.

Clean all areas of the mower and ensure that the grassbag is clean.

Lubricate the mower.

Treat metal parts with a water repellent anti-corrosion product.

Lower the handlebar if desired.

Cover the mower with a protective sheet and store it in a dry area.

Rest the mower deck on wooden blocks to remove the weight of the
mower from its wheels / roller.

Storage

MOWER

MAINTENANCE

EU Directive 2002/96/EC classifies this product as an electrical or electron­ic equipment.
(a) This equipment should not be disposed of as unsorted municipal waste.
(b) It should be taken to a designated collection point or recycling centre
and handled according to national laws in the area.
(c) The consumer has a critical role in returning waste electronic/electrical
equipment for recycling and disposal.
(d) Recycling keeps this equipment out of the municipal waste stream.
(e) The crossed-out bin symbol is a reminder to follow these points.
(f) Please contact your local authority or local dealer and ask for further
details regarding the correct method of disposal.

Please refer to Safety
Symbols on page 1.9

111-0444(A) 19/1/06 8:55 am Page 1.22

Test socket by plugging in anoth­er appliance.

Remove mower plug and check
RCCB action. Check the supply
cable for any obvious signs of
damage and replace immediately
if defective. If no obvious faults
are found a serious fault is indi­cated. Contact your Hayter
Dealer.

Re-engage plug.

Fit a new 13 amp fuse.

Disconnect from the mains and
check the supply cable for any ob­vious signs of damage. Replace
immediately if defective.

Disconnect from the mains and
remove any obstructions.

Ensure switch lever has returned
to the 'OFF' position. Disconnect
from the mains and contact your
Hayter Dealer.

Contact your Hayter Dealer.

Mains supply socket dead.

RCCB tripped.

Plug pulled out of mains
socket.

Fuse failure.

Supply cable damaged.

Cutterblade obstructed.

Faulty switch control unit.

Faulty brake unit.

1.23

PROBLEM POSSIBLE FAULT REMEDY

TROUBLE SHOOTING

Motor fails to start.

Motor will not stop.

Cutterblade runs on exces­sively after switching

'OFF'.

111-0444(A) 19/1/06 8:55 am Page 1.23

Motor vibrates excessively.

Uneven cut

Discharge chute blocks.

Mower is hard to push.

Poor grass collection.

1.24

Mounting bolts loose.

Cutterblade bolt loose.

Cutterblade out of balance.

Undulating ground contours.

Cutterblade worn.

Cutterblade out of balance.

Wheels / Roller damaged.

Grass is wet.

Cut height too low.

Grassbag full.

No airflow through the
grassbag.

Cut height too low.

Wheels / Roller damaged.

No airflow through the
grassbag.

Discharge chute blocked.

Wet grass.

Grassbag full.

Tighten bolts.

Tighten bolt.

Balance cutterblade.

Change direction of travel.

Sharpen the cutterblade.

Balance cutterblade.

Inspect and replace as necessary.

Mow dry grass.

Increase cut height.

Empty grassbag.

Clean the grassbag.

Increase cut height.

Inspect and lubricate or replace
as necessary.

Clean the grassbag.

Remove blockage.

Mow dry grass.

Empty grassbag.

PROBLEM POSSIBLE FAULT REMEDY

TROUBLE SHOOTING

111-0444(A) 19/1/06 8:55 am Page 1.24

1.25

111-0444(A) 19/1/06 8:55 am Page 1.25

EC DECLARATION OF CONFORMITY

Manufactured for: HAYTER LIMI TED,

Address: Spellbrook, Bishop’s Stortford, Herts. CM23 4BU. ENGLAND

declare that the lawnmower:

Model n ame:

Type:

Model No:

Cutting width:

Speed of ro tation of the cutting device:

Motor manufacturer:

Speedofrotationofengine:

Complies with the provisions of Directive: 98/37/EC Essential Health & Safety Requirements Relating to the Design &

Construction of Machinery and Safety Components, as amended and the regulations transposed into national law.

Also Directive 89/336/EEC Electromagnetic Compatibility , as amended and the regulations transposed into national law.

Also Directive 73/23/EEC Low Voltage, as amended and the regulations transposed into national law.

Also Dire c tive 2000/14/EC Noise emission in the environment by equipment for use outdoors and the regulations transposed into

national law.

Procedure applied for the conformity assessment: ANNEX VI, procedure 1.

