Page 1
)
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS, Sparks,
Nevada. HAWS will not be liable for any damages caused by defective materials or
poor workmanship, except for replacements, as provided above. Buyer agrees that
HAWS shall not be liable for general, special, or consequential damages claimed to
arise under the contract of sale. The drinking fountain manufactured by HAWS is
warranted to function if installation and maintenance instructions provided are
adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
Model 1152 Drinking Fountain
LIMITED WARRANTY
No. 2076728(9
04/14 Model 1152 Page 1 of 4
Page 2
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/64“ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open end
wrench.
LOCATION OF UNIT: When installing Model 1152 Drinking Fountain, local, state or federal
codes should be adhered to. If height other than shown is required, then dimensions must be
adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2” IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 1/4” female IPS. Waste outlet is female 1-1/4” IPS.
MAINTENANCE: Periodically clean the strainer.
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1. Insufficient bubbler flow. 1a. Check that inlet screwdriver stop valve
(not supplied) is wide open. Turn
counterclockwise.
b. Verify minimum 30 psi flowing supply
pressure.
© 2014 Haws
HAWS
®
®
Corporation – All Rights Reserved
and other trademarks used in these materials are the exclusive property of Haws Corporation.
04/14 Model 1152 Page 2 of 4
Page 3
THIS DOCUMENT IS TRUE A ND CORRECT AT TI ME OF PUBLICATION. CONTINUED PRODUCT IMPR OVEMENTS
MAKE SPECIFICATIO NS AND MEASU REMENTS SU BJECT TO CHANGE WITHOUT NOTICE.
0001235211.6
BUBBLER HEAD
6450
STRAINER
(NOT SHOWN)
0004290631
ROLL PIN
BYECN NO.
REVISED PER
2195
ECN:
DRAWN
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2014
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
D. OLLOM
APPROVED
4910
DATE
11/25/95
DATE
HM
CHKD
MODEL(S)
SCALE:
1:1
1152
DRAWING TYPE: SIZE: A
PARTS BREAKDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (7 55) 359-7424
E-MAIL: HAW S@H AW SC O .C O M
WEBSITE: WWW. HAWSCO.COM
PAGE
PART NUMBER
0002076728
DRAWING NO.
12791C00 9
SHEET OF
11
3 of 4
REV
Page 4
C
Haws Corporation - All Rights Reserved.
2014
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
(MOUNTING HARDWARE
NOT SUPPLI ED )
1. ROUGH-IN DIMENSIONS MAY VARY ± 1/4" (6.4mm).
2. WHEN INSTAL LI NG THIS UNIT, LOCAL, STATE OR FEDERAL CODES SHOULD
BE ADHERED TO FOR INSTALLATI O N DIMENSIONS (LOCATI O NS), WASTE AND
SUPPLY REQUIREMENTS OTHER THAN SHOWN.
FLOOR LI NE
MOUNTING HOLES
3X Ø
9.5mm
3/8"
44mm
1-3/4"
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
Ø
251mm
9-7/8"
98mm
3-7/8"
44mm
1-3/4"
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
927mm
36-1/2"
(TO SPOUT
OUTLET)
1048mm
41-1/4"
1013mm
39-7/8"
WASTE
826mm
32-1/2"
1-1/4" O.D.
WASTE
APPROVED:
DRAWN:
C. HAYES
REVIS ED PER
ECN:
DATE:
05/91
4910
DATE:
BY:ECN NO.
CHK'D.:
HM
SCALE:
MODEL(S)
INLET
76mm
3"
1/4" IPS(F)
343mm
13-1/2"
1:1
DRAWING TYPE: SIZE: A
1152
INSTALLATION
0002076728.D
PART NUMBER
DRAWING NO.
09404C00 9
SHEET OF
11
REV
216mm
1-1/4" IPS
WASTE &
TRAP
(NOT SUPPLIED)
WALL
FACE
(775) 359-4712 FAX (755) 359-74 24
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
PAGE
8-1/2"
4 of 4
Loading...