Page 1
)
)
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
NO. OOO2076521 (0
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,
or part thereof, which shall appear to the Company upon inspection to be of defective
material or not of first class workmanship, provided that claim is made in writing to Haws
within areasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written authority from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential
damages claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
Model 7260B-7270B/7260BT-7270BT
Eye/Face Wash
LIMITED WARRANTY
No. 2080038(15
04/14 Model 7260B-7270B/7260BT-7270BT Page 1 of 4
Page 2
LOCATION OF UNIT: The Model 7260B/7260BT/7270B/7270BT Eyewash units
should be installed in close proximity to potential accident areas. It should be clearly
identified, free from obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1/2” IPS with 30-90 psi (2-6
ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter
is recommended.
PLUMBING CONNECTIONS: Inlet supply is female 1/2” IPS. Waste outlet is 1-1/2”
IPS.
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1. No flow. 1. Check the main shut-off valve.
2. Insufficient water flow. 2. a. Verify minimum 30psi flowing supply
line pressure.
b. Probable clogging of flow control due
to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble the head.
Clean flow control and reassemble
head. See SP65 Installation Drawing
for details.
c. Remove cap located on L – Strainer
using a 3/8” allen wrench to access
and clean filter screen.
3. Eyewash or face wash streams do
not meet desired eye level or are
not balanced.
3. Possible blocked flow control, see
above solution. Possible non-leveled
eyewash assembly.
4. Water does not drain properly. 4. Check the main waste line of your
building to see if it does handle the
capacity required for the entire
drainage system.
For more information about Haws products, see our website: www.hawsco.com
© 2014 Haws
HAWS
04/14 Model 7260B-7270B/7260BT-7270BT Page 2 of 4
®
®
Corporation – All Rights Reserved
and other trademarks used in these materials are the exclusive property of Haws Corporation.
Page 3
THIS DOCUMENT IS TRUE AND CORR ECT AT TIME OF PUBLICATION. CONTI NUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AN D M EASUREMENT S SUBJECT TO CHANGE WITHOUT N OTICE.
PARTS BREAKDOWN
SP93
BOWL
SP509
L-STRAINER
SP170
TEST TAG
SP65 EYE/FACE WASH
ASSEMBLY
(SEE DETAIL)
SP80
BRACKET
SP229 VALVE
ASSEMBLY
SP95
TRAP &
TAILPIECE
SP175
EYEWASH
SIGN
SP65 EYE/FACE WASH ASSEMBLY
(INCLUDES: EYE/FACE WASH HEAD ( )
EYEWASH H EAD (
NOTE:
CONTROL (
TRAP & TAILPIECE SU PP LIED WITH MODEL 7260BT & 7270BT ONLY.
BYECN NO.
REVISED PE R
ECN:
4910
DATE
DRAWN
RTM
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2014
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
7/17/02
DATE
HM
CHKD
MODEL(S)
1:1
SCALE:
7260B-7270B/7260BT-7270BT
DRAWING TYPE: SIZE: A
), DUST COVER (SHOWN)
PARTS BREAKDOWN
), EYEWASH FLOW
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAW S @HAWSCO. C O M
WEBSITE : W W W. H AW SC O .C O M
PAGE
PART NUMBER
0002080038
DRAWING NO.
15345A00 15
SHEET OF
11
3 of 4
REV
Page 4
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
C
Haws Corporation - All Rights Reserved.
2014
3 1/2 [89]
NOTES:
1. METRIC DIMENSIONS ARE IN BRACKETS [X].
2. TO COMPLY WITH ANSI Z358.1-2 00 9 FOR EMERGENCY EYEWASH OR EYE/FACE WASH:
- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES.
- EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED WITH NOZZLES NOT LESS THEN 83.8 CM ( 33 IN.) AND NO GREATER THAN
114.3 CM (45 IN.) FROM SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL OR NEAREST
OBSTRUCTION.
3. DIMENSIONS MAY VARY BY ± 1/2 [13].
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
3 [76]
MOUNT
DETAIL
WALL
3X ø1/4 [ø8]
1 [41]
3 3/4 [94]
4 1/8 [103]
11 1/4 [286]
14 1/2 [371]
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
MAX. 45" [1143]
MIN. 33" [838]
6" [154]
TOP VIEW
(SUPPLIED W/7260BT &
TAILPIECE 1-1/4" O.D.
1-1/2" (F) IPS WASTE TRAP
APPROVED:
DRAWN:
4161
SLS
REVISE D PER
ECN:
DATE:
5/1/08
4910
DATE:
CHK'D.:
BY:ECN NO.
HM
SCALE:
MODEL(S)
(SUPPLIE D W/7260BT &
7270BT ONLY )
7270BT ONLY )
L-STRAINER
1:1
7260B-7270B/7260BT-7270BT
DRAWING TYPE: SIZE: A
INSTALLATION
0002080038.D
PART NUMBER
DRAWING NO.
SHEET OF
15344A00 15
11
REV
14 1/8 [359]
8 1/2 [216]
OPTIONAL DUST
COVER
1/2" IPS
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
SUPPLY
10 3/8 [264] ±1 [25]
BRACKET FOR
PAGE
4 of 4
Loading...