Notified Body: TÜV Industrie Service GMBH – TÜV SÜD Group, Westendstraße 199, 80686 MÜNCHEN. Germany

Notified body identification No: 0036

Measured sound power level:

Guaranteed sound power level:

Complies with harmonized standards: EN 55014-1, EN 55014-2, EN 60335-2-77, EN 61000-3-2 and EN 61000-3-3

Signed

S.A Maryniak

(Technical Director)

Envoy
Pedestrian Rotary Electric Lawnmower
CODE 100D
360 mm
2800 rpm
ATB, Aus tria
2800 rpm

88 dB(A)

96 dB(A)

Date: January 2006
Declaration done and technical do cumentation kept at:
HAYTER LIMITED
Spellbrook, Bishop’s Stortford,
Herts. CM23 4 BU ENGLAND

VIBRATION INFORMATION

The v ibration level at the operator contact positions, measured in accordance with European S tandard EN 836

CODE 100D 6.1 ms

-2

1.26

1 Motor HY100001 1
2 Capacitor HY100002 1
3 Underdeck HY100003 1
4 Throw Plate HY100004 1
5 Wheel - Wide Assy HY100506 2
6 Bearing - Wheel HY100033 12
7 Hub - Cap HY100036 4
8 Starlock 12mm HY100047 4
9 Rod - Rear Axle HY100068 1
10 Wheel - Thin Assy HY100505 4
11 Lever - HOC HY100038 1
12 Spring - HOC HY100041 1
13 Rear Axle Assy HY100504 1
14 Plate - Axle Pivot HY100064 4
15 Screw - M4 HY100078 53
16 Bolt - Fixing Cutterblade 100013 1
17 Cutterblade HY100012 1
18 Carrier - Cutterblade 100014 1
19 Rod - Connecting HY100037 1
20 Starlock - 8mm HY100048 3
21 Axle - Front Assy HY100503 1
22 Fins - Front HY100006 1
23 Bolt - Motor HY100076 4
24 Cover - Main 111-0537 1
25 Decal - Hayter 410087 1
26 Hoc - Screw Cover 111-0543 1
27 Moulding-Vent Mesh Support 111-0041 1
28 Decal - Envoy 111-0542 1
29 Cover Electric Trim 111-0538 1
30 Handlebar - lower 111-0540 1
31 Handlebar - Middle 100025 1
32 Handlebar - Upper 100024 1
33 Switch - Assy/ Trailing Lead 100515 1
34 Screw - M4 x 19 HY100128 1
35 Bail Arm HY100017 1
36 Mount - Bail Arm Assy HY100510 1
37 Hand Wheel - Assy 480088 4
38 Bolt - Handlebar HY100028 4
39 Deflector - Rear HY100007 1
40 Rod - Deflector 100126 1
41 Serial No Label --------- 1

PARTS LIST

ITEM NO.

QTY.

DESCRIPTION

PART NO.

ITEM NOTE

111-0444(A) 19/1/06 8:55 am Page 1.26

1.27

41 Spring - Deflector HY100009 1
42 Knob - HOC HY100039 1
43 Ratchet - HOC 111-0539 1
44 Washer - Spring M8 100119 4
45 Grassbag - Fabric/base 100513 1
46 Frame - Grassbag 100016 1
47 Top - Grass Bag HY100075 1
48 Screw - M6 x 20 HY100127 2
49 Bolt M10 x 30 HY100029 2
50 Fan - Motor Top HY100019 1
51 Spacer - Rear Wheel HY100030 6
52 Pin - Spring HOC HY100042 1
53 Spring - Counter Balance 100080 1
54 Cleat - Cable 100105 1
55 Terminal Block HY100077 1
56 Washer - Grip M10 HY100079 2
57 Vent Mesh Grille 111-0075 1
58 Cable - Tie 100023 4
59 Washer - M8 100106 4
60 Main Lead - 17m UK Assy HY100135 1
61 Decal Caution 111-0084 1

LISTPARTS

ITEM NO.

QTY.

DESCRIPTION

PART NO.

ITEM NOTE

111-0444(A) 19/1/06 8:55 am Page 1.27

1.28

PARTS LIST

111-0444(A) 19/1/06 8:55 am Page 1.28

35

33

58

37

58

58

37

15

29

28

24

25

50

15

1

57

42

43

55

31

38

27

15

30

41

15

56

49

2

38

39

38

37

61

48

40

26

46

41

3

15

38

37

36

15

32

54

47

45

15

34

15

60

20

59

44

23

15

7

8

10

6

22

15

15

7

18

6

17

14

21

15

14

15

19

15

15

6

8

15

10

6

51

14

16

19

20

10

6

6

8

4

15

51

15

11

15

53

52

20

15

51

14

15

7

5

6

6

5

51

13

12

6

10

6

6

51

9

8

7

2C100C02B

1.29

NOTES

Notes:-

111-0444(A) 19/1/06 8:55 am Page 1.29

1.30

NOTES

Notes:-

111-0444(A) 19/1/06 8:55 am Page 1.30

1.31

NOTES

Notes:-

111-0444(A) 19/1/06 8:55 am Page 1.31

Serial No:

Motor Type 220-240V~50Hz

(100D)

Date of Sale:-

Your Local Dealer:-

CUSTOMER

INFORMATION

111-0444(A) 19/1/06 8:55 am Page 1.32