Haws 3202, 3202G Installation, Operation & Maintenance Instructions Manual

No. 2077328 (25)

Model 3202/3202G

Drinking Fountain

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

HAWS warrants that this specific product is guaranteed against defective material
liability under this warranty shall be discharged by furnishing without charge F.O.B.

HAWS Factory any goods, or part thereof, which shall appear to the Company upon
claim is made in writing to Haws within a reasonable period after receipt of the

product. Where claims for defects are made, the defective part or parts shall be
cost of repairs, alterations or replacements, or for any expense connected therewith

made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective

or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential
damages claimed to arise under the contract of sale. The drinking fountain

to function if installation and maintenance

instructions provided are adhered to. The units also must be used for the purpose

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

or poor workmanship for a period of one year from date of shipment. HAWS

inspection to be of defective material or not of first class workmanship, provided that

delivered to the Company, prepaid, for inspection. HAWS will not be liable for the

materials

manufactured by HAWS is warranted
for which they were intended.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.

MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

LIMITED WARRANTY

12/17 Model 3202/3202G Page 1 of 4

TROUBLESHOOTING

PROBLEM

REPAIR CHECKLIST

1.

Insufficient bubbler flow.

1a.

Check that inlet screwdriver stop valve is in

b.

Verify minimum 30 psi flowing supply

c.

Clean strainer. See 5874 Series Valve

d.

Adjust valve to increase flow. Use front

RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12"
adjustable wrench, 10" pipe wrench, 5/64“ hex key wrench, 9/16”, 1/2", 7/16” socket
wrench or open end wrench.

LOCATION OF UNIT: The Model 3202/3202G Drinking Fountain is a wheelchair
accessible drinking water facility. The height dimensions shown, meet current ADA
requirements. When installing this unit, local, state or federal codes should be adhered
to. If height other than shown is required, then dimensions must be adjusted
accordingly.

SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6
ATM) pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.

PLUMBING CONNECTIONS: Inlet is 1/4" IPS male fitting.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual

for more information.

wide-open position.

pressure.

Manual.

adjust screw or see 5874 Series Valve
Manual.

General Notes:

Before tightening nut and ferrule assembly, push tubing into fitting until it bottoms out to
ensure correct engagement with O-Ring.

For more information about Haws products, see our website: www.hawsco.com

© 2017 Haws
HAWS

®

®

Corporation – All Rights Reserved

and other trademarks used in these materials are the exclusive property of Haws Corporation.

12/17 Model 3202/3202G Page 2 of 